NEW High speed transmission, mm pitch Small Interface Connector DH Series Overview DH Series is an impedance controlled interface connector for high speed transmission. mm contact mating pitch together with a mm mounting pitch yields a more compact, lower profile, higher density alternate to conventional half pich interface connectors. 4 different lock styles are available to meet various applications. Screw Lock Type (Locked with screwdriver) Screw Lock Type (Hand-screw) One Touch Lock Type (Metal Button) One Touch Lock Type (Plastic Button) Features. Small Design Mating face area Approx 50% reduced DXM Series (Conventional general purpose half pitch type) DH Series 37.6(6 3.6(6 pos.) 30(7 pos.) Mounting pitch: mm SMT 9.3 4.8 Mating pitch:.7mm Mating pitch:.0mm 8. Robust design Receptacle Robust design resists wrenching D-shaped opening. Plug PCB Retention Force Through hole mounting for shell and metal fitting increases PCB retention force. Secure Panel Attachment (optional) with easy to use hexagon sockets. M screw Robust & Secure Screw Lock Tightening torque:0.06 to 0.07 N m max 00.9
3. Excellent Shielding for EMI Privention Grounding Structure Panel PCB Metal Shielding Common component used for both top and bottom shielding /Easy assembly 4. Wide variation There are various variations corresponding to the usage. Lock variation Lock type Cover case receptacle Item Specification /Part number Item Connector DH60-**P / DH80-**P Part number Screw lock Screwdriver type DH-**-CVB Hand-screw type DH-**-CVB Panel lock Applicable panel thickness(mm).4 to.6 0.9 to. to 0.8mm No panel Number of washers 0 (t=0.4) (t=0.6) (t=0.8) Part No. DH-LNA DH-LNA-W4 DH-LNA-W8 DH-LNA-W6 Metal button One touch lock DH-**-CTB Plastic button Connector DH-**-CTB *Screw lock type and One touch lock type does not mate together. DH60A-**P / DH80A-**P Common part Lock type Item Screw lock One touch lock Connector Specification / Part number Plug IDC type Cable spec. Outer dia. Construction Twinax cable 0.88 to 0.9 7/0.7 Twisted pair cable 0.64 to 0.68 (AWG#8) solder type DH40-**S (Developing Pin-variation of the above item is under planning. Please consult HRS sales.) *The figure in ( ) clamp part number is equal to the cable's outer diameter. Part No. DH30B-**S DH3B-**S Clamp metal No. of pos. Part No. 7 DH-7-CMB(6.3) 7 DH-7-CMB(6.9) DH-7-CMB(7.3) 37 DH-37-CMB(8.8) 5 DH-5-CMB(9.6)
5. High Speed Data Transmission This data is for reference only. The data can differ due to cable or PCB used in evaluation. Eye Diagram [CH-CH] 500Mbps (Cable:0m) Gbps (Cable:5m).5Gbps (Cable:m) Measurement Condition Pin Assignment Pair B G-S-S-G G:ground S:Signal Pair A G-S-S-G Pair A Pair B Measurement Condition Measurement Pair:Deferential Pair A Cable:Twinax cable Input signal voltage:500mv Pulse Pattern Generator Oscilloscope Cable length 3
