BULLETIN 34B FLOWS TO 275 GPM Sethco Seal-less, End Suction Magnetic Drive Centrifugal Pumps For Corrosive Liquid and Chemical Transfer
SETHCO END SUCTION CORROSION RESISTANT MAGNETIC DRIVE, SEAL-LESS CHEMICAL PUMPS Sethco magnetic drive, seal-less pumps are precision designed to meet the demands of a wide range of OEM, chemical and industrial applications. These pumps can be used for highly corrosive or mild chemicals, acids or solvents at flows to 275 GPM at temperatures to 21 F. Leakproof, Seal-less Construction No shaft seal is used or required on these magnetically driven pumps. Power is transmitted by a magnetic field traveling from a magnet attached to the motor, through the solid body of the pump, to a magnet attached to the impeller. No shaft seal ensures that leakage and troublesome seal replacement are completely eliminated. The superior seal-less, magnetic drive design provides a reliable, smooth running, vibration-free pump that delivers high flow and pressure. PVDF Model KM-55 Excellent Chemical Resistance The wetted components of these rugged seal-less pumps are available in your choice of Polypropylene or all PVDF. Polypropylene is glass reinforced and PVDF is carbon reinforced for added strength and reliability. These materials offer broad corrosion resistance to acids, alkalies, caustics, bleaches, sea water, solvents and many harsh environments. All pumps include a 99.5% Alumina ceramic shaft and thrust washers. High purity carbon bearings are standard with Ryton or silicone carbide available where required. Viton o-rings are standard on all pumps, while teflon and EPDM are available. There is no metal contact with the liquid being pumped. Polypropylene Model PM-255 Run Dry Capability Once a Sethco end suction pump has been primed with solution, it is possible for it to run dry without damage if flow to the pump is interrupted for any reason. Run dry times may vary depending on model, bearing type and piping configuration. Designed for Reliability Among its many features is its unique impeller/driven magnet design. The two are separate distinct pieces so that one can be replaced without having to purchase the other. This feature also reduces the load on the front bearing and trust washer. Easy to Maintain In the event a pump should ever need service, the limited number of parts allows for easy disassembly, inspection and maintenance without any special tools or talent. The motor can be separated from the pump housing without difficulty. Magnetic coupling design acts as a clutch to eliminate motor burnout and overloading under adverse conditions. Magnet housing acts as an insulator to prevent motor heat from being transferred to the fluid being pumped Polypropylene Model PM-14W
5 series for flows to 4 GPM (15 LPM) PERFORMANCE CURVE DIMENSIONS Motor HP Volts/Phase A M P 1/4 115-28/23, 1 ph 16-3/16" (411mm) 7-5/8" (194mm) 2-1/8" (54mm) 1/3 115-28/23, 1 ph 16-3/16" (411mm) 7-5/8" (194mm) 2-1/8" (54mm) 1/3 115-28/23, 1 ph 16-13/16" (427mm) 8-1/4" (29mm) 2-1/8" (54mm) 1/2 115-28/23, 1 ph 17-5/16" (44mm) 8-3/4" (194mm) 2-1/8" (54mm) 1/2 28-23/46, 3 ph 16-13/16" (427mm) 8-1/4" (29mm) 2-1/8" (54mm 3/4 115-28/23, 1 ph 18-5/16" (465mm) 9-3/4" (247mm) 2-1/8" (54mm) 3/4 28-23/46, 3 ph 18-5/16" (465mm) 9-3/4" (247mm 2-1/8" (54mm PUMP SPECIFICATIONS: FLOW CAPACITIES TO 4 GPM, PRESSURE TO 38 FT. 6 MODELS TO CHOOSE FROM Model Number Flow Maximum Maximum Head Operating Motor Characteristics* Weight Polypropylene PVDF GPM LPM Ft. M. Temp. (F / C) HP* Volts Hz. Phase Type Lbs. Kg. PM-51 KM-51 2 75 28 8.5 Polypropylene 1/4 3 13.6 PM-525 KM-525 32 12 33 1 18 F / 82 C 1/3 115/23 6 1 ph TEFC 31 14 PVDF PM-55 KM-55 4 15 38 11.5 21 F / 99 C 1/2 34 15.5 * Customer supplied external overload protection is required on 3 phase motors. Consult factory for 5 Hz. motor. Explosion proof motors are available Add approximately 3 pounds for PVDF. Add approximately 2% extra for shipping weight.
