Port Solenoid Valve Body Ported Series 000 For details about certified products conforming to international standards, visit us at www.smcworld.com. Type of actuation Type of actuation Body option Body option PE port (R) port PE port (R) port How to Order Rated voltage Electrical entry With light/surge voltage suppressor Manual override Body ported 1 2 0 L 01 1 2 2 position single solenoid 2 position double solenoid position closed center position exhaust center 0: Individual exhaust for the pilot valve : Common exhaust type for main and pilot valve Thread type 4(A)/2(B) port size Option Option F: With foot bracket (2 position single type only) Thread type Nil Rc F G N NPT T NPTF Note) Do not remove the factory installed bracket from models with the bracket option. R N 4 position pressure center Rated voltage 1 2 4 6 9 Option 100 VAC, 0/60 Hz 200 VAC, 0/60 Hz 110 VAC, 0/60 Hz 220 VAC, 0/60 Hz 24 VDC 12 VDC Other Electrical entry Grommet L plug connector M plug connector DIN terminal G: Lead wire L: With lead wire M: With MN: Without D: With connector length (Length 00 mm) lead wire lead wire 00 mm (Length 00 mm) Manual override Nil: Non-locking push type 4(A), 2(B) port size 01 Rc 1 8 C6 One-touch fitting for ø6 C8 One-touch fitting for ø8 Note) P, R1, R2 port: Rc 1/8 B: Locking type B (Slotted) C: Locking type C (Manual) H: Lead wire length 600 mm LN: Without lead wire LO: Without MO: Without DO: Without connector connector connector Light/Surge voltage suppressor Type LN, MN : With 2 sockets. Nil Z S None With light/surge voltage suppressor With surge voltage suppressor Not available for GZ, HZ and DOZ --
Series 000 Applicable for cylinder actuation (up to ø0). Compact size (Width: 18 mm) Low power consumption: 1.8 W DC Specifications Fluid 2 position single Operating pressure 2 position double range (MPa) position Ambient and fluid temperature ( C) Response time (ms) (1) 2 position single, double (at the pressure of 0. MPa) Max. operating frequency (Hz) Effective area position 2 position single, double position Manual override (2) Pilot exhaust method Lubrication Mounting orientation Impact/Vibration resistance (m/s 2 ) () Enclosure Air 0.1 to 0.7 0.1 to 0.7 0.1 to 0.7 10 to 0 C (No freezing. Refer to page -1-4.) 20 or less 0 or less 10 Refer to the table below. Non-locking push type, Locking slotted type, Locking lever type Individual pilot exhaust type, Common exhaust (pilot and main valve) type Not required Unrestricted 00/0 Dustproof Note 1) Based on dynamic performance test, JIS B 87-1981. (Coil temperature: 20 C, at rated voltage, without surge suppressor) Note 2) When operating the locking type manually, apply torque of 0.2 N m or less. Note ) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 4 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Refer to pages --60 to --6 for manifold use. Made to Order Specifications (For details, refer to page --8.) Solenoid Specifications Electrical entry AC 0/60 Hz Coil rated voltage (V) DC Allowable voltage fluctuation (%) Power consumption (W) Note) [Current ma] DC Apparent power (VA) [Current ma] Note) Surge voltage suppressor Indicator light Note) At rated voltage AC Inrush Holding Grommet (G)/(H), L plug connector (L), M plug connector (M), DIN terminal (D) 100, 200, 24, 48, 110, 220 24, 6, 12, 48 1 to +10% of rated voltage 1.8 (With indicator light 2.1) [24 VDC: 7 (With indicator light 87.)] Option 100 VAC: 4/0 Hz, 42/60 Hz 4./0 Hz, 4.2/60 Hz 200 VAC: 22./0 Hz, 21/60 Hz 100 VAC: /0 Hz, 0/60 Hz./0 Hz, /60 Hz 200 VAC: 17./0 Hz, 1/60 Hz DC: Diode, AC: ZNR DC: LED (Red), AC: Neon bulb --4
Port Solenoid Valve Body Ported Series 000 Flow Characteristics/Weight Valve model Type of actuation Port size 1,, (P, EA, EB) 4, 2 (A, B) Flow characteristics Note) 1 4/2 (P A/B) 4/2 / (A/B EA/EB) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv 2 Single position 2.2 0.6 0.8 Double Closed center Rc 1/8 Rc 1/8 1.8 0.7 0.4 20- -01 position Exhaust center 1.2 0.0 0.4 Pressure center.0 [0.8] 0.7[0.0] 0.78[0.2] 2 Single position 1.6 0. 0.4 Double C6 1.4 0.27 Closed center Rc 1/8 (One-touch 0. 20- -C6 position Exhaust center fitting for ø6) 1.1 0.7 0.27 Pressure center 1.8 [0.78] 0.6[0.40] 0.4[0.22] 2 Single position 2.0 0.9 0.2 Double C8 Closed center Rc 1/8 (One-touch 1.7 0. 0.42 20- -C8 position Exhaust center fitting for ø8) 1.2 0.8 0. Pressure center 1.9 [0.86] 0.7[0.46] 0.9[0.2] Note) [ ]: Denotes the normal position. Exhaust center: 4/2 /, Pressure center: 1 4/2 Cylinder Speed Chart Series 120-01 2.4 2.0.0[1.] 1.8 2.2 1.9 2.[1.] 1.6 2. 2.0 2.6[1.] 1.7 0.4 0.6 0. 0.49 0.[0.2] 0.7[0.9] 0.7 0.4 0.2 0. 0. 0.49 0.2[0.4] 0.61[0.8] 0.0 0.9 0.4 0.61 0.29 0.49 0.[0.49] 0.67[0.8] 0.9 0.42 Weight (g) Grommet 120 160 Use as a guide for selection. Please confirm the actual conditions with SMC Sizing Program. It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open. The average velocity of the cylinder is what the stroke is divided by the total stroke time. Load factor: ((Load weight x 9.8)/Theoretical force) x 100% Note) The Series CA1 has been changed to the Series CA2. Conditions 120-01 Average speed (mm/s) 800 700 600 00 400 00 200 100 0 Body ported Tube bore x Length Speed controller Silencer Series CJ2 Pressure 0. MPa Load factor 0% Stroke 60 mm Series CJ2 ø6 x 1 m AS201F-06 AN110-01 Series CM2 ø6 x 1 m AS01F-06 Series MB ø12 x 1 m AS4001F-12 AN200-02 Bore size Series CM2 Pressure 0. MPa Load factor 0% Stroke 00 mm Series MB, CA1 Note) Pressure 0. MPa Load factor 0% Stroke 00 mm ø6 ø10 ø16 ø20 ø2 ø2 ø40 ø40 ø0 ø6 ø80 ø100 214 204 286 10 2 10 98 60 64 60 60 8 01 47 487 749 79 610 22 86 22 17 160 120 160 160 120 160 160 Perpendicular, upward actuation Horizontal actuation 10 19 R N --
