INSTRUCTIONS. E46 325, 330 with C38 blower MS45 & MS43

Similar documents
INSTRUCTIONS E36 SUPERCHARGER WITH C38 BLOWER.

Installation manual BMW E TS1/TS2

Procharger Stage II Intercooled Supercharger System (11-14 GT)

Always wear safety glasses when working on your vehicle.

Phone Fax

MAZDASPEED3 Intercooler Instructions

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side

2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit

Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions

Slingshot Rotrex Supercharger Kit

Instant Chat off the main page of Or simply call our tech team at

3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT

Scion FR-S ZN6. GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N #

INSTRUCTIONS. INTERCOOLER UPGRADE BMW E82 135i 2008-

Turner M50 Manifold Adapter Install. April 26, 2012

Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI

v Porsche 928

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler

NISSAN 350Z 300HP ENGINE INTERCOOLED SUPERCHARGER INSTALLATION INSTRUCTIONS

SLP Camaro ZL1 STAGE 3 (650 HP)

2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED

Fizzle Intercooler Kit Installation Instructions

G2 INSTALLATION MANUAL

2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing

The M7 Direct Flow Intercooler (DFIC) Installation Guide

407500_ 2000 Maxima SC.doc rev.07/31/01 Page 1 of 15

ENGINE DEVELOPMENT INC.

VR6 Supercharger System Golf III and Jetta III VR6 Installation Manual Model Year

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D

INFINITI G35 298HP ENGINE INTERCOOLED SUPERCHARGER INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS STILLEN SUPERCHARGER KIT Nissan 350Z P/N &

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION

05-08 GT. Hellion Power Systems Mustang Kit Instructions

All cores due 30 days after invoice date - no credit after 60 days.

BLACKBIRD INSTALLATION SUPPLEMENT

IAG Street Series Air / Oil Separator (AOS) For 2017 WRX

B6-B7 S4 Supercharger Install instructions

WARNING: IF YOU ARE NOT EXPERIENCED IN THE AREA OF AUTOMOTIVE MECHANICS WE STRONGLY URGE THAT YOU REFER THIS INSTALLATION TO YOUR MECHANIC.

BLACKBIRD INSTALLATION SUPPLEMENT

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler

Edelbrock E-Force Supercharger Part #1538: Dodge 1500 Truck 5.7L V8 HEMI

TOYOTA SEQUOIA MY SUPERCHARGER FIT KIT Preparation

INTERCOOLED SUPERCHARGER SYSTEM FORD 5.4L 3V F-150 TRUCK

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92/E93 335i/xi with stock oil cooler

SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.

INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT

2012 NISSAN 370Z / NISMO INTERCOOLED SUPERCHARGER INSTALLATION INSTRUCTIONS

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS

Charger, Magnum, 300C 5.7L & 6.1L Supercharger Installation Manual

Installation Instructions

RZR SUPERCHARGER KIT INSTALLATION INSTRUCTIONS POLARIS RZR 1000 SUPERCHARGER KIT. 1 of 33

INSTALLATION MANUAL BULLET PROOF OIL COOLER KIT F-SERIES

Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM

03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions

SHELBY GT500

INSTALLATION INSTRUCTIONS

IAG Air / Oil Separator (AOS) For STi

Official Powerdyne Model BD Supercharger and Kit Limited Warranty

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L)

Revised 10/23/2015 Page 2 of 10

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #

ESS INSTALL. The donor car /6 Cosmos Black/Sand UUC Short Shifter Brembo cross drilled rotors Phillips Nav System 16:9

LChevrolet Camaro Supercharger Kit

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo

IAG Street Series Air / Oil Separator (AOS) For WRX

2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit INSTALLATION GUIDE FOR RACING USE ONLY

SL63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2

Included parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/ Hardware STEP 1

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D

2015 WRX Engine Oil Cooler

#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS

Revised 10/22/2014 Page 2 of?

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler

List of parts needed below. Tools needed

BLACKBIRD INSTALLATION SUPPLEMENT

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L)

Shotgun Single Barrel HPFP install guide

Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM

TOYOTA FJ CRUISER MY SUPERCHARGER FIT KIT Preparation

Instructions for: Toyota 5.7L Coupler Replacement

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L

Edelbrock Hemi Supercharger Part #1530, 1531, 1532, 1533, 1536 & 1537

Steeda S197 Mustang Whipple Supercharger Drive

2015 Corvette Supercharger System Instructions

TOYOTA FJ CRUISER MY SUPERCHARGER FIT KIT Preparation

ITEM QTY CHECK PART NUMBER DESCRIPTION

Shotgun Double Barrel HPFP install guide

CLS63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions

03-04 Cobra. Hellion Power Systems Mustang Cobra Kit Instructions

Tools Required. Metric Wrench Set Screwdriver Set Metric Socket Set Pliers Heavy duty hydraulic Jack and Car Stands Box knife or similar Hacksaw WD40

Cylinder head/gasket, replacing

INSTRUCTION. INTERCOOLER UPGRADE BMW E92 335i

LML 3 Y-Bridge Kit or High Flow Intake Bundle Package

Tork Tech Inc. Customer Service , Sales

INSTALLATION INSTRUCTIONS

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler

BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).

