RDL O SPLIT CASE I05KSB002 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontally or vertically installed, single-stage, axially split volute casing pump with double-entry radial impeller, mating flanges to DIN, ISO, BS or ANSI standards. Applications: water, irrigation and drainage pumping stations, power stations, industrial water supply systems, shipbuilding and general applications in the petrochemical industry; pumping clean, raw and service water, seawater. Materials to DIN or ASTM standards. Main applications Installation position Industry and process engineering; Water; Energy; Mining / Dredges Horizontal or vertical Stationary Shaft seal type Gland packing; Mechanical seal Maximum drive rating 3.300 kw Maximum speed of rotation 1.800 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate 1.200 m³/h
RDL O SPLIT CASE Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage 10.000 m³/h 15,00 m 240,00 m 25 bar Cast iron; Cast duplex steel; Nodular cast iron; Ni-Resist Long-coupled Dry installed Direct; Gear Rolling element and plain bearings grease-/oil- and product lubrication Electric motor 50 Hz /60 Hz Low voltage, high voltage Max. permissible fluid temperature 105 C Suitable for drinking water Guaranteed to be silicon-free Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position Casing partition No. of impeller entries Type of casing Type of impeller PN 10; PN 16; PN 25 Flange Non-priming In-line Axially split Double entry Volute casing Closed; Radial
RDL P SPLIT CASE I05KSB003 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontally or vertically installed, single- or two-stage, axially split volute casing pump with double-entry radial impeller, mating flanges to DIN, ISO or ANSI standards. Applications: pumping clean, raw and service water, seawater, hydrocarbons and crude oil. Materials to DIN or ASTM standards in all material combinations required. Installation position Horizontal or vertical Stationary Shaft seal type Gland packing; Mechanical seal Maximum drive rating 15.000 kw Maximum speed of rotation 3.600 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate 700 m³/h Maximum flow rate 18.000 m³/h Minimum head 150,00 m Maximum head 600,00 m Maximum discharge-side pressure 70 bar Casing material Cast steel; Cast stainless steel; Cast duplex steel; Nodular cast iron
RDL P SPLIT CASE Casing material (EN standard) 1.4408; 1.4517; GP240GH+QT; JS 1030 Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Long-coupled Dry installed Direct; Gear Rolling element and plain bearings Grease / Product lubrication Electric motor 50 Hz /60 Hz Low voltage, high voltage Max. permissible fluid temperature 105 C Suitable for drinking water Guaranteed to be silicon-free Maximum rated pressure (discharge) Type of connection PN 64; PN 100 Flange Suction characteristics Non-priming Nozzle position In-line Impeller material (EN standard) 1.4313; 1.4404; 1.4517; CC480K-GS; JS 1030 Diffuser material (EN standard) 1.4404; 1.4517; CC480K-GS; JS 1030 Shaft material (EN standard) Casing partition Type of casing Type of impeller Type of first impeller Other impeller types 1.4021; 1.4429; 1.4462; C45+QT Axially split Volute casing Closed; Radial Double entry Closed / Radial
RDL SPLIT CASE I05KSB004 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontally or vertically installed, single- or two-stage, axially split volute casing pump with double-entry radial impeller, mating flanges to DIN, ISO, BS or ANSI standards. Applications: water, irrigation, and drainage pumping stations, power stations, docks, fire fighting systems, refineries, pipelines and tank farms; pumping clean, raw and service water, seawater, crude oil and refinery intermediate products. Materials to DIN or ASTM standards, available in various material combinations. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Water; Energy; Mining / Dredges; Oil / Gas; Shipping / Shipbuilding Horizontal or vertical Stationary Gland packing; Mechanical seal 3.500 kw 1.200 1/min eclass assignment 36410000; 36410100; 36410103 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 1.800 m³/h 12.000 m³/h 15,00 m 150,00 m 25 bar
RDL SPLIT CASE Casing material Cast iron; Stainless steel; Nodular cast iron; Carbon steel Casing material (EN standard) A48 CLASS 30 (JL 1030); A48 CLASS 35 (JL 1040); A536 CLASS 604018 (JS 1030) Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Long-coupled Dry installed Direct; Gear Rolling element and plain bearings grease-/oil- and product lubrication Electric motor Drive frequency 50 Hz /60 Hz Drive voltage Low voltage, high voltage Max. permissible fluid temperature 160 C Suitable for drinking water Guaranteed to be silicon-free Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position Impeller material (EN standard) Diffuser material (EN standard) Shaft material (EN standard) Casing partition No. of impeller entries Type of casing Type of impeller PN 10; PN 16; PN 25 Flange Non-priming In-line A743CA6NM (1.4313.95); A743CF8M (1.4408); B 584-90500 (CC480K-GS) AISI 420 (1.4021); SAE 1045 (C45E+N) AISI 420 (1.4021); SAE 1045 (C45E+N) Axially split Double entry Volute casing ; Closed; Radial
AHO Horizontal, Single- or Multistage, Self-Priming Side Channel Pump I05KSB005 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, single- or multistage, self-priming side channel pump, suitable for pumping gas-containing fluids, with mechanical seal. Applications: pumping clean fluids without abrasive and solid substances. Main applications Installation position Shaft seal type Maximum drive rating Industry and process engineering Horizontal Stationary Gland packing; Mechanical seal 7 kw Maximum speed of rotation 1.750 1/min eclass assignment 36410000; 36410100; 36410104 Minimum flow rate 0,30 m³/h Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material 9 m³/h 10,00 m 180,00 m 16 bar Cast iron; Cast stainless steel Casing material (EN standard) 1.4581; JL 1040 Maximum suction pressure Pump set location Type of coupling 16 bar Long-coupled Dry installed Direct