1 series for flows to 96 GPM (22 m 3 /hr) PERFORMANCE CURVE (35 RPM) (29 RPM) DIMENSIONS Motor HP Volts/Phase A M P 1/2 115-28/23, 1 ph 18-3/8" (466mm) 8-3/4" (222mm) 2-1/8" (54mm) 1/2 28-23/46, 3 ph 17-7/8" (454mm) 8-1/4" (21mm) 2-1/8" (54mm) 3/4 115-28/23, 1 ph 19-3/8" (492mm) 9-3/4" (248mm) 2-1/8" (54mm) 3/4 28-23/46, 3 ph 19-3/8" (492mm) 9-3/4" (248mm) 2-1/8" (54mm) 1 115-28/23, 1 ph 19-3/8" (492mm) 9-3/4" (248mm) 2-1/8" (54mm) 1 28-23/46, 3 ph 19-3/8" (492mm) 9-3/4" (248mm) 2-1/8" (54mm 2 115-28/23, 1 ph 2-7/8" (53mm) 11-1/4" (285mm) 1-1/2" (38mm) 2 28-23/46, 3 ph 19-7/8" (54mm) 1-1/4" (26mm) 1-1/2" (38mm) 3 28-23/46, 3 ph 21-3/8" (543mm) 11-3/4" (298mm) 1-1/2" (38mm) 4 28-23/46, 3 ph 21-3/8" (543mm) 11-3/4" (298mm) 1-1/2" (38mm) PUMP SPECIFICATIONS: FLOW CAPACITIES TO 96 GPM, PRESSURE TO 8 FT. 8 MODELS TO CHOOSE FROM Model Number Flow Maximum Maximum Head Operating Motor Characteristics* Weight Polypropylene PVDF GPM m 3 /hr Ft. M. Temp. (F / C) HP* Volts Hz. Phase Type Lbs. Kg. PM-135 KM-135 54 12 36 11 Polypropylene 1/2 34 15.4 PM-14N KM-14N 62 14 53 16 18 F / 82 C 3/4 115/23 6 1 ph TEFC 35 15.8 PM-14W KM-14W 76 17 6 18 PVDF 1 37 16.8 PM-15 KM-15 96 22 8 24 21 F / 99 C 2 *Customer supplied external overload protection is required on 3 phase motors. Consult factory for 5 Hz. motor. Explosion proof motors are available Add approximately 3 pounds for PVDF. Add approximately 2% extra for shipping weight. 3 ph (23/46V) 43 19.5
25 series for flows to 275 GPM (62 m 3 /hr) PERFORMANCE CURVE DIMENSIONS M Motor Motor HP Volts/Phase A Varies By P Frame Motor Selected Standard 3 5 7.5 1 28-23/46 27" 14-1/4" 2-3/4" 3 Phase (686 mm) (362 mm) (7 mm) 28-23/46 29" 16-1/4" 2-3/4" 3 Phase (737 mm) (413 mm) (7 mm) 28-23/46 28-3/4" 16" 3-1/2" 3 Phase (73 mm) (46 mm) (89 mm) 28-23/46 3" 17-1/4" 3-1/2" 3 Phase (762 mm) (438 mm) (89 mm) 182TC 184TC 213TC 215TC PUMP SPECIFICATIONS: FLOW CAPACITIES TO 275 GPM, PRESSURE TO 15 FT. 8 MODELS TO CHOOSE FROM Model Number Flow Maximum Maximum Head Operating Motor Characteristics* Weight Polypropylene PVDF GPM m 3 /hr Ft. M. Temp. (F / C) HP* Volts Hz. Phase Type Lbs. Kg. PM-255 KM-255 17 38.5 6 18 Polypropylene 3 84 38 PM-251 KM-251 195 44 76 23 18 F / 82 C 5 28-23/ PM-2525 KM-2525 22 5 85 26 PVDF 5 46 6 3 ph TEFC 15 48 15 48 PM-255 KM-255 275 56.5 15 32 21 F / 99 C 7-1/2 191 86 *Customer supplied external overload protection is required on 3 phase motors. Consult factory for 5 Hz. motor. Explosion proof motors are available. Model with 1 HP motor is available. Add approximately 3 pounds for PVDF. Add approximately 2% extra for shipping weight.
