SERIES Amplifier Built-in Compact Photoelectric FX-D/A/M FX-A FX- Fiber s General Purpose Photoelectric with Full Basic Performance FZ- Compact Size Two s Mountable Together Waterproof Just mm in depth, mm shorter than a conventional model. mm mm shorter CX-9 (retroreflective type), CX- and CX- (diffuse reflective type) incorporate an automatic interference prevention function. Hence, two sensors can be mounted close together. CX-, CX-, CX- or CX-IR ( do not have this function. ) Marked Conforming to EMC Directive The sensor can be hosed down because of its IP construction and the non-corrosive stainless steel mounting bracket. EX- CX-RVM/D/NDR CX- EX- mm mm Strong Light Beam CX- (thru-beam type) emits a strong light beam which can pass through sheets of copier paper. The sensor incorporates an infrared LED that is strong against dust or dirt. sheets of copier paper Insusceptible to Extraneous Light: CX- As the spread of the beam from the CX- emitter is narrow, close mounting of sensors is possible. CX- Half the span of CX- Note: However, take care that if it is exposed to water splashes during operation, it may detect a water drop itself. Plug-in Connector Type Is Available Plug-in connector type sensor, which can be easily disconnected for replacement, is available. In case a problem occurs anyone can replace the sensor in a minute. Plug-in connector type CX--J CX- (at setting distance of mm) CX- M connector (IEC conforming) "9mm Mating cable CN-E-C (Cable length: m) CN-E-C (Cable length: m)
APPLICATIONS Detecting contents in paper pouch Detecting shiny refrigerators Detecting rubber sheet CX- CX- FX-D/A/M Detecting pet bottles ORDER GUIDE CX-IR CX-9 Transparent objects detectable with CX-IR (Typical examples) Sensing object Sensing object size Glass sheet mm t.mm "mm?mm t.mm Cylindrical glass "mm?mm t.mm Acrylic board mm t.mm Styrol (Floppy case) mm t.mm Food wrapping film mm t!m Cigarette case film mm t!m Vinyl sack mm t!m Pet bottle "mm "mm Glass bin "mm setting : to mm with the RF- reflector at the optimum condition (Note) Each object should pass across the beam at the center between the sensor and the reflector.?: Length of cylindrical glasses t : Thickness of object Note: The optimum condition is defined as the condition in which the sensitivity level is set such that the stability indicator just lights up when the object is absent. Fiber s FX-A FX- FZ- Type Appearance Sensing Model No. Sensing output Emitting element Thru-beam Narrow beam m m CX- CX- Infrared LED NPN output type PNP output type Retroreflective Thru-beam Diffuse reflective Retroreflective With polarizing filters For transparent object Long Short Narrow beam With polarizing filters For transparent object mm. to m (Note ) to,mm (Note ) mm m m. to m (Note ) to,mm (Note ) CX-9 CX-IR CX- CX- CX--PN CX--PN CX-9-PN CX-IR-PN NPN open-collector transistor PNP open-collector transistor Red LED Infrared LED Infrared LED Red LED EX- CX-RVM/D/NDR CX- Diffuse reflective Long Short mm mm CX--PN CX--PN Infrared LED EX- NOTE: Mounting bracket is not supplied with the sensor. Please select from the of optional sensor mounting brackets (five types). Note : The of the retroreflective type sensor is specified for the RF- reflector. Further, the is the possible setting for the reflector. The sensor can detect an object less than.m away (CX-IR: mm). cannot be placed in this Actual m (CX-IR:,mm) of the sensor.m (CX-IR: mm) Setting of the reflector
