Vortex In Line Flow Meter

Vortex In Line Flow Meter Principles of Operation Vortices are created when a fluid passes around a bluff body as shown below. Vortices are alternately shed on each side of the body, 0 degrees out of phase to each other, resulting in an oscillating pressure gradient. As flow increases the frequency of vortices increases in proportion to the increased flow thereby creating a linear relationship. Aalborg s unique dual signal processing technology independently measures each vortex on either side of the bluff body and filters out non-flow noise. This results in less noise and higher accuracy throughout the flow range. Dual signal processing technology independently measures each vortex providing increased accuracy and turndown. Benefits RELIABLE WIDE RANGEABILITY HIGH ACCURACY No moving parts to wear or fail. Electronics can be remote mounted up to 30.5 m (00 ft). No fluid to sensor contact. No holes to clog. High flow turndown ratio up to 0:. Dual signal processing technology improves accuracy at low flows. + 0.5% of rate. Increased noise cancellation as a result of dual signal processing technology. Functional Specifications FLUID TYPES MAXIMUM PRESSURE FLUID TEMPERATURE LOW FLOW CUT-OFF HIGH FLOW CUT-OFF Steam, Gas, Liquid. F 03 bar (50 psig) with wafer mount See table 3 for flange mount. -73 F to 232 F C std./to 36 F C opt. (-00 F to 50O F std./to F F opt). Adjustable: Set @ min. per Tables 2 to 32. Adjustable: Set @ max. per Tables 2 to 32. Vortex In line Flow meter shown with wafer mounting VOLTAGE 5/230 VAC selectable or 2 VDC. FREQUENCY 50/60 Hz. OUTPUTS Analog: -20 ma DC into ohm or less. LINEAR RANGE Reynolds number of >0,000. Figure 29 WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. BULLETIN EM20050

Vortex In Line Flow Meter Performance Specifications Physical Specifications ACCURACY + 0.5% of rate. MATERIALS OF CONSTRUCTION REPEATABILITY FLOW TURNDOWN RATIO RESPONSE TIME DAMPING VELOCITY RANGE AGENCY APPROVALS* + 0.25% of rate. See Tables 2 to 32. 0.5 sec. Adjustable: to 0 sec. Liq.:.32 or 0000µ to 30 ft/sec ñd 2 Steam & Gas: (/ñ)/3 to 250 ft/sec ñ= density (lb/ft3) d= pipe diameter (in) µ= viscosity (cp) FM and CSA Class Div 2 Groups B,C,D. *Designed to meet. Contact Aalborg for status of the agency approval. SHEDDER BAR ELECTRODES METERING TUBE FLANGES ELECTRONICS HOUSING 30 SS or 36 SS. 30 SS or 36 SS encapsulated ceramic. 30 SS or 36 SS. 30L SS or 36L SS. Epoxy coated aluminum. CONNECTIONS AND MOUNTINGS MOUNTING POSITION TYPICAL STRAIGHT PIPE REQUIREMENTS TEMPERATURE TAP (BY CUSTOMER) Vertical, horizontal, angle. Upstream: 20 x D. Downstream: 5 x D. Downstream: 3.5 x D. PRESSURE TAP (BY CUSTOMER) PROCESS CONNECTIONS ELECTRICAL CONNECT Upstream: 3.5 x D. ANSI Class 50 RF, RF, RF, RF, 500 RF, DIN, Wafer. 