Series 000 Construction 2 position single 2 position double De-energized De-energized position closed center position closed center/exhaust center/pressure center De-energized De-energized position exhaust center position pressure center (This figure shows a closed center type.) Component Parts No. Description q Body w Piston plate e Piston r Spool valve t End cover y Spool spring Material Aluminum die-casted Resin Resin Aluminum, HNBR Resin Stainless steel Note Platinum silver Black Black painted Replacement Parts No. Description Material Part no. Note u Solenoid assembly Epoxy/Stainless steel DXT170-C- Common with i O-ring NBR 1 x 11 x 1 1 Series 000 --6
Port Solenoid Valve Body Ported Series 000 2 Position Single Grommet (G), (H) G 120- -01 H 120 Foot bracket G 120- -01-F (Mounting hole) H (Mounting hole for manifold) (Mounting hole) Manual override (Non-locking) G: 00 mm H: 600 mm R (PE port) (Piping port) N L plug connector (L) 120- L -01 M plug connector (M) 120- M -01 00 00 : With light/surge voltage suppressor DIN terminal (D) 120- D -01 MAX. 10 Applicable cable O.D. ø. to ø7 Built-in One-touch fittings 120- - C6 C8 C6: MAX. 6 C8: MAX. 6. 2-One-touch fitting (A, B port) Applicable tubing model C6: T0604 C8: T0806 --7
Series 000 2 Position Double 220 Grommet (G), (H) G 220- -01 H (Mounting hole for manifold) (Mounting hole) Manual override (Non-locking) G: 00 mm H: 600 mm (PE port) L plug connector (L) 220- L -01 (Piping port) M plug connector (M) 220- M -01 00 00 : With light/surge voltage suppressor DIN terminal (D) 220- D -01 MAX. 10 Built-in One-touch fittings 220- - C6 C8 2-One-touch fitting (A, B port) Applicable tubing model C6: T0604 C8: T0806 C6: MAX. 6 C8: MAX. 6. Applicable cable O.D. ø. to ø7 --8
Port Solenoid Valve Body Ported Series 000 Position Closed Center/Exhaust Center/Pressure Center 20 Grommet (G), (H) 420- -01 G H (Mounting hole for manifold) Manual override (Non-locking) 420 (Mounting hole) G: 00 mm H: 600 mm 20 R (PE port) N (Piping port) L plug connector (L) 420- L -01 00 M plug connector (M) 420- M -01 00 : With light/surge voltage suppressor DIN terminal (D) 420- D -01 Built-in One-touch fittings 420- -C6 C8 Applicable cable O.D. ø. to ø7 2-One-touch fitting (A, B port) Applicable tubing model C6: T0604 C8: T0806 C6: MAX. 6 C8: MAX. 6. --9
Series 000/Body ported Manifold Specifications Manifold Standard Manifold Specifications Model Manifold type P(SUP)/R(EXH) Valve stations 4(A), 2(B) port location 1(P), /(R) port Port size 4(A), 2(B) port Flow Characteristics Manifold Port size 1(P), /(R) port Type 20 Type 21 Single base/b mount Common SUP/Common EXH 2 to 1 stations 2 to 20 stations Valve Rc 1 8 Rc 1 4 Rc 1 8, C6, C8 2(B), 4(A) port V-20-01 1/8 1/8 2.2 0. V-20-C6 1/8 C6 1.4 0.2 V-20-C8 1/8 C8 1.7 0.8 2 V-21-01 1/4 1/8 2.1 0.6 V-21-C6 1/4 C6 1.4 0.2 V-21-C8 1/4 C8 1.8 0.7 Note) Value at manifold base mounted, 2 position single operating Flow characteristics 1 4/2 (P A/B) 4/2 / (A/B R) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv 0.7 2. 0.26 0. 0.7 2.0 0.2 0.49 0.4 2.1 0.2 0.1 0. 2. 0.26 0.4 0.6 2.1 0.24 0.0 0.0 2.1 0.20 0.0 Flat Ribbon Cable Manifold One-touch wiring to consolidate connection of external wires. Clean appearance The flat cable provides wiring on a printed circuit board to the individual valves at the manifold base, enabling the consolidation of external wiring at a touch through a 26 pins MIL connector. How to Order Manifold Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along with the manifold base model no. (Example) V-20-01 1 pc. (Manifold base) 120-G-012 pcs. (Valve) DXT199-22-1A1 pc. (Blanking plate assembly) Flat Ribbon Cable Manifold Specifications Model Manifold type P(SUP), R(EXH) Valve stations 4(A), 2(B) port location 1(P), /(R) port Port size 4(A), 2(B) port Applicable flat ribbon cable connector Internal wiring Applicable solenoid valve The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. Type 21P Single base/b mount Common SUP/Common EXH to 12 stations Valve Rc 1 4 Rc 1 8, C6, C8 Socket: 26 pins MIL, with strain relief (Conforming to MIL-C-80) +COM (For COM, please contact SMC separately.) 2- MOZ - - Rated voltage 100 VAC 0/60 Hz, 110 VAC 0/60 Hz, 24 VDC, 12 VDC Note) Withstand voltage specification of wiring unit part is equivalent to JIS C 0704 class 1. 1 6 01 C6 C8 Flow Characteristics Manifold V-21P-01 V-21P-C6 V-21P-C8 2 Port size 1(P), /(R) port 1/4 1/4 1/4 2(B), 4(A) port 1/8 C6 C8 Note) Value at manifold base mounted, 2 position single operating Flow characteristics 1 4/2 (P A/B) 4/2 / (A/B R) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv 2.1 0.6 0. 2. 0.26 0.4 1.4 0.2 0.6 2.1 0.24 0.0 1.8 0.7 0.0 2.1 0.20 0.0 --60 How to Order Manifold Instruct by specifying the valves, blanking plate assembly and connector assembly to be mounted on the manifold along with the manifold base model no. (Example) V-21P-071 pc. (Manifold base) 12-MOZ-C8 pcs. (Valve) 22-MOZ-C8 pcs. (Valve) DXT199-22-A 1 pc. (Blanking plate assembly) DXT192-2-1-4A pcs. (Connector assembly) DXT192-2-2-4A pcs. (Connector assembly) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc.
