www.swagelok.com Metal asket ace Seal ittings /6 to and 6 to 8 mm sizes igh-purity stainless steels The original design, the authentic brand
2 Metal asket ace Seal ittings ontents lands Page 4 odies Page 7 Welded Assemblies Page 2 askets Page 3 Nuts, aps, and Plugs Page 4 Split Nut Assemblies Page 5 igh-low onnections Page 5 Lock and Tag evices Page 7 Installation Instructions Page 7 Materials of onstruction Material lands, odies, and Nuts 36 stainless steel 36L stainless steel 36L VAR (vacuum arc remelt) stainless steel askets Nickel 36L stainless steel opper Material esignator 36L 6LV NI U Applicable Specification ar stock: ASM SA479 ASTM A276 orged shapes: ASM SA82 ASTM A34 ar stock: ASM SA479 ASTM A276 orged shapes: ASTM A82 ASTM 62 ASTM A240, ASTM A67 ASTM 52 Pressure Ratings All ratings comply with calculations in accordance with ASM ode for Pressure Piping 3.3, Process Piping. To determine pressure ratings in accordance with ASM 3., Power Piping, multiply psig rating by 0.94. Working pressure ratings determined at room temperature with gasket materials shown. Plating female nuts are silver plated. Avoid chemical processes used for cleaning, electropolishing, and passivation that will remove plating. If the plating is damaged or removed, thread galling may occur, damaging fitting components and preventing a proper seal., in inches (millimeters), are for reference only and are subject to change. The dimension refers to the smallest nominal inside diameter of the part (see ordering tables). Temperature Ratings omponents Material Temperature, ( ) ittings askets Testing 36 stainless steel 36L stainless steel 36L VAR stainless steel 36L stainless steel Nickel opper 000 (537) 000 (537) 600 (35) 400 (204) The fitting design has been helium leak tested to a maximum leak rate of 4 0 9 std cm 3 /s with silver-plated and copper gaskets and to a maximum leak rate of 4 0 std cm 3 /s with unplated gaskets.
Ultrahigh-Purity A variety of face seal glands and bodies is available with controlled surface finishes, electopolished, and specially cleaned to meet ultrahigh-purity system requirements. or more information, see Swagelok Ultrahigh-Purity Process Specification (S-0). Information esignator P Metal asket ace Seal ittings 3 To order fittings manufactured according to Swagelok Ultrahigh-Purity Process Specification (S-0), add P to the ordering number. xample: 6LV-4--3-4T7P Roughness Average, R a 5 µ (0.3 µm) Side-load retainer gasket for easy installation and minimal clearance for removal Standard surface finish on glands and bodies is a roughness average of 0 µ ( µm) R a Test port at two locations