A-C Capacitors for Motor Run Applications

Similar documents
Snubber, High Current DC, and Switching Capacitors

Product details are described at websites

Aerovox Corp. Capacitors for HID Lighting Applications. Catalog HID-cap 2004-R0

PhaseCap Premium PFC Capacitors Gas-impregnated n Dry type n Concentric winding n Wavy cut n Triple safety system

Surge Arresters. UltraSIL Housed VariSTAR Station Class Surge Arresters GENERAL CONSTRUCTION

Single Pole Circuit Protectors 55. Multi-Pole Circuit Protectors 56. Configurations 58. Operating Characteristics 59.

CONTROLLIX CORPORATION CONTROLLIX.COM LOW VOLTAGE AUTOMATIC SWITCH CAPACITOR BANK SPECIFICATIONS

INSTRUCTION MANUAL. Type SWF. Sine Wave Filters 480 Volts, 60Hz. Page 1 of 14. April 15, 2010: updated capacitor UL File number)

AP/UP, AP/MIL Series Magnetic Circuit Protectors

POWER CAPACITORS. Cylindrical capacitor standard duty

APEC 2011 Special Session Polymer Film Capacitors March 2011

Surge arresters. UltraSIl Polymer-Housed VariSTar Type UI Intermediate-Class Surge arresters. General. COnSTrUCTIOn

Medium Power Film Capacitors

PhiCap Capacitors for Power Factor Correction

Motor Run & General Purpose AC Capacitors. AC Film Capacitors for. Purpose Applications. RoHS COMPLIANT. Intelligent Capacitor Solutions

Motor Run & General Purpose AC Capacitors. AC Film Capacitors for. Purpose Applications. RoHS COMPLIANT. Intelligent Capacitor Solutions

DATA SHEET. 152 RMH Aluminum electrolytic capacitors Radial Miniature, High voltage. BCcomponents

Wet Tantalum Tubular Capacitors

Technical Specification For Outdoor Substation Harmonic Filter Banks

Snap-in Type Aluminium Electrolytic Capacitors

MTU2 Series Isolated 2W Single & Dual Output SM DC/DC Converters

Power Factor Correction Capacitors Type LKT

M T E C o r p o r a t i o n MATRIX FILTER. SERIES B Volts, 50HZ USER MANUAL PART NO. INSTR REL MTE Corporation

Power System Solutions (PSS)

According to IEC , grade 1.1

PHE426 Single metallized film pulse capacitor, polypropylene dielectric According to IEC , grade 1.1

Power Factor Correction Capacitors Type LKT

MTU1 Series Isolated 1W Single & Dual Output SM DC/DC Converters

55 C to +105 C 6.3, 10, 16, 25, 35, 50, 63, 80 & 100 Vdc. Shelf Test: C. 0.3 mm Max. A

M T E C o r p o r a t i o n MATRIX FILTER. SERIES B Volts, 50HZ USER MANUAL PART NO. INSTR REL MTE Corporation

SECTION AIR TERMINAL UNITS

M T E C o r p o r a t i o n. MTE Series RL. Line/ load Reactors USER MANUAL PART NO. INSTR -011 REL MTE Corporation

Type SLP 105 C Snap-In Aluminum Electrolytic Best Value 105 C Snap-In Type

DYNACOMP. The top-class reactive power compensator

YAGEO Corporation Date: 01/17/2007

Ballasts For High Intensity Discharge Lamps

Dimensions mm. IMax Multiplier 1kHz 10kHz. Ambient Temperature. Fixing symbol code

Medium Voltage Metal-Enclosed Switches

High Power Film Capacitors

Model Number Structure

Power Factor Correction Capacitors Type LKT

Highest CV/cc Conductive Polymer Chip Capacitors Undertab FEATURES

Type AHA SMT Aluminum Electrolytic Capacitors -55 C to +105 C - Long Life

Table of Contents. HCC Contactor Nomenclature

MTB. MKT box with radial terminals small size general purpose. Ed. 04 Rev Dissipation factor (DF), max. tgδ x10-4, measured at 25 ±5 C

NXE1 Series Isolated 1W Single Output SM DC/DC Converters

APPLICATIONS Smart phone, Tablets, Notebook, LCD TV, Power supplies. P (0.081) 1.35 (0.050) 1.50 (0.059) max

SELECTION GUIDE. Nominal Input Voltage. Output Voltage. Input Current. Input reflected ripple current