Port Solenoid Valve Body Ported Series 000 Common SUP/Common EXH Type 20 Type 21 4(A), 2(B) port 4(A), 2(B) port How to Order V 20 0 1 How to Order V 21 0 1 How to Order V Stations 02 2 stations 1 1 stations Stations 02 2 stations 20 21P 20 stations Stations 0 stations 12 0 12 stations P, R port thread type Nil Rc 00F G 00N NPT 00T NPTF Note) For more than 6 stations, supply air to both sides of P port and exhaust air from both sides of R port. Flat Ribbon Cable Type 21P 4(A), 2(B) port 1(P) port Rc 1/8 /(R) port Rc 1/8 1(P) port Rc 1/4 /(R) port Rc 1/4 1(P) port Rc 1/4 /(R) port Rc 1/4 P, R port thread type Nil Rc 00F G 00N NPT 00T NPTF P, R port thread type Nil Rc 00F G 00N NPT 00T NPTF Applicable solenoid valve G 2 - L 01 M -C6 D C8 Applicable blanking plate assembly DXT199-22-1A Applicable individual EXH spacer assembly DXT199-29-1A Note) For more than 10 stations, supply air to both sides of P port and exhaust air from both sides of R port. Applicable solenoid valve 1 01 2- MOZ - C6 6 C8 Applicable blanking plate assembly DXT199-22-A Applicable connector assembly DXT192-2-1- A (For 2 position single) DXT192-2-1- A (For 2 position double, position) 1: 100 VAC, : 110 VAC, 4: DC For How to order applicable connector assemblies, refer to page --7. Note) For more than 10 stations, supply air to both sides of 1(P) port and exhaust air from both sides of and (R) port. R N --61
Series 000 Option Combinations of Solenoid Valve, Manifold Gasket and Manifold Base Round head combination screw M x 1 ( With spring washer) Individual EXH Spacer Assembly DXT199-29-1A Round head combination screw M x 47 ( With spring washer) Installation of the 00 Valve on the 000 Manifold Use of an adaptor plate makes it possible to mount Series 00 on the manifold base of Series 000. The mounting direction is shown in the diagram below. Mount the solenoid so that it will be on the same side as the single solenoid of the Series 000. Gasket Individual EXH spacer Adapter plate assembly DXT201--1A Round head combination screw M x 1 ( ) With spring washer Applicable base V-20 V-21 V-21P 2-Rc 1/8 (EXH port) Gasket Gasket Applicable base V-20 V-21 Note) Please contact SMC when using an individual EXH spacer assembly, an individual or an adapter plate assembly on V-21P. Round head combination screw M x 10 ( ) With spring washer Adapter plate O-ring Blanking Plate Assembly DXT199-22-1A Round head combination screw M x 8 ( ) With spring washer Blanking plate DXT199-22-A Round head combination screw M x 8 ( With spring washer) Blanking plate Applicable base V-20 V-21 Gasket Applicable base V-20 V-21 Gasket Dust cap Applicable base V-21P Caution Mounting Screw Tightening Torques M: 0.8 N m --62
Port Solenoid Valve Body Ported Series 000 Grommet (G), (H) Type 20 Manifold V-20- Station 1 2n-Rc 1/8 (4(A), 2(B) port) (Pitch) 4-ø4. (Mounting hole) Manual override (Non-locking) G: 00 mm H: 600 mm 6-Rc 1/8 (1(P), /(R) port) PE port (Pilot EXH) R N (mm) Stations L1 L2 2 9 47 78 66 4 97 8 116 104 6 1 12 7 14 142 8 17 161 9 192 180 10 211 199 11 20 218 12 249 27 1 268 26 14 287 27 1 06 294 L plug connector (L) M plug connector (M) DIN terminal (D) Built-in One-touch fittings 00 00 MAX. 10 C6: MAX. 6 C8: MAX. 6. 2n-One-touch fitting (4(A), 2(B) port) Applicable tubing model C6: T0604 C8: T0806 Applicable cable O.D. ø. to ø7 : With light/surge voltage suppressor --6
Series 000 Type 21 Manifold V-21- Station 1 Grommet (G), (H) 2n-Rc 1/8 (4(A), 2(B) port) (Pitch) (Mounting hole) 6-Rc 1/4 (1(P), /(R) port) PE port Manual override (Non-locking) G: 00 mm H: 600 mm (mm) Stations 2 L1 66 8 L2 46 6 4 104 84 12 10 6 142 122 7 161 141 8 180 160 9 199 179 10 218 198 11 27 217 12 26 26 1 27 2 14 294 274 1 1 29 16 2 12 17 1 1 18 70 0 19 89 69 20 408 88 L plug connector (L) M plug connector (M) DIN terminal (D) Built-in One-touch fittings 00 00 MAX. 10 C6: MAX. 6 C8: MAX. 6. Applicable cable O.D. ø. to ø7 2n-One-touch fitting (4(A), 2(B) port) Applicable tubing model C6: T0604 C8: T0806 : With light/surge voltage suppressor --64
Port Solenoid Valve Body Ported Series 000 Type 21P Manifold V-21P- Station V-21P- Station Manual override (Non-locking) 2n-Rc 1/8 (4(A), 2(B) port) (Pitch) R (Mounting hole) 6-Rc 1/4 (1(P), /(R) port) (Light/Surge voltage suppressor) Triangle mark N (Station n)(station 1) Connector polarity indicator Applicable connector: 26 pins MIL (Conforming to MIL-C-80) Built-in One-touch fittings Stations 4 L1 88 108. 129 L2 68 109 109 6 149. 129. 7 170 10 8 190. 170. 9 211 191 10 21. 211. 11 22 22 (mm) 12 272. 22. C6: MAX. 6 C8: MAX. 6. 2n-One-touch fitting (4(A), 2(B) port) Applicable tubing model C6: T0604 C8: T0806 --6