Specifications Ratings Item.Contact resistance.insulation resistance 3.Withstanding voltage 4.Insertion and with drawal forces 5.Durability 6.Vibration 7.Shock 8.Temperature cycle 9.Humidity (Steady state) 0.Salt spray test Screw lock type receptacle connector (DH60-**P / DH80-**P) One Touch Lock Type Receptacl connector (DH60A-**P / DH80A-**P) Plug connector (DH3*B-**S) Screw lock type cover case (DH-**-CVB) Lock type cover case (DH-**-CVB) One Touch Lock Type metal button cover case (DH-**-CTB) One Touch Lock Type plastic button cover case (DH-**-CTB) Lock screw (DH-LNA***) Current rating Voltage rating Metal clamp(dh-cmb(**)) A 5 V AC Specification 50mø max.(signal) 000Mø min. No flashover or insulation breakdown ➀Contact resistance:70mø max. ➁No damage, cracks or parts dislocation. ➀No electrical discontinuity of 0µs or longer. ➁No damage, cracks or parts dislocation. ➀Contact resistance:70mø max. ➁No damage, cracks or parts dislocation. ➀Insulation resistance:00mømin. ➁No damage, cracks or parts dislocation. ➀Contact resistance:00mø max. Operating temperature range Storage temperature range Conditions 00mA(DC or,000hz) 00 V DC 50 V AC/minute Measured by applicable connector. 000 cycles 5ç to +85ç 5ç to +60ç Frequency:0 to 50Hz, single amplitude of 0.75mm, 5min/cycle, total 0 cycles. Acceleration of 490m/s, ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. Temperature: -55ç/+5ç to +35ç/+85ç/5ç to+35ç Time:30/5/30/5(Minutes) 5cycles 96 hours at 40ç And RH 90% to 95%. 5% salt water solution for 48 hours. Excludes wire conductor resistance. *Unless otherwise specified, refer to JIS C 540 Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. Materials Products Insertion f. with drawal f. 7pos. 5N max..6n min. 7pos. 30N max. 3N min. Components Insulator Contacts Shell Metal fitting Insulator Contacts Shell Metal fitting Metal grounding post Insulator Contacts Rear insert Shell Cover Shield Screw lock Tapping screw Cover Shield Screw lock Screw insulator Tapping screw Cover Shield Lock spring Tapping screw Cover Shield Lock spring Button Tapping screw Screw lock Waher Spring washer Metal clamp 37pos. 36N max. 3.3N min. 5pos. 43N max. 3.8N min. Material Polyamide resin Copper alloy Stainless steel Stainless steel Polyamide resin Copper alloy Stainless steel Brass Steel Polyamide resin Copper alloy PBT resin Stainless steel Polycarbonate resin Stainless steel Steel Steel Polycarbonate resin Stainless steel Steel Polyamide resin Steel Polycarbonate resin Stainless steel Stainless steel Steel Polycarbonate resin Stainless steel Stainless steel Polycarbonate resin Steel Steel Steel Steel Brass Finish Black Selective gold plated Tin plated Selective Tin plated Black selective gold plated Tin plated Tin plated Nickel plated Black Selective gold plated Black,Natural Nickel plated Black Nickel plated Nickel plated Black chromate(cr+3) Black Nickel plated Nickel plated Black Black chromate(cr+3) Black Nickel plated Black chromate(cr+3) Black Nickel plated Black Black chromate(cr+3) Nickel plated Nickel plated Nickel plated Remarks UL94V-0 UL94V-0 UL94V-0 UL94V-0 UL94V-0 UL94V-0 UL94V-0 UL94V-0 UL94V-0 UL94V-0 4