16 ~ 250 VDC -40 ~ +105 C 820~250000µF ± 20% For capacitance values > 33000µF, add the value of:

1.0 Rated Values and Operational Data

SWITCH-MODE CERAMIC CAPACITORS

Features. Samples. Units Continous: Steady State Applied Voltage: DC Voltage Range (VM(DC)) 150 to 970 V AC Voltage Range (V M(AC)RMS

Medium Voltage Metal-Enclosed Switches

Metal-Enclosed Switches. Medium Voltage. Medium Voltage Metal-Enclosed Switches Contents

MEE1 Series Isolated 1W Single Output DC/DC Converters

Aug07 Rev A All Paragraphs Revised

KEMET Part Number: C276CC35250AA1J

SELECTION GUIDE - SINGLE OUTPUT 1. Nominal Input Voltage Output Voltage

MOV Transient Voltage Suppressors

Large Can Aluminum Electrolytic Capacitors

LV Capacitor CLMD Reliability for Power Factor Correction

MIL-PRF Series. Military Conventional Wet Tantalum OUTLINE DIMENSIONS. CASE DIMENSIONS: millimeters (inches)

MAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI

CAPACITORS FOR POWER ELECTRONICS

NDS6 Series Isolated 6W Wide Input Single & Dual Output DC/DC Converters

YAGEO Corporation Date: 2/22/2011

SELECTION GUIDE. Nominal Input Voltage. Output Voltage. Input Current. Input reflected ripple current

Performance Characteristics -40 to +85 (160Vdc~450Vdc) -25 to +85 (500Vdc~630Vdc) 160 to 630 V DC Working Voltage(VDC) 160~ ~550

Snap-in Type Aluminium Electrolytic Capacitors

MTE SERIES RLW. World REACTORS USER MANUAL PART NO. INSTR 030 REL MTE Corporation

Technical Specification for Pole Mounted Capacitor Rack

Ensuring the Safety Of Medical Electronics

Fuse/Var Technical Data

PPS. MKP axial terminals snubber medium-high pulse applications high current high frequency switching. Ed. 04 Rev

Index Low Voltage Network Quality. Low Voltage Network Quality

SELECTION GUIDE. Nominal Input Voltage. Output Voltage. Input Current. Input reflected ripple current

SELECTION GUIDE. Nominal Input Voltage. Voltage. Output. Reflected ripple current. Case Temperature rise above ambient ABSOLUTE MAXIMUM RATINGS

Power factor correction Harmonic filtering Dynamic flicker compensation

PD-Series Ground Fault Circuit Protection

3-TERMINAL ADJUSTABLE REGULATOR LM317L

Film Capacitors. Metallized Polyester Film Capacitors (MKT) Date: August 2004

A. Fan motors and associated equipment shall be sized to operate at 110% of calculated loads and capacities.

Model Number Structure

For capacitance values > 33000µF, add the value of: 3 CV (µa) max. after 5 minutes; C = Capacitance in µf, V = WV ~ k 10k

CMR Series Isolated 0.75W Single and Dual Output Isolated DC/DC Converters

.3 Section Waste Management and Disposal.

Metallized Polypropylene Film Capacitors (MKP)

SELECTION GUIDE. Nominal Input Order Code 1 Voltage. Output Voltage

Rated voltage Capacitance Cap. Tol. Suffix Suffix. Crimped taping. Ammo 3 E C Q P R Z. Rated voltage Capacitance 7.5 mm.

STRIDER ESSENTIAL SERIES ST50F-ESB ST40F-ESB Power for everything you need

Plastic Film Capacitors

Highest CV/cc Conductive Polymer Chip Capacitors Undertab FEATURES

NTA Series Isolated 1W Dual Output SM DC/DC Converters

MEA1 Series 1kVDC Isolated 1W Dual Output DC/DC Converters

M T E C o r p o r a t i o n. dv/dt Filter. Series A VAC USER MANUAL PART NO. INSTR REL MTE Corporation

Type AVS SMT Aluminum Electrolytic Capacitors - General Purpose, 85 C

MSB Metallized polyester film capacitor MKT - High performance

STANDARD CASE DIMENSIONS: millimeters (inches) W 1 dimension applies to the termination width for A dimensional area only.

Capacitance Range. 2 F 100 F Standard Tolerance 10% Capacitance Variation Through Life 2% Dissipation Factor C 0.