ORDER GUIDE Red LED type for transparent object The red LED type for transparent object, which features easy beam alignment, is available. Model No.: CX-, CX--PN (Sensing : to mm) FX-D/A/M Plug-in connector type (Not available for the self-diagnosis output type) Plug-in connector type is available. When ordering this type, add -J to the model No. (e.g.) Plug-in connector type of CX--PN is CX--PN-J. Plug-in connector type of CX-9-Y is CX-9-J-Y. Mating cable ( Nos. are required for the thru-beam type.) CN-E-C, CN-E-C CN-EL-C, CN-EL-C Type Model No. Description FX-A FX- Fiber s Straight Elbow CN-E-C CN-E-C CN-EL-C CN-EL-C Length: m Length: m Length: m Length: m.mm -core cabtyre cable with connector on one end Cable outer diameter: ".mm Self-diagnosis output type (Available with NPN output type only. However, not available for CX-, CX-, CX-IR, and plug-in connector type.) The self-diagnosis output type is available. When ordering this type, add S to the model No. (e.g.) Self-diagnosis output type of CX- is CX-S. "9mm.mm ".mm.mm mm "9mm ".mm FZ- Package without reflector CX-9, CX- and CX-IR are available without the reflector RF-. When ordering this type, add suffix -Y to the model No. (e.g.) Package without reflector of CX-9 is CX-9-Y. OPTIONS EX- CX-RVM/D/NDR CX- EX- Designation Model No. Description Round slit mask For thru-beam type sensor ( ) only Rect slit mask For thru-beam type sensor ( only ) OS-CX- (Slit size ".mm) OS-CX- (Slit size "mm) OS-CX- (Slit size "mm) OS-CX- (Slit size.mm) OS-CX- (Slit size mm) OS-CX- (Slit size mm) Sensing : mm [CX-] mm [CX-] Min. object: "mm Sensing : mm [CX-, CX-] Min. object: ".mm Sensing : 9mm [CX-] mm [CX-] Min. object: "mm Sensing : mm [CX-, CX-] Min. object: "mm Sensing : m [CX-].m [CX-] Min. object: "mm Sensing : mm [CX-, CX-] Min. object: "mm Sensing : m [CX-].m [CX-] Min. object: "mm Sensing : mm [CX-, CX-] Min. object:.mm Sensing : m [CX-] m [CX-] Min. object: "mm Sensing : m [CX-, CX-] Min. object: mm Sensing : m [CX-] m [CX-] Min. object: "mm Sensing : m [CX-, CX-] Min. object: mm Round slit mask Fitted on the front face of the sensor with onetouch. Round slit mask (Stainless steel) Rect slit mask Fitted on the front face of the sensor with onetouch. Rect slit mask (Stainless steel)
OPTIONS Designation Model No. Description For retroreflective type sensor only ( ) mounting bracket Reflective tape (For CX-9 only) RF- RF- MS-RF- MS-RF MS-RF RF- (Note ) RF- Sensing :. to m [CX-9] to mm [CX-IR] Min. object: "mm Sensing :. to.m [CX-9] to mm [CX-IR] Min. object: "mm Protective mounting bracket for RF- It protects the reflector from damage and maintains alignment. For RF- For RF- Ambient temperature: toc Ambient humidity: to % RH Notes: i) Keep the tape free from stress. If it is pressed too much, its capability may deteriorate. Notes: ii) Do not cut the tape. It will deteriorate the performance. Sensing :. to.m [CX-9] Sensing :. to.m [CX-9]. to.m [CX-IR] RF-. mm Reflective tape RF- mm.mm mm mm.mm RF-.mm RF- mm.mm mm mounting bracket MS-RF MS-RF.mm.mm FX-D/A/M Fiber s FX-A FX- mounting bracket (Note ) Universal sensor mounting stand (Note ) checker (Note ) MS-CX- MS-CX- MS-CX- MS-CX- MS-CX- MS-AJ MS-AJ-A MS-AJ-M Foot angled mounting bracket It can also be used for mounting RF-. (The thru-beam type sensor needs two brackets.) Foot biangled mounting bracket Flat mounting saves height. It can also be used for mounting RF-. (The thru-beam type sensor needs two brackets.) Protective mounting bracket It protects the sensor from damage and maintains alignment. (The thru-beam type sensor needs two brackets.) Back biangled mounting bracket Suitable for from bottom of conveyors, etc. (The thru-beam type sensor needs two brackets.) Back angled mounting bracket (The thru-beam type sensor needs two brackets.) Basic assembly Lateral arm assembly Assembly for reflector It is useful for beam alignment of thru-beam type sensors. The optimum receiver position is given by indicators, as well as, an audio signal. Notes: ) RF- cannot be used with CX-IR. Notes: ) The plug-in connector type sensor does not allow use of some sensor mounting brackets because of the protrusion of the connector. Notes: ) Refer to P.l for details of the universal sensor mounting stand. Notes: ) Refer to P.l for details of the sensor checker CHX-SC. mounting bracket MS-CX- MS-CX- MS-CX- Two M (length mm) MS-CX- CHX-SC Two M (length mm) MS-CX- Two M (length mm) MS-RF- Universal sensor mounting stand MS-AJ MS-AJ-A Elevation angle MS-AJ-M Two M (length mm) Two M (length mm) Swivel: rotation Height adjustment: mm approx. Mounting holes for M screw Swivel: rotation With the lateral arm, the sensor can sense from above a production line. rotation angle adjustment checker Two M (length mm) Swivel: rotation Height adjustment: mm approx. Mounting holes for M screw FZ- EX- CX-RVM/D/NDR CX- EX- Elevation angle Height adjustment: mm approx. checker POWER CHX-SC LEVEL Two M (length mm) Two M (length mm) Mounting holes for M screw