AHO Horizontal, Single- or Multistage, Self-Priming Side Channel Pump Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Max. permissible fluid temperature Suitable for drinking water Guaranteed to be silicon-free Rolling element and plain bearings Grease / Oil lubrication Electric motor 50 Hz /60 Hz Low voltage 120 C No No UNSPSC classification 4015150300 Standard EN 734 Maximum rated pressure (discharge) Type of connection PN 16 Flange Suction characteristics Nozzle position Impeller material (EN standard) Barrel casing Self-priming Top-top 1.4059; 1.4581; CW718R No Shaft material (EN standard) 1.4021+QT700; 1.4571 Pull-out design Casing partition Heatable No. of impeller entries Type of discharge casing Suction casing material (EN standard) Type of first impeller Other impeller types Stage casing material (EN standard) Discharge casing material (EN standard) No Radially split No Single entry Annular casing 1.4581; JL 1040 Star impeller Star impeller 1.4462; JL 1040 1.4581; JL 1040
AHO Horizontal, Single- or Multistage, Self-Priming Side Channel Pump
AHR Horizontal, Single- or Multistage, Self-Priming Side Channel Pump I05KSB006 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, single- or multistage, self-priming side channel pump, suitable for pumping gas-containing fluids, with mechanical seal, with suction and discharge nozzle pointing radially to the top (AHR) or with axial suction nozzle and special suction impeller to improve self-priming ability (AHRS). Applications: pumping clean fluids without abrasive and solid substances. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering Horizontal Stationary Mechanical seal 55 kw 1.750 1/min eclass assignment 36410000; 36410100; 36410104 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 0,30 m³/h 24,20 m³/h 10,00 m 361,00 m 40 bar
AHR Horizontal, Single- or Multistage, Self-Priming Side Channel Pump Casing material Cast iron; Cast stainless steel; Nodular cast iron Casing material (EN standard) 1.4408; JL 1040; JS 1025 Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Long-coupled Dry installed Direct Rolling element bearings Pressurized oil lubrication Electric motor 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 200 C Standard EN 734 Maximum rated pressure (discharge) Type of connection Suction characteristics PN 40 Flange Self-priming Nozzle position Impeller material (EN standard) Variable 1.4059; 1.4581; CW718R Shaft material (EN standard) 1.4021+QT700; 1.4571 Casing partition No. of impeller entries Type of stage casing Type of discharge casing Type of suction casing Suction casing material (EN standard) Type of first impeller Other impeller types Stage casing material (EN standard) Discharge casing material (EN standard) Radially split Single entry Stage casing without diffuser Annular casing Annular casing 1.4408; JL 1040; JS 1025 Star impeller Star impeller 1.4470; JL 1040; JS 1030 1.4408; JL 1040; JS 1025
AHR Horizontal, Single- or Multistage, Self-Priming Side Channel Pump
CPK S / E / C END SUCTION CENTRIFGAL PUMPS I05KSB007 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, radially split, single-stage volute casing pump in back pull-out design, with single-entry radial impeller, to EN 22 858 / ISO 2858 / ISO 5199. Applications: handling aggressive, organic and inorganic fluids in chemical and petrochemical processes, in refinery off-sites, in the paper and cellulose industries, food and luxury food industries, sugar industry, in seawater desalination plants, absorption equipment in environmental engineering systems, power stations etc. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Energy; Mining / Dredges Horizontal Stationary Gland packing; Mechanical seal 3.200 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 1 m³/h 4.800 m³/h 2,00 m 275,00 m 25 bar
CPK S / E / C END SUCTION CENTRIFGAL PUMPS Casing material Special KSB material; Cast steel; Cast stainless steel; Cast duplex steel Casing material (EN standard) 1.4408; GP240GH+N; JS 1025; NORIDUR 1.4593 Long-coupled Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Dry installed Direct Rolling element bearings Grease / Product lubrication Electric motor 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 400 C Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position PN 25 Flange Non-priming End suction Impeller material (EN standard) 1.4408; GP240GH+N; JL 1040; NORIDUR 1.4593 Shaft material (EN standard) 1.5680; 1.7709VS; C 45+N Pull-out design Casing partition No. of impeller entries Type of casing Type of impeller Radially split Single entry Volute casing Closed; Multi-vane impeller; Radial
CPK N END SUCTION I05KSB008 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, radially split, single-stage volute casing pump in back pull-out design to EN 22 858 / ISO 2858 / ISO 5199, with single-entry radial impeller. CPK variant with shaft reinforced in the shaft seal area, reinforced bearings, also available with "wet" shaft and/or conical seal chamber. Applications: pumping aggressive fluids in the chemical and petrochemical industry. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Energy Horizontal Stationary Mechanical seal 285 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 1 m³/h 1.250 m³/h 2,00 m 220,00 m 25 bar
CPK N END SUCTION Casing material Cast steel; Cast stainless steel; Cast duplex steel; Nodular cast iron; Ni Casing material (EN standard) 1.4408; GP240GH+N; JS 1025; NORIDUR 1.4593 Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Long-coupled Dry installed Direct Rolling element bearings Grease / Product lubrication Electric motor 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 400 C Suitable for drinking water Guaranteed to be silicon-free No No Standard EN 22858; ISO 2858; ISO 5199 Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position PN 25 Flange Non-priming End suction Impeller material (EN standard) 1.4408; JL 1040; NORIDUR 1.4593 Barrel casing No Shaft material (EN standard) 1.4462; 1.5680; 1.7709; C 45+N Pull-out design Casing partition Heatable No. of impeller entries Type of casing Type of impeller Radially split No Single entry Volute casing Closed; Radial