NXE2 Series Isolated 2W Single Output SM DC-DC Converters

Transcription:

CPD 510 03 / 08 A-C Capacitors for Motor Run Applications

Capacitor Application Data Sheet To ensure correct selection of a capacitor for your application, please provide the information indicated below. This sheet may be duplicated or additional copies may be obtained from RBC. Of particular importance are the voltages and current waveforms complete with values of voltage and current over a complete cycle. PRIMARY INFORMATION ( Essential ) Send this data to your local RBC Sales Representative or directly to: GE Capacitors by Regal Beloit 11970 PELLICANO DR., SUITE 300 EL PASO, TEXAS 79936 USA Fax: (915) 849-5799 1. Application: 2. Capacitance: Tolerance: 3. Peak Voltage: RMS Voltage: 4. Peak Current: RMS Current: 5. Transient Voltage: Duration: Freq. Of Occurrence: 6. Frequency or Repetition Rate (Hz): Duty Cycle: 7. Ambient Temperature: Max.: Min.: 8. Capacitor Charge Time: Discharge Time: 9. Required Operating Life (Hours): 10. Waveforms: SECONDARY INFORMATION (Provide as Appropriate) 11. Physical Size Limitations: 12. Mounting Requirements: 13. Applicable Specifications: 14. Type of cooling Available: 15. Unusual Atmospheric Conditions: 16. Other special Requirements: 17. Number of samples Required: 18. Potential Usage:

1 Table of Contents Descriptive Information 1 Product Safety 3 Motor Run Capacitors-Gem III ( Single Section ) 4 Motor Run Capacitors -Gem III ( Dual Section ) 6 Motor Run Capacitors -Gem III (Dual Concentric) 7 Application Data 9 Outline 11 Mounting Hardware 12 Descriptive Information RBC Capacitors for Motor Run Applications Metallized film capacitors are unsurpassed in terms of size, weight, performance, and reliability for AC applications. RBC - Capcom brings over 60 years of capacitor manufacturing experience to the product lines described in this publication. These capacitors represent the best in product design for long-term reliability and safe operation. RBC s materials, product, and process development work continue to provide capacitor users with outstanding total value. The Gem III Motor Run Capacitors are widely used with permanent split phase capacitor motors for the more efficient use of electricity. These motors are used in heating and cooling equipment, appliances, business machines, office equipment, and a wide variety of light industrial equipment. CPD 510 03 / 08

GEM III Construction 2 Descriptive Information RBC s Gem III capacitors are manufactured with high-grade metallized polypropylene film. This film is in the range of 5 to 10 microns thick, depending on the application voltage and conditions. The metallized electrode is several hundred angstroms thick. The film is wound into capacitor rolls on high-speed, highprecision machines. The winding is extremely tight so that there is not enough space between the layers for corona (localized partial electrical discharges) to occur. The rolls are sprayed on both ends with metal to make connection to the extremely thin edges of the metalized electrodes. This process is critical to the quality and performance of the capacitors. The rolls are assembled in metal cases, RBC s proprietary Dielektrol VI liquid is introduced under vacuum, and the capacitors are sealed. They are then subjected to 100% electrical testing for capacitance, dissipation factor, and high potential electrical withstand, both terminal-to-terminal and terminal-to-case. CPD 510 03 / 08

Product Safety 3 Mounting Considerations Pressure Sensitive Interrupter All the capacitors listed in this publication contain RBC's Pressure Sensitive Interrupter (PSI). This device, developed by RBC, is designed to sense the build-up of pressure within the capacitor if a fault occurs and to interrupt the internal electrical connections before the case can rupture. The PSI carries U.L. * recognition for applications where the specified fault currents are not exceeded. The fault current is the maximum current that is available from the circuit to flow through the capacitor if the capacitor were to become a short circuit with zero impedance. It is the responsibility of the capacitor user to determine what the available fault current is for a particular application. In the Catalog Number listings a four character U.L. Code, Pxxx, is given. This number is part of the listing for RBC in U.L. File No. E7793. When applying to U.L. for approvals or recognition of equipment using these capacitors refer to the Pxxx number and not the Catalog Number of the capacitor in question. Proper operation of the PSI requires that the cover be able to expand without restriction. The following mounting considerations should be noted in mounting these capacitors. Vertical Clearance There must be sufficient clearance between the tops of the terminals (and/or the assembled wire connectors) and a plane perpendicular to the capacitor terminals. This clearance must be at least 0.5 inches plus the electrical spacing requirements of the end application. Cut-Out Clearance In certain instances capacitors are mounted with the top of the capacitor case resting against the chassis and the terminals protruding through the chassis. Care must be taken to see that the cutout in the chassis is large enough. The following dimensions are recommended. Style a b Style a A 2.00 1.00 P 1.62 B 2.25 1.25 S 1.88 C 2.50 1.62 T 2.38 D 3.25 1.62 *Underwriter's Laboratories