Edelbrock E-Force Supercharger Complete Competition Ford Mustang 5.0L Part # s: 15896

Factory safe air/fuel ratio s for Optimum performance Patent# 7,359,795 Now equipped with Air Fusion

Transcription:

INSTRUCTIONS E46 325, 330 with C38 blower MS45 & MS43 1

Introduction Congratulations on your purchase of an Active Autowerke Supercharger, and welcome to the AA Tuning family. Your supercharger kit was developed to provide a level of driving enjoyment that cannot be matched. Enclosed in this packet you will find general guidelines, recommended maintenance schedules and detailed installation instructions for your supercharger. Please read all the material thoroughly and become familiar with our recommendations. If anything is unclear or ambiguous, please do not hesitate to contact us for further clarification. We are here to help. Operating Instructions for AA supercharged cars Always allow your engine and supercharger to warm up for at least one minute before placing the car in gear. In colder weather (below 50 degrees Fahrenheit), we recommend at least two-to-three minutes of warm-up time. Always use the best fuel (93 octane) available. If 91 octane is the only available fuel, add an octane booster if you detect any knocking. Active Autowerke calibrates the software to operate on 91 octane, but some cars may experience slight knocking or detonation. Excessive knocking will damage the motor, so pay close attention to any hint of knocking. On Steptronic or automatic transmission models, we recommend that the transmission be set in Sport mode when the car is driven hard. This will allow the transmission to shift more quickly to prevent any excess slippage. Additionally, after driving hard in an automatic-equipped car, you should allow the car to cool off for at least one minute before shutting off the motor. This will allow your transmission fluid to cool off. It is also a good idea to follow this procedure in order for the supercharger to cool off properly. SUPER CHARGER SYSTEMS ARE NOT RECOMMENDED FOR AUTOMATIC CARS DUE TO THE TORQUE INCREASE. IT CAN BURN OUT THE TRANSMISSION. CUSTOMERS ARE AT THEIR OWN RISK. Following these recommendations will ensure that your supercharger provides many miles of thrilling driving enjoyment. If you have any questions, please e-mail or call us. E-mail: aatuning@activeautowerke.com Phone: 305-233-9300 2

E46 C38 Blower (PARTS VARY ACCORDING TO MODEL) 3

INSTRUCTIONS BMW E46 with C38 Blower AA Supercharger System DISMANTLE Disconnect negative side of battery. Disconnect battery cable from starting block on passenger fender. Remove stock air box. Remove Micofilter housing and filter. Unclip power wire housing from Microfilter frame. Remove front cowling 4

Remove cowling around brake booster, this will give more space to remove intake. Take the brake line out of the booster to make removing the cowl easier. Remove electric fan. Remove fuel injector cover Remove steering reservoir with bracket to get access to the oil separator line. The steering reservoir bracket needs to be replaced with a newly modified one. 5

Remove Desa from intake this will make it easier to get to the clamps on the Air Mass boot. Remove Air Mass meter and boot. Pull aside Purge valve. Remove Purge valve bracket, to get access to the oil separator line. Remove the air shroud from the intake manifold. You may have to pry the shroud up. Lubricate O rings before putting back. 6

Pull up on the shroud until the oil separator hose is exposed. Use a sharp razor blade to slice hose. Slice the hose so it separates from the shroud rail. Cap off the end of the shroud were the oil separator line was removed. Use the ½ inch plug and clamp provided. Pull the oil separator line through the bottom of the manifold where the purge valve was located. Twist the line counter clockwise to release the end from the oil separator. Slice off connector from the oil plastic line. 7

View of the oil separator. Install connector into one end of 2 ft long 16x22mm hose. Depending on how you route the hose you may have to trim off any excess length, after you install the snail pipe. Make sure the hose is not kinked. Slide the hose and connector back onto the oil separator and twist hose clockwise till the connector locks. Pull on hose and make sure the connection is secure, will cause oil leak if it is not properly connected. Install back purge valve bracket and bend hose towards driver s fender. Careful not to kink hose. 8