CPK O END SUCTION I05KSB009 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, radially split, single-stage volute casing pump in back pull-out design to EN 22 858 / ISO 2858 and ISO 5199, with open single-entry impeller, tried and tested CPK modular design system. Applications: pumping fluids liable to polymerize or clot and gas-containing fluids in the chemical and petrochemical industry. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Energy Horizontal Stationary Gland packing; Mechanical seal 85 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101
CPK O END SUCTION Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material 1 m³/h 310 m³/h 2,00 m 155,00 m 16 bar Cast stainless steel Casing material (EN standard) 1.4408 Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Long-coupled Dry installed Direct Rolling element bearings Grease / Product lubrication Electric motor Drive frequency Drive voltage 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 300 C Maximum rated pressure (discharge) Type of connection PN 16 Flange Suction characteristics Non-priming Nozzle position End suction Impeller material (EN standard) 1.4408 Shaft material (EN standard) 1.4462; 1.7709.05S; C45+N Pull-out design Casing partition No. of impeller entries Type of casing Type of impeller Radially split Single entry Volute casing Open; Radial; Multi-vane impeller
Etabloc GN / BN / CN / SN / MN / G END SUCTION I05KSB010 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Close-coupled, single-stage volute casing pump with ratings to EN 733. Replaceable shaft protecting sleeves and impeller wear rings. Applications: water supply, irrigation and spray irrigation, drainage, heating and air-conditioning systems, pumping drinking water, service water, hot water, cooling water, swimming pool water, seawater, fire fighting water, condensate, oil, brine, cleansing agents, brackish water, etc. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Water; Energy; Building services Horizontal or vertical Stationary Mechanical seal 45 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101
Etabloc GN / BN / CN / SN / MN / G END SUCTION Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material 1 m³/h 670 m³/h 2,00 m 95,00 m 16 bar Cast iron; Cast stainless steel; Nodular cast iron; Bronze Casing material (EN standard) 1.4408; CC480K-GS; GJS-400-18-LT; JL 1040; JS 1025 Pump set location Type of coupling Type of drive Close-coupled Dry installed Direct Electric motor Drive frequency 50 Hz /60 Hz Drive voltage Low voltage Max. permissible fluid temperature 140 C Suitable for drinking water Guaranteed to be silicon-free Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position PN 16 Flange Non-priming End suction Impeller material (EN standard) 1.4408; CC480K-GS; JL 1040 Shaft material (EN standard) 1.4571; C45N Pull-out design Casing partition No. of impeller entries Type of casing Type of impeller Radially split Single entry Volute casing Closed; Radial; Multi-vane impeller; Closed / Radial
Etabloc-SY END SUCTION I05KSB011 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Fan-cooled, single stage volute casing pump, close-coupled to standardized motor. Applications: heat transfer systems (DIN 4754) or hot water circulations systems. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Energy; Building services Horizontal Stationary Mechanical seal 22 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 2 m³/h 315 m³/h 3,00 m 70,00 m 16 bar
Etabloc-SY END SUCTION Casing material Nodular cast iron Casing material (EN standard) JS 1025 Close-coupled Pump set location Dry installed Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Direct Plain bearings Oil / Product lubrication Electric motor 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 350 C UNSPSC classification 4015150300 Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position PN 16 Flange Non-priming End suction Impeller material (EN standard) JL 1040 Shaft material (EN standard) 1.4021.05 Pull-out design Casing partition No. of impeller entries Type of casing Type of impeller Product configurable Radially split Single entry Volute casing Closed; Radial; Multi-vane impeller; Closed / Radial configurable
Etachrom B & BC END SUCTION I05KSB012 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, close-coupled, single-stage annular casing pump, ratings and main dimensions to EN 733. Replaceable casing wear rings. Applications: water supply, irrigation and spray irrigation, drainage, heating, air-conditioning and fire fighting systems, pumping drinking water, service water, hot water, cooling water, swimming pool water, fire fighting water, condensate, oil and cleansing agents. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Water; Energy; Building services Horizontal Stationary Mechanical seal 45 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 2 m³/h 250 m³/h 2,00 m 108,00 m 12 bar
Etachrom B & BC END SUCTION Casing material Chrome nickel molybdenum steel Casing material (EN standard) 1.4571 Pump set location Type of coupling Type of drive Close-coupled Dry installed Direct Electric motor Drive frequency 50 Hz /60 Hz Drive voltage Low voltage Max. permissible fluid temperature 110 C Suitable for drinking water Guaranteed to be silicon-free Standard Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position DIN PN 12 Flange Non-priming End suction Impeller material (EN standard) 1.4571 Barrel casing No Shaft material (EN standard) 1.4571 Pull-out design Casing partition Heatable No. of impeller entries Type of casing Type of impeller Drive Integrated control system Radially split No Single entry Annular casing Closed; Radial; Multi-vane impeller; Closed / Radial IEC standardized motor No Connection to power supply 220/400/690 V, 3~