Port Solenoid Valve Base Mounted Series 000 For details about certified products conforming to international standards, visit us at www.smcworld.com. Non plug-in 1 4 0 L 1 2 Type of actuation Type of actuation Body option Body option How to Order Rated voltage Electrical entry Plug-in 1 4 F Z 2 position single solenoid 2 position double solenoid 0: Individual exhaust for the pilot valve Light/Surge voltage suppressor Note) Manual override Port size Port size Thread type Nil: Without sub-plate Note) Please contact SMC in the case of without indicator light. Thread type Nil F N T Rc G NPT NPTF 01: Rc1 8 With sub-plate Note) R N position closed center (R) port PE port : Common exhaust type for main and pilot valve 02: Rc 1 4 With sub-plate position exhaust center (R) port PE port Note) (R1), (R2) port: Rc1 4 Manual override/plug-in type 4 position pressure center 1 2 4 6 9 Rated voltage 100 VAC, 0/60 Hz 200 VAC, 0/60 Hz 110 VAC, 0/60 Hz 220 VAC, 0/60 Hz 24 VDC 12 VDC Other Option Electrical entry Grommet L plug connector M plug connector DIN terminal G: Lead wire length 00 mm L: With lead wire (Length 00 mm) M: With lead wire MN: Without lead wire (Length 00 mm) D: With connector Nil: Non-locking push type Nil: Non-locking push type B: Locking type B (Slotted) Manual override/non plug-in type 1 0 B: Locking type B (Slotted) C: Locking type C (Manual) 1 0 C: Locking type C (Manual) H: Lead wire length 600 mm LN: Without lead wire LO: Without MO: Without DO: Without connector connector connector Light/Surge voltage suppressor Type LN, MN : With 2 sockets. Nil Z S None With light/surge voltage suppressor With surge voltage suppressor Not available for GZ, HZ and DOZ --67
Series 000 Applicable for cylinder actuation (up to ø0). Compact size (Width: 18 mm) Low power consumption: 1.8 W DC Specifications Fluid Operating pressure range (MPa) Ambient and fluid temperature ( C) Response time (ms) (1) (at the pressure of 0. MPa) Max. operating frequency (Hz) Effective area Manual override (2) Pilot exhaust 2 position single 2 position double position 2 position single, double position 2 position single, double position Lubrication Mounting orientation Impact /Vibration resistance (m/s 2 ) () Enclosure Air 0.1 to 0.7 0.1 to 0.7 0.1 to 0.7 10 to 0 C (No freezing. Refer to page -1-4.) 20 or less 0 or less 10 Refer to the table below. Non-locking push type, Locking slotted type, Locking lever type Individual pilot exhaust, Common exhaust (pilot and main valve) Common exhaust port for the pilot and main valve Not required Unrestricted 00/0 Dustproof Note 1) Based on dynamic performance test, JIS B 874-1981. (Coil temperature: 20 C, at rated voltage, without surge suppressor) Note 2) When operating the locking type manually, apply torque of 0.2 N m or less. Note ) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 4 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Refer to pages --74 to --84 for manifold use. Made to Order Specifications (For details, refer to page --8.) Solenoid Specifications Electrical entry AC 0/60 Hz Coil rated voltage (V) DC Allowable voltage fluctuation (%) Power consumption (W) (1) [Current ma] DC Apparent power (VA) [Current ma] (1) Surge voltage suppressor Indicator light AC Note 1) At rated voltage Note 2) Plug-in should be ZNR Inrush Holding Grommet (G)/(H), L plug connector (L), M plug connector (M), DIN terminal (D) 100, 200, 24, 48, 110, 220 24, 6, 12, 48 1 to +10% of rated voltage 1.8 (With indicator light 2.1) [24 VDC: 7 (With indicator light 87.)] 100 VAC: 4/0 Hz, 42/60 Hz 4./0 Hz, 4.2/60 Hz 200 VAC: 22./0 Hz, 21/60 Hz 100 VAC: /0 Hz, 0/60 Hz./0 Hz, /60 Hz 200 VAC: 17./0 Hz, 1/60 Hz DC: Diode, AC: ZNR (2) DC: LED (Red), AC: Neon bulb --68
Port Solenoid Valve Base Mounted Series 000 Flow Characteristics/Weight Valve model 40- -01 40- -02 Series 14 - -02 (Piping: ø6 x 1 m) 2 position position 2 position position Type of actuation Single Double Closed center Exhaust center Pressure center Single Double Closed center Exhaust center Pressure center Average speed (mm/s) 800 700 600 00 400 00 200 100 Port size 1,, (P, EA, EB) 4, 2 (A, B) Flow characteristics (1) 1 4/2 (P A/B) 4/2 / (A/B EA/EB) C [dm /(s bar)] 2. 1.9 b 0.4 0.6 Cv 0.7 0.48 C [dm /(s bar)] 2.8 2.1 b 0.7 0.46 Cv 0.71 0.7 1.2 0.48 0..4[1.] 0.6[0.7] 0.86[0.41].[0.8] 0.4[0.4] 0.78[0.2] 2.1 0.4 0.6 2. 1.9 1..6[0.8] 0.41 0.61 0.46 0.0 0.4 0. 0.2[0.] 0.84[0.2] Note 1) [ ]: Denotes the normal position. Exhaust center: 4/2 /, Pressure center: 1 4/2 Note 2) ( ): Without sub-plate. Cylinder Speed Chart Rc 1/8 Rc 1/8 Rc 1/4 Rc 1/4 2.9 2.2.7[1.4] 2.1 Use as a guide for selection. Please confirm the actual conditions with SMC Sizing Program. Bore size Series CA1 Note) The CA1 series has been changed to the CA2 series. Pressure 0. MPa Load factor 0% Stroke 00 mm ø40 ø0 ø6 ø80 ø100 Perpendicular, upward actuation Horizontal actuation 0. 0.74 0.44 0.60 0.27[0.6] 0.87[0.4] 0.47 0.8 Weight (g) Grommet 200(120) 240(160) 240(160) 200(120) 240(160) 240(160) (2) R N Speed controller/silencer AS01F- 02-06 /AN200-2 14 - -02 (Piping: ø8 x 1 m) 800 700 600 00 400 00 200 100 Perpendicular, upward actuation Horizontal actuation Speed controller/silencer AS01F- 02-08 /AN200-2 14 - -02 (Piping: ø10 x 1 m) 800 700 600 00 400 00 200 100 Perpendicular, upward actuation Horizontal actuation Speed controller/silencer AS01F- 02-10 /AN200-2 14 - -02 (Piping: ø12 x 1 m) 800 700 600 00 400 00 200 100 Perpendicular, upward actuation Horizontal actuation Speed controller/silencer AS4001F- 02-12 /AN200-2 It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open. The average velocity of the cylinder is what the stroke is divided by the total stroke time. Load factor: ((Load weight x 9.8)/Theoretical force) x 100% --69