Separate the rubber line from the plastic tubing of the purge valve line. In some cases you may have to cut the rubber and or the plastic line to separate them. Install grey valve with arrow towards the engine. Slide the 6mm vacuum line over the plastic tubing and then the brass fitting into the rubber line. Install back air shroud rail. Lubricate O rings so that the rail slides back in easier. A special adjustable brace is supplied with the kit. On some cars the alternator mounts may be uneven due to deviations in the castings. This brace can be adjusted to compensate for any belt alignment problems which may cause belt noise. 9

Install blower rear brace before going any further. This is much easier with the steering reservoir out and the blower off. Install bracket to mounting bolt on oil filter head. 10

Install turn buckle on the out side of oil filter head bracket. Leave other end free until blower is installed. Remove steering cooler bracket and replace with the one supplied. New steering reservoir bracket only has one leg. 11

Install steering reservoir into bracket then use 17mm tall spacer and bolt to lift up the reservoir assembly. After the blower is installed, make sure there is adequate clearance between blower and reservoir. You may have to pull aside reservoir to adjust and tighten blower brace after the blower is installed. On the back of the intake manifold, take off the rubber plug to expose vacuum nipple. Slide on vacuum line provided for the blow off valve. 12

Install 45 degree 3 inch elbow to throttle body. Slightly face the hose down. Make sure the hose is securely connected to the throttle. Pull hard on the hose to test. Siphon out the steering fluid from the reservoir. The line to the steering cooler needs to be extended so that the blower bracket can fit. Cut the line about half way and insert extension tube. Clamp the ends. This will enable the bracket to be installed with out stretching the line. 13

Remove A/C uni-belt from engine. Both belts are automatically tensioned via tensioner pulleys -On each pulley, the center is covered with a plastic cap. Using a small screwdriver, pry off cap to expose the hex key or bolt in the middle. Use 8mm Allen key to rotate tensioner pulley and take off belt. Remove idler pulley and tensioner assembly. Make sure to remove tensioner shock with assembly. You may have to remove the actual pulley first to get to one of the three bolts that hold the assembly. A new tensioner using no shock will replace the original set up. -Do not use the long 8x50mm bolt. Use back the original 8x35mm bolt and a new 8x35mm bolt & washer supplied with the new revised tensioner. Install new tensioner. 14

Remove the top alternator bolt 10x150. Remove the bottom alternator bolt 10x160mm. These will not be used back. Mount blower to bracket, before installing bracket to engine. If you mount the bracket to the engine first you will not be able put in the left lower mounting bolt for the blower. Mount the top idler pulley; make sure the spacer sleeve is installed into the bearing. See picture below. Make sure to use the bolt with the smallest head (button head) behind the pulley, so that it is countersunk in the bolt hole. Tighten bolts to 12 ft lbs. Mount the bottom idler pulley by first placing the spacer behind the pulley. The ridge on the spacer must sit inside the pulley. Use the 10x35mm Allen bolts and torque down to 18 ft lbs. Mount the 130mm bevel bolt in the top hole of bracket. Mount the 160mm bevel bolt in the bottom hole. Mount bracket to alternator and snug down bolts. On some cars you may be able to mount the bracket and then slide in the bolts, depending on proximity of the radiator. Put Never Seize or grease on bolts and torque to 12 ft lbs. 6mm Allen head bolts can strip easily because of the length. 15

Mount 6pkx2289mm belt by using 16mm socket to rotate tensioner and lock with suitable pin. Route belt as per diagram then pull out pin to release tensioner. It is usually easier to put the belt over the tensioner pulley last. After blower installation still leave the steering bottle loose so that you can get to the Turn buckle (SC brace) to adjust it. Mount bracket under clamps, some installers mount under one clamp or even add a third clamp on top of the 2 existing ones. Do not tighten till bar is inserted between both brackets. Insert the adjustable bar and try to position the assembly as straight as possible. Lock clamps and tighten the brackets to the bar. Bracket can be flipped around on some models, where by the slotted arm is against the blower. 16

Adjust bar till it puts pressure on blower then turn it an extra quarter turn and lock. If the belt makes noise adjust bar till the noise stops and lock in that position. Final adjustment will have to be done when car is running. MAKE SURE NOT TO OVER COMPENSATE WITH ADJUSTMENT THIS COULD CAUSE PREMATURE WEAR ON BELT. Install Blowoff valve pipe into the throttle hose. Rotate so that the Blowoff valve will be aligned with the Snail pipe outlet. Do not tighten clamp yet. Install 90 degree 2.5 inch rubber elbow with clamps. Slide onto Blowoff valve pipe first, then rotate onto the blower outlet. Do not tighten clamps yet. Optional: If Water Injection is being used install nozzle now and connect hose. 17