Etachrom N & NC END SUCTION I05KSB013 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, long-coupled, single-stage annular casing pump in back pull-out design made of deep-drawn chrome nickel molybdenum steel, ratings and main dimensions to EN 733. Replaceable casing wear rings. Applications: water supply, irrigation and spray irrigation, drainage, heating, air-conditioning and fire fighting systems, pumping drinking water, service water, hot water, cooling water, swimming pool water, fire fighting water, condensate, oil and cleansing agents. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Water; Energy; Building services Horizontal Stationary Mechanical seal 45 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 2 m³/h 260 m³/h 2,00 m 106,00 m 12 bar
Etachrom N & NC END SUCTION Casing material Chrome nickel molybdenum steel Casing material (EN standard) 1.4571 Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Long-coupled Dry installed Direct Ball bearings Pressurized oil lubrication Electric motor 50 Hz /60 Hz Low voltage Explosion protection IP 55 Max. permissible fluid temperature 110 C Suitable for drinking water Guaranteed to be silicon-free Standard Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position DIN / ANSI PN 12 Flange Non-priming End suction Impeller material (EN standard) 1.4571 Barrel casing No Shaft material (EN standard) 1.4571 Pull-out design Casing partition Heatable No. of impeller entries Type of casing Type of impeller Radially split No Single entry Annular casing Closed; Radial; Multi-vane impeller; Closed / Radial
ETALINE SY IN-LINE I05KSB014 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Close-coupled, single-stage, in-line volute casing pump with standardized motor. The pump shaft is rigidly connected to the motor shaft. Applications: heat transfer systems (DIN 4754) or hot water re-circulation systems. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Building services Horizontal Stationary Mechanical seal 22 kw 2.900 1/min eclass assignment 36410101
ETALINE SY IN-LINE Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material Casing material (EN standard) Pump set location Type of coupling Type of bearing Type of lubrication Type of drive 2 m³/h 315 m³/h 3,00 m 70,00 m 16 bar Nodular cast iron JS1025 In-line Dry installed Direct Plain bearings Oil / Product lubrication Electric motor Drive frequency 50 Hz /60 Hz Drive voltage Low voltage Max. permissible fluid temperature 350 C UNSPSC classification 4015150300 Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position Impeller material (EN standard) PN 16 Flange Non-priming In-line JL1040 Shaft material (EN standard) 1.4021.05 Type of casing Type of impeller Drive Volute casing Closed / Radial IEC standardized motor
Non-Clog End Suction Centrifugal Pumps I05KSB016A Industrial / Commercial / Food Processing / Beverage / Chemical / Laboratory / Pharmaceutical / Water Treatment / Automotive / Municipal The problems in waste water engineering are many. In response to the multitude of economical and ecological challenges, technological applications must be equally as diverse. We offer a solution tailored to each individual case. Our Non-Clog End Suction Centrifugal Pumps serves as a good example. With it s innovative design and hydraulic concept, marks the beginning of a new generation of dry-installed waste water pumps, thus setting a new standard. The concept: The service-friendly dry-well installation bears some clear advantages, such as high operational reliability, easy monitoring and clean maintenance. All commercial motors can be applied. The modular system: Four types of impellers, a selection of various materials, and the option of either horizontal or vertical installation will cover any application you might require. Hydraulic system, material, bearing carrier, and drive unit can therefore be tailored to suit your particular application and installation requirements. This optimized combination stands for operational reliability. Standard components reduce the number of spare parts to a minimum. For additional information please refer to your PFE CD Catalogue. Pump sizes: 50 to 500 Max. capacity: 1400 l/s Max. discharge head: 90m Max. discharge pressure:10 bar Max. temperature: +60 Deg C
Non-Clog End Suction Centrifugal Pumps High Operational Reliability Double-acting mechanical seals in tandem arrangement with oil reservoir ensure leak proof seal. Cost Reduction Standard components ensure interchangeability within the entire series of submersible pumps, thus optimizing spare parts management. Flexible Hydraulic Design Impeller and casing design optimized for pumping waste water. Low Maintenance Grease-packed rolling element bearings sealed for life
Multitec A / B / C / D MULTI-STAGE I05KSB017 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, long- or close-coupled, multistage centrifugal pump in ring-section design, with axial or radial suction nozzle, cast radial impellers. Applications: general and municipal water and drinking water supply, industry, pressure boosting, irrigation; power stations; heating, filter, fire fighting, reverse osmosis and washing plants, snow guns, pumping boiler feed water, warm water, hot water, condensate, distillate, solvents, lubricants, fuels, etc. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Water; Building services Horizontal Stationary Gland packing; Mechanical seal 315 kw 4.000 1/min eclass assignment 36410000; 36410100; 36410101
Multitec A / B / C / D MULTI-STAGE Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material Casing material (EN standard) Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage 4 m³/h 850 m³/h 20,00 m 630,00 m 63 bar Cast iron; Cast steel; Cast stainless steel 1.4408; GP240GH+N; JL1040 Long-coupled Dry installed Direct Rolling element and plain bearings grease-/oil- and product lubrication Electric motor, turbine, I.C. engine 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 200 C Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position Impeller material (EN standard) Diffuser material (EN standard) Shaft material (EN standard) Casing partition No. of impeller entries Type of stage casing Type of discharge casing Type of suction casing Suction casing material (EN standard) Type of first impeller Other impeller types Stage casing material (EN standard) Discharge casing material (EN standard) PN 16, PN 25, PN 40, PN 63 Flange Non-priming Variable 1.4408; CC480K-GS; JL1040 1.4408; CC480K-GS; JL1040 1.4021+QT; 1.4462; C45+N Radially split Single entry Stage casing with diffuser Annular casing Annular casing 1.4408; GP240GH+N; JL 1040 Closed / Radial Closed / Radial 1.4404; 1.4408; GP240GH+N; JL 1040; S355J2G3 1.4408; GP240GH+N; JL 1040
