TONNEAU INSTALLATION GUIDE

Similar documents
TONNEAU INSTALLATION GUIDE

TONNEAU INSTALLATION GUIDE

TONNEAU INSTALLATION GUIDE

TONNEAU INSTALLATION GUIDE

TONNEAU INSTALLATION GUIDE

TONNEAU INSTALLATION GUIDE

Installation Instructions Table of Contents

Make sure the rail is clamped square as shown. Start at the front, and place the first clamp approx 6 to 9 inches back.

Installation Instructions

NIS NAV AM (MY15 >) - Aluminium Tonneau Cover ATC0051 (silver) ATC0052 (Black) Installation Time: Approx. 60 Minutes WARNING!

C15C C15C. Page 1 of 20

PARTS LIST: Components. ` Bi-Fold Tonneau Cover

INSTALLATION INSTRUCTIONS

James Barone Racing Aftermarket Parts and Accessories

INSTALLATION SHEET. PARTS INCLUDED IN YOUR KIT 1 Pair rails (L&R) Roll top assembly Bulkhead seals (1x 1/4 & 1x 3/4 thick) (1x 1/4 & 1x 1/4 thick)

INSTALLATION INSTRUCTIONS

INSTALLATION / OPERATING INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH

ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH

** DO NOT EXCEED THE RECOMMENDED VEHICLE TOWING WEIGHT RATING ** DODGE RAM 1500

INSTALLATION INSTRUCTIONS

RAM BOX INSTALLATION SHEET

INSTALLATION INSTRUCTIONS

SPECIAL INSTALLATION INSTRUCTIONS

INSTALLATION SHEET. PARTS INCLUDED IN YOUR KIT 1 Pair rails (L&R) Roll top assembly Bulkhead seals (1x 1/4 & 1x 3/4 thick) (1x 1/4 & 1x 1/4 thick)

Place these instructions in vehicle s glove box after installation is complete. Clean Tonneau Cover with a mild detergent and water solution.

DF Ford F Short Bed 2009-Current

Stowe Cargo Management System

07 & UP GM 1500 PICKUP 2.0 FRONT 1.0 REAR LEVELING KIT INSTALLATION

STOP---READ THIS FIRST!

Installation Guide Current Ford F-250 & Ford F-350 Super Duty. Product Code: 109 & 119

INSTALLATION INSTRUCTIONS

RAMPAGE POWER LIFT RAMP

Installation Guide. Stowe Cargo Management System. Table of Contents

1-3/8 Designer Metals Telescoping Traversing Rod Installation Instructions

RIGID SERIES REAR BUMPER RB-F-100-JK, RB-F-101-JK, RB-F-102-JK, RB-F-103-JK RB-F-100-JKA, RB-F-101-JKA, RB-F-102-JKA, RB-F-103-JKA

Fog Lamp Instructions

HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX

B4578BTPA Fender Mounting Instructions for MIN4000, MIN900, MIN1500 & MIN1554 Fenders

MISSING PARTS? call Extang at

TOYOTA FJ CRUISER 6 SUSPENSION KIT

HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX

SERIES A & AA ROLLER DOORS INSTALLATION GUIDE

D40C HINGE # x Support Plate x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws

J&M CASTER/CAMBER PLATE INSTALLATION INSTRUCTIONS (#24213) Hardware:

INSTALLATION INSTRUCTIONS AND OWNER S MANUAL

HARD FOLDING TONNEAU COVER INSTALLATION GUIDE

INSTALLATION INSTRUCTIONS

Installation Guide 4097M

Installation Instructions

FOR INSTALLATION ON DRIVER'S SIDE ONLY

Shur-Co. Owners & Installation Manual. READ INSTRUCTIONS - Failure to assemble cover properly will void warranty.

Marlon Xplore II / Xplore Pro II Deck Installation & Assembly Instructions

Fast Master Products, Inc. P.O. Box 654, Katy Texas Tel: (281) Fax: (281)

INSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK

100mm. Part# AA Rev CUSTOMER SUPPORT: Wash truck bed.

Haul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.