3/ FNPT. Electronic Specifications AMBIENT TEMPERATURE -2 F to 2 F C (-5 F to 0 F F). Vortex In line Flow Meter shown with flange mounting TRANSMITTER Microprocessor-based. DISPLAY Two lines, simultaneous rate and total, 6 alphanumeric characters each. FUNCTIONS OUTPUT SIGNAL Zero, span, hi cutoff, low cutoff, response time, sample time, engineering units, totalizer, data logger, RS-232 interface. -20mA output into Ohm or less, 5V TTL Pulse Output. Use or 20 gauge twisted pair shielded cable. ENCLOSURE PROTECTION NEMA X. BULLETIN EM20050 ENCLOSURE APPROVALS POWER SUPPLY UL, CSA, FM, Class I Groups B, C, D Class II Groups E, F, G, KEMA/CENELEC EEx d IIB 5 30 VDC or 5 / 230 VAC (optional). WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. 30

Vortex In Line Flow Meter Flow Ranges Minimum and maximum flow rates to achieve accuracy in GPM, L/min. Pipe ID based on schedule 0 steel. SIZE (INCH) TABLE 2 - WATER FLOW RATES AT 60 F F 3/" ".5" 2" 3" " 6" min max min max min max min max min max min max min max GPM 2.6 0. 3. 67.2 7.3 6.9 2. 276.0 27.2 67.6 7.3 075.3 07.2 237.2 L/MIN 9.9 52.9 2. 25.3 27.5 62. 6.0 0.9 02.9 2337.9 79. 070. 05.9 9225. Minimum and maximum flow rates to achieve accuracy lb/hr. Pipe ID based on schedule 0 steel. TABLE 29 - SATURATED STEAM FLOW RATES AT SELECTED PROCESS PRESSURES (English) Size (inch) 3/" ".5" 2" 3" " 6" Pressure (psig) min max min max min max min max min max min max min max 0 25 50 75 00 25 50 200 250 350 00 50 500 550.7.7 6.0 9.6 22.9 25.9 2. 3. 39. 3.7.2 52.5 56.6 60.7 6.7 6.5 63.6 255.2 03.9 550.0 693.9 37.0 979. 263.9 5.7 3. 22.7 20. 2702.7 2997.5 3295. 3596..5 9.5 26.5 32.6 3. 3. 7.9 56. 65.0 72. 0.2 7.3 9.2 0.0 07.5.0 272.2 2. 67.9 9. 5.2 392.2 629. 202.2 2576.0 3050.7 3529.0 00.0 95.5 95.9 5.3 59.6 35.7.0 65. 0.0 93. 05.9 7.6 39. 59.6 7.6 96. 2.3 23.3 27. 26.0 279. 66. 0.9 69.3 225. 233. 37. 00.0 560. 6323.9 79.3 663. 9.2 036.0 220.0 356.0 6.2 59.7 0.3 09.0 33.9 56. 77.2 96. 233.2 267.0 29.9 329. 35.7 37..7. 6.3. 73.5 2760. 375.3 7.7 579.5 6695.5 636. 052.9 2533. 9.0 67.0 6.5 203.2 225.2 2573.6 33.5 79.6 23.9 299.6 39.9 396.5 0. 52. 597.5 66. 737.0 02.6 66. 92.0 9.5 07. 250.7 390.2 675.9 09.3 0609.7 2797.7 9.6 932.6 23679.9 203.5 320.2 366.6 32.3 532. 5035.9 59. 232.5 32.6 2.7 52.7 609. 690.2 766.7 90.5 00.3 6.5 23.2 397.3 507.9 65.7 72.0 2.2 355.6 6792. 0752. 60.7 7.6 2220.9 2603. 336.2 226.9 2.0 567.6 676.3 795.9 7979.5 7722.2 95729.0 526.9 70.6 962.5 2. 30.6 56. 737.6 2059.0 2357. 2639.2 290.3 366.9 37.6 366.9 3.6 3. 97.7 539. 2369. 332.7 65.3 5099.0 596. 76253.5 9339. 065.0 2006. 553. 63062.9 05.6 99.5 26966.5 3 WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. BULLETIN EM20050

