Accessory Application Publication No. INSTALLATION INSTRUCTIONS HOMELINK P/N 08U77-MKC-A00 GL1800/B/BD/D/DA Honda Dealer: Please give a copy of these instructions to your customer. MII 16426 Issue Date January 2018 PARTS LIST (3) INSTALLATION CAUTION To prevent burns, allow the engine, exhaust system, radiator, etc., to cool before installing the accessory. NOTE: (4) Disconnect the negative (-) cable from the battery before installing this accessory. (5) HOMELINK 1 KNOB The memory of the clock will be erased when you disconnect the battery. Reset the clock after reconnecting the battery. (2) (1) HOMELINK 2 KNOB Reinstall the removed parts on the motorcycle and make sure that the wires and harnesses are not pinched. Although the illustration is of GL1800/D/DA, use the same procedures for other models. 1. Open the left saddlebag lid as shown. Repeat on the right side. No. Description Qty (1) Installation instructions URL 1 (2) Homelink unit 1 (3) Sub harness 1 (4) Homelink knob set 1 (5) 4 mm screw 2 TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Dish soap solution (Water:Dish soap / 100:1) Shop towel Torque wrench TORQUE CHART Tighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts. LEFT SADDLEBAG LID 2. Remove the left side cover as shown, and disconnect the negative (-) cable of the battery. Item N m kgf m Ibf ft 4 mm screw 1 0.1 0.7 2018 American Honda Motor Co., Inc. - All Rights Reserved. 1 of 12 LEFT SIDE COVER 87959-MKC-A000
3. Remove the right side cover in the same manner as the left side. 4. Remove the seat as shown. Disconnect the connector for GL1800/D/DA. 6. Remove the parts as shown. Perform this step on GL1800B/BD only. SEAT BOLT WASHER CENTER REAR TOP COVER 7. Remove the center rear top cover as shown. Perform this step on GL1800B/BD only. CENTER REAR TOP COVER 5. Remove the right and left rear top lid as shown. Perform this step on GL1800B/BD only. RIGHT REAR TOP LID LEFT REAR TOP LID 2 of 12
8. Remove the right and left passenger grip as shown. WASHER RIGHT PASSENGER GRIP BOLT LEFT PASSENGER GRIP Remove the cable. 10. Fold down the left rear view mirror backward as shown. LEFT REAR VIEW MIRROR CABLE 9. Remove the right pillion step holder cover as shown. <Right side> 11. Remove the left mirror arm panel as shown. LEFT MIRROR ARM PANEL BOLT 12. Remove the left rear view mirror as shown. LEFT REAR VIEW MIRROR Disconnect the connector. RIGHT PILLION STEP HOLDER COVER BOLT 13. Remove the right mirror arm panel and right rear view mirror in the same manner as the left side. 3 of 12
14. Remove the screw as shown. Repeat on the right side. 17. Remove the left inner cowl as shown. LEFT INNER COWL 15. Remove the left deflector panel as shown. 18. Remove the clip as shown. LEFT DEFLECTOR PANEL 19. Remove the left middle cowl as shown. 16. Remove the clip as shown. LEFT MIDDLE COWL 4 of 12 20. Remove the right deflector panel, right inner cowl and right middle cowl in the same manner as the left side.
21. Remove the parts as shown. Repeat on the right side. COLLAR 24. Remove the right outer air guide as shown. RIGHT OUTER AIR GUIDE 22. Remove the 2P black connector as shown. <Right side> 2-PIN WATERPROOF CONNECTOR (Black) 25. Remove the pocket cable as shown. 23. Remove the clip and disconnect the connector as shown. 2-PIN WATERPROOF CONNECTOR (Black) POCKET CABLE 5 of 12
26. Remove the parts as shown. 28. Remove the center switch panel as shown. CENTER SWITCH PANEL Disconnect the connector. 27. Remove the shelter as shown. SHELTER 29. Remove the right and left center console panel as shown. LEFT CENTER CONSOLE PANEL RIGHT CENTER CONSOLE PANEL CENTER SWITCH PANEL (Back side) 6 of 12
30. Remove the center console garnish as shown. 32. Install the Homelink knobs as shown. HOMELINK 2 KNOB HOMELINK 1 KNOB CENTER CONSOLE GARNISH CENTER SWITCH PANEL CENTER SWITCH PANEL 31. Remove the dummy switch as shown. DUMMY SWITCH (Save) (Save) 33. Install the center console garnish, right and left center console panel in the reverse order of removal. 34. Install the center switch panel in the reverse order of removal. 35. Open the rear trunk lid as shown. Refer to the Owner s Manual and using an emergency trunk cable to open the rear trunk lid. REAR TRUNK LID CENTER SWITCH PANEL 7 of 12
36. Remove the USB cord as shown. Perform this step on GL1800DA only. 39. Remove the parts as shown. Repeat on the left side. USB CORD 37. Remove the parts as shown. <GL1800DA> TRUNK HOLDER 40. Remove the trunk right side cover as shown. Repeat on the left side. <Right side> TRUNK RIGHT SIDE COVER 38. Remove the trunk front lower panel as shown. TRUNK FRONT LOWER PANEL 8 of 12
41. Remove the clips as shown. Repeat on the right side. GL1800/D/DA 43. Remove the rear fender as shown. GL1800B/BD REAR FENDER Disconnect the connector. 44. Remove the saddlebag rear center cowl as shown. SADDLEBAG REAR CENTER COWL 42. Disconnect the 2P black connector and remove the trunk center lower cover as shown. 2-PIN WATERPROOF CONNECTOR (Black) TRUNK CENTER LOWER COVER 9 of 12
45. Remove the parts as shown. <Right side> BOLT WASHER 47. Move the right saddlebag catch as shown. RIGHT SADDLEBAG CATCH 48. Remove the radio antenna as shown. 46. Remove the screws as shown. RADIO ANTENNA RIGHT SADDLEBAG CATCH 10 of 12
49. Remove the emergency trunk cable as shown. 52. Apply dish soap solution to the grommet at the position shown. EMERGENCY TRUNK CABLE DISH SOAP SOLUTION Apply. GROMMET SUB HARNESS RIGHT SADDLEBAG CATCH 50. Remove the plug as shown. 53. Move the right saddlebag and route the sub harness as shown. SUB HARNESS PLUG (Save) BOOT Move. 51. Install the Homelink unit as shown. HOMELINK UNIT 4 mm SUB HARNESS GROMMET Insert into the hole. RIGHT SADDLEBAG CATCH 11 of 12
54. Connect the sub harness to the Homelink unit as shown. SUB HARNESS 57. Route and connect the sub harness as shown. SUB HARNESS HOMELINK UNIT 55. Install the right saddlebag, emergency trunk cable and right saddlebag catch in the reverse order of removal. 56. Remove the dummy connector as shown. 8-PIN WATERPROOF CONNECTOR (Gray) 58. Install the motorcycle s parts in the reverse order of removal. Confirm that any wire harness is not caught or too tight. 59. Check the Homelink, headlight and the other lights for proper operation. MOTORCYCLE S HARNESS 8-PIN WATERPROOF DUMMY CONNECTOR (Gray) (Save) 12 of 12