Series 000 Construction 2 position single 2 position double position closed center position closed center/exhaust center/pressure center position exhaust center position pressure center (This figure shows a closed center type.) Component Parts No. Description q Body w Piston plate e Piston r Spool valve t End cover y Spool spring Material Aluminum die-casted Resin Aluminum, HNBR Resin Resin Stainless steel Note Platinum silver Black Black painted Replacement Parts No. Description Material Part no. Note u Sub-plate Aluminum DXT199-7-1 P Rc 1 8 die-casted DXT199-7-2 P Rc 1 4 i Solenoid assembly Epoxy/Stainless steel DXT170-C- o O-ring NBR 1 x 11 x 1 Common with 1 Series 000 Thread type Nil: Rc F: G N: NPT T: NPTF --70
Port Solenoid Valve Base Mounted Series 000 2 Position Single 140 Grommet (G), (H) 140- - 01 G H 02 G: 00 mm H: 600 mm Manual override (Non-locking) (PE port) (Mounting hole) -Rc 1/8, 1/4 (1(P), 4(A), 2(B) port) 2-Rc 1/4 ((R1), (R2) port) R N 02 00 L plug connector (L) 140- L -01 M plug connector (M) 140- M - 01 02 00 DIN terminal (D) 140- D - 01 02 Applicable cable O.D. ø. to ø7 MAX. 10 : With light/surge voltage suppressor --71
Series 000 2 Position Double 240 H 02 Manual override (Non-locking) (Mounting hole) G: 00 mm H: 600 mm (PE port) -Rc 1/8, 1/4 (1(P), 4(A), 2(B) port) 2-Rc 1/4 ((R1), (R2) port) 02 00 DIN terminal (D) 240- D - M plug connector (M) 01 240- M - 00 02 Grommet (G), (H) G 240- - 01 L plug connector (L) 01 240- L - MAX. 10 01 02 Applicable cable O.D. ø. to ø7 : With light/surge voltage suppressor --72
Port Solenoid Valve Base Mounted Series 000 Position Closed Center/Exhaust Center/Pressure Center 40 Grommet (G), (H) 4 G 40- -01 H 02 G: 00 mm H: 600 mm Manual override (Non-locking) (Mounting hole) 440 40 R L plug connector (L) 440- L - 01 00 02 (PE port) -Rc 1/8, 1/4 (1(P), 4(A), 2(B) port) 2-Rc 1/4 ((R1), (R2) port) M plug connector (M) 440- M -01 00 02 N DIN terminal (D) 440- D - MAX. 10 01 02 : With light/surge voltage suppressor Applicable cable O.D. ø. to ø7 --7
Series 000/Base Mounted Manifold Specifications Manifold Standard Manifold Specifications Model Manifold type P(SUP), R(EXH) Valve stations 4(A), 2(B) port Position porting specifications Direction 1(P), /(R) port Port size 4(A), 2(B) port Flow Characteristics Type 40 Type 41 Type 42 Single base/b mount Common SUP and EXH 2 to 20 Base Bottom Rc 1/8 Rc 1/4 Base Side 01(Rc 1/8) C6 (One-touch fitting for ø6) C8 (One-touch fitting for ø8) B7 (One-touch fitting for 1/4") C9 (One-touch fitting for /16") Port size Flow characteristics Manifold 1(P), /(R) 2(B), 4(A) 1 4/2 (P A/B) 4/2 / (A/B R) port port C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv V-40 1/4 1/8 2.1 0.28 0.1 2. 0.2 0.9 V-41 1/4 1/8 2.0 0.0 0.0 2.2 0.0 0. 4 V-42-C6 1/4 C6 1. 0.2 0.8 2.2 0.2 0.2 V-42-C8 1/4 C8 1.9 0.24 0.46 2.2 0.26 0. Note) Value at manifold base mounted, 2 position single operating How to Order Manifold Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along with the manifold base model no. (Example) V-41-01-01 1 pc. (Manifold base) 140-G2 pcs. (Valve) DXT199-22-1A 1 pc. (Blanking plate assembly) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. DIN Rail Manifold Manifold Specifications Manifold type P(SUP), R(EXH) Valve stations 4(A), 2(B) port Porting specifications Port size Model Position Direction 1(P), /(R) port 4(A), 2(B) port Connector Internal wiring Note) It is available at +COM or COM. Type 4 Stacking type non plug-in type Common SUP and EXH 2 to 20 Base Side C10 (One-touch fitting for ø10) C6 (One-touch fitting for ø6) C8 (One-touch fitting for ø8) MIL-C-2408 JIS-X-101 Type 4F Stacking type plug-in type Applicable for D-sub connector COM Note) Flow Characteristics V-4 Manifold 4 Port size 1(P), /(R) port C10 C10 2(B), 4(A) port C6 C8 Note) Value at manifold base mounted, 2 position single operating Flow characteristics 1 4/2 (P A/B) 4/2 / (A/B R) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv 1. 0.1 0.8 2.2 0.17 0.2 2.1 0.26 0.1 2.2 0.1 0.2 How to Order Manifold Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along with the manifold base model no. (Example) V-4FD-06-C8C 1 pc. (Manifold base) 14-FZ 2 pcs. (Valve) 24-FZ pcs. (Valve) 000-6-1A 1 pc. (Blanking plate assembly) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. --74