HGM HORIZONTAL, RADIALLY SPLIT, MULTISTAGE RING-SECTION PUMP I05KSB021 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, radially split, multistage ring-section pump with single- or double-entry radial impellers. Applications: feedwater transport in utility power stations. Main applications Installation position Shaft seal type Industry and process engineering; Energy Horizontal Stationary Mechanical seal Maximum drive rating 1.200 kw Maximum speed of rotation 3.600 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 8 m³/h 274 m³/h 200,00 m 1.400,00 m 140 bar
HGM HORIZONTAL, RADIALLY SPLIT, MULTISTAGE RING-SECTION PUMP Casing material Maximum suction pressure Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Cast steel; Chrome steel 7 bar Long-coupled Dry installed Direct Plain bearings Oil / Product lubrication Electric motor, turbine 50 Hz /60 Hz Low voltage, high voltage Max. permissible fluid temperature 160 C UNSPSC classification 4015150300 Maximum rated pressure (discharge) Type of connection PN 64, PN 100, PN 160 Flange Suction characteristics Nozzle position Casing partition No. of impeller entries Type of stage casing Type of discharge casing Type of suction casing Type of first impeller Other impeller types Non-priming Variable Radially split Single entry Stage casing with diffuser Annular casing Annular casing Closed / Radial Closed / Radial
ETANORM R END SUCTION I05KSB025 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, long-coupled, single-stage volute casing pump (pump size 125-500/2 with two stages) in back pull-out design. Replaceable shaft sleeves / shaft protecting sleeves and casing wear rings. Applications: irrigation and spray irrigation, drainage, district heating systems, water supply, fire fighting, heating and airconditioning systems, pumping condensate, hot water, cooling water, fire fighting water, oil, swimming pool water, brine, drinking water, brackish water, service water, etc. Main applications Installation position Shaft seal type Maximum speed of rotation Industry and process engineering; Water; Waste water / sewage; Energy; Building Horizontal Stationary Gland packing; Mechanical seal 1.750 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material 50 m³/h 2.280 m³/h 2,50 m 90,00 m 16 bar Cast iron; Nodular cast iron
ETANORM R END SUCTION Casing material (EN standard) JL 1040; JS 1025 Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Long-coupled Dry installed Direct Ball bearings Grease / Oil lubrication Electric motor, turbine 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 140 C Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position PN 16 Flange Non-priming End suction Impeller material (EN standard) 1.4408; G-CUSN10; GJL-250; JL 1040 Shaft material (EN standard) Pull-out design Casing partition No. of impeller entries Type of casing Type of impeller 1.4057; C45 Radially split Single entry Volute casing Closed; Radial; Multi-vane impeller; Closed / Radial
KWP GN / GC / GH / C2 / H END SUCTION I05KSB028 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, radially split, single-stage volute casing pump in back pull-out design, single entry, available with various impeller types: non-clogging impeller, open multi-vane impeller and free flow impeller. Applications: pre-treated sewage, waste water, all types of slurries without stringy substances and pulps up to 5 % bone dry. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Energy Horizontal Stationary Gland packing; Mechanical seal 1.500 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101; 36410103 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 4 m³/h 7.900 m³/h 1,00 m 140,00 m 10 bar
KWP GN / GC / GH / C2 / H END SUCTION Free passage Casing material Casing material (EN standard) Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage 200 mm Cast iron; Duplex steel; Special cast material JL1040; NORIDUR 1.4593; NORIHARD Long-coupled Dry installed Direct; Gear; Jack shaft / Belt drive Rolling element bearings Grease / Product lubrication Electric motor 50 Hz /60 Hz Low voltage, high voltage Max. permissible fluid temperature 280 C Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position Impeller material (EN standard) Shaft material (EN standard) Pull-out design Casing partition No. of impeller entries Type of casing Type of impeller PN10 Flange Non-priming End suction ERN; NORIDUR 1.4593; NORIHARD C45+N Radially split Single entry Volute casing Open; Closed; Multi-vane impeller; Free flow impeller; Radial
Tyamagno-BLOC MAGNET DRIVE LINED I05KSB029 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, radially split, single-stage centrifugal pump in close-coupled design to EN 22 858 / ISO 2858 / ISO 5199, with single-entry radial impeller. Seal-less mag-drive pump. Replaceable plastic casing liner as an alternative to high-grade metal alloys. Applications: pumping highly aggressive, corrosive and harmful fluids in the chemical, petrochemical, process and general industries. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering Horizontal Stationary Magnetic drive 22 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 0,20 m³/h 94 m³/h 2,00 m 78,00 m 16 bar
Tyamagno-BLOC MAGNET DRIVE LINED Casing material Casing material (EN standard) Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Plastics; Nodular cast iron JS 1025 / PFA, PE-UHMW Close-coupled Dry installed Direct Plain bearings Oil / Product lubrication Electric motor 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 150 C Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position Impeller material (EN standard) Shaft material (EN standard) Pull-out design Casing partition No. of impeller entries Type of casing Type of impeller PN 16 Flange, loose flange Non-priming End suction PE-UHMW; PFA 1.4057 / PFA Radially split Single entry Annular casing Closed; Radial; Multi-vane impeller; Closed / Radial