Install the Blowoff valve with 6x20mm bolts, nuts and gasket provided. Use Snail pipe and align Blowoff valve with the back of the blower. Blowoff valve also has to leave enough clearance to put back the Desa. Check to see if Desa will go back in. You may have to put some pressure on the Blowoff valve towards the fender to get adequate clearance. Remove back Desa. Now tighten the clamps to the throttle and blower. 18

Install idle valve hose. Hose goes from idle valve to blowoff valve pipe. Install clamps on the back of the blower and the blowoff valve. Leave loose. Slide the blowoff outlet of the snail pipe into the hose on the blowoff valve first. Then try to slide on the blower side. Using a hose tool slide the hose around the snail pipe. 19

Adjust the snail pipe till it is properly aligned. Slant the snail pipe so that the air filter and HFM point down behind the head light. Attach Oil separator hose and clamp. Cut hose for proper fitment. Install 6mm vacuum line that goes back to the L fitting attached to the brake booster hose. Install back Desa. 20

The other side of the 6mm hose that comes from the snail pipe goes to the L fitting that branches off from the brake booster line. On this same L fitting the overflow line from the fuel regulator is attached. Remove overflow line (hard plastic) from the L fitting and plug nipple on the L fitting with the vacuum plug provided. Attach the vacuum line that was previously installed at the back of the manifold to the blowoff valve, T the line from the fuel regulator (overflow line) into the blowoff valve vacuum line. Chrome pipe is then attached to the snail pipe followed by the HFM and then the air filter. The head light module has to be relocated on some models. 21

Pull the under panel clips. Pull the side panel screws. Slide off bumper; disconnect any wires to the horns. Adjust the air filter and HFM. Replace bumper. Mount oil reservoir bracket on the passenger side firewall. 23

Mount oil cooler in front of A/C condenser behind plastic cowling. Cowling does not need to be removed. Note the position of the bracket uprights. The bracket will look as if it is back ways. Install reservoir with lines. Inlet line goes on the bottom of the reservoir. This line has the magnetic filter in it. The arrow must face towards the SC. 24

Relocate head light module using the bracket provided. Drill a 1/8 inch hole in the frame rail and attach the bracket with light module. Extend the HFM wire (original wire will not reach HFM behind headlight) with wires provided. Match the 3 wires color for color. Attach the HFM connector to the HFM before installing below the head light. Slide the air filter, HFM and chrome pipe down behind the head light and attach to the snail pipe. In some cases you may have to remove the front bumper to better adjust the air filter. Pull the two torx bolts under the bumper. 22

Run the line against the firewall behind the engine. Make sure not to kink the line. The inlet oil line goes on the driver s side of the SC with the other end to the BOTTOM of the reservoir. The outlet side goes on the passenger side of the SC with the other end to the oil cooler. Outlet line runs from passenger side of SC OUTLET to the top of oil cooler. 25

From the outlet side of the SC run the line through the side of the head light to the oil cooler. Make sure to screw on fitting by hand first. These fittings have been pretested at AA prior to shipping. Tighten to 22 ft lbs. Cut a small hole through the plastic, beside the passenger head light so that the oil line can reach the right side of the oil cooler. Feed the return line of the oil cooler from the top of the reservoir, down behind the passenger head light, then through the cut hole. Loop the line around as shown in the picture so that the line does not kink. Make sure the inlet and outlet lines are hooked up properly. 26

OIL LINE DIAGRAM. Arrow on filter points towards SC 27

FUEL INJECTORS - SOFTWARE Remove injector connector rail by prying up with a screw driver. Remove injector rail with injectors. Remove the stock injectors and replace with the new ones supplied. Remove the factory fuel injectors. -Lubricate the fuel injector seals going into the rail and the manifold. -Use a small amount of engine oil as a lubricant. 28

Reinstall fuel injector rail with new injectors using spacers and bolts provided (injectors are longer). Install back fuel injector connector rail. SOFTWARE Remove the Insulated cover by the Passenger Firewall. -This insulates heat from the engine DME. Make sure ignition remains off. DME has black connectors. Disconnect the connectors from the DME. Then slide out DME by pulling up while pushing back on the plastic clips that hold the side of the DME. Do not crank car without the DME. This can put EWS out of alignment. -Have the DME shipped to AA for software uploading to match the SC install. Ship To: Active Autowerke 9940 SW 168 Terrace Miami, Florida 33157 USA 305-233-9300 Call a Sales representative before shipping the DME. 29

