VIEW A A A 55 MJH 04-24-.XX 0.00.XXXX 0.00 OF 00-00994-A
22 2 5 5 8 7 8 8 5 7 25 8 8 9 2 9 0 28 2 0 20 ITEM NO. NOTES PART NUMBER QTY. 00-0289 MUD FLAP BRACKET 2 2 20-00095 BRAKE LINE 20-00049 FENDER 2 4 207-0004 TILT PIN 5 20-00028.50"- X.0" X.50" U-BOLT 8 20-0000.50"- X.0" X 5.25" U-BOLT 2 7 20-0004.25"-8 NYLOCK HEX NUT 2 8 20-000.50"- CENTERLOCK HEX NUT 20 9 20-0008.48"-4 X 2.25" X 5." U-BOLT 4 0 20-00084.25"-20 X.75" HX HD BOLT 0 20-00085.25"-20 CENTER LOCK NUT 2 20-00092.25"-20 REG. HEX NUT 4 20-007.25" SPLIT LOCK WASHER 4 4 20-007.50"-20 X.8" LUG NUT 0 5 20-0057.5"-2 NYLOCK HEX NUT 4 20-002.5"-2 X.25" HX HD BOLT 4 7 20-00240.50" SAE FLAT WASHER ZINC 4 8 20-002.25"-8 X.50" HX HD BOLT 2 9 20-000.48"-4 CENTERLOCK HEX NUT 8 20 20-0040.250"-20 NYLOCK HEX NUT 8 2 20-0084 SCREW LOBE TRUSS HD /4"-20 X -/2" 8 22 20-0048.25"- X 5.75" HX HD BOLT 2 20-00420.25" FLAT WASHER 2 24 20-0042.25"- TOP LOCK HEX NUT 25 2-0009 KEEL ROLLER 2 2 220-0004 5-HOLE TIRE & RIM 2 27 229-00095 BUSHING 2 28 229-004 MUD FLAP 2 29 24-00058 LOGO 4 0 24-0000 LOGO 2 00-0900 SPRING HANGER WELDMENT 2 2 00-0297 FRAME WELDMENT 0-094 WINCH ASSY 4 0-0224 AXLE ASSEMBLY 5 0-0292 ROLLER ASSY 2 0-008 ROLLER ASSY 2 7 0-0209 TONGUE ASSY SWING X4 BRK 8 LIT-0047 SERIAL TAG ALUM. AUS 4 29 0 7 2 4 27 2 24 5 NOTE:.) SEE ADDITIONAL INSTRUCTIONS ON PAGE SIX. A 55 MJH 04-24- 4.XX 0.00.XXXX 0.00 2 OF 00-00994-A
VIEW B GREEN/WHITE WIRES CONNECT TO THE REAR HARNESS DOWN THE LEFT SIDE TUBE THE TAIL LIGHT IS MOUNTED TO THE CENTER HOLES OF THE TAIL LIGHT BRACKET. YELLOW/WHITE WIRES CONNECT TO THE REAR HARNESS DOWN THE LEFT SIDE TUBE WIRE CLIPS BRAKE LINE BRAKE LINE PIGTAIL THE TAIL LIGHT IS MOUNTED TO THE CENTER HOLES OF THE TAIL LIGHT BRACKET. WIRE CLIPS THE LOOM IS PLACED AROUND THE WIRE HARNESS. CABLE TIES (2-0004) TO BE FASTENED AROUND THE LOOM (X). B THE LOOM IS PLACED AROUND THE WIRE HARNESS AND BRAKE LINE AT THE SWING JOINT AREA. CABLE TIES (2-0004) TO BE FASTENED AROUND THE LOOM (X). A 55 MJH 04-24- DWG. REV. ECR/NDR NUMBER REVISED BY DATE BLUE WIRE RUNS UP TO THE ACTUATOR SOLENOID.XX 0.00.XXXX 0.00 OF 00-00994-A
DIMENSIONS "B" "C" "D" "E" "P" Model # POST UP REF AXLE LOGO * 5.0 5.5 87.0 5.25 4.5 * SEE JOB PART NUMBER FOR WHICH TRAILER SETUP TO USE D TRAILER CHECK LIST 0 FT. LBS. - 4X C.25 05.7 9.4 B 0 FT. LBS. - 8X 2 22.8 P 0 FT. LBS. - 4X E 80 FT. LBS. - 0X 28. 9. 24.2 209.9 SWUNG 25. (0 FT. LBS. - X) 4.4 NOTES: 2 DIMENSION IS FROM BACK OF SPRING HANGER TO THE BACK OF THE FRAME. A 55 MJH 04-24-.XX 0.00.XXXX 0.00 4 OF 00-00994-A
Dimensions "F" "G" "S" Model # FRONT REAR STAMP * 7.0 7.0 8.9 * SEE JOB PART NUMBER FOR WHICH TRAILER SETUP TO USE 79.0 4.0 4. 4.4 C 74.5 95.7 VIEW C.0 S LIT-0047 F G NOTES: ROLLER LOCATION IS THE DISTANCE FROM THE INSIDE OF THE SIDE TUBE TO THE OUTSIDE EDGE OF THE ROLLER BRACKET. A 55 MJH 04-24-.XX 0.00.XXXX 0.00 5 OF 00-00994-A
VIEW MUD FLAP MOUNTING INSTRUCTIONS 2 VIEW 2 ROLLER MOUNTING INSTRUCTIONS ROLLER GUIDE VIEW ROLLER MOUNT TILTED DOWN (SHOWN): WINCH STRAP WITH HOOK RUNS UNDER THE ROLLER GUIDE BEFORE BEING ATTACHED TO THE BOW EYE OF THE BOAT. MOUNT TILTED UP: WINCH STRAP SHOULD BE RUN UNDER THE ROLLER & OVER THE ROLLER GUIDE BEFORE BEING ATTACHED TO THE BOW EYE OF THE BOAT. REAR CROSS MEMBER A 55 MJH DWG. ECR/NDR REVISED 04-24- DATE.XX 0.00.XXXX 0.00 OF 00-00994-A