for easy leak testing Markings identify manufacturer, material, and when applicable, the appropriate process designator according to Swagelok Ultrahigh- Purity Process Specification (S-0) No virtual leak zones Precision manufactured gasket for maximum performance emale threads are silver-plated to prevent galling, ensure easy assembly and consistent make-up Material heat code is stamped on glands and all shapes to ensure raw material traceability components offer the high purity of a metal-to-metal seal, providing leak-tight service from vacuum to positive pressure. The seal on a assembly is made when the gasket is compressed by two beads during the engagement of a male nut or body hex and a female nut. Minimal clearance required for removal Typical Assemblies emale nut land Side-load retainer gasket land Male nut OR emale nut land asket ody
4 Metal asket ace Seal ittings lands are for reference only and are subject to change. The dimension refers to the smallest nominal inside diameter of the part. ➀ Not designed for gasket retainer assembly. ➁ May contain internal diameter transitions. Short utt Weld 6 8 0 2 8 Nominal Wall 0.028 0.035 0.049.0.5 Nominal Wall 0.028 0.035 0.049 0.065 6 8 0 2 8.0.5 Long utt Weld, (mm) 6LV-2--3S-2T7➀ (9.) 6LV-4--3S-4T2 6LV-4--3S-4T3 0.38 (9.6) 6LV-4--3S-4T7 6LV-8--3S-4T7 6LV-8--3S-6T2 6LV-8--3S-6T7 6LV-8--3S-8T2 6LV-8--3S-8T3 6LV-8--3S-8T7, mm () 6LV-4--3S-6MT7 6LV-4--3S-8MT7 6LV-8--3S-0MT7 6LV-8--3S-2MT7 6LV-2--3S-8MT7 (9.) (9.) 0.38 (9.6) (9.) 9. () 0.06 (.5) 0.8 0.3 (7.9) (0.2) 4.0 (0.6) 6.0 (0.24) 8.0 (0.3) 0.0 (0.39) 5.0 (0.59).080 (27.4) 0.600 (5.2) 0.720 (8.3).00 (27.9).20 (28.4) 0 (5.7).20 (28.4) 0 (5.7) 0.740 (8.8).20 (28.4) 29.5 (.60) 3.0 (.220), (mm) 6LV-2--3-2T7➀ (9.) 6LV-4--3-4T2 6LV-4--3-02205 0.36 (9.) 6LV-4--3-4T3 0.38 (9.6) 6LV-4--3-4T7 6LV-8--3-4T7 6LV-8--3-6T2 6LV-8--3-6T7 6LV-8--3-8T2 6LV-8--3-8T3 6LV-8--3-8T7 6LV-2--3-2T7 6LV-6--3-6T7, mm () 6LV-4--3-6MT7 6LV-4--3-8MT7 6LV-8--3-0MT7 6LV-8--3-2MT7 6LV-2--3-8MT7 (9.) (9.) 0.38 (9.6) (9.) 9. () 0.06 (.5)➁ 0.8 0.3 (7.9) (0.2) 0.65 (6.5) (22.) 4.0 (0.6) 6.0 (0.24) 8.0 (0.3) 0.0 (0.39) 5.0 (0.59).420 (36.).200 (30.5).30 (33.3).320 (33.5).700 (43.2).800 (45.7).290 (32.8).790 (45.5).290 (32.8).40 (35.8).790 (45.5) 2.030 (5.6) 2.320 (58.9) 43.2 (.700) 45.5 (.790) 5.6 (2.030) Ni u 8500 (585) 8500 (585) 6800 (468) 500 (35) 468 (6800) 337 (4900) 24 () 23 (300) 206 () Ni u 8500 (585) 8500 (585) 6800 (468) 500 (35) (65) 468 (6800) 337 (4900) 24 () 23 (300) 206 () 500 (35) bar (psig) 468 (6800) 337 (4900) 24 () 23 (300) 206 () 500 (35) (65) bar (psig) 468 (6800) 337 (4900) 24 () 23 500 (35) 2600 (79) 372 (5400) 337 (4900) 92 () 65 () 500 (35) 2600 (79) 900 (30) 372 (5400) 337 (4900) 92 () (300) 65 206 () ()