In Vortex Line In Flow Line Meter Flow Meter Minimum and maximum flow rates to achieve accuracy in (kg/hr) Pipe ID based on schedule 0 steel. TABLE 30 - SATURATED STEAM FLOW RATES AT SELECTED PROCESS PRESSURES (Metric) Size (mm) 20 25 0 50 0 00 50 Pressure (bara) min max min max min max min max min max min max min max 2 6 0 22 26 2 30 32 3 36 3 0 2.5 3.9 5.9 7.7 0.6 3. 5.5 7.6 9.7 20.7 2.6 22.6 23.5 2.5 25. 26.3 5.3 6.7 66.2 23.5 395.3 55. 696.2 7.3 999. 075.9 52.9 230.2 307.9 36. 6. 53.9. 7.7.9 5.3 2.2 26.3 30.9 35.2 39.3.3 3.3 5.2 7..9 50. 52.6 7.5 2.5 273.0 00.0 69.5 96.7 3. 392.0 6.9 767.6 9.0 202.0 2.7 2277. 206. 2536.5 0.2 5.7 2.2 3.2 3.2 53.5 62.9 7.7 0... 92.0 95. 99.6 03.3 07.0.6 353.2 676.6 99.3 609.6 2222.3 23.7 39.7 069.0 30.6 693.7 500.5 5325.0 563.3 5963.7 626.0 7.0 26.2 0. 52. 7.9 9.2 0.9 9.6 33.5 0.2 6. 53.3 59.7 66.0 72.2 7. 307.7 5.6 27.6 652.2 262.6 3703.9 72.5 579.5 67.6 7.9 722.9 37.5 7.9 905.5 9939.5 076.7 3. 5.7 90.5 6.7 6.3 200.0 235.2 26. 299.3 3. 329.2 33.7 35.0 372.2 36. 399.9 69.9 39. 252.2 370.3 60.7 30. 0592. 29. 5205.0 6369. 7539. 75.9 99.5 20. 2225. 2390.0 66.3 02.2 57.6 203.3 20.9 3.3 09.6 66.9 52.2 57.5 573.3 59.7 623.6 6.3 672.6 696.6 20.7 229. 03.6 652. 076.3 6.5 50. 2253.5 263.9 252.0 30550.5 32599.0 365.9 3673.0 36.3 09.5 50.2 23.5 357. 60.6 636.3 79.0 92.0 057. 0.9 20. 29.9 356.3 2.9 6.6 523.7 57. 2722.5 5207.9 9976.5 67.3 2373.0 32769. 799.3 506. 59999.3 659.0 6922.2 7353.0 759.7 32.0 793.3 9269.7 Minimum and maximum flow rates to achieve accuracy in CFPM (.7 psia 60 F F) CFM at actual process temperature = min. or max values below *520 / ( Actual Temp.(0F) + 60) Pipe ID based on schedule 0 steel. Flow Temp. 60 F F. TABLE 3 - AIR FLOW RATES AT SELECTED PROCESS PRESSURES (English) BULLETIN EM20050 Size (inch) 3/" ".5" 2" 3" " 6" Density (lb/ft3) 0.076 0.03 0.2 0.0 0.232 0.2 0.336 0.3 0.0 0.93 0.55 0.596 0.69 0.700 0.752 0.0 0.56.6.636 Pressure (psig) 0 5 0 20 30 0 50 60 70 0 90 00 0 20 30 0 50 200 min max min max min max min max min max min max min max 2.2 2.7 3. 3.9.7 5.3 6.0 6.6 7. 7.7.2.7 9.2 9.7 0.2 0.7. 3.3 7. 5.0 60.3 75.6 06.2 36. 67. 9. 22.7 259.3 29.9 320.5 35. 3.7 2.3 3.0 73.6 50.2 657.2 963. 3.7.5 5.2 6.6 7..9 9.9 0.9.9 2. 3.7.6 5. 6.2 7.0 7..5 22. 2.5 7.9 00.3 25. 76.7 227.6 27.5 329. 30. 3.3 2.2 533. 5.0 635.0 65.9 736. 77.7 3.6 093.2 602. 9..0 2. 6. 9. 2. 2. 26. 29.2 3. 33.6 35.7 37.7 39..7 3.6 5.5 5.2 70.0 3. 26.3 30. 33. 55. 63. 0. 933. 05. 3. 30. 33. 55. 63. 0. 933. 205. 263. 3933. 5.2.5 2.5 26.9 3.9 36.5 0..9. 52.6 56.2 59. 63.2 66.5 69. 73.0 76. 90. 7. 307.5 2. 56.7 725.9 935..2 353. 562.6 77. 9.0 290.2 2399.3 260.5 27.7 3026.9 3236. 35.3 9.2 653.0 3.0.3. 60.3 7..7 9.3 00.5 09.3 7.7 25. 33..3.9 56.2 63.3 70.2 203. 