SETHCO SEAL-LESS, END SUCTION, MAGNETIC DRIVE, CENTRIFUGAL PUMPS GALLONS PER MINUTE 35 RPM QUICK SELECTION GUIDE FOR MODELS PM & KM PUMPS Add PM before model number for Polypropylene construction and KM before model number for PVDF construction. HEAD (Feet) 35 RPM 1 2 3 4 5 6 7 8 9 1 1 51 525 55 14NT 14NT 15 15 2525 255 255 2 525 55 135NT 14NT 14WT 15 15 2525 255 255 3 55 135NT 14NT 14WT 14WT 15 15 2525 255 255 4 135NT 14NT 14NT 14WT 15 15 2525 2525 255 255 5 135NT 14NT 14WT 14WT 15 15 2525 255 255 255 6 14WT 14WT 14WT 15 15 251 2525 255 255 7 14WT 15 15 15 251 251 2525 255 255 8 15 15 15 255 251 2525 2525 255 255 9 15 15 255 255 251 2525 255 255 255 1 255 255 255 251 251 2525 255 255 255 11 255 255 255 251 2525 2525 255 255 12 255 255 251 251 2525 2525 255 255 13 255 255 251 2525 2525 255 255 255 14 255 251 251 2525 2525 255 255 255 15 255 251 251 2525 255 255 255 16 251 251 2525 2525 255 255 255 17 251 2525 2525 255 255 255 255 18 251 2525 2525 255 255 255 19 2525 2525 255 255 255 255 2 2525 255 255 255 255 21 2525 255 255 255 255 22 255 255 255 255 23 255 255 255 255 24 255 255 255 25 255 255 26 255 255 27 255 Note: Not all selections will work for every application due to different specific gravity of liquids. Please consult a Sethco Application Engineer before purchasing a pump. COPYRIGHT 23 MET-PRO CORPORATION, SETHCO DIVISION Sethco Division IS A REGISTERED TRADEMARK OF MET-PRO CORPORATION 8-4-5M Sethco Division Mailing Address: P.O. Box 12128, Hauppauge, New York 11788-843 Shipping Address: 7 Arkay Drive, Hauppauge, New York 11788-3773 Tel: 8-645-5 631-435-53 Fax: 631-435-654 Website: www.sethco.com e-mail: sethcosales@met-pro.com West Coast Office: 23 N. Crescent Way, Unit I, Anaheim, CA 9281 Tel: 714-991-27 Fax: 714-991-817
SETHCO SEALLESS, SELF-PRIMING, MAGNETIC DRIVE CENTRIFUGAL PUMPS For Corrosive Liquids and Chemical Transfer PVDF Version Polypropylene Version
SETHCO SEALLESS, SELF-PRIMING MAGNETIC DRIVE CENTRIFUGAL PUMPS FOR CORROSIVE LIQUIDS AND CHEMICAL TRANSFER Polypropylene Model 14 PMSP DESIGN FEATURES APPLICATIONS TYPICAL PMSP SERIES ASSEMBLY DRAWING