Port Solenoid Valve Base Mounted Series 000 Common SUP/Common EXH Type 40 1(P) port Rc 1/4 /(R) port Rc 1/4 Type 41 4(A), 2(B) port Rc 1/8 Type 42 4(A), 2(B) port C6, C8 DIN Rail Manifold Common SUP/Common EXH Type 4 (Non plug-in type) How to Order Type 4F (Plug-in type) 4(A), 2(B) port Rc 1/8 1(P) port Rc 1/4 /(R) port Rc 1/4 1(P) port Rc 1/4 /(R) port Rc 1/4 V Stations 02 20 2 stations How to Order How to Order V 40 0 2 01 20 20 stations Note) For more than 10 stations, supply air to both sides of 1(P) port and exhaust air from both sides of and (R) port. How to Order How to Order Stations 02 2 stations 4(A), 2(B) Port size 01 Rc1 8 V 41 0 1 01 4(A), 2(B) Port size 01 Rc1 8 Note) For more than 8 stations, supply air to both sides of P port and exhaust air from both sides of R port. 20 stations V 42 0 1 C6 02 20 P, R port thread type Nil Rc F G N NPT T NPTF P, R port thread type Nil F N T Rc G NPT NPTF C6 A, B port size One-touch fitting for ø6 P, R port thread type C8 One-touch fitting for ø8 Nil Rc B7 One-touch fitting for 1/4" F G B9 One-touch fitting for /16" N NPT T NPTF Note) For more than 8 stations, supply air to both sides of 1(P) port and exhaust air from both sides of and (R) port. 4 0 D C8 SUP/EXH block mounting position Symbol Position Applicable stations U U side 2 to 10 stations D D side 2 to 10 stations B Both sides 2 to 20 stations M Special Special specifications specifications For special specifications, indicate separately by the manifold specification sheet. Connector mounting direction Symbol Mounting direction Applicable stations U U side 2 to 10 stations D D side B Both sides 11 to 10 stations Stations 02 SUP/EXH block mounting position 2 stations For 2 to 10 stations : One side 20 20 stations Nil (Same as direction of connector mount) For 11 to 20 stations: Both sides V 02 20 Stations Stations 2 stations 20 stations 2 stations 20 stations C 4 (A), 2 (B) port size One-touch C6 fitting for ø6 One-touch C8 fitting for ø8 M Mixed In the case of mixed specifications (M), indicate separately on the manifold specification sheet. 4F D 0 C8 B For 2 to 10 stations: Both sides M Special specifications For special specifications, indicate separately by the manifold specification sheet. 4(A), 2(B) port size C6 C8 M C One-touch fitting for ø6 One-touch fitting for ø8 Mixed Applicable solenoid valve G 4 - L M D Applicable blanking plate assembly DXT199-22-1A Applicable individual EXH spacer assembly DXT199-29-2A Applicable individual SUP spacer assembly DXT199--1A Applicable interface regulator ARBZ000-00-P G 4 - L M D Applicable blanking plate assembly 000-6-2A DIN rail length specified Nil Standard length For stations (Specify a longer rail than the 20 For 20 stations standard length.) In the case of mixed specifications (M), indicate separately on the manifold specification sheet. Applicable solenoid valve 4- FZ Applicable blanking plate assembly 000-6-1A DIN rail length specified Nil 20 Applicable solenoid valve Standard length For stations (Specify a longer rail than the For 20 stations standard length.) --7 R N
Series 000 Option/Standard Manifold Combinations of Solenoid Valve, Manifold Gasket and Manifold Base Round head combination screw Individual EXH Spacer Assembly DXT199-29-2A Round head combination screw M x 1 M x 47 ( With spring washer ) ( With spring washer) Installation of the 00 Valve on the 000 Manifold Use of an adaptor plate makes it possible to mount Series 00 on the manifold base of Series 000. The mounting direction is shown in the diagram below. Mount the solenoid so that it will be on the same side as the single solenoid of the Series 000. In the case of base mounting, 2(A) port of port valve should be 2(B) port of manifold base. Applicable base V-40 V-41 V-42 Blanking Plate Assembly DXT199-22-1A DXT199--1A Applicable base V-40 V-41 V-42 Individual SUP Spacer Assembly Round head combination screw M x 47 ( With spring washer) Gasket Round head combination screw M x 8 ( ) With spring washer Blanking plate Gasket 2-Rc 1/8 (EXH port) Applicable base V-40 V-41 V-42 Interface Regulator (P port regulation) Interface style regulators can be placed on top of the manifold base to reduce the pressure of each of the valves. ARBZ000-00-P Round head combination screw With spring ( washer ) Individual EXH spacer Gasket Adapter Plate Assembly DXT201--2A Round head combination screw M x 8 ( ) With spring washer Round head combination screw DXT199-2-1 M x 1 With spring washer ( ) Round head combination screw M x 10 ( With spring washer) Adapter plate Gasket Applicable base V-40 V-41 V-42 Series 00 Base mounted Gasket Rc 1/8 (SUP port) Applicable base V-40 V-41 V-42 Individual SUP spacer Gasket Before using, refer to page --8. Applicable base V-40 V-41 V-42 Caution Mounting Screw Tightening Torques M: 0.8 N m --76
Port Solenoid Valve Base Mounted Series 000 Option/DIN Rail Manifold Blanking Plate Assembly 000-6-2A 000-6-1A Round head combination screw M x 8 ( With spring washer ) Blanking plate Manifold gasket Applicable base V-4 Round head combination screw M x 8 ( With spring washer) Blanking plate Combination of Solenoid Valve, Gasket and Manifold Base Round head combination screw M x 1 ( With spring washer ) Manifold gasket Applicable base V-4 SUP Block Disk By installing a SUP block disk in the pressure supply passage of a manifold valve, it is possible to supply two or more different high and low pressures to one manifold. 000-68-1A 000-68-1A Round head combination screw M x 1 ( With spring washer ) Manifold gasket Applicable base V-4F EXH Block Disk By installing an EXH block disk in the exhaust passage of a manifold valve, it is possible to divide the valve s exhaust so that it does not affect another valve. R N Manifold gasket Applicable Plug Assembly (D-sub connector cable assembly) Dust cap Cable length 1. m m m 8 m For details, refer to page --8. Assembly part no. V000-21A-1 V000-21A-2 V000-21A- V000-21A-4 Component parts Plug MIL standard D-sub connector Number of terminals: 2 Cable: 2 cores x 0. mm 2 Applicable base V-4F Caution Mounting Screw Tightening Torques M2.: 0.2 N m (For stacking type manifold) --77