FX-D/A/M FX-A FX- Fiber s FZ- EX- CX-RVM/D/NDR CX- EX- SPECIFICATIONS Item Sensing Sensing object Hysteresis Repeatability (perpendicular to axis) Supply voltage Sensing output NPN output type PNP output type Utilization category Output operation Short-circuit protection Response time Operation indicator Stability indicator Power indicator Sensitivity adjuster Automatic interference prevention function Pollution degree Protection Ambient temperature Ambient humidity Ambient illuminance EMC Voltage withstandability Insulation resistance Vibration resistance Shock resistance Emitting element Material Cable Cable extension Weight Accessories Model No. Current consumption Environmental resistance Type NPN output type PNP output type Thru-beam Retroreflective Diffuse reflective Narrow beam CX- CX- CX-9 CX-IR CX- CX- CX--PN CX--PN CX-9-PN CX-IR-PN CX--PN CX--PN m m. to m (Note ) to,mm (Note ) mm (Note ) mm (Note ) "mm or more opaque object (Note ) Opaque, translucent or transparent object % or less of operation distance.mm or less.mm or less.mm or less mm or less to V DC% Ripple P-P % or less : ma or less : ma or less ma or less ma or less : ma or less : ma or less ma or less ma or less <NPN output type> NPN open-collector transistor <PNP output type> PNP open-collector transistor Maximum sink current: ma Maximum source current: ma Applied voltage: V DC or less (between output and V) Applied voltage: V DC or less (between output andv) Residual voltage:.v or less (at ma sink current).v or less (at ma sink current) Residual voltage:.v or less (at ma source current).v or less (at ma source current) DC- or DC- Switchable either Light-ON or Dark-ON Incorporated ms or less Red LED (lights up when the output is ON) Green LED (lights up under stable light received condition or stable dark condition) Red LED (lights up when the power is ON) Continuously variable adjuster (Industrial environment) IP (IEC) to C (No dew condensation or icing allowed) (Note ), Storage: to C to % RH, Storage: to % RH Sunlight:,#x at the light-receiving face, Incandescent light:,#x at the light-receiving face Emission: EN-, Immunity: EN-,V AC for one min. between all supply terminals connected together and enclosure MΩ, or more, with V DC megger between all supply terminals connected together and enclosure to Hz frequency,.mm amplitude in X, Y and Z s for two hours each m/s acceleration (G approx.) in X, Y and Z s for three times each Infrared LED (modulated) Red LED (modulated) Infrared LED (modulated) Enclosure: Polycarbonate, Lens: Polycarbonate, Indicator cover: Polycarbonate, Front cover: Polycarbonate (CX-9: Acrylic).mm -core (thru-beam type emitter: -core) oil resistant cabtyre cable, m long Extension up to total m is possible with.mm, or more, cable (thru-beam type: both emitter and receiver). : g approx., : g approx. g approx. Adjusting screwdriver: No. With polarizing filters "mm or more opaque, translucent or specular object (Note ) Incorporated Two units of sensors can be mounted closely. For transparent object "mm or more opaque, translucent or transparent object (Note ) RF- (): No. Adjusting screwdriver: No. Long Incorporated Short Two units of sensors can be mounted ( ) ( ) closely. Adjusting screwdriver: No. Notes: ) The and the object of the retroreflective type sensor are specified for the RF- reflector. Further, the is the possible setting for the reflector. The sensor can detect an object less than.m away (CX-IR: mm). Notes: ) The of the diffuse reflective type sensor is specified for white non-glossy paper (mm) as the object. Notes: ) If slit masks (optional) are fitted, an object of ".mm (using round slit mask) can be detected. Notes: ) In case the sensor is to be used at an ambient temperature ofc, or less, please contact our office. cannot be placed in this Actual m (CX-IR:,mm) of the sensor.m (CX-IR: mm) Setting of the reflector