lands Short Automatic utt Weld Metal asket ace Seal ittings 5 Nominal Wall, (mm) 36L-4--3AS 0.035 36L-8--3AS6 0.049 36L-8--3AS (9.) 0.02 (0.5) 0.03 (0.8) 0.04 (.0) 0.8 0.3 (7.9) (0.2).2 (28.4).5 (29.2).6 (29.5) 0.29 (7.4) 0.4 (0.4) 0.55 (4.0) Ni u 500 (35) 500 (35) 500 (35) 2600 (79) 6 8 0 2.0, mm () 36L-4--3-6MAS 36L-4--3-8MAS 36L-8--3-0MAS 36L-8--3-2MAS 9. () 0.5 (0.02) 0.8 (0.03).0 (0.04) 4.0 (0.6) 6.0 (0.24) 8.0 (0.3) 0.0 (0.39) 30.0 (.8) 30.2 (.9) 3.0 (.22) 30.5 (.20) 6.8 (0.27) 8.9 (0.35) 0.9 (0.43) 3.2 (0.52) 468 (6800) 337 (4900) 24 () 23 (300) bar (psig) 468 (6800) 337 (4900) 24 () 23 (300) 372 (5400) 337 (4900) 92 () 65 () Long Automatic utt Weld Nominal Wall 0.035 0.049 0.065, (mm) 36L-4--3A 36L-8--3A4 36L-8--3A6 36L-8--3A 36L-2--3A 36L-6--3A (9.) 0.96 (24.4) 0.02 (0.5) 0.03 (0.8) 0.04 (.0) 0.8 0.3 (7.9) (0.2) 0.65 (6.5) (22.).72 (43.7).82 (46.2).83 (46.5) 2.07 (52.6) 2.57 (65.3) 0.29 (7.4) 0.4 (0.4) 0.55 (4.0) 0.80 (20.3).06 (26.9) Ni u 500 (35) (65) 500 (35) (65) 500 (35) 2600 (79) (65) 900 (30) 6 2.0, mm () 36L-4--3-6MA 36L-8--3-2MA 8.5 36L-2--3-8MA 9. () 0.5 (0.02).0 (0.04) 4.0 (0.6) 0.0 (0.39) 5.0 (0.59) 43.7 (.72) 46.5 (.83) 52.6 (2.07) 6.8 (0.27) 3.2 (0.52) 9.3 (0.76) 468 (6800) 23 (300) 206 () bar (psig) 468 (6800) 372 (5400) 23 (300) 65 () 206 () Short Socket Weld Socket 0.50 (2.7) (9.) Ni u, (mm) -4--3-.50L -4--3-.75L (7.) 0.8 0.35 (8.9) 5500 (378) 5500 (378) 5500 (378)
6 Metal asket ace Seal ittings lands Socket Weld Socket, (mm) /6 ---3➀➁ 0.05 0.0 (.3) 0.70 (2.5) (7.8) -2--3➁ -4--3-6--3➂ -8--3-0--3-2--3-6--3 (7.) 0.3 (7.9) 0.38 (9.6) 0.4 (0.4) (.2) (5.7) 0.8 (7.) (0.2) 0.50 (2.7) (5.7) (22.).3 (33.3).50 (38.).56 (39.6) 2.00 (50.8) 2.22 (56.4) 0.3 (3.3) 0.20 (5.) 0.35 (8.9) 0.60 (5.2) 0.72 (8.3) 0.88 (22.4).9 (30.2) Ni u 9000 (620) 700 (489) 5500 (378) (65) 9000 (620) 700 (489) 5500 (378) (29) 7200 (496) 700 (489) 5500 (378) (65) 2200 (5) 900 (30) Reducing Socket Weld Socket, (mm) -4--3-2TSW 0.0 (2.5) -8--3-4TSW (7.) ➃.3 (33.3) 0.8.50 (38.) 0.35 (8.9) 0.60 (5.2) Ni u lind (Undrilled) land, (mm) -2--3-L➁ 0.70 (7.8) -4--3-L -8--3-L -2--3-L -6--3-L.3 (33.3).50 (38.) 2.00 (50.8) 2.22 (56.4) ➀ Uses gasket and nut. ➁ Not designed for gasket retainer assembly. ➂ Uses gasket and nut. ➃ May contain internal diameter transitions. Male Weld, (mm) -2--3-2MTW➁ -4--3-2MTW -4--3-4MTW -8--3-4MTW -8--3-6MTW -8--3-8MTW -2--3-2MTW (7.) 0.4 (0.4) 0.50 (2.7) (5.7) -6--3-6MTW 0.8 (20.6) 0.06 (.5)➃ 0.2 (3.0) (7.) (0.2) 0.53 (3.5) (9.) 0.70 (7.8).3 (33.3).50 (38.) 2.00 (50.8) 2.22 (56.4) Ni u 9000 (620) (65) 200 (77) 0 000 3700 (254) 7200 (496) (65) 900 (30)