Tyachem LINED I05KSB031 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, radially split, single-stage centrifugal pump in back pull-out design to EN 22 858 / ISO 2858 / ISO 5199, with single-entry radial impeller. Replaceable plastic casing liner as an alternative to high-grade metal alloys. Applications: pumping highly aggressive, corrosive and abrasive fluids in the chemical, process and general industries. Shaft seal: mechanical seal. Main applications Installation position Industry and process engineering; Energy; Oil / Gas Horizontal Stationary Shaft seal type Mechanical seal Maximum speed of rotation 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material 0,50 m³/h 375 m³/h 2,00 m 95,00 m 16 bar Plastics; Nodular cast iron
Tyachem LINED Casing material (EN standard) Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage JS 1025 / PFA; PE-UHMW; PVDF Long-coupled Dry installed Direct Rolling element bearings Grease / Product lubrication Electric motor 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 150 C Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position Impeller material (EN standard) Shaft material (EN standard) Pull-out design Casing partition No. of impeller entries Type of casing Type of impeller PN 16 Flange Non-priming End suction PE-UHMW; PFA; PVDF 1.4057+QT800 Radially split Single entry Annular casing Closed / Radial
Magnochem MAGNETIC DRIVE I05KSB033 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, radially split, single-stage volute casing pump in back pull-out design to EN 22 858 / ISO 2858 / ISO 5199, with single-entry radial impeller. Seal-less mag-drive pump. Applications: pumping aggressive, toxic, explosive, valuable, inflammable, mal-odours or hazardous fluids in chemical, petrochemical and general industrial processes. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Energy Horizontal Stationary Magnetic drive 160 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 1 m³/h 1.400 m³/h 3,50 m 225,00 m 25 bar
Magnochem MAGNETIC DRIVE Casing material Cast iron; Special KSB material; Cast steel; Cast stainless steel; Nodula Casing material (EN standard) 1.4408; GP240GH+N; JS 1025; NORIDUR 1.4593 Pump set location Type of coupling Type of bearing Type of lubrication Long-coupled Dry installed Direct Ball and plain bearings Oil / Product lubrication Type of drive Electric motor Drive frequency 50 Hz /60 Hz Drive voltage Low voltage Max. permissible fluid temperature 300 C Suitable for drinking water Guaranteed to be silicon-free Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position No No PN 25 Flange Non-priming End suction Impeller material (EN standard) 1.4408; JL 1040; JS 1025; NORIDUR 1.4593 Barrel casing Shaft material (EN standard) Pull-out design Casing partition Heatable No. of impeller entries Type of casing Type of impeller No 1.4462; C45+N Radially split Single entry Volute casing Closed; Radial; Multi-vane impeller; Closed / Radial
ETAPRIME L SELF PRIMING I05KSB038 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, long-coupled, self-priming single-stage volute casing pumps with open multi-vane impeller, in back pull-out design. Applications: pumping clean, contaminated or aggressive fluids without abrasive or solid substances. Main applications Installation position Shaft seal type Industry and process engineering; Water; Waste water / sewage; Building service Horizontal Stationary Mechanical seal Maximum drive rating 37 kw Maximum speed of rotation 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 4 m³/h 170 m³/h 5,00 m 104,00 m 10 bar
ETAPRIME L SELF PRIMING Free passage Casing material 10 mm Cast iron; Cast stainless steel Casing material (EN standard) 1.4408; JL 1040 Pump set location Type of coupling Type of bearing Long-coupled Dry installed Direct Rolling element bearings Type of lubrication Pressurized oil lubrication Type of drive Electric motor Drive frequency 50 Hz /60 Hz Drive voltage Low voltage Max. permissible fluid temperature 90 C Suitable for drinking water Guaranteed to be silicon-free Maximum rated pressure (discharge) Type of connection Suction characteristics Nozzle position PN 16; PN 40 Screw-ended, flange Self-priming End suction Impeller material (EN standard) 1.4408; CC483K-GS; JL 1040 Barrel casing Diffuser material (EN standard) Shaft material (EN standard) Pull-out design Casing partition Heatable No. of impeller entries Type of casing Type of impeller Drive No 1.4462; 1.4571; C45+N 1.4462; 1.4571; C45+N Radially split No Single entry Volute casing Open; Multi-vane impeller IEC standardized motor, electric motor
EXACHEM CANNED I05KSB039 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, seal-less, single-stage volute casing pump in back pull-out design, with single-entry radial impeller, fully enclosed canned motor; low noise emission. Casing connection dimensions to EN 22 858 / ISO 2585. Applications: pumping aggressive, toxic, volatile or valuable fluids in the chemical and petrochemical industries, as well as in environmental engineering and industrial processes. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering Horizontal Stationary Canned motor pump 55 kw 3.500 1/min eclass assignment 36410000; 36410100; 36410101 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 1 m³/h 300 m³/h 3,50 m 153,00 m 25 bar
EXACHEM CANNED Casing material Cast iron; Cast steel; Cast stainless steel Casing material (EN standard) 1.0619+QT; 1.4408; NORIDUR 1.4593 Long-coupled Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Explosion protection Dry installed Direct; None Plain bearings Oil / Product lubrication Electric motor 50 Hz /60 Hz Low voltage E EX DE II B T4, T3 Max. permissible fluid temperature 130 C Suitable for drinking water Guaranteed to be silicon-free Maximum rated pressure (discharge) Type of connection Suction characteristics No No PN 25 Flange Non-priming Nozzle position End suction Impeller material (EN standard) 1.4408; NORIDUR 1.4593 Barrel casing No Shaft material (EN standard) 1.4462 Pull-out design Casing partition Heatable No. of impeller entries Type of casing Type of impeller Radially split Single entry Volute casing Closed; Radial; Multi-vane impeller; Closed / Radial