5 SERIES FOR FLOWS TO 27 GPM (12 LPM), HEADS TO 36 FT. (11 M) Composite Curves M 12.1 FT (6 hz) 4 36 9.7 32 HEAD 7.3 28 24 2 51 525 55 FOR MODELS 4.8 16 12 2.4 8 4 3 6 9 12 15 18 21 24 27 3 19 38 57 76 95 114 FLOW GPM (6 hz) LPM Dimensions A 1'' MNPT DISCHARGE 12 3/8'' 12 3/16'' 1 7/8'' B 4'' M 1'' MNPT INLET 6 1/2'' 5/16'' 4 7/8'' 1 1/2'' 3 3/4'' 2 9/16'' 1 1/4'' 2 7/16'' 1 1/2'' DETAIL OF MOTOR FOOT Ø 1/4'' MOTOR/PUMP DETAILS MOTOR HP VOLTS/PHASE A B M 1/4 115V, 1 PH 2 [58] 7 5/8 [194] 8 5/8 [219] 1/3 115V, 1 PH 2 [58] 7 5/8 [194] 8 5/8 [219] 1/2 3/4 5 5/8'' 115V, 1 PH 28-23/46 3PH 115V, 1 PH 28-23/46 3PH 3 1/4'' NOTES: Motor dimensions may vary by manufacturer. 3 1/4'' 21 1/8 [537] 2 5/8 [524] 22 1/8 [562] 22 1/8 [562] 2 1/16'' 3 1/2'' 9 1/4'' 11 7/8'' 8 3/8 [213] 7 5/8 [194] 9 1/8 [232] 8 3/8 [213] 8 7/8 [225] 8 7/8 [225] All dimensions in inches. Dimensions in [ ] are millimeters. Pump Specifications: 6 Models Available Model Number Polypropylene PVDF Max Flow Max Head Max Operating Temperature Motor Characteristics* Weight (Lbs./Kg.) GPM LPM Ft. M HP* Volts Hz Phase Type Lbs. Kg. PMSP-51 KMSP-51 18 68 28 8.5 Polypropylene: 18 F / 82 C 1/4 1 PH 32 14.5 PMSP-525 KMSP-525 21 79 3 9 1/3 23/46 6 1 PH TEFC 33 15 PMSP-55 KMSP-55 27 12 36 11 PVDF: 21 F / 99 C 1/2 1 & 3 PH 36 16.3 * Customer supplied overload protection is required on 3 phase motors. Consult Factory for the following options: 5 Hz. motors, explosion proof motors, and alternate motor HPs. Add approximately 3 lbs./1.4 kg. for PVDF. Add approximately 2% extra for shipping weight.
1 SERIES FOR FLOWS TO 76 GPM (288 LPM), HEADS TO 66 FT. (2 M) Composite Curves M FT (6 hz) 24.3 8 72 19.5 14.6 64 56 48 14W/14HG 15 FOR MODELS HEAD 4 9.7 32 14N 24 135 4.8 16 8 9 18 27 36 45 54 63 72 81 9 GPM (6 hz) 57 113 17 FLOW 227 283 34 LPM Dimensions A 14'' 2 1/4'' 5'' M 1 1/4'' 2''* 5/16'' *Use only on 2 HP and up. 3'' 3 3/4'' 6 1/2'' 2 9/16'' 4 7/8'' 6 1/2'' 13 3/4'' MOTOR/PUMP DETAILS MOTOR HP VOLTS/PHASE A B M 1/2 3/4 1 3 1/2'' B 13 5/8'' 1 1/2'' 115V, 1 PH 22 3/8 [568] 8 3/8 [213] 28-23/46V, 3 PH 21 5/8 [549] 7 5/8 [194] 115V, 1 PH 23 1/8 [587] 9 1/8 [232] 28-23/46V, 3 PH 22 3/8 [568] 4 7/8 [124] 8 3/8 [213] 115V, 1 PH 23 5/8 [6] 9 5/8 [244] 28-23/46V, 3 PH 23 3/8 [594] 9 3/8 [238] 2 28-23/46V, 3 PH 24 1/4 [616] 1 1/4 [26] 3 28-23/46V, 3 PH 25 3/4 [654] 5 1/4 [133] 11 3/4 [298] NOTES: Motor dimensions may vary by manufacturer. INLET/DISCHARGE DIAMETER INLET DISCHARGE MODEL DIA. DIA. 135 1 1/4'' FNPT 1 1/4'' FNPT 14 15 1 1/2'' FNPT 1 1/2'' FNPT All dimensions in inches. Dimensions in [ ] are millimeters. Pump Specifications: 1 Models Available Model Number Polypropylene PVDF Max Max Flow Max Head Motor Characteristics* Weight (Lbs./Kg.) Operating GPM LPM Ft. M Temperature HP* Volts Hz Phase Type Lbs. Kg. PMSP-135 KMSP-135 59 151 31 9.4 1/2 38 17 PMSP-14N KMSP-14N 49 185 46 14 Polypropylene: 18 F / 82 C 1 4 18 PMSP-14W KMSP-14W 59 223 53 16 1 115/23 6 1 & 3 PH TEFC 41 18.6 PVDF: PMSP-14HG KMSP-14HG 6 227 53 16 2 47 21.3 21 F / 99 C PMSP-15 KMSP-15 76 288 66 2 2 3 PH(23/46V) 47 21.3 * Customer supplied overload protection is required on 3 phase motors. Consult Factory for the following options: 5 Hz. motors, explosion proof motors, and alternate motor HPs. Add approximately 3 lbs./1.4 kg. for PVDF. Add approximately 2% extra for shipping weight.
25 SERIES FOR FLOWS TO 23 GPM (87 LPM), HEADS TO 93 FT. (28 M) Composite Curves M FT (6 hz) 33.5 11 99 26.8 88 HEAD 2.1 77 66 55 251 2525 255 FOR MODELS 13.4 44 33 255 6.7 22 11 24 48 72 96 12 144 168 192 216 24 GPM (6 hz) 151 32 454 65 757 98 LPM FLOW Dimensions 2'' MNPT DISCHARGE A 2 3/8'' 6 1/16'' 2 3/4'' D M 2 1/2'' MNPT INLET C B G H F P Ø 7/16'' 6 HOLES 18 5/8'' E DETAIL OF MOTOR FOOT MOTOR/PUMP DETAILS MOTOR HP VOLTS/PHASE A B C D E F G H M P 3 28-23/46V, 3 PH 32 1/2 [826] 14 3/8 [365] 17 3/8 [441] 7 13/16 [198] 4 1/2 [114] 1 [25] 7 1/2 [191] 13 7/8 [353] 4 1/2 [114] 5 28-23/46V, 3 PH 32 1/2 [826] 14 3/8 [365] 17 3/8 [441] 7 13/16 [198] 4 1/2 [114] 1 [25] 7 1/2 [191] 13 7/8 [353] 7.5 28-23/46V, 3 PH 34 1/4 [87] 15 1/8 [384] 18 1/8 [46] 8 11/16 [221] 5 1/2 [14] 1 1/2 [38] 8 1/2 [216] 15 5/8 [397] 5 1/4 [133] 1 28-23/46V, 3 PH 35 5/8 [95] 15 1/8 [384] 18 1/8 [46] 8 11/16 [221] 5 1/2 [14] 1 1/2 [38] 8 1/2 [216] 17 [432] NOTES: Motor dimensions may vary by manufacturer. All dimensions in inches. Dimensions in [ ] are millimeters. 3 3/8 [86] 4 1/4 [18] Pump Specifications: 8 Models Available Model Number Polypropylene PVDF Max Flow Max Head Max Motor Characteristics* Weight (Lbs./Kg.) Operating GPM LPM Ft. M Temperature HP* Volts Hz Phase Type Lbs. Kg. PMSP-255 KMSP-255 13 49 55 17 Polypropylene: 3 91 41.3 PMSP-251 KMSP-251 165 625 72 22 18 F / 82 C 5 133 6.3 28-23/46 6 3 PH TEFC PMSP-2525 KMSP-2525 19 719 8 24 PVDF: 5 133 6.3 PMSP-255 KMSP-255 23 87 93 28 21 F / 99 C 7 1/2 199 9.3 * Customer supplied overload protection is required on 3 phase motors. Consult Factory for the following options: 5 Hz. motors, explosion proof motors, and alternate motor HPs. Add approximately 3 lbs./1.4 kg. for PVDF. Add approximately 2% extra for shipping weight.