lands Adapter Metal asket ace Seal ittings 7, (mm) -4--3-4TA -8--3-6TA -8--3-8TA 0.64 (6.2) 0.70 (7.8) 0.96 (24.4) 0.7 (4.3) 0.27 (6.8)➀ 0.37 (9.4).62 (4.0) Ni.8 (46.0).94 (49.3) 0 000 u odies Male NPT onnector ➁ are for reference only and are subject to change. The dimension refers to the smallest nominal inside diameter of the part. NPT lat, (mm) /6-2---➂ -2---2➂ -4---2-4---4-8---4-8---6-8---8-2---2-6---6 0.38 (9.6) 0.56 (4.2) (9.) 0.94 (23.9) ➀ 0.8 (0.2) 0.38 (9.6) (0.2) (5.7) (22.) 7/6 5/6 5/6.07 (27.2).3 (33.3).49 (37.8).65 (4.9).84 (46.7) 2.9 (55.6) 2.47 (62.7) Ni u 9000 (620) (65) 9000 (620) 0 000 3700 (254) 7200 (496) (65) 900 (30) L Male ulkhead onnector ➁ NPT lat lat L Panel ole Max Panel Ni u, (mm) -4--A-4M (5.7) 0.56 (4.2) -8--A-4M (9.) 0.8 (0.2) (7.) 3/6 5/6 3/6 2.2 (56.).24 2.34 (3.5) (59.4) 2/32 0.38 4370 (30) ➀ May contain internal diameter transitions. ➁ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➂ Not designed for gasket retainer assembly.
8 Metal asket ace Seal ittings odies Straight Thread O-ring Seal Male onnector ➀➁ Straight Thread Uniform O-ring Material nd lat Ni u, (mm) 9/6-8 luorocarbon 906-4---00032 0.39 (9.9) 0.8 7/8-4 luorocarbon 90-8---0076 0.50 (2.7) (0.2) (7.) 9/6-8 luorocarbon 906-8---008 0.39 (9.9) (7.).33 (33.8) 4500 (30) 0.59.66 (5.0) (42.2) 5/6.48 (7.) (37.6) 4500 (30) 4500 (30) emale NPT onnector ➀ NPT lat, (mm) /6-2--7-➂ 7/6.0 6700 6700 (27.9) (46) (46) -2--7-2➂ 9/6.9 6500 6500 (30.2) (447) (447) -4--7-2.4 0.8 (35.8) -4--7-4.54 6600 6600 (39.) (454) (454) -8--7-6 -8--7-8 -2--7-2 -6--7-6 (0.2) (5.7) (22.) 5/6 /6 5/6.76 (44.7).99 (50.5) 2.36 (59.9) 2.5 (63.8) Ni u (65) 3700 (254) 6700 (46) 6500 (447) 5200 (358) (65) 900 (30) ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ O-rings fluorocarbon KM standard, other materials available. NOT: O-rings are assembled with a silicone vacuum grease. ➂ Not designed for gasket retainer assembly. ➃ May contain internal diameter transitions. Swagelok itting onnector ➀ -4--6-200 -4--6-400 -8--6-600 -8--6-80, (mm) 0.60 0.50 (5.2) (2.7) 0.70 (7.8) 0.76 (9.3) 0.86 (2.8) 0.60 (5.2) 0.66 (6.8) 0.90 (22.9) ➃ 0.8 lat lat 7/6 9/6.53 (38.9).62 (4.) (7.)➃ /6.84 (46.7) 5/6.95 7/8 (0.2) (49.5),,, are typical finger-tight. NOT: Swagelok nuts and ferrules are provided assembled, as shown. or tubing maximum pressure ratings for use with Swagelok tube fittings, see the Swagelok Tubing ata Sheet. Ni 0 000 u