KRT SUBMERSIBLE PUMPS I05KSB042A Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Vertical, single-stage, close-coupled submersible motor pump with various impeller types, for wet-well installation, stationary or transportable design. Applications: pumping all kinds of waste water in waste water management and industrial plants, in particular untreated sewage with long-fibre and solid substances, airand gas-containing fluids, as well as raw, activated and digested sludge. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Water; Waste water / sewage; Energy; Building services; Mining / Dredges Vertical Transportable; Stationary Mechanical seal 700 kw 3.500 1/min eclass assignment 36410101; 36410103 Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure 0,60 m³/h 10.000 m³/h 1,00 m 100,00 m 10 bar
KRT SUBMERSIBLE PUMPS Free passage Casing material 240 mm Cast iron Casing material (EN standard) JL 1040 Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage Explosion protection Close-coupled Wet well None Rolling element bearings Grease / Product lubrication Electric motor 50 Hz /60 Hz Low voltage CSA; EEX D IIB T3; EEX D IIB T4; FM Max. permissible fluid temperature 60 C Maximum rated pressure (discharge) Type of connection Cutter Suction characteristics PN 16 Flange Non-priming Nozzle position End suction Impeller material (EN standard) 1.4517; JL 1040; JN 3029 Shaft material (EN standard) 1.4021; C45+N Casing partition Type of casing Type of impeller Radially split Volute casing Open; Closed; Multi-vane impeller; Free flow impeller; Radial; Single-va impeller; Diagonal
KRT SUBMERSIBLE PUMPS
KRT SUBMERSIBLE PUMPS
SEZ VERTICAL SINGLE / MULTI-STAGE I05KSB047 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Vertical, single- or two-stage tubular casing pump with open mixed flow impeller. Pump intake with inlet nozzle or suction elbow on option, pull-out design available, discharge nozzle arranged above- or under floor, flanges to DIN or ANSI standards available. Applications: pumping raw, clean, service and cooling water in industrial circuits, water supply systems, power stations and seawater desalination plants. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Industry and process engineering; Water; Energy Vertical Stationary Gland packing; Mechanical seal 5.000 kw 990 1/min eclass assignment 36410000; 36410100; 36410106
SEZ VERTICAL SINGLE / MULTI-STAGE Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage 5.000 m³/h 65.000 m³/h 7,00 m 33,00 m 9 bar Chrome nickel steel; Duplex steel; Carbon steel Long-coupled Dry installed; Wet well Direct; Gear Rolling element and plain bearings Oil / Pressurized oil lubrication Electric motor 50 Hz /60 Hz Low voltage, high voltage Max. permissible fluid temperature 40 C Maximum rated pressure (discharge) Type of connection Suction characteristics Casing partition No. of impeller entries Type of casing Type of impeller PN 6; PN 9 Flange Non-priming Radially split Single entry Tubular casing Open; Mixed flow impeller
Movitec LHS IN-LINE MULTISTAGE I05KSB055 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Multi-stage, vertical (horizontal installation on request) high-pressure centrifugal pumps, with suction and discharge nozzles of identical nominal diameters arranged opposite to each other (in-line design). Movitec VE are employed for general water supply, sprinkling, irrigation and pressure boosting duties, for warm water and cooling water re-circulation. They are installed in domestic water supply systems; washing plants, water treatment and fire-fighting systems. Movitec V(S) and LHS are employed for general water supply, sprinkling, irrigation and pressure boosting duties, for warm water, hot water and cooling water recirculation, and condensate transport. They are installed in boiler feed circuits, domestic water supply systems, washing plants, water treatment and filter systems. They are used for degreaser baths/alkaline cleaning baths, alkalines and oils/emulsions, as well. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material Industry and process engineering; Water; Building services Vertical Stationary Mechanical seal 11 kw 2.900 1/min 1 m³/h 8,60 m³/h 1,00 m 401,00 m 40 bar Chrome nickel molybdenum steel
Movitec LHS IN-LINE MULTISTAGE Casing material (EN standard) 1.4408 Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage In-line Dry installed Direct Plain bearings Oil / Product lubrication Electric motor 50 Hz /60 Hz Low voltage Max. permissible fluid temperature 120 C Suitable for drinking water Guaranteed to be silicon-free Maximum rated pressure (discharge) Type of connection Nozzle position No 40 BAR Flange In-line Impeller material (EN standard) 1.4404 Barrel casing Shaft material (EN standard) 1.4401 Pull-out design Casing partition Heatable No. of impeller entries Type of stage casing Type of discharge casing Type of suction casing Suction casing material (EN standard) Type of first impeller Stage casing material (EN standard) Discharge casing material (EN standard) No Radially split No Single entry Stage casing without diffuser Stage casing without diffuser Stage casing without diffuser 1.4408 Axial 1.4404 1.4408
BSX, BRY, BRZS, BRE, BSF VERTICAL MULTI-STAGE PUMPS I05KSB060 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Single- or multistage centrifugal pumps in ring-section design, single entry; for vertical and depending on the number of stages angled and horizontal installation; mixed flow hydraulic systems available with reduced impeller diameters; driven by submersible motors. Applications: pumping clean or slightly contaminated water in general water supply, irrigation and spray irrigation systems, lowering and maintaining ground water levels, pressure boosting, emergency water supply, as well as mines and fountains etc. Suction casing fitted between pump and motor, equipped with strainer to protect the pump from coarse particles in the fluid. Permissible sand content in the fluid: 50 g/m³. Pumps with non-return valve or connection branch on option. Installation position Shaft seal type Horizontal or vertical Stationary Shaft seal ring; Mechanical seal Maximum drive rating 1.000 kw Maximum speed of rotation 1.750 1/min eclass assignment 36410000; 36410100; 36410106 Minimum flow rate 200 m³/h