I/O CIRCUIT AND WIRING DIAGRAMS NPN output type I/O circuit diagram circuit ZD Tr D Tr Color code/ Connector pin No. of the plug-in connector type (Brown/)V (Black/) Load Sensing output (Note ) Load ma max. (O/) ZD Self-diagnosis output (Note, ) (Blue/) V ma max. to V DC % Internal circuit Users circuit Notes: ) The emitter of the thru-beam type sensor does not incorporate the output. Notes: ) Only CX-S incorporates the self-diagnosis output. Notes: ) The plug-in connector type sensor does not incorporate the self-diagnosis output. When connecting the mating cable, the white wire is not connected. Symbols... D: Reverse supply polarity protection diode ZD, ZD: Surge absorption zener diode Tr, Tr: NPN output transistor Wiring diagram Connector pin position (Plug-in connector type) Not connected V Sensing output (Note ) V Brown Black O Blue Load Load to V DC % FX-D/A/M Fiber s FX-A FX- PNP output type I/O circuit diagram Color code/ Connector pin No. of the plug-in connector type Wiring diagram FZ- (Brown/) V circuit Tr D ZD ma max. (Black/) Sensing output (Note ) Load (Blue/) V to V DC % Brown Black (Note) Blue Load to V DC % Internal circuit Symbols... D: Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor SENSING CHARACTERISTICS (TYPICAL) All models Users circuit Notes: ) The emitter of the thru-beam type sensor does not incorporate the output. Notes: ) When connecting the mating cable to the plug-in connector type sensor, the white wire is not connected. Connector pin position (Plug-in connector type) Not connected V Sensing output (Note ) V EX- CX-RVM/D/NDR CX- Correlation between setting distance and excess gain Excess gain CX- CX- Excess gain CX- CX- CX-IR CX-9 EX-
FX-D/A/M FX-A FX- Fiber s SENSING CHARACTERISTICS (TYPICAL) CX- Thru-beam type Parallel Angular Parallel with round slit masks (".mm),,,, Parallel with round slit masks ("mm) $ L Operating angle $( ) Parallel with rect slit masks (.mm) Setting distance L (mm) Parallel with rect slit masks (mm) Parallel with round slit masks ("mm) Setting distance L (mm) Parallel with rect slit masks (mm) FZ-,, CX- Thru-beam type EX- CX-RVM/D/NDR CX- EX- Parallel Angular Parallel with round slit masks (".mm) (Down) (Up) Parallel with round slit masks ("mm).. $ L (Down) (Up) Operating angle $( ) Parallel with rect slit masks (.mm).. Setting distance L (mm) Parallel with rect slit masks (mm) Parallel with round slit masks ("mm) Setting distance L (mm) Parallel with rect slit masks (mm) (Down) (Up) (Down) (Up) (Down) (Up)
CX-9 Retroreflective type CX-IR Retroreflective type Parallel Angular Parallel Angular SENSING CHARACTERISTICS (TYPICAL) (RF-) CX- Sensing field Setting distance L (mm), mm White nonglossy paper # L (RF-) Diffuse reflective type (RF-) $ L L $ Operating angle $( ) Setting distance L (mm), (RF-) Correlation between object size and As the object size becomes smaller than the standard size (white non-glossy paper mm), the shortens, as shown in the left graph. Sensing L (mm) aamm White nonglossy paper L, ( ) Setting distance L (mm) For plotting the left graph, the sensitivity has been set such that a mm white non-glossy paper is just detectable at a distance of mm. (RF-) (RF-) $ L L $ Operating angle $( ) FX-D/A/M Fiber s FX-A FX- FZ- White non-glossy paper side length a (mm) CX- Diffuse reflective type Sensing field Setting distance L (mm) mm White nonglossy paper # L PRECAUTIONS FOR PROPER USE Correlation between object size and As the object size becomes smaller than the standard size (white non-glossy paper mm), the shortens, as shown in the left graph. Sensing L (mm) aamm White nonglossy paper White non-glossy paper side length a (mm) L ( ) For plotting the left