Series 000 Exploded View/DIN Rail Manifold Type 4 Manifold r w U side r q e w (a) Bolt (Both sides) e (b) Lever D side Replacement Parts No. Description Part no. q Manifold block assembly 000-0A-2- w SUP/EXH block assembly 000-1A-2 e End block assembly 000-2A-2D r End block assembly 000-2A-2U C6 C8 Note C6: A, B port with One-touch fitting for ø6 C8: A, B port with One-touch fitting for ø8 P/R port with One-touch fitting for ø10 For D side For U side DIN rail (a) Bolt (Both sides) How to Increase Manifold Base (1) Loosen (both) bolts (a), which are securing the manifold onto the DIN rail, 1 to 2 turns. (To remove the manifold base from the DIN rail, loosen the bolts 4 to turns.) (2) Press lever (b) to disconnect the manifold block assembly at the location in which you wish to place an additional manifold block assembly. (However, there are no levers between q and r or between e and r. They can be disconnected by merely pulling them apart.) () Mount additional manifold block assembly on the DIN rail as shown in the Fig. (2). (4) Press the block assemblies and tighten the bolts (a) to fix them to the DIN rail. Note) When there are 10 or fewer manifold block assemblies, and more are added to make a total of 11 or more, a supply/exhaust block assembly must also be added. Fig. (1) Fig. (2) Station expansion is possible at any position. (a) Bolt (Both sides) Hook this part onto the DIN rail, and press down in the direction of the arrow. (b) Lever --78
Port Solenoid Valve Base Mounted Series 000 Exploded View/DIN Rail Manifold Type 4F Manifold u e i t U side (b) Lever q y R Replacement Parts No. q w e r t y u i Description Manifold block assembly SUP/EXH block assembly SUP/EXH block assembly End block assembly End block assembly End block assembly End block assembly SUP/EXH block assembly Location of addition Part no. 000-0A-1-000-1A-1D 000-1A-1U C6 C8 000-2A-2D 000-2A-1U 000-2A-1D 000-2A-2U 000-1A-1M (b) Lever Note C6: A, B port with One-touch fitting for ø6 C8: A, B port with One-touch fitting for ø8 For D side, With D-sub connector and P/R port with One-touch fitting for ø10 For U side, With D-sub connector and P/R port with One-touch fitting for ø10 For D side, set with w For U side For D side For U side, set with e Without D-sub connector, For indicated location P/R port with One-touch fitting for ø10 w DIN rail r (a) Bolt (Both sides) (a) Bolt (Both sides) D side N How to Increase Manifold Base (1) Loosen (both) bolts (a), which are securing the manifold onto the DIN rail, 1 to 2 turns. (To remove the manifold base from the DIN rail, loosen the bolts 4 to turns.) (2) Using a flat screwdriver, press lever (b) to disengage the link of the manifold block assembly on the U side or the D side from the SUP/EXH block assembly or from the end block assembly. (However, there are no levers between t and q. They can be disconnected by merely pulling them apart.) () Remove the housing cover from the D-sub connector portion of the SUP/EXH block assembly. (Refer to Fig. (1).) (4) Following the procedure shown in Fig. (2), mount the manifold block assembly to be added onto the DIN rail. As shown in Fig. (), insert the pin of the lead wire assembly into the D-sub connector, and attach the round crimped terminal to the screw that connects the wires. () Press the block assemblies and tighten the bolts (a) to fix them to the DIN rail. Note) When there are 10 or fewer manifold block assemblies, and more are added to make a total of 11 or more, a supply/exhaust block assembly must also be added. To add a manifold block assembly, add it to the U side so that the terminal number of the D-sub connector and the valve link position will be in accordance with the circuit diagram. Fig. (1) Black White Lead wire ass'y Housing cover D-sub connector Hook Pin After inserting the pin, lightly pull on the lead wire to verify the lock. (b) Lever Fig. () How to insert lead wire assembly pin Stations Housing side Connector terminal no. U side D side Fig. (2) 1 station (11 stations) 2 station (12 stations) station (1 stations) 4 station (14 stations) station (1 stations) 6 station (16 stations) 7 station (17 stations) 8 station (18 stations) 9 station (19 stations) 10 station (20 stations) Hook this part on to the DIN rail and press down until a click is heard. Terminal no. B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil Lead wire color Black White Black White Black White Black White Black White Black White Black White Black White Black White Black White Red Red --79