INSTALLATION GUIDE DODGE PRODUCT CODE:

INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067

CAUTION. INSTALLATION INSTRUCTIONS Part Number Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck

96-06 TOYOTA TUNDRA & TOYOTA TACOMA FRONT 2.0 LEVELING KIT INSTALLATION

Please read these Installation Instructions in their entirety prior to installing or operating this equipment.

Installation Guide 4099H

4" Oval Nerf Bar. Part No. A1003S/B. PARTS LIST: Qty Part Description Qty Part Description

H15P. Toyota Hilux A-DECK Dual Cab

INSTALLATION SHEET. TOOLS RECOMMENDED 9/16 Wrench or socket 7/8 Drill bit & drill (optional)

HiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black

2015 COLORADO 1 /2 LEVELING KITS

2016 & Up Miata MX-5 Coilover Installation Instructions

2016 Toyota Tacoma INSTALLATION SHEET

Peg-Harness installation instructions

MKVI Jetta Fog Light Kit

B100PBA Fender Mounting Instructions for MIN100, MIN150, MIN1600, MIN1900, MIN2200, MIN221800, MIN2260, MIN2480 & MIN9950 Fenders

INSTALLATION GUIDE STANDARD PRODUCT CODES:

Installing a genuine HoodLift on a Jeep JK with an AEV hood

INSTALLATION INSTRUCTIONS

Installation Instructions Mustang Air Suspension. Part # Mustang Air Suspension System.

MODEL 2604 WARNING <THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> Custom 5th Wheel Hitch Mounting Rail Installation Instructions

RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS.

ECO-SERIES FRONT BUMPER FOR GM SIERRA #GM-19337

HURST COMP STICK KIT 2008 and up DODGE CHALLENGER (with AUTO-STICK) Catalog # &

(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers

Front HD Bumper. Part No. FHDB003TI. PARTS LIST: Qty Part Description Qty Part Description

INSTALLATION INSTRUCTIONS

SUT-450-I ASSEMBLY REQUIREMENTS

TrailGator REAR BUMPER INSTALLATION INSTRUCTIONS Runner

INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D

Installation Instructions

2010 to 2013 Toyota 4runner Rear bumper installation instructions:

Folding Golding. Precision High Speed Travel Wheel

Steeda Sport Mustang Lowering Springs (2005+) - Installation Instructions

Installation Instructions

#4011 Standard PRO Installation Instructions

Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D

Current Range Rover Sport STRUT Collection Installation Manual

63162K 2015 Chevrolet Colorado 4WD Leveling Kit w/ 1 Rear Lift Kit

M14 AUTOMOTIVE SPARK PLUGS AND WIRES CONVERSION KIT INSTALLATION INSTRUCTIONS

PRP Seats 570/800/900 RZR 4 Doors

Owners & Installation Manual. Read Instructions - Failure to assemble cover properly will void warranty.

INSTALLATION INSTRUCTIONS

Transcription:

TONNEAU INSTALLATION GUIDE Warranty, Care & Maintenance Model 1080 GMC Sierra Ext/Crew Cab 5.7' Short Bed 2007-Current EASY AS 1-2-3! NORMAL INSTALLATION TIME 30 MINUTES For Warranty Issues, Contact UnderCover Directly (866) 900-8800 www.undercoverinfo.com

Page 1 1 2 3 Be sure to use only cleaners, waxes, etc., which are labeled Safe for Plastics. Make sure that chemicals or substances, which are not labeled safe for plastics, do not come in contact with your Undercover. Failure to do so could cause discoloration and/or structural damage to your Undercover and will void your warranty. Paint rubbing of the truck is normally not a problem, but is always a possibility with any tonneau. To ensure less chance of possible paint rubbing of the truck, it is suggested to install a tailgate protector and adhere Cab Skin, Scotch Cal, or similar product to the truck bed. These products can provide added assurance against paint rubbing. Undercover Tonneaus are designed from trucks that do not have a bed liner (spray-in bed liners pose no problem). Trucks that do have under-the-rail or over-the-rail bed liners will require some minor trimming of the bed liner to ensure proper placement of the mounting brackets. Due to the wide variety of bed liner manufacturers, the modifications will vary slightly between different brands. Any modifications must be made to the bed liner and NOT to the Undercover mounting hardware. Modifications to the mounting hardware will result in improper installation and will void your warranty. Note: If your truck is equiped with a spoiler style tailgate piece, you will need to replace it with a standard smooth style tailgate piece like the photo below.