BSX, BRY, BRZS, BRE, BSF VERTICAL MULTI-STAGE PUMPS Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Casing material Casing material (EN standard) Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage 2.600 m³/h 8,00 m 230,00 m 35 bar Cast iron; Stainless steel; Bronze 1.4408; 1.4593; CC480K; JL1030 Wet well Direct Plain bearings Oil / Product lubrication Electric motor 50 Hz /60 Hz Low voltage, high voltage Max. permissible fluid temperature 50 C Suitable for drinking water Guaranteed to be silicon-free Maximum rated pressure (discharge) Type of connection Suction characteristics Impeller material (EN standard) Barrel casing No PN 40 Flange Non-priming 1.4408; 1.4593; CC480K No Diffuser material (EN standard) CC480K; JL 1030 Shaft material (EN standard) 1.4021; 1.4462 Pull-out design Casing partition Heatable No. of impeller entries Type of stage casing Type of suction casing Suction casing material (EN standard) Type of first impeller Other impeller types Stage casing material (EN standard) No Radially split No Single entry Stage casing with diffuser Annular casing CC480K; JL1030 Mixed flow Mixed flow CC480K; JL1030
AMEREX KRT B SUBMERSIBLE PUMPS I05KSB062 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Vertical, single-stage, close-coupled submersible motor pump with various impeller types, for dry installation, floodable. Applications: pumping all kinds of waste water in waste water management and industrial plants, in particular untreated sewage with long-fibre and solid substances, air- and gas-containing fluids, as well as raw, activated and digested sludge. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Water; Waste water / sewage Vertical Stationary Mechanical seal 300 kw 1.750 1/min eclass assignment 36410101
AMEREX KRT B SUBMERSIBLE PUMPS Minimum flow rate Maximum flow rate Minimum head Maximum head Maximum discharge-side pressure Free passage Casing material 1 m³/h 4.000 m³/h 1,50 m 100,00 m 10 bar 143 mm Cast iron Casing material (EN standard) JL 1040 Pump set location Type of coupling Type of bearing Close-coupled Dry installed, floodable None Rolling element bearings Type of lubrication Type of drive Drive frequency Grease / Product lubrication Electric motor 50 Hz /60 Hz Drive voltage Low voltage Max. permissible fluid temperature 40 C Maximum rated pressure (discharge) Type of connection PN 16 Flange Suction characteristics Nozzle position Non-priming End suction Impeller material (EN standard) JL 1040 Shaft material (EN standard) Casing partition No. of impeller entries Type of casing Type of impeller Drive 1.4021; C45+N Radially split Single entry Volute casing Open; Closed; Multi-vane impeller; Free flow impeller; Radial; Single-va Electric motor
AMALINE MIXERS I05KSB065 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Wet-well, horizontal submersible motor propeller pump, driven by spur gear or direct drive; ECB propeller with 3 fixed, fibre-repellent blades. Bolt-less connection to discharge pipe. Applications: recirculation of activated sludge in sewage treatment systems. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Waste water / sewage Horizontal Stationary Mechanical seal 16 kw 960 1/min eclass assignment 36410000; 36410106
AMALINE MIXERS Minimum propeller diameter Pump set location Type of coupling Type of bearing Type of lubrication Type of drive Drive frequency Drive voltage 800 mm Wet well Direct; Gear Rolling element bearings Pressurized oil lubrication Electric motor 50 Hz /60 Hz Low voltage Explosion protection Max. permissible fluid temperature Drive EEX D IIB T3; EEX D IIB T4 40 C Electric motor Connection to power supply 400 V, 3~ Self-cleaning Unit PC
AMAMIX SUBMERSIBLE MIXERS I05KSB066 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, close-coupled submersible mixer with self-cleaning ECB propeller, driven by coaxial spur gear. Applications: mixing, homogenizing and thickening municipal or industrial sewage and sludge. Main applications Installation position Shaft seal type Maximum drive rating Waste water / sewage Horizontal Transportable; Stationary Mechanical seal 16 kw Maximum speed of rotation 460 1/min eclass assignment 36410000; 36410106 Minimum propeller diameter 800 mm Pump set location Wet well Type of coupling Type of bearing Type of lubrication Gear Rolling element bearings Pressurized oil lubrication
AMAMIX SUBMERSIBLE MIXERS Type of drive Drive frequency Drive voltage Explosion protection Electric motor 50 Hz /60 Hz Low voltage EEX D IIB T3; EEX D IIB T4 Max. permissible fluid temperature 40 C Drive Self-cleaning Electric motor
AMAPROP SUBMERSIBLE MIXERS I05KSB067 Industrial / Commercial / Food Processing / Beverage / Chemical / Pharmaceutical / Water Treatment / Automotive / Oil & Gas Horizontal, close-coupled submersible mixer with self-cleaning ECB propeller, driven by coaxial spur gear. Applications: re-circulation, suspension and dispersion of municipal or industrial sewage and sludge. Main applications Installation position Shaft seal type Maximum drive rating Maximum speed of rotation Waste water / sewage Horizontal Stationary Mechanical seal 6,50 kw 120 1/min eclass assignment 36410000; 36410106 Minimum propeller diameter Pump set location Type of coupling Type of bearing Type of lubrication 2.500 mm Wet well Gear Rolling element bearings Pressurized oil lubrication
AMAPROP SUBMERSIBLE MIXERS Type of drive Drive frequency Drive voltage Explosion protection Electric motor 50 Hz /60 Hz Low voltage EEX D IIB T3; EEX D IIB T4 Max. permissible fluid temperature 40 C Drive Electric motor Connection to power supply 230V; 400V; 500V; 690 V; 3~ Self-cleaning