Metal asket ace Seal ittings 9 Swagelok itting ulkhead onnector ➀ -4--A-400-4--AS-400-8--A-600-8--A-80.32 (33.5) 0.60.05 (5.2) (2.67).45 (36.8).65 (4.9), (mm) 0.66 (6.8) 0.90 (22.9) 0.8 (7.) (0.2) lat lat 5/6 5/6 lat 9/6 /6 7/8 2.25 (57.2).88 (47.8) 2.54 (64.5) 2.74 (69.6),,, are typical finger-tight. NOT: Swagelok nuts and ferrules are provided assembled, as shown. or tubing maximum pressure ratings for use with Swagelok tube fittings, see the Swagelok Tubing ata Sheet. Panel ole 5/32 9/32 25/32 Max Panel 0.3 0.50 Ni u 0 000 ouble Male Union ➀ lat Ni u, (mm) -2--6-M➁ -4--6-M -8--6-M -2--6-M -6--6-M 0.8 (0.2) (5.7) (22.) 5/6 5/6.3 (28.7).55 (39.4).84 (46.7) 2.44 (62.0) 2.59 (65.8) 9000 (620) (65) 200 (77) 0 000 4 300 3 700 (254) 3 000 7200 (496) (65) 900 (30) ouble Male Reducing Union ➀ ➁ lat Ni u, (mm) -4--6-M-2-8--6-M-4 0.8 0.8 (0.2) 5/6.37 (34.8).7 (43.4) 0 000 ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assemblies. ulkhead Union ➀ lat, (mm) -4--6.30 (33.0) 0.8-4--6S 0.99 (25.) -8--6-8--6S.48 (37.6). (28.2) (0.2) lat 2.23 (56.6).82 (46.2) Panel ole 9/32 2.57 /6 /6 (65.3) 2.4 29/32 (54.4) Max Panel 0.3 0.50 0.3 Ni 0 000 u
0 Metal asket ace Seal ittings utt Weld ulkhead onnector ➀ lat Panel ole Max Panel Ni u 6LV-4--6-4T7 6LV-4--6S-4T7 (9.), (mm).30 (33.0) 0.8 0.99 (25.) 0.22 (5.6) 2.36 (59.9).95 (49.5) 9/32 0.3 500 (35) 500 (35) 500 (35) oupling -2-- -4-- lat, (mm) -8-- -2-- -6-- 7/6 /6 0.66 (6.8).9 (30.2).3 (33.3).68 (42.7) 2.04 (5.8) ouble emale Reducing Union ➀ Y, (mm) -4--6--2 0.3 (3.3) -8--6--4 lat /6.6 (29.5).4 (35.8) Y 0.36 (9.) 0.35 (8.9) Ni u 0 000 Reducing Adapter ➀ lat Y Ni u Y, (mm) -2--7-4➁ -4--7-8 0.8 /6.9 (30.2).4 (35.8) 0.69 (7.5) 0.85 (2.6) 0 000 Y ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly. Reducing ushing ➀, (mm) -4--7-2 0.3 (3.3) -8--7-4 5/6.06 (26.9).4 (35.8) 0.76 (9.3) 0.9 (23.) lat Y Ni u 0 000 4 300
Metal asket ace Seal ittings odies to Male NPT lbow ➀ NPT, (mm) -4--2-2 -4--2-4 -8--2-6 -8--2-8.07 (27.2).45 (36.8) (22.).05 (26.7).26 (32.0).45 (36.8) 0.38 (9.6) 0.56 (4.2) (9.) 0.8 (0.2) lat 3/6 Ni u 0 000 4 300 Union lbow ➀ lat Ni u, (mm) -2--9➁ 0.89 (22.6) -4--9-8--9-2--9-6--9.07 (27.2).45 (36.8).92 (48.8) 2.00 (50.8) 0.8 (0.2) (5.7) (22.) 7/6 3/6 /6 9000 (620) (65) 200 (77) 0 000 4 300 3 700 (254) 7200 (496) (65) 900 (30) Union Tee ➀ lat Ni u -2--T➁ 0.89 (22.6) -4--T -8--T -2--T -6--T, (mm).07 (27.2).45 (36.8).92 (48.8) 2.00 (50.8) 0.8 (0.2) (5.7) (22.).78 (45.2) 2.4 (54.4) 2.90 (73.7) 3.84 (97.5) 4.00 (0.6) 7/6 3/6 /6 9000 (620) (65) 200 (77) 0 000 4 300 3 700 (254) 3 000 7200 (496) (65) 900 (30) Union ross ➀ lat Ni u ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly., (mm) -2--S➁ 0.89 (22.6) -4--S.07 (27.2) -8--S.45 (36.8) -2--S.92 (48.8) -6--S 2.00 (50.8) 0.8 (0.2) (5.7) (22.).78 (45.2) 2.4 (54.4) 2.90 (73.7) 3.84 (97.5) 4.00 (0.6) 7/6 3/6 /6 9000 (620) (65) 200 (77) 0 000 4 300 3 700 (254) 3 000 7200 (496) (65) 900 (30)