262. 6. 922. 56. 62.2 2092.2 2560.3 302. 396. 396.5 32.5.6 536.7 536.7 630. 6772. 720.9 7709.0 009.3 729.9 59.2 7.9 3.7 0.9 2.2 2.2 59.0 75.0 90.2 20.9 29.0 232.9 26. 259.2 27.9 2.2 296. 353.6 56.3 97.9 605.3 202. 227.7 362.6 57.5 5272. 607.3 6902.2 777. 532.0 936.9 06. 0976.7 79.6 2606.5 32. 795.9 256. WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. 32 3. 63.0 9.6 237. 2.6 322.2 360.3 396.5 3.2 6.3 96. 527. 557.7 57. 66.2 6.2 67.7 0.5 03.2 275.0 363.5 56.9 60.9 255. 002. 99.7 3796.6 563.6 790.5 9337. 2. 2303.3 27.3 26725.2 2572. 309. 39653. 523.2

Vortex In Line Flow Meter Minimum and maximum flow rates to achieve accuracy in M 3 /min ( F C,.03 bar). M 3 /min at actual process temperature = minimum or maximum values below x 273 (actual temp ( F C) + 273). Pipe ID based on schedule 0 steel. Flow Temp 0 F C. TABLE 32 - AIR FLOW RATES AT SELECTED PROCESS PRESSURES (Metric) Size (mm) 20 25 0 50 0 00 50 Density (kg/m3).293.93 2.56 3. 5.2 6.39 7.67.95 0.22.5 2.77.05 5.32 6.6 7. 9.5 22.9 26. Pressur e (barg) 0 0.5 2 3 5 6 7 9 0 2 3 7 20 min max min max min max min max min max min max min max 0.05 0.07 0.09 0. 0. 0.6 0. 0.20 0.2 0.23 0.25 0.27 0.2 0.30 0.3 0.33 0.37 0..2.9 2.5 3. 5.07 6.33 7.59.6 0.2.3 2.6 3.9 5.7 6.3 7.70.96 22.75 26.5 0.09 0.2 0. 0. 0.22 0.26 0.29 0.32 0.35 0.3 0. 0. 0.6 0.9 0.5 0.5 0.6 0.67 2.0 3.. 6.25.33 0.0 2..55 6.62.70 20.77 22.5 2.92 27.00 29.07 3.5 37.37 3.59 0.22 0.29 0.35 0.6 0.55 0.6 0.73 0.0 0. 0.95.02.09.5.2.2.3.5.67 5.2 7.7 0.35 5.9 20.6 25.7 30.92 36.06.20 6.3 5. 56.62 6.76 66.9 72.05 77.9 92.6 0.0 0.37 0. 0.5 0.76 0.92.07.2.3.6.5.70..92 2.02 2.3 2.23 2.5 2.7.69 2.97 7.26 25.2 3.39 2.96 5.53 60.0 6.67 77.2 5.0 9.37 02.9.5 20.0 2.65 5.35 0.06 0.3.0.3.7 2.07 2.0 2.7 3.00 3.2 3.55 3..06.30.5.77.99 5.63 6.2 9. 29.0 3.69 57.90 77. 96.32 5.5 3.75 53.96 73.7 92.3 2.59 230. 250.02 269.23 2. 36.0 03.7.. 2.2 2.9 3.6.9.72 5.23 5.72 6.9 6.6 7.07 7.9 7.90.30.69 9. 0. 33.92 50.66 67.39 00.5 3.3 67.77 20.2 23.70 26.6 30.63 335.09 36.55 02.0 35. 6.9 502.0 602.79 703. 3.27.27 5.6 6.75.7 9. 0.70.6 2.96.0 5.03 6.02 6.9 7.90. 9.69 22.2 2.6 76.6.76 52.66 22.7 30.2 30.09 55.90 53.7 607.52 63.33 759. 3.95 90.76 96.57 062.3 3.9 365.62 593.05 ANSI Flange Pressure - Temperature Ratings. Maximum Pressure in psig. Ambient Temperature Range for Electronics TABLE 33 - FLOW METER PRESSURE RATING TEMP. F F MATERIAL -00 to 00 200 00 500 30L SS/36L SS 50# RF 230 95 75 60 5 0 30L SS/36L SS # RF 505 55 5 30 360 30L SS/36L SS # RF 200 05 90 25 765 720 30L SS/36L SS # RF 500 500 360 20 5 00 30L SS/36L SS 500# RF 500 500 500 500 500 500 33 WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. BULLETIN EM20050