PRIMING TIME 5 SERIES SELF-PRIMING MAGNETIC DRIVE PUMPS 4.6 15 55 3.8 3. 12.5 1 525 51 FOR MODELS METERS 2.3 FEET 7.5 1.5 5.8 2.5.5 1 1.5 2 2.5 3 MINUTES NOTE: The above priming times are based on water (SG = 1.) using a 1'' inlet hose connected to the pump suction. Consult Factory for priming times with other fluids or different suction tubing. PRIMING TIME 1 SERIES SELF-PRIMING MAGNETIC DRIVE PUMPS 6.1 2 15 FOR MODELS METERS 4.6 3. FEET 15 1 14W/14HG 14N 135N 1.5 5.5 1 1.5 MINUTES 2 2.5 3 3.5 NOTE: The above priming times are based on water (SG = 1.) using a 1-1/4'' inlet hose connected to the pump suction for all pumps except the PMSP-15. The PMSP-15 has a 1-1/2'' inlet hose. Consult Factory for priming times with other fluids or different suction tubing.
PRIMING TIME 25 SERIES SELF-PRIMING MAGNETIC DRIVE PUMPS 6.1 4.6 2 15 255 2525 251 FOR MODELS METERS 3. FEET 1 255 1.5 5.5 1 1.5 2 2.5 3 3.5 MINUTES NOTE: The above priming times are based on water (SG = 1.) using a 2'' inlet hose connected to the pump suction. Consult Factory for priming times with other fluids or different suction tubing. METHOD OF PRIMING Priming the pump is easy. Simply fill the priming chamber with liquid through the wide opening at the top. Secure the cover and turn on the pump. When the pump is started, the impeller discharges a mixture of liquid and air into the discharge chamber. The air is separated and vented through the discharge while the liquid is returned to the impeller. This priming liquid continues to draw in more air from the suction line. The cycle continues until all air is evacuated from the suction line and replaced by the liquid to be pumped, at which time the pump is "primed".
Bulletin 35A ABOUT MET-PRO GLOBAL PUMP SOLUTIONS Met-Pro Global Pump Solutions, which combines the resources of the Company s internationally recognized Dean, Fybroc and Sethco brands, is a leading niche-oriented global provider of solutions and products for the pumping of corrosive, abrasive and high temperature liquids. Its broad range of high quality centrifugal pumps provide excellent performance for tough applications including pumping of acids, brines, caustics, bleaches, seawater, high temperature liquids and a wide variety of waste liquids for a broad range of applications including the chemical, petrochemical, metal finishing, wastewater treatment, desalination and aquarium/aquaculture markets. ABOUT MET-PRO Met-Pro Corporation is a global provider of solutions and products for product recovery, pollution control and fluid handling applications. The Company s products include filtration and purification equipment for air, water and harsh, corrosive applications; fluid handling equipment for water, corrosive, abrasive, and high temperature liquids; and proprietary water treatment chemicals. For more information, visit www.met-pro.com. 8 E m l e n W a y, Te l f o r d, PA 1 8 9 6 9 P : 8. 6 4 5. 5 F : 2 1 5. 7 9 9. 9 2 info@mp-gps.com www.mp-gps.com 211 MET-PRO CORPORATION SETHCO IS A REGISTERED TRADEMARK OF MET-PRO CORPORATION 911