Screw lock type Receptacle connector Right angle type [7pos. DH60-7P] 8 5 8 0.8 4 9.. No.8 No.9 M.3 0.4 0. 0 7 6 Ø. 9(BOSS PITCH) 9.(CLAMP METAL PITCH) 4.8 0.9.6 4.8.56 [7pos. DH60-7P] 30 3 0.8 4 8 4. 7. 3 4 M.3 0.4 5 7 6 6 0.. Ø 4(BOSS PITCH) 4.(CLAMP METAL PITCH) 9.8 0.9.6 4.8.56 [37pos. DH60-37P] 35 8 0.8 4 8 9.. 8 9 M.3 0.4 0. 0 Ø 9(BOSS PITCH) 9.(CLAMP METAL PITCH) 34.8 No.37 No.36. 0.9.6 4.8.56 5
[5pos. DH60-5P] 4 5 0.8 4 8 36. 9. 5 6 M.3 0.4 0. 7 8 Ø 36(BOSS PITCH) 36.(CLAMP METAL PITCH) 4.8 No.5 No.50. 0.9.6 4.8.56 Straight type [7pos. DH80-7P] Ø 7.8 6.5.5 4.4 0. 6.5 4.6 4 4.9.5 30.8 4. 7. 3 4 5 6 7 6 M.3 0.4.4.75 6
Lock screw [Applicable panel thickness.4 to.6mm:dh-lna] [Applicable panel thickness 0.9 to.mm:dh-lna-w4] M 0.4 4.4 4.4.5 M 0.4 4.4 0.4 4.4.5 M.3 0.4 M.3 0.4 [Applicable panel thickness to 0.8mm:DH-LNA-W8] [No panel:dh-lna-w6] M 0.4 4.4 0.8 4.4.5 M 0.4.6 4.4 4.4.5 M.3 0.4 M.3 0.4 7
Cover case Screw lock [7pos. DH-7-CVB] Note. 3 This product is delivered separately. A recommended screw tightening torque to lock screw(dh-lna***) should be from 0.06 to 0.07N m. A recommended screw tightening torque for covers to be from 0. to N m. Ø7.8 3 5.4 3.4 6.7 [7pos. DH-7-CVB] Ø8.8 3 5.4 3.4 3.7 8
[37pos. DH-37-CVB] Ø0.3 3.7 5.4 39 36 [5pos. DH-5-CVB] Ø. 3.7 4.3 5.4 39 43 9
Hand screw [7pos. DH-7-CVB] Note. 3 This product is delivered separately. A recommended screw tightening torque to the lock screws to be from 0.06 to 0.07N m. A recommended screw tightening torque for covers to be from 0. to N m. Ø7.8 3 5.4 3.4 6.7 *Available in the near future [7pos. DH-7-CVB] Ø8.8 3 5.4 3.4 3.7 *Available in the near future 0
[37pos. DH-37-CVB] Ø0.3 3 5.4 39 36.7 *Available in the near future [5pos. DH-5-CVB] Ø. 3 5.4 39 43.7 4.3 *Available in the near future
One Touch Lock Type Receptacle connector Right angle type [7pos. DH60A-7P] 5.8 8 0.8 5. 4 8 7... No.8 No.9 M 0.4 0. 0 7 6 Ø 0.95 9(BOSS PITCH) 9.(CLAMP METAL PITCH) 4.8 0.9.6 4.8.56 0.7 [7pos. DH60A-7P] 30.8 3 0.8 6. 7. 3 4 M 0.4 4. 4.8 5. 8 0. 5 7 6 6 Ø 0.95 4(BOSS PITCH) 4.(CLAMP METAL PITCH) 9.8 0.9.6.56 0.7 [37pos. DH60A-37P] 35.8 8 0.8 4 8 7. 3.. 8 9 M 0.4 4.8 5. 0. 0 Ø No.37 No.36 0.95 9(BOSS PITCH) 9.(CLAMP METAL PITCH) 34.8 0.9.6.56 0.7
[5pos. DH60A-5P] 4.8 5 0.8 5 6 M 0.4 7 8 Ø No.5 No.50 0.95 [7pos. DH80A-7P] Ø 7.8.3 6.5.5.5.45 30.8 6. 7. 6.5 4.6 4.4 0. 4 4.9 5. 4 8 34. 38. 9. 0. 36(BOSS PITCH) 36.(CLAMP METAL PITCH) 4.8 0.9.6 4.8.56 0.7 Straight type 3 4 5 6.75 7 6 M 0.4.4 3
Cover case Metal button type [7pos. DH-7-CTB] Note. This product is delivered separately. A recommended screw tightening torque for covers to be from 0. to N m. Ø7.8 7 3.4 6.7 [7pos. DH-7-CTB] Ø8.8 3 7.7 3.4 4
[37pos. DH-37-CTB] Ø0.3.7 7 39 36 [5pos. DH-5-CTB] Ø. 7 39 43.7 4.3 5