Vortex In Line Flow Meter TABLE 3 Flange Mounting BULLETIN EM20050 Meter Size Flange Rating Bolt diameter Bolts I.D. O.D. W H in. psi in. no. in. in. in. in. 3/ 50 500 50 500.5 50 500 2 50 500 3 50 500 50 500 6 50 500 /2 7/ 7/ /2 /2 3/ 3/7 -/ -/ 3/ 3/ -/ 3/ 7/ -/ -3/ 3/ 7/ -/ -/2 2 2 2 2 Wafer Mounting 0.72 3.75.625.625 5.25 5.25 0.957.25.75.75 5.75 5.75.50 5.00 6.25 6.25 7.00 7.00.937 6.00 6.50 6.50.50.50 2. 7.50.25.25 9.50 0.50 3.26 9.00 0.00 0.75.50 2.25 5.76.00 2.50.00 5.00 5.50 5. 6.25 6.25 7.25 7.25 6.3 6.63 6.63 7.5 7.5 6.63 7.3 7.25.25.25 6.75 7.25 7.50 9.75 9.75 7.25.00.25 9.75.00.25 9.00 0.25.25 2.00 9.75 0.50 2.00 3.75 6.25 9.75 0.25 0.25 0.375 0.375 9.95 0.27 0.27 0.76 0.76 0.35 0.9 0.9.35.35 0.75.25.25 2.25 2.25.60.9.9 2.60 3.0 2.37 2.7 3.25 3.62 3.93.3 5.06 5. 6.3 6.65 Meter Size Flange Rating Bolt diameter TABLE 35 Bolts I.D. O.D. W H in. psi in. no. in. in. in. in. 3/ 50 50.5 50 2 50 3 50 50 6 50 /2 /2 /2 3/ 3/ 3/ 3/ 3/ 7/ 3/ 7/ 2 2 0.72 2.370 2 9.00 0.957 2.70 2 9.20.500 3.500 2 9.60.937.250 2 0.00 2. 5.97 2 0.60 3.26 6.997 2.5.37 5.76.72 3 3.25 WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. 3

Vortex Insertion Flow Meter Principles of Operation Vortices are created when a fluid passes around a bluff body as shown below. Vortices are alternately shed on each side of the body, 0 degrees out of phase to each other, resulting in an oscillating pressure gradient. As flow increases the frequency of vortices increases in proportion to the increased flow thereby creating a linear relationship. Aalborg s unique dual signal processing technology independently measures each vortex on either side of the bluff body and filters out non-flow noise. This results in less noise and higher accuracy throughout the flow range. Benefits RELIABLE WIDE RANGEABILITY HIGH ACCURACY No moving parts to wear or fail. Electronics can be remote mounted up to 00 ft. (30.5 m) No fluid to sensor contact. No holes to clog. High flow turndown ratio up to 0:. Dual signal processing technology improves accuracy at low flows. + 0.5% of rate. Increased noise cancellation as a result of dual signal processing technology. Vortex Insertion Flow Meter shown with fixed mounting Vortex Insertion flow meter shown with retractable mounting Functional Specifications FLUID TYPES Steam, Gas, Liquid. MAXIMUM PRESSURE FLUID TEMPERATURE LOW FLOW CUT-OFF HIGH FLOW CUT-OFF VOLTAGE FREQUENCY OUTPUTS 500 psig (03 bar) see Table 36 for flange ratings. -00 F to 50 F F std. to O F opt. (-73 F to 232 F C std., to 36 F C opt.) Adjustable: Set @ min. per Tables 37 to 39. Adjustable: Set @ max. per Tables 37 to 39. 5 30 VDC or 5/230 VAC (optional). 50/60 Hz. Analog: -20 ma DC into ohm or less. LINEAR RANGE Reynolds number of >0,000. Figure Dual signal processing technology independently measures each vortex providing increased accuracy and turndown. 35 WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. BULLETIN EM20050