Series 000 Type 40 Manifold: Bottom Ported V-40- Station 2-01 Grommet (G), (H) (Mounting hole) 6-Rc 1/4 (1(P), /(R) port) Manual override (Non-locking) G: 00 mm H: 600 mm PE port (Pilot EXH) 2n-Rc 1/8 (4(A), 2(B) port) (Pitch) (mm) Stations 2 L1 66 8 L2 46 6 4 104 84 12 10 6 142 122 7 161 141 8 180 160 9 199 179 10 218 198 11 27 217 12 26 26 1 27 2 14 294 274 1 1 29 16 2 12 17 1 1 18 70 0 19 89 69 20 408 88 L plug connector (L) M plug connector (M) DIN terminal (D) Applicable cable O.D. ø. to ø7 00 MAX. 10 00 : With light/surge voltage suppressor --80
Port Solenoid Valve Base Mounted Series 000 Grommet (G), (H) Type 41 Manifold: Side Ported V-41- Station 1-01 Manual override (Non-locking) PE port (Pilot EXH) 6-Rc 1/4 (1(P), /(R) port) (Mounting hole) R (Pitch) G: 00 mm H: 600 mm N Stations 2 L1 78 98 L2 0 70 4 118 90 18 110 6 18 10 2n-Rc 1/8 (4(A), 2(B) port) 7 178 10 8 198 170 9 218 190 10 28 210 11 28 20 12 278 20 1 298 270 14 18 290 1 8 10 16 8 0 17 78 0 18 98 70 19 418 90 (mm) 20 48 410 L plug connector (L) M plug connector (M) DIN terminal (D) 00 00 MAX. 10 Applicable cable O.D. ø. to ø7 : With light/surge voltage suppressor --81
Series 000 Type 42 Manifold: Side Ported V-42- Station 1- C6 C8 Grommet (G), (H) Manual override (Non-locking) PE port (Pilot EXH) 6-Rc 1/4 (1(P), /(R) port) (Pitch) (Mounting hole) 2n-One-touch fitting (4(A), 2(B) port) Applicable tubing model C6: T0604 C8: T0806 G: 00 mm H: 600 mm C6: MAX. 6 C8: MAX. 6. (mm) Stations 2 L1 77 96 L2 49 68 4 11 87 14 106 6 1 12 7 172 144 8 191 16 9 210 182 10 229 201 11 248 220 12 267 29 1 286 28 14 0 277 1 24 296 16 4 1 17 62 4 18 81 19 400 72 20 419 91 L plug connector (L) M plug connector (M) DIN terminal (D) 00 00 MAX. 10 Applicable cable O.D. ø. to ø7 : With light/surge voltage suppressor --82
Port Solenoid Valve Base Mounted Series 000 Grommet (G), (H) U side Stations L1 L2 L L4 DIN rail DIN rail holding screw 2 12 112. 97 1 148 17. 116 16 4 160. 10 1 1 L plug connector (L) Type 4 DIN Rail Manifold (Non Plug-in): Side Ported V-4- Station D- C6C C8C 2n-One-touch fitting (A, B port) Applicable tubing model (Pitch) C6: T0604 C8: T0806 Manual override (Nonlocking) (Rail mounting hole pitch 12.) (Station n) (Station 1) 18. 17 14 16 Separation lever 6 198 187. 17 12. 7 22 212. 192 1. 8 2. 22 211 12. M plug connector (M) One-touch fitting (P, R port) Applicable tubing model D side G: 00 H: 600 9 260. 20 20 1. (mm) 10 27 262. 249 12 DIN terminal (D) V-4- Station B- C6C C8C V-4- Station U- C4C C6C (Pitch) (mm) Stations 2 4 6 7 8 9 10 L1 148 160. 18. 198 22 2. 260. 27 298 L2 17. 10 17 187. 212. 22 20 262. 287. L 116 1 14 17 192 211 20 249 268 L4 16 1 16 12. 1. 12. 1. 12 1 (mm) Stations 11 12 1 14 1 16 17 18 19 20 L1 10.. 48 7 8. 410. 42 448 47 48. L2 00 2 7. 62. 7 400 412. 47. 462. 47 L 287 06 2 44 6 82 401 420 49 48 L4 12 1 11. 14. 11. 14. 11 14 17 14 (Pitch) R N 00 00 MAX. 10 Applicable cable O.D. ø. to ø7 Stations L1 L2 L L4 2 12 112. 97 1 4 6 148 160. 18. 198 17. 10 17 187. 116 16 1 1 14 16 17 12. (mm) 7 8 9 10 22 2. 260. 27 212. 22 20 262. 192 1. 211 12. 20 1. 249 12 --8
Series 000 Type 4F DIN Rail Manifold (Plug-in): Side Ported V-4FD- Station - C6C C8C 2n-One-touch fitting (A, B port) Applicable tubing model (Pitch) C6: T0604 C8: T0806 One-touch fitting port (P, R port) Applicable tubing model: T107 U side D side DIN rail DIN rail holding screw V-4FU- Station - C6C C8C Manual override (Non-locking) (Rail mounting hole pitch 12.) (Station n)(station 1) Separation lever (Push type) D side connector Terminal no. 1 Stations L1 L2 L L4 JIS-X-101 Applicable connector D-SUB { MIL-C-2408} 2 12 112. 97 1 148 17. 116 16 4 160. 10 1 1 18. 17 14 16 6 198 187. 17 12. 7 22 212. 192 1. 8 2. 22 211 12. 9 260. 20 20 1. C6C V-4F U D- Station B- C8C (2 to 10 stations) C6C V-4FB- Station - C8C (11 to 20 stations) (Pitch) (Pitch) (mm) 10 27 262. 249 12 Stations L1 L2 L L4 2 12 112. 97 1 148 17. 116 16 4 160. 10 1 1 18. 17 14 16 6 198 187. 17 12. 7 22 212. 192 1. 8 2. 22 211 12. 9 260. 20 20 1. (mm) 10 27 262. 249 12 Stations L1 L2 L L4 Stations L1 L2 L L4 2 148 17. 116 16 11 10. 00 287 12 160. 10 1 1 12. 2 06 1 4 18. 17 14 16 1 48 7. 2 11. 198 187. 17 12. 14 7 62. 44 14. 6 22 212. 192 1. 1 8. 7 6 11. 7 2. 22 211 12. 16 410. 400 82 14. 8 260. 20 20 1. 17 42 412. 401 11 9 27 262. 249 12 18 448 47. 420 14 (mm) 10 298 287. 268 1 19 47 462. 49 17 (mm) 20 48. 47 48 14 --84
Series Made to Order Specifications: Please contact SMC for detailed specifications, dimensions, and delivery. 1. Solenoid Valve: External Pilot Specifications Applicable solenoid valve series 000/000 (Non plug-in type only) Model no. 0 ( ) X20 Specifications Entry is the same as standard products. Operating pressure Main pressure range (MPa) External pilot pressure Pilot exhaust method Dimensions 000: 8 mm longer 000: 8 mm longer 100 kpa to 0.7 0.1 to 0.7 Pilot valve individual exhaust JIS Symbol Body ported 2 position single position closed center R N 2 position double position exhaust center position pressure center --8