Plastic button type [7pos. DH-7-CTB] Note. This product is delivered separately. A recommended screw tightening torque for covers to be from 0. to N m. Ø7.8.7 7 3.4 6 [7pos. DH-7-CTB] Ø8.8 7 3.4 3.7 6
[37pos. DH-37-CTB] Ø0.3 7 39 36.7 [5pos. DH-5-CTB] Ø. 7 39 43.7 4.3 7
Plug unit IDC type [7pos. DH30B-7S] No.9 No.8 No.9 4.8.35 8 Bundled parts 3.75 9.55 6.65 7 7 0 8. 6.0 No.9 7 6.8 3.9 No.8 3.9 0 6.8 6 6 7 0 [7pos. DH30B-7S,DH30B-7S] 3 4 4 9.8 7.35 3 Bundled parts 3.75 9.55 6.65 7 5 8. 6.0 3 5 7 3.9 4 6 6 6 6 6.8 6.8 3.9 6 6 7 5 *DH30B-7S and DH3B-7S are different holes in the attached parts. 8
[37pos. DH30B-37S] 9 8 9 4.8.35 8 Bundled parts 3.75 9.55 6.65 No.37 0 8. 6.0 9 No.37 No.36 0 6.8 3.9 8 3.9 0 6.8 No.36 No.37 [5pos. DH30B-5S] 5 6 6 3.8 9.35 5 3.75 9.55 6.65 Bundled parts No.5 4 7 8. 6.0 5 7 No.5 3.9 3.9 No.50 8 6 8 No.50 6.8 6.8 No.5 7 8 8 9
Solder contact type [7pos. DH40-7S] 4 9.8 7.35 3 3 4 DH40 3.75 6.65 9.55 7 5 8. 5.7 5 6 7 6 [37pos. DH40-37S] 9 4.8.35 8 DH40 8 9 3.75 6.65 9.55 No.37 7 0 8. 5.7 0 No.37 No.36 0
Metal clamp [7pos. DH-7-CMB(6.3)] (Cable outer diameter 6.3mm) [7pos. DH-7-CMB(6.9)] (Cable outer diameter 6.9mm) 4.7 5.5.3 9.3 3.5 0. 9 R3.55 R3.35 [7pos. DH-7-CMB(7.3)] (Cable outer diameter 7.3mm) 4.7 5.5 4.4 0. 9.5 0.6 4.7 5.5 R4. R4 [37pos. DH-37-CMB(8.8)] (Cable outer diameter 8.8mm) 4.7 6. 7.6. 0.8.4 R4.3 R4.5 R4.6 R4.8
[5pos. DH-5-CMB(9.6)] (Cable outer diameter 9.6mm) 4.7 6. 8.4 3. 0.8 3 R5. R5
Recommended PCB Mounting pattern DH60-**P, DH60A-**P PAD FOR TERMINAL PAD FOR SHELL 3....3 -Ø.(HOLE) DH80-7P POSITIONING HOLE PCB END P= 0.3 3-Ø A B C D E F -(Land) -.5(Land) R -(Land) R -Ø.4(TH) R0.85 R0.35 -.55(TH) -3.55(Land) -0.65(TH) -.65(Land) :PATTERN PROHIBITION AREA :REFERENCE PLANE POSITION (PATTERN PROHIBITION AREA).9.5 DH60-7P DH60A-7P DH60-7P DH60A-7P DH60-37P DH60A-37P DH60-5P DH60A-5P A 4.8 9.8 34.8 4.8 B 9. 4. 9. 36. C 4.3 9.3 4.3 3.3 D 8 3 8 5 Unit:mm E F 9 6 4 3 9 36 36 43 Ø.6(TH) Ø3.(Land) PAD FOR SHELL 0.43 7.8 4. 3 PAD FOR TERMINAL 3 4.6(Land) (TH) 7.4.75 4.4 Ø.(Hole) 5 6 6.5 POSITIONING HOLE 7 6 0.65(TH).5(Land) DH80A-7P Ø.8(TH) Ø.4(Land) PAD FOR SHELL 0.43 7.8.3 3 PAD FOR TERMINAL 3 4.6(Land) (TH) 7.4.75 4.4 5 6 Ø.(Hole) 6.5 POSITIONING HOLE 7 6 0.65(TH).5(Land) Terminal No.chart DH60-**P, DH60A-**P D No.(N+3)/ No.(N+5)/ No.(N+)/ No.N No.(N-)/ No.(N-) *N:Number of positions 3
Panel cutout Screw lock type Panel cutout for reference (Right angle type, Straight type) (The dimension is specified based on the center of the connector interface) DH-LNA(CL44-0045-0-00).5 A B Ø.5.5 PCB MOUNTING SURFACE POSITION 5 5 DH-LNA-W4(CL44-0046--00) DH-LNA-W8(CL44-0004--00) DH-LNA-W6(CL44-0005-5-00) C D.9 *Please set piercing R as less than R. -R. PCB MOUNTING SURFACE POSITION *Please set piercing R as less than R. A B C D dimension table Unit:mm Number of contacts A B C D 7 9. 3.7 5 7 4. 8.7 7 0 37 9. 3.7 3 5 5 36. 