Page 2 Note: If your Tonneau has already been installed, skip to Page 11 for removal and reinstallation instructions.

Page 3 A B C FACT: Undercover is the lightest hardshell tonneau in the industry. Only 58-pounds for full size trucks. Place the rear bracket according to the measurements on Page 4, Figure 1, Pictures A & B. Use two of the holes in rear bracket which are unobstructed by the truck bed, (there will be four to choose from), one hole as far forward as possible and one hole as far back as possible (this will vary depending upon truck model) Page 4, Figure 2. Place a 5/16 x 1 1/4 bolt with a 5/16 lock washer and a 5/16 washer through the hole in bracket Page 4, Figure 3. Place clamp on backside of bracket behind the bed lip of the truck. Thread the bolt into the clamp and tighten being careful to not let the clamp twist while tightening. Make sure bracket is held down tightly against truck bed rail before tightening. Repeat procedure for second clamp. Mounting bracket bolts must be tightened down without bending the bracket. Keep the clamps straight and do not let them turn while tightening Page 4, Figure 3, Picture C & D. D WARNING! Do not over tighten and distort the brackets. Bolts must be checked for tightness periodically. Failure to do so could cause serious damage to both the truck and / or your UnderCover. Repeat Steps A through C for opposite side of the truck bed. Footnote: The bolts should be tightened securely, stop tightening at the first sign of the bracket distorting.

Page 4 43" GMC Sierra 5.7' Short Bed 2007-Current. Proper position for Bolt Screws and Clamps.

Page 5 FACT: Undercover s ABS-Composite material makes it the strongest and most durable tonneau on the market. A Install your front mounting bracket using the measurements on Page 6, Figure 4. Using a tape measure place the rear end of the front bracket 15 3/4" from the inside wall of the bulkhead. Follow the same steps on the opposite side. B Now using C clamps provided place 5/16 x 1 1/4 bolt with 5/16 lock washer and 5/16 washer through the hole in the front bracket and thread in the C clamp as shown on Page 6, Picture A. Each side will require 2 clamps. Do not completely tighten down the clamps at this point, rather insure that they are secure using a ½ socket or wrench. You may need to make some slight adjustments once the cover is in place in order to line up the cover with the bed and avoid rubbing. After you have test fit the cover and feel that the brackets do not require any further adjustment you should then tighten down front bracket clamps to the proper tightness (See footnote below). On Page 8 you can find instructions as to how best to test fit your cover and how to make any adjustments to your front brackets (if necessary). C You are now ready to install your cover and test for proper fit with the bed rails of your truck. Mounted to your covers are both a left and right 4 bar hinge. See Page 6, Figure 5, Picture B. With some assistance, lift the cover up and over the bed bringing the 4 bar hinges over the front brackets see Page 6, Figure 5, Picture C. Your front brackets have 2 mounting posts, see Page 6, Figure 5, Picture D. The 4 bar hinges attached to your cover have 2 slots on each that slide over the mounting post fixed to the bracket on your truck. Set the cover down sliding the slots over the post on both sides. See Page 6, Figure 6, Picture E. D The cover should be resting on the bed rail of your truck with a larger than normal overhang at the tail gate. See Page 7, Picture F. From the rear of the truck you should now be able to push the cover forward sliding the mounting post into the slots of the 4 bar hinge. See Page 7, Picture G. Your cover should now be locked into place and your are ready to tighten the twist knobs on the 4 bar hinge into the front brackets. Only hand tighten this and secure as much as possible. See Page 7, Picture H. You may need to remove the cover to make adjustments to the front bracket to line up the cover with the bed. Footnote: The bolts should be tightened securely, stop tightening at the first sign of the bracket distorting.