2 Metal asket ace Seal ittings Welded Assemblies Male NPT onnector NPT lat, (mm) -4-W--2 0.38 0.95 7/6.58 (9.6) (24.) 0.8 (40.) -4-W--4 0.92 9/6.79 0.56 (23.4) (45.5) (4.2) -8-W--6-8-W--8 (9.).00 (25.4).0 (25.6) (0.2) /6 7/8 lat /6.89 (48.0) 2.09 (53.) Ni u emale NPT onnector NPT lat lat Ni u, (mm) -4-W-7-4 -8-W-7-6 -8-W-7-8 0.92 (23.4).06 (26.9).04 (26.4) 0.8 (0.2) 7/8 /6 /6.77 (45.0).95 (49.5) 2.8 (55.4) 6600 (454) 6600 (454) 5200 (358) Swagelok itting onnector lat lat lat Ni u -4-W-6-400 0.70 (7.8) -4-W-6-600 -8-W-6-80, (mm) 0.76 (9.3) 0.86 (2.8) 0.60 (5.2) 0.66 (6.8) 0.90 (22.9) 0.8 (0.2) 3/6 /6 9/6 /6 7/8.94 (49.3).97 (50.0) 2.23 (56.6) 6500 (447) 0 000 6 500 (447) 4 300 5200 (358),,, are typical finger-tight. NOT: Swagelok nuts and ferrules are provided assembled, as shown. or tubing maximum pressure ratings for use with Swagelok tube fittings, see the Swagelok Tubing ata Sheet. Rotating emale Union, (mm) -4-W-6-0.8-8-W-6- (0.2) lat /6.7 (43.4).84 (46.7) Ni u 0 000 4 300 emale lbow emale Tee are for reference only and are subject to change. The dimension refers to the smallest nominal inside diameter of the part..00 (25.4) 6LV-4-W-9- lbows, crosses, Micro-it fittings, and tees are available with welded male and female ends. or more information, contact your independent Swagelok sales and service representative..00 (25.4) 6LV-4-W-T-
askets Information Specify gasket material by adding the appropriate prefix designator to the basic ordering number. Material Nickel 36L stainless steel opper Prefix esignator NI U➀ xample NI-4--2-VS -4--2-VS U-4--2 NOT: Nickel and copper gasket retainer assemblies utilize a 36 stainless steel retainer. ➀ opper gaskets are unplated. owever, to order, use U as a prefix to the basic ordering number used for silver-plated gaskets. xample: U-4--2. Side-load retainer style gaskets are not available in copper. Options lind asket Metal asket ace Seal ittings 3 lind (undrilled) gaskets are available in non-retained and retainer assembly styles. To order, use -L as a suffix to the basic ordering number. xample: -4--2-VS-L NOT: lind gaskets have a maximum differential pressure rating ( P) of 00 psi (6.8 bar). Silver-Plated Non-Retained Style annot be used in a gasket retainer assembly. asket Retainer Assembly Retainer and gasket must be used as an assembly. asic, (mm) -2--2-4--2 0.22 (5.6) -8--2-0--2-2--2-6--2 (.2) 0.58 (4.7) 0.66 (6.8) 0.89 (22.6) 0.028 (0.7) asic, (mm) -4--2-R 0.24 (6.) -8--2-R -2--2-R -6--2-R (.2) 0.66 (6.8) 0.89 (22.6) 0.028 (0.7) 0.26 (6.6) 0.47 (.9) 0.78 (9.8) 0.9 (23.).4 (29.0).40 (35.6) 0.50 (2.7) 0.79 (20.).4 (29.0).40 (35.6) Unplated (VS) Non-retained Style asket Retainer Assembly Side-load Retainer Style asic, (mm) -2--2-VS -4--2-VS 0.22 (5.6) -8--2-VS -0--2-VS -2--2-VS -6--2-VS (.2) 0.58 (4.7) 0.66 (6.8) 0.89 (22.6) asic, (mm) -4--2-R-VS 0.24 (6.) -8--2-R-VS -2--2-R-VS -6--2-R-VS (.2) 0.66 (6.8) 0.89 (22.6) 0.028 (0.7) 0.028 (0.7) 0.26 (6.6) 0.47 (.9) 0.78 (9.8) 0.9 (23.).4 (29.0).40 (35.6) 0.50 (2.7) 0.79 (20.).4 (29.0).40 (35.6) asic, (mm) -4--2-Z-VS 0.24 (6.) -8--2-Z-VS (.) 0.028 (0.7) 0.45 (.4) 0.77 (9.5) escription Installation Tool Tray (nickel gaskets) Tray ( gaskets) Side-Load Installation Tool and Tray MS-4--Z-TL NI-4--2-ZT-VS -4--2-ZT-VS Tool Makes gasket handling easy, preserves cleanliness nables gasket installation where space is limited Is used to easily remove gasket from storage tray Material: polyethersulfone (PS) Tray (includes 30 gaskets) Keeps gaskets secure Keeps gaskets aligned for easy removal with sideload gasket tool leaned and packaged in accordance with Swagelok Specification S-0 Material: tray polypropylene (lid) clean polycarbonate
4 Metal asket ace Seal ittings Nuts, aps, and Plugs emale Nut lat, (mm) -2-- 7/6 0.53 (3.5) -4-- 0.8 (20.6) -8-- -2-- -6-- /6-0-- 3/6 0.88 (22.4).2 (28.4).34 (34.0) 0.2 (5.3) 0.36 (9.) 0.6 (5.5) 0.74 (8.8) 0.89 (22.6).20 (30.5) ap with Lanyard ➂ lat, (mm) -4--P-P -8--P-P Plug (.2) 0.45 (.4) /6 0.94 (23.9).0 (25.6) Lanyard Length 6 (52.4) Male Nut lat, (mm) -2--4 0.50 (2.7) -4--4➀ 0.7 (8.0) -8--4-0--4 5/6 /6 0.8 (20.6) 0.2 (5.3) 0.36 (9.) 0.6 (5.5) 0.74 (8.8), (mm) -2--P➃ -4--P➁ -8--P -2--P -6--P lat 5/6 5/6 0.68 (7.3) 0.92 (23.4).08 (27.4).43 (36.3).52 (38.6) -2--4-6--4 5/6.00 (25.4).9 (30.2) 0.89 (22.6).20 (30.5) Plug with lanyard ➂ lat Lanyard Length Short Male Nut (for use with short gland) lat, (mm) -4--P 0.92 (23.4) -8--P 5/6.08 (27.4) 6 (52.4), (mm) ap -4--4-.54N -4--4-.65N, (mm) -2--P 0.30 (7.6) 0.54 (3.7) 0.65 (6.5) lat 7/6 0.63 (6.0) 0.36 (9.) Protective ap Made of 304 stainless steel and supplied as bead protection during shipping for a variety of face seal fittings processed to Swagelok Specification S-0. 304-4--S 304-8--S 304-2--S 304-6--S -4--P (.2) 0.94 (23.9) -8--P -2--P -6--P 0.45 (.4) 0.54 (3.7) 0.63 (6.0) /6.0 (25.6).29 (32.8).54 (39.) are for reference only and are subject to change. ➀ A taper at the hex end allows the nut to move around 90 tube bends. ➁ Also available as a rotatable plug. : -4--RP. ➂ Lanyards are manufactured from 302 stainless steel material. ➃ Not designed for gasket retainer assembly.