Vortex Insertion Flow Meter Performance Specifications ACCURACY REPEATABILITY FLOW TURNDOWN RATIO RESPONSE TIME DAMPING VELOCITY RANGE AGENCY APPROVALS* + 0.5% of rate. + 0.25% of rate. See Tables 37 to 39. 0.5 sec. Adjustable: to 0 sec. Liq.:.32 or 0000µ to 30 ft/sec ñd 2 Steam & Gas: (/ρ)/3 to 250 ft/sec ρ= density (lb/ft3) d= pipe diameter (in) µ= viscosity (cp) FM and CSA Class Div 2 Groups B,C,D. *Designed to meet. Contact Aalborg for status of the agency approval. Ambient Temperature Range for Electronics Figure 2 Physical Specifications MATERIALS OF CONSTRUCTION SHEDDER BAR ELECTRODES METERING TUBE FLANGES ELECTRONICS HOUSING 30 SS or 36 SS. 30 SS or 36 SS encapsulated ceramic. 30 SS or 36 SS. 30L SS or 36L SS. Epoxy coated aluminum. CONNECTIONS AND MOUNTINGS MOUNTING POSITION TYPICAL STRAIGHT PIPE REQUIREMENTS PROCESS CONNECTIONS ELECTRICAL CONNECT Vertical, horizontal, angle. Upstream: 20 x D. Downstream: 5 x D. MNPT, ANSI Class 50 RF, RF, RF, RF, 500 RF welded flange, DIN. 3/ FNPT. Electronic Specifications AMBIENT TEMPERATURE TRANSMITTER -5 F to 0 F F (-2 F to 2 F C). Microprocessor-based. DISPLAY Two lines, simultaneous rate and total, 6 alphanumeric characters each. FUNCTIONS OUTPUT SIGNAL ENCLOSURE PROTECTION Zero, span, hi cutoff, low cutoff, flow rate units, response time, sample time, and engineering units, data logger, RS-232 interface. -20mA into Ohm or less. 5V TTL pulse output. Use or 20 gauge twisted pair shielded cable. NEMA X/IP 66. ENCLOSURE APPROVALS* UL, CSA, FM Class I Groups B, C, D Class II Groups E, F, G KEMA/CENELEC EEx d IIB BULLETIN EM20050 *Designed to meet. Contact Aalborg for status of the agency approval. WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. 36

Vortex Insertion Flow Meter Flow Meter Pressure Rating ANSI Flange Pressure - Temperature Ratings. Maximum Pressure in psig. TABLE 36 - FLOW METER PRESSURE RATING TEMP. F F MATERIAL -00 to 00 200 00 500 30L SS/36L SS 50# RF 230 95 75 60 5 0 30L SS/36L SS # RF 505 55 5 30 360 30L SS/36L SS # RF 200 05 90 25 765 720 30L SS/36L SS # RF 500 500 360 20 5 00 30L SS/36L SS 500# RF 500 500 500 500 500 500 Flow Ranges Minimum and maximum flow rates to achieve accuracy. Pipe ID based on schedule 0 steel. TABLE 37 - WATER FLOW RATES AT 60 F F " 5" 6" " 0" 2" " min max min max min max min max min max min max min max GPM 52. 90.3 2. 7.6. 270. 205.7 675.0 32. 7372.0 60.5 066.3 556.6 26.9 L/MIN 9.2 505.6 3.7 70.7 9.9 022.3 77.6 7696. 227. 27905. 73.2 396. 206.7 70. 6" " 20" 2" 30" 36" min max min max min max min max min max min max GPM 727. 652. 920.3 2095. 3.7 2599.0 65.2 37595. 262.5 596.2 35.6 596.2 L/MIN 2752.2 6259.0 33.5 7969.9 329. 9395.3 626.6 230. 993.6 22576.9 556.7 33033.6 37 WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. BULLETIN EM20050