Motor Run Capacitors Gem III 4 370 and 440 Volts AC This capacitor series is designed specifically for the motor run applications where the capacitors are used in conjunction with permanent split capacitor type motors. They may be used on either 50 or 60-Hertz systems but should not be used at higher frequencies or in applications where higher frequency harmonics are present. For those types of applications the General Purpose AC Capacitors shown on the following pages should be used. If there is any question regarding the correct application of these products, please contact your RBC sales representative. SPECIFICATIONS: Available Capacitance Range: 2 to 120 µf Capacitance Tolerance: ± 6% Capacitance Variation with Temperature: See chart M-3 on page 9. Rated Voltage: Leakage Current: Frequency: Operating Temperature: Storage Temperature: Operating Life: Dissipation Factor: Material/Finish: Terminations: Dielectric Fluid: Internal Protection: See Rating Tables. Rating is the 50/60 Hz RMS voltage for a sinusoidal waveform. 30 µa maximum 50/60 Hz For higher frequencies use the General Purpose AC Capacitor Series. -40 C to +70 C -40 C to +90 C 60,000 hours with 94% survival 0.1% maximum Unpainted Aluminum case, tern plate steel cover. Contact RBC if material/finish to meet UL outdoor standards is required. Combo terminal: 0.250 x 0.031 quick connect blades. Dielektrol VI UL recognized Pressure Sensitive Interrupter. See Ratings Table for RBC s UL code Number listed under RBC s UL File E7793 (N). For UL submittals with these capacitors use the RBC Pxxx number not the Catalog Number. The corresponding generic UL designation that includes the Available Faults Current (AFC) rating is given below. All these capacitors are capable of interrupting available fault currents of up to 10,000 amperes.

Motor Run Capacitors Gem III 5 *STANDARD RATINGS Capacitance (µf) Catalog Number Style Height C (in.) UL Code 370 Volts AC Nominal 3 27L987 A 1.56 P921 4 27L571 A 1.56 P921 5 27L570 A 1.56 P921 6 97F5706 A 2.12 P921 7.5 27L566 A 2.12 P921 10 97F9002 A 2.88 P921 12.5 27L572 A 2.88 P921 15 27L567 A 2.88 P921 20 97F9602 P 2.88 P965 25 97F9606 P 2.88 P965 30 97F9608 P 3.88 P965 35 97F9611 P 3.88 P965 40 97F9614 P 3.88 P965 45 97F9884 P 4.75 P965 50 97F9802 P 4.75 P965 55 97F9010 S 4.75 P968 60 97F5276 T 3.88 P969 65 97F9011 T 3.88 P969 70 97F9012 T 4.75 P969 440 Volts AC Nominal 3 97F5437 A 2.12 P921 4 97F5337 A 2.88 P921 5 97F5339 A 2.88 P921 6 97F5436 A 2.88 P921 7.5 27L695 A 2.88 P921 10 97F5300 A 3.88 P921 12.5 97F9080 A 4.75 P921 15 97F9625 A 4.75 P921 20 97F9630 P 3.88 P965 25 97F9632 P 3.88 P965 30 97F9635 P 3.88 P965 35 97F9639 S 3.88 P968 40 97F9642 S 3.88 P968 45 97F9645 S 4.75 P968 50 97F5211 T 3.88 P969 55 97F9042 T 4.75 P969 60 97F9043 T 4.75 P969 65 97F5241 T 4.75 P969 70 97F5251 T 4.75 P969 * It is RBC s goal to serve you with the most cost effective and the highest quality capacitor designs. Standardization to the catalog type shown is a major program at RBC. However, RBC remains sensitive to your needs and requirements, and will continue to offer the above ratings (and more) in case configurations to meet your application (s). Style P, S, and T Style K J P 1.75 1.88 S 2.00 2.12 T 2.50 2.62 Style A