Metal asket ace Seal ittings 5 Nuts, aps, and Plugs Split-Nut Assemblies emale A Male A Split Nut Type asic A, (mm) emale Male -4---SN -4--4-SN 0.36 (9.) 0.8 (20.6) 0.60 (5.2) 0.63 (6.0) 0.68 (7.4) igh-low onnections Type NOT: Type connections are compatible with connections and are designed for use with Swagelok high-flow diaphragm valves and gas regulators. or uniform flow, use side-load retainer style gasket. xample: NI-4--2-Z-VS. lands utt Weld Nominal Wall, (mm) Ni u 6LV-4--3-.60SR 0.4 (0.4) 0.60 (5.2) 0.035 6LV-4--3-.9SR.00 (25.4) 0.3 (7.9).9 (30.2) 6LV-4--3-.3SR.2 (28.4).3 (33.3) odies utt Weld lat Ni u, (mm) 6LV-4---6T7 (9.) (5.7) 0.3 (7.9).68 (42.7) Automatic Weld lat Ni u, (mm) 36L-4--A6 (9.) (5.7) 0.03 (0.8) 0.3 (7.9).7 (43.4) 0.4 (0.4) are for reference only and are subject to change. The dimension refers to the smallest nominal inside diameter of the part.
Metal asket ace Seal ittings 6 odies ulkhead onnector 36L-4--6-6T7 (9.), (mm).30 (33.0) 0.3 (7.9) lat lat 2.36 (59.9) Panel ole 9/32 Max Panel Ni u Union lbow lat Ni u, (mm) -4--9.07 (27.2) 0 000 Union Tee lat Ni u -4--T, (mm).07 (27.2) 2.4 (54.4) 0 000 Nuts emale lat, (mm) -4--SR 0.8 (20.6) 0.39 (9.9) Male lat, (mm) -4--4SR 0.7 (8.0) 0.39 (9.9)
7 Metal asket ace Seal ittings Lock and Tag evices These devices help prevent unintentional disassembly of connections. Additionally, both devices include a wire hole to allow for a tag to support identification and quality verification programs. itting Lock evice This device is intended for use on Swagelok metal gasket face seal assemblies with standard male and female nuts. itting Lock evice for Valve This device is intended for use on Swagelok valves with integrally machined male metal gasket face seal end connections. -4--L -4--VL -8--L -8--VL Split-Nut Installation Instructions Male emale 2 2 3
itting Installation Instructions 6 TAW 2 3 7 inger-tight TAW 4 5a 8 45 Ni 90 u 5 5b 5c Safe Product Selection When selecting a product, the total system design must be considered to ensure safe, trouble-free performance. unction, material compatibility, adequate ratings, proper installation, operation, and maintenance are the responsibilities of the system designer and user. aution: o not mix or interchange parts with those of other manufacturers. Swagelok, Split-Nut,, Micro-it TM Swagelok ompany 2002, 2003, 2004 Swagelok ompany Printed in U.S.A., MI May 2004, R6 MS-0-24