Vortex In Line Insertion Flow Meter Flow Meter Minimum and maximum flow rates to achieve accuracy in (lb/hr). Pipe ID based on schedule 0 steel. Pressure (psig) 0 25 50 75 00 25 50 200 250 350 00 50 500 550 TABLE 3 - SATURATED STEAM FLOW RATES AT SELECTED PROCESS PRESSURES (English) " 6" " 0" 2" " 6" " 20" min max min max min max min max min max min max min max min max min max 257.3 36. 70. 577.5 67.3 76.0.7 005.6 5.5 29.0 20. 56.7 669.2 7. 905.0 209.2 2.3 75. 902.2 6206. 206.9 2663.6 272.3 3722.0 5635.6 505. 625.2 7039. 79639.6 327.5 9703.0 05966.0 0.7 5.2 739. 90.0 060.2 20. 33. 5.2 0.7 2026. 2233.5 232. 262.6 22.2 2995.5 375. 75. 22.0 75.0 252.9 3250.7 37.0 539. 5559.3 7757. 90. 9303.6 70. 25225. 36.0 526.6 66620.7 5.0 75.3 066.7 30. 530. 733. 925. 222.0 263. 2925.0 3223.3 3509.9 377.7 05. 322.9 52. 090.7 706.0 2700. 36776.0 639. 55967. 655.0 50. 03557.7 2260. 6.3 620.2 0720.5 20035.5 22039. 206.2 0. 360.0 7.3 2269. 269. 2.6 3335. 3952.0 525. 5065.6 552. 607. 6559.6 702. 76.5 7935. 97.2 2956. 6773.9 636. 0353.6 9692.6 36.3 6356. 793. 2239.9 256.2 2797. 32972.7 375. 360.5 63.9 593.9 23. 29. 3576.6 76.0 732.0 5256. 622.3 732.0 793.3 797.3 9579.5 0337. 076.6 79.7 2506. 2960.7 656.9 7375. 00373.2 26636. 52752.5 79.0 230656.3 226. 33725. 37203.0 39976.5 9322. 5705. 600. 656293.7 2262.9 303.0 33.3 5077. 592. 67.2 762.3 2. 025.5 33. 29.7 3.3 676.9 5725. 6750.9 7755.2 2393.9 6609. 0655.7 2502. 7979.5 2666.7 2537.0 3276.7 0273. 7527.9 59722. 6266. 700269.6 776662.6 5325.2 93757.3 273. 3677.6 995.3 636.7 765.2 9.2 90. 066. 2237. 3697.7 509. 636.5 7737.7 5.3 202. 25.0 523.9 7996.0 260. 72220.2 2723.2 262092.6 3067. 395759. 955.9 5732.0 66362.5 759.2 6305.5 93629.7 033.9 2606.2 3572.6 0.3 6525.7 06. 9360. 0606.7 7. 3960. 596.2 79.2 97. 272. 237.9 227.9 266.2 203.9 6693.5 0373. 65230.2 2292.6 235. 323. 005. 57007. 633529.7 750273.3 67. 9690.2 055.5 22693.7 307. 7056.9 522.0.9 259.7 07.0 7.7 325.2 92.0 7670.0 2023. 2269.2 295.6 2777. 29329.3 325.3 3373.7 350. 77.0 320.2 20936.3 2766.5 35927.3 33370.7 507323.3 6539. 075.6 996.0 0952. 227. 39936.0 552026.3 706222. 6956.2 Minimum and maximum flow rates to achieve accuracy in (kg/hr). Pipe ID based on schedule 0 steel. TABLE 39 - SATURATED STEAM FLOW RATES AT SELECTED PROCESS PRESSURES (Metric) Line Size (mm) 00 50 200 250 350 00 50 500 Pressure (bara) min max min max min max min max min max min max min max min max min max BULLETIN EM20050 2 6 0 22 26 2 30 32 3 36 3 0 73. 3. 7. 225.0 30. 35. 53.2 56.6 576.7 605. 63. 662. 690.0 77.3 7.2 770. 