graph, the sensitivity has been set such that a mm white non-glossy paper is just detectable at a distance of mm. Refer to P.l for general precautions. EX- CX-RVM/D/NDR CX- This product is not a safety sensor. Its use is not intended or designed to protect life and prevent body injury or property damage from dangerous parts of machinery. It is a normal object detection sensor. Mounting The tightening torque should be.nm or less. M (length mm) screw with washers MS-CX- (Optional) Operation mode switch D D L L Light-ON mode is obtained when the switch is turned fully counterclockwise. Dark-ON mode is obtained when the switch is turned fully clockwise. Others Do not use during the initial transient time (ms) after the power supply is switched on. When connecting the mating cable to the plug-in connector type sensor, the tightening torque should be.nm or less. EX-
FX-D/A/M FX-A FX- Fiber s FZ- EX- CX-RVM/D/NDR CX- PRECAUTIONS FOR PROPER USE Retroreflective type sensor with polarizing filters If a shiny object is covered or wrapped with a transparent film, such as those described below, the retroreflective type sensor with polarizing filters may not be able to detect it. In that case, follow the steps given below. Example of objects Can wrapped by clear film Aluminum sheet covered by plastic film Gold or silver color (glossy) label or wrapping paper Steps Tilt the sensor with respect to the object while fitting. Reduce the sensitivity. Increase the distance between the sensor and the object. Self-diagnosis function (Self-diagnosis output type only) The sensor diagnoses the incident light intensity, and if it is reduced due to dirt or dust, or beam misalignment, an output is generated. Sensing condition Sensing output (operation indicator) (in the Light-ON mode) Stability indicator Self-diagnosis output Insufficient beam intensity DIMENSIONS (Unit: mm) Insufficient beam interruption Stable light received level Sensing output threshold level Stable dark level ON (Lights up) OFF (Lights off) Lights up Lights off ON OFF The self-diagnosis output transistor stays in the OFF state during stable. When the output changes, if the incident light intensity does not reach the stable light received level or the stable dark level, the selfdiagnosis output becomes ON. Further, the self-diagnosis output changes state when the output changes from Light to Dark state. (It is not affected by the operation mode switch.) In case of insufficient beam interruption, there will be a time lag before the self-diagnosis output turns ON. Refer to P.l for general precautions. Retroreflective type sensor for transparent objects Optimum is possible when the position of the transparent object is set at the center of the sensor and the reflector. If the position is set near the sensor or the reflector, the may be unstable. In this case, set the position at the center of the sensor and the reflector. Transparent object When the sensor detects an uneven plastic receptacle or glass bin, the received light intensity may differ with the position or. Adjust the sensitivity after confirming the stable condition by turning the object, etc. If the object is a transparent cylinder, feed it in a position as shown in Figure A. The sensor may fail to detect an object fed in a position as shown in Figure B. Fig. A CX- CX--J Operation indicator (Red) (Note ) -M. thru-hole threads. Operation mode switch (Note ) Stability indicator (Green) (Note ) Sensitivity adjuster (Note ) Operation indicator (Red) (Note ) Stability indicator (Green) (Note ). Fig. B Operation mode switch (Note ) Sensitivity adjuster (Note ) EX- Center of. Center of... ". cable m long " -M. thru-hole threads M connector Notes: ) Not incorporated on the emitter of the thru-beam type sensor. Notes: ) It is the power indicator (red) on the emitter of the thru-beam type sensor. Notes: ) Not incorporated on the emitter of the thru-beam type sensor. Notes: ) It is the power indicator (red) on the emitter of the thru-beam type sensor.