Motor Run Capacitors Gem III 6 DUAL SECTION *STANDARD RATINGS Capacitance (µf) (µf) (Herm) (Fan) Catalog Number Style 370 Volts AC Nominal Height C(in.) UL Code 10 10 27L956 C 2.12 P923 15 5 97F9437 C 2.88 P923 15 7.5 97F9526 C 2.88 P923 20 5 97F9673 C 2.88 P923 20 7.5 97F9991 C 2.88 P923 25 5 97F9675 C 2.88 P923 25 7.5 97F9677 C 2.88 P923 30 5 97F9681 C 3.88 P923 30 7.5 97F9683 C 3.88 P923 35 5 97F9796 C 3.88 P923 35 7.5 97F9864 C 3.88 P923 40 5 97F9840 C 3.88 P923 40 7.5 97F9845 C 3.88 P923 45 5 97F9859 C 3.88 P923 45 7.5 97F9841 C 3.88 P923 50 5 97F9885 C 4.75 P923 50 7.5 97F9858 C 4.75 P923 440 Volts AC Nominal 15 5 97F9694 C 2.88 P923 15 7.5 97F9992 C 2.88 P923 20 5 97F9695 C 2.88 P923 20 7.5 97F9696 C 3.88 P923 25 5 97F9730 C 3.88 P923 25 7.5 97F9993 C 3.88 P923 30 5 97F9994 C 3.88 P923 30 7.5 97F9995 C 3.88 P923 35 5 97F9842 C 4.75 P923 35 7.5 97F9892 C 4.75 P923 40 5 97F9843 C 4.75 P923 40 7.5 97F9996 C 4.75 P923 Style C Style RBC Code Generic UL Code C P923 C10000AFC D P924 D10000AFC * It is RBC s goal to serve you with the most cost effective and the highest quality capacitor designs. Standardization to the catalog type shown is a major program at RBC. However, RBC remains sensitive to your needs and requirements, and will continue to offer the above ratings (and more) in case configurations to meet your application (s).

Motor Run Capacitors Gem III 7 CONCENTRIC ROUND *STANDARD RATINGS Style S,T Capacitance (µf) (µf) (Herm) (Fan) Catalog Number Style Height C(in.) UL Code 370 Volts AC Nominal 15 5 97F9810 S 2.88 P968 15 7.5 97F9811 S 2.88 P968 20 5 97F9814 S 2.88 P968 20 7.5 97F9966 S 2.88 P968 20 10 97F9967 S 2.88 P968 25 5 97F9803 S 2.88 P968 25 7. 5 97F9826 S 2.88 P968 25 10 97F9827 S 3.88 P968 30 3 27L955 S 2.88 P968 30 5 27L877 S 2.88 P968 30 7.5 97F9868 S 3.88 P968 30 10 97F9828 S 3.88 P968 35 5 97F9834 S 3.88 P968 35 7.5 97F9829 S 3.88 P968 40 5 97F9849 S 3.88 P968 40 7.5 97F9855 S 3.88 P968 40 10 97F9831 S 3.88 P968 45 5 27L880 S 3.88 P968 45 7.5 27L947 S 3.88 P968 45 10 97F9832 S 4.75 P968 50 5 97F9970 S 4.75 P968 50 7.5 97F9971 S 4.75 P968 50 10 97F9972 S 4.75 P968 55 5 97F9815 T 3.88 P969 55 7.5 97F9973 T 3.88 P969 55 10 97F9974 T 3.88 P969 60 5 27L954 T 3.88 P969 60 7.5 97F9817 T 4.75 P969 80 5 27L651 T 4.75 P969 Style K J S 2.00 2.12 T 2.50 2.62 * It is RBC s goal to serve you with the most cost effective and the highest quality capacitor designs. Standardization to the catalog type shown is a major program at RBC. However, RBC remains sensitive to your needs and requirements, and will continue to offer the above ratings (and more) in case configurations to meet your application (s).