FINAL CHECK Add fluid to reservoir till it is full, start the car and watch for the level to go down. Add fluid as it goes down. System usually takes about 7/8 of the bottle. With the car idling, screw in the cap then remove and check level it should be at MIN mark. If fluid is higher than this you could have foaming out of the cap at high RPM. If fluid does not go down Turn off car and recheck lines. Inlet line should gravity feed. -Check belt tension and pulleys, proper routing of all pipes and hose to prevent possible chafing. -Check all vacuum hose connections. Put back engine covers. -Road test. Install AA SC plaque on core support. Use Silicone glue for adhesion or drill and rivet. Picture used for illustrative purposes only. 30

AA Tuning Supercharger Maintenance Items OIL SERVICE OIL FILTER Replace engine oil & filter at least every 3,000 miles with good quality synthetic oil DIFFERENTIAL Replace oil with Redline 85W140 GL5 gear lube every 7500-10,000 miles SPARK PLUG Replace with factory spark plugs every 10,000-15,000 miles Mobil 5w30, 10w30 Castrol 5w30, 10w30 BMW Synthetic 5w30 Motul 5w40 11-42-1-730-389 Oil Filter 1993 BMW 325i 1995 BMW M3 1996-1999 BMW M3 11-42-1-427-908 Oil Filter 1996-1998 BMW 328i Redline 85w140 GL5 12-12-9-063-428 F7LDCR 1993-1995 BMW 325i AIR FILTER AA SC USES K&N air filters 12-12-9-069-877 FGR8KQC 1996-1998 BMW 328i, M3 RU3190 1993-1995 BMW 325i 1996-1998 BMW 328i 1995-1999 BMW M3 RU3130 2001 BMW 330i SC BELT Check every 5,000 miles 060895 6PKx2289 with 100mm Pulley 1995 BMW M3 C38 1996-1999 M3 C38 2001-2005 330i SC OIL BRAKE FLUID COOLANT Check oil level every 5,000 miles. Replace with Rotrex friction oil every 40,000 to 50,000 miles or every 2 years if driven less than 5,000 miles per year 6539002 SC traction oil SX100 BMW Specified 2 Year Interval BMW Specified 2 Year 31

PRINT OUT THIS FORM SEND BACK WITH ECU Customer s Name: Shipping Address: Phone Number: E-Mail: Invoice # Model: Year: Trans: V.I.N. Engine type: Please ship your DME to: Active Autowerke 9940 S.W. 168 Terrace Miami, FL 33157 USA 305-233-9300 It is advisable to insure this package with your carrier of choice for a value of approximately $1,000.00 USD. International Customers are responsible to pay for all customs and duty charges. Instructions on the air bill should indicate this. If not, Active Autowerke has the right to either refuse the package or assess an estimation of the charges and will not release the reprogrammed DME until payment has been received. 32

AA Tuning Supercharger Maintenance Items OIL SERVICE OIL FILTER DIFFERENTIAL SPARK PLUG Replace engine oil & filter at least every 3,000 miles with good quality synthetic oil Replace oil with Redline 85W140 GL5 gear lube every 7500-10,000 miles Replace with factory spark plugs every 10,000-15,000 miles Mobil 5w30, 10w30 Castrol 5w30, 10w30 BMW Synthetic 5w30 Motul 5w40 11-42-1-730-389 Oil Filter 1993 BMW 325i 1995 BMW M3 1996-1999 BMW M3 11-42-1-427-908 Oil Filter 1996-1998 BMW 328i Redline 85w140 GL5 12-12-9-063-428 F7LDCR 1993-1995 BMW 325i 12-12-9-069-877 FGR8KQC 1996-1998 BMW 328i, M3 AIR FILTER AA SC USES K&N air filters RU3190 1993-1995 BMW 325i 1996-1998 BMW 328i 1995-1999 BMW M3 RU3130 2001 BMW 330i SC BELT Check every 5,000 miles 5060880 6PKx2236 with 85mm Pulley 1993-1995 BMW 325i 1996-1998 BMW 328i 1995 BMW M3 1996-1999 BMW M3 SC OIL Check oil level every 5,000 miles. Replace with Rotrex friction oil every 40,000 to 50,000 miles or every 2 years if driven less 679-2240 6PKx2240 with 90mm Pulley 1993-1995 BMW 325i 1996-1998 BMW 328i 1995 BMW M3 1996-1999 BMW M3 6539002 SC traction oil SX100

BRAKE FLUID COOLANT every 2 years if driven less than 5,000 miles per year BMW Specified 2 Year Interval BMW Specified 2 Year Interval