DIMENSIONS (Unit: mm) RF- (Accessory for the retroreflective type sensor) RF- (Optional) 9. 9..... () FX-D/A/M Material: Acrylic () ABS (Base) () -". mounting holes.. Material: Acrylic () ABS (Base) -". mounting holes.. Fiber s FX-A FX- RF- (Optional) RF- Reflective tape (Optional) FZ-. ().. M nut mounting holes (for mounting at the back) Base () Effective reflecting surface Adhesive tape Material: Acrylic () ABS (Base) Two M (length mm) and two nuts RF-. -". thru-holes (for mounting at the side) -". holes deep (for mounting at the back) -M nut mounting holes (for mounting at the side) Reflective tape (Optional) (). Material: Acrylic EX- CX-RVM/D/NDR CX- () EX- Effective reflecting surface Adhesive tape Material: Acrylic 9
SENSOR SENSOR SENSOR SENSOR DIMENSIONS (Unit: mm) MS-CX- mounting bracket (Optional) FX-D/A/M FX-A FX- Fiber s t.. Material: Stainless steel (SUS) Two M (length mm) screws with washers. R.. R. -". holes (for RF-) Mounting drawing with CX- 9. Center of. R.... t. FZ- MS-CX- mounting bracket (Optional). Mounting drawing with CX-. -". holes.. (.) Center of EX- CX-RVM/D/NDR CX- t MS-CX- Material: Stainless steel (SUS) Two M (length mm) screws with washers. R.... mounting bracket (Optional) " "9 9 9.. Mounting drawing with CX- t " "9.. 9 R... EX- 9.. 9.. " R R9. Center of t. Material: Stainless steel (SUS) Two M (length mm) screws with washers t.
DIMENSIONS (Unit: mm) MS-CX- mounting bracket (Optional) t.... 9 9 R9 R Mounting drawing with CX- t. Center of FX-D/A/M R.9.9 Material: Stainless steel (SUS) Two M (length mm) screws with washers..9..9 Fiber s FX-A FX- MS-CX- t. mounting bracket (Optional) Mounting drawing with CX-. FZ-... R R Material: Stainless steel (SUS) Two M (length mm) screws with washers MS-RF-.. mounting bracket for RF- (Optional)... Center of. 9.. t.. EX- CX-RVM/D/NDR CX- " " Material: Stainless steel (SUS) Two M (length mm) screws with washers.. EX- " R. t...
FX-D/A/M DIMENSIONS (Unit: mm) MS-RF mounting bracket for RF- (Optional)... 9.. FX-A FX- Fiber s -M. thru-hole threads Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) Two M (length mm) t.. ().. () t. FZ- MS-RF mounting bracket for RF- (Optional).. ().. 9.. EX- CX-RVM/D/NDR CX- () () -M. thru-hole threads Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) Two M (length mm) t. () 9. () t EX-
DIMENSIONS (Unit: mm) MS-AJ Basic assembly (Optional) MS-AJ-M Assembly for reflector (Optional). Cable guide (POM) ()(Note) () (.). -". mounting t holes -.. oblong holes -" mounting holes Attachment (Nylon ) mounting bracket [Stainless steel (SUS)] " pipe [Stainless steel (SUS)] Base (Nylon ) -" mounting holes.. M hexagonsocket-head bolt Note: The dimensions in the brackets indicate the adjustable of the movable part. with series (Mounting part only). -M (length mm) screws with washers t Center of with RF- () (Mounting part only)... t. -M (length mm) screws with washers Two M (length mm), two M (length mm), two M (length mm), one auxiliary mounting plate for EQ- series, and one auxiliary mounting plate for EX- series.... Cable guide (POM) (.)(Note) () ( ) MS-AJ-A Attachment (Nylon ) M hexagonsocket-head bolt t " pipe [Stainless steel (SUS)] Base (Nylon ) -" mounting holes Note: The dimensions in the brackets indicate the adjustable of the movable part. with RF- () (Mounting part only). -M (length mm)... with RF- () (Mounting part only). -M (length mm). ()... Cable guide (POM) () (Note ) M hexagon-sockethead bolt. t. t... M hexagon-sockethead bolt. Lateral arm assembly (Optional). ()(Note ) () " pipe [Stainless steel (SUS)] mounting bracket [Stainless steel (SUS)] (Note ) -". mounting holes Arm joint (Nylon ) -.. " pipe oblong holes [Stainless steel (SUS)] Two M (length mm) screws with washers, and two M (length mm) screws with washers (.) FX-D/A/M Fiber s FX-A FX- FZ- EX- CX-RVM/D/NDR CX- (.) EX- -" mounting holes (.) Base (Note ) (Nylon ) Two M (length mm), two M (length mm), two M (length mm), one auxiliary mounting plate for EQ- series and one auxiliary mounting plate for EX- series Notes: ) The dimensions in the brackets indicate the adjustable of the movable part. Notes: ) Refer to MS-AJ (basic assembly) for the assembly diagram with the base, sensor mounting bracket, sensor or reflector.