Motor Run Capacitors Gem III 8 CONCENTRIC ROUND *STANDARD RATINGS Style S,T Capacitance (µf) (µf) (Herm) (Fan) Catalog Number Style Height C (in.) UL Code 440 Volts AC Nominal 15 5 97F9997 S 2.88 P968 15 7.5 97F9998 S 3.88 P968 20 5 97F9975 S 2.88 P968 20 7.5 97F9976 S 3.88 P968 25 5 97F9978 S 3.88 P968 25 7. 5 97F9979 S 3.88 P968 30 5 97F9981 S 3.88 P968 30 7.5 97F9982 S 3.88 P968 30 10 97F9983 S 3.88 P968 35 5 97F9848 S 4.75 P968 35 7.5 97F9881 S 4.75 P968 40 5 97F9838 S 4.75 P968 40 7.5 97F9882 S 4.75 P968 45 5 27L889 S 4.75 P968 40 5 27L946 T 2.88 P969 45 7.5 97F9883 T 3.88 P969 50 5 27L569 T 4.25 P969 50 7.5 97F9987 T 4.75 P969 55 5 97F9839 T 4.75 P969 55 7.5 97F9874 T 4.75 P969 60 5 97F9897 T 4.75 P969 Style K J S 2.00 2.12 T 2.50 2.62 * It is RBC s goal to serve you with the most cost effective and the highest quality capacitor designs. Standardization to the catalog type shown is a major program at RBC. However, RBC remains sensitive to your needs and requirements, and will continue to offer the above ratings (and more) in case configurations to meet your application (s).

Motor Run Capacitors Gem III Application Data 9 Life Vs Temperature % of Chart M-1 Life Degrees C Life Vs Voltage % of Chart M-2 Life % of Rated Voltage

Motor Run Capacitors Gem III Application Data 10 Percent Capacitance Vs Temperature % Capacitance Chart M-3 Change Temperature ( Degrees C)

Outline 11 Round Style ( P,S,T ) Oval Style ( A,B,C,D ) Dual Oval Style ( C ) Oval Style 1A 1B 1D 1K A Oval 2.16 1.31 1.21 2.06 B Oval 2.69 1.56 1.47 2.58 C Oval 2.91 1.91 1.81 2.81 D Oval 3.66 1.97 1.88 3.56 C Dual Oval 2.91 1.91 1.81 2.81 Round Style 1K Dimensions Dimensions P Round 1.75 1.88 S Round 2.00 2.12 T Round 2.50 2.62 1J

Mounting Hardware 12 UNIVERSAL WRAP AROUND BRACKETS ROUND CASE STYLES Style Bracket Part Number a b c P 295A6016P31 1.75 1.12 1.31 S 295A6016P32 2.00 1.25 1.44 T 295A6016P33 2.50 1.50 1.69 UNIVERSAL WRAP AROUND BRACKETS OVAL CASE STYLES Style (2).156 dia holes suplplied with # 6-32 screw and nut Bracket Part Number A 128A2244ACP21 2.69 3.13 B 128A2244ABP25 3.27 3.70 C 128A2244ABP22 3.44 3.88 D 128A2244ABP23 4.19 4.63 d e WRAP AROUND BRACKETS ROUND AND OVAL CASE STYLES Style Bracket Part Number d e w t A K9827065P21 2.56 2.94 0.50 0.02 B K9827065P31 3.06 3.50 0.63 0.02 C 614A301P61 3.31 3.81 0.75 0.03 D 614A301P51 4.06 4.56 0.75 0.03 P 279A7235P24 2.50 2.88 0.75 0.04 S 279A7235P22 2.75 3.12 0.75 0.04 T 279A7235P23 3.25 3.62 0.75 0.04

Mounting Hardware 13 FOOTED BRACKETS Height Bracket Part Number Style d e A 2.56 3.00 2.12 302C920P210 B 3.13 3.56 2.88 302C920P113 C 3.38 3.81 3.88 302C920P115 D 4.13 4.56 4.75 302C920P116 5.75 302C920P209 P 2.33 2.76 S 2.57 3.00 T 3.07 3.50.187 PROTECTIVE BOOT PROTECTIVE CAP Boot Part Number 614A527P21 178A3744P21 Temperature Rating 60 0 C 105 0 C

AVAILABLE RBC COMPONENT CAPACITOR PUBLICATIONS Publication Description Replaces CPD-510 AC Motor Run Capacitors CPD-501 CPD-511 AC HID Lighting Capacitors CPD-501 CPD-512 General Purpose Capacitors CPD-501 CPD-517 Power Electrolytic Capacitors (General) New Pub. Please contact your RBC Sales Representative for further information Call or write directly to, GE Capacitors by Regal Beloit 11970 PELLICANO DR., SUITE 300 EL PASO,TEXAS 79936 USA Telephone: (915) 849-5757, (915) 849-5758 Fax: (915) 849-5799