Page 6 15 3/4" MARKS LINE UP WITH SLOTS ON HINGE

Page 7

Page 8 The measurements given for the front brackets on step 2 are just a starting point. These measurements will work for a large percentage of trucks. Unfortunately not all truck beds are assembled 100% square, so some adjustments may be necessary. With your cover closed, take a quick inspection to make sure that it is not touching the bed on either side or the tailgate. If it appears square or close to square go on to Step 3, pages 9 and 10. If it is making contact with the side of the truck or the tailgate, you may wish to make some adjustments before going to the final step. To adjust the cover front to back evenly, move both of the front brackets forward or backward accordingly. To adjust one side or the other, move the front brackets forward or backward independently. Any questions you can call tech assistance Monday through Friday, 8 a.m. 5 p.m. Central Time (866) 900-8800. Very Important: Periodically check your truck for rubbing. Make slight adjustments when necessary.

Page 9 A FACT: In less than one minute, you can both take on and off the Undercover tonneau. Fastest removal system in the industry. Install hydraulic struts making sure LARGE end of strut is attached to the tonneau, and SMALL or rod end is attached to the ball stud on rear bracket Page 10, Figure 7, Picture A. B Be sure that the front flap seal hangs over the bulkhead of the truck and is not rolled under the tonneau after installation. If flap seal is rolled under the tonneau, open the tonneau, and from the inside push the flap seal out from under the tonneau and over the bulkhead Page 10, Figure 8, Picture B. C Close tonneau and check length on the truck. There should be 1/8 -to- 3/8 gap between the tailgate and the tonneau. If this is not correct, adjust by moving front brackets forward or backward to achieve correct length. Front brackets may also have to be adjusted independently to square-up tonneau on some truck beds. D Adjust lock strikes Page 10, Figure 9, Picture C. When adjusted properly you should be able to turn the key to the locked position without having to push down on the tonneau. There should be a very slight amount of play between the lock cam and lock strike. A good rule of thumb is to adjust the lock to have approximately 1/8 gap between the cam and lock strike with the truck tailgate down. This usually gives you the proper adjustment after the tailgate is shut Page 10, Figure 9, Picture D. WARNING: It is very important to be able to turn the key without any resistance. Do not try to force the lock cam to turn if you encounter resistance. This could result in a broken key or broken lock. Adjustment may be necessary to the lock strike plate to achieve a smooth turn without any resistance.

Page 10

Page 11 Congratulations! Your 30-minute installation job is now complete. Now, in less than one minute, you will be able to put on and take off your tonneau cover. STEP 1 Release strut off of ball stud Picture B. Holding tonneau up with one hand, place loose end of strut on storage clip Picture C. Repeat for the other side. STEP 2 Turn twist knobs until they release Picture A. STEP 3 Go to the rear of the truck and pull Tonneau cover back, releasing the post from the hinge slot, Picture D. You are now ready to lift the cover off. STEP 1 Place tonneau on the truck and follow instructions on Page 7. STEP 2 Be sure that the front flap seal is hanging over the bulkhead and not rolled under, see Picture E on this page. STEP 3 Reinstall struts as seen in pictures Pictures F and G on this page.

Page 12 STEP 1 Prior to removing the tonneau, mount the two J-Hooks provided on the garage wall. The hooks must have a minimum height from the floor of 84", and be 32 on center horizontally apart Picture A & B. STEP 2 Remove your tonneau from the truck bed according to instructions on Page 11. STEP 3 Hang tonneau vertically on the wall-mounted J-Hooks, with the underside against the wall inserting J-Hooks into the holes provided in Picture C & D.

Page 13

Page 14

TONNEAU INSTALLATION GUIDE Page 15 THANK YOU! Congratulations! You ve just installed the fastest-selling, highest-quality tonneau in the industry. Thank you very much for your purchase of UnderCover! David Wells President UnderCover, Inc. UnderCover, Inc. P.O. Box 620 Rogersville, MO 65742 (417) 753-8000 (866) 900-8800 www.undercoverinfo.com sales@undercoverinfo.com For any Warranty issues, contact UnderCover directly. 2010 UnderCover, Inc. All rights reserved.