30.7 39 3 Connector mounted on PCB (For example, panel thickness is.6mm) *The drawing is shown sample of DH60-7P. *DH80-7P PCB t=.6 4.8 *PANEL t=.6 8.5 30 4. PCB PANEL BACKSIDE *LOCK SCREW (DH-LNA) PANEL PCB MOUNTING SURFACE *An attachment to the panel needs screws shown in the table below. *PANEL t=.6 4.9 PCB t=.6 PCB MOUNTING SURFACE 4.6 30.8 4. Panel cutout for reference PCB PANEL BACKSIDE PANEL Applicable panel thickness(mm) Part No. Code No..4 to.6 DH-LNA 44-0045-0-00 0.9 to. DH-LNA-W4 44-0046--00 to 0.8 DH-LNA-W8 44-0004--00 No panel DH-LNA-W6 44-0005-5-00 *The recommended screw tightening torque to be from 0. to 0.3 N m 4
One Touch Lock Type Panel cutout for reference (Right angle type, Straight type) (The dimension is specified based on the center of the connector interface) A B.4.5 5 -R. PCB MOUNTING SURFACE POSITION *Please set piercing R as less than R. A B dimension table Number of contacts A 7 3.5 7 8.5 37 33.5 5 4 Unit:mm B 8 3 8 35 Connector mounted on PCB *DH60A-7P is representative examples. *DH80A-7P PCB PANEL BACKSIDE 30.8 6. *SCREW FOR INSTALATION PANEL PCB MOUNTING SURFACE 4.8.5 8.4 8 5. t=.6 MAX 30.8 6. 4.6 t=.6 PCB PCB 4.9 PCB MOUNTING SURFACE PANEL BACKSIDE t=.6max 0.6 Ø3.5 *SCREW FOR INSTALATION PANEL PCB t=.6 *Installation with the panel must use a dedicated screw. Purchase:qHRS part No.[DH60A-SCREW] CL No.[CL44-004-] wnittoseiko Co., Ltd. [FINE PAN HEAD MACHINE SCREW TYPES] *SCREW FOR INSTALATION Ø3.5 0.6 *Installation with the panel must use a dedicated screw. Purchase:qHRS part No.[DH80A-SCREW] CL No.[CL44-0059-4] wnittoseiko Co., Ltd. [FINE PAN HEAD MACHINE SCREW TYPES] *SCREW FOR INSTALATION Ø3.5 M 0.4 0 0.6 M 0.4 5 5
Applicable tools Process Part No. CL No. Cable end processing manual work Upper level wire arranging 3 4 Upper level press fitting Lower level wire arranging wire arranging tool : DH/CA-MO CL90-83-0 5 Lower level press fitting 6 Cable cutting manual work(nipper etc.) ➀ IDC clamping tool:dh/idck-mp CL90-85-5 ➁ attachment for 7pos:DH-7UNIT CL90-86-8 attachment for 7pos:DH-7UNIT CL90-87-0 7 IDC attachment for 37pos:DH-37UNIT CL90-88-3 attachment for 5pos:DH-5UNIT CL90-89-6 ➂ HI-FLEX termination press (Select appropriate attachment of each pin count from ➁.) CL550-008- ➀ IDC clamping tool:dh/idck-mp CL90-85-5 ➁ attachment for DH-7-CMB(6.3):DH-7-CMB(6.3)UNIT CL90-90-5 attachment for DH-7-CMB(6.9):DH-7-CMB(6.9)UNIT CL90-94-6 8 Cable clamping attachment for DH-7-CMB(7.3):DH-7-CMB(7.3)UNIT CL90-9-8 attachment for DH-37-CMB(8.8):DH-37-CMB(8.8)UNIT CL90-9-0 attachment for DH-5-CMB(9.6):DH-5-CMB(9.6)UNIT CL90-93-3 ➂ HI-FLEX termination press (Select appropriate attachment of each pin count from ➁.) CL550-008- 9 Cover attaching manual work(torque driver etc.) *Customers already having HI-FLEX termination press can apply it to this product assembly. *Each ➀ and ➂ of 7. IDC and 8. Clamping are the same tools. All the parts ➀, ➁ and ➂ are required for each 7. IDC and 8. Clamping processes for mass-production. 6