329.7 253.6 72.5 739. 59.7.6 20. 2. 29303.6 357.7 3303.2 36069. 339.0 06.7 299. 5270.6 5. 77. 27.2 353..7 606.0 72.7 2. 906.9 952.6 997.5 0.6 05. 27.9 70.2 22.0 2090.9 3999.7 766.9 226.0 227.6 2566. 320.7 39066.7 6079. 9607.9 535.6 567. 60302. 6390.0 67536.2 76. 66.6 256.7 396.0 50. 705.6 7.9 029. 73.0 309. 375.5 0.3 50.0 566.7 62.5 69.6 79.9 30.9 577.9 062.5 620.6 2637. 36336. 639.7 5606. 6653.0 7625.9 7676.9 93.0 7067.6 92273.0 975.6 0272. 2.. 65.5.3 22.6 5.7 7.5 2030.7 2266.9 23.3 293. 2603.7 272.2 29.3 2925.0 3029.5 5226. 9997.6 95.7 2060.7 556.9 62907. 02.7 9765.6 50.0 2000.5 3266.0 775.0 50733.5 5975.2 6. 77939.3 5.5 700. 00. 393.7 925.3 237.3 207. 3200.5 3572.9 3753.0 3929.9 03.6 27.7 3. 60. 77.7 237.2 5757.0 30.5 225. 709. 996.5 2667. 53906. 532.6 953.2 20907. 223.3 237567.6 25770.7 26606. 206. WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. 3 65.3 99.5 533.9 97.7 2733.5 339. 396.5 5.0 5072.7 532.5 5579.5 526.2 6069.2 630.7 655.3 6779. 695.0 2237.5 255. 62790. 0953. 0766.2 79555.5 253. 257736.3 27773.6 2973.9 3727. 337293.7 3575.9 377752.9 397.6 779.9 20.9 53. 239. 3303.6 096.3 7.9 59.7 630.7 639. 673.2 70.3 733.9 762. 790.3 92.9 3. 27037.3 5793.3 756. 2326.3 702.2 27003.3 2605.9 39.3 33533.0 3593. 332.0 07639.2 3200.0 56536. 23.7 0.9 570. 22.7 32. 35. 535.3 6293.9 77.2 00.9 2.7 09. 99.6 952. 9960.3 0333. 0703.0 6. 35320.7 6766.2 9935. 60966.2 22225.3 236. 399.2 06920.6 302. 6903.7 5007.3 53252.0 56365.3 59605.9 6263.6 29.6 97.3 3065.3 395.2 562.6 6773.2 7966..6 037. 06.3 9.9 62.9 22. 2607. 3079. 357.0 23370.9 706. 560. 2579. 203739.6 2302.3 357.5 36669.2 5505.3 5593.7 593. 633976.3 67036.3 7333.7 75.5 795692.6

Vortex Insertion Flow Meter Flanged Insertion Meter /2 MNPT Insertion Meter Note Note /2 Insertion Meter Assembly with Insertion Tool and Ball Valve Note Note Length dependent on pipe diameter, thickness, and mounting. 39 WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. BULLETIN EM20050

Vortex Insertion Flow Meter Minimum and Maximum Flow Rates to achieve Accuracy in CFPM (77 PSIA and 60 F F). PipeID Based on Schedule 0 Steel. DENSITY (lb/ft3) 0.076 0.03 0.2 0.0 0.232 0.2 0.336 0.3 0.0 0.93 0.55 0.596 0.69 0.700 0.752 0.0 0.56.6.636 PRESSURE (PSIG) 0 5 0 20 30 0 50 60 70 0 90 00 0 20 30 0 50 200 TABLE 0 - AIR FLOW RATES AT 60 F F CONDITIONS. " 6" " 0" 2" " min max min max min max min max min max min max 59.2 7.9 3.7 0.9 2.2 2.2 59.0 75.0 90.2 20.9 29.0 232.9 26. 259.2 27.9 2.2 296. 353.6 56.3 97.9 605.3 202. 227.7 362.6 57.5 5272. 6037.3 6902.2 777. 532.0 936.9 06. 0976.7 79.6 2606.5 32. 795.9 256. 3. 63.0 9.6 237. 2.6 322.2 360.3 396.5 3.2 6.3 96. 527. 557.7 57. 66.2 6.2 67.7 0.5 03.2 275 363 562 609 256 003 950 3797 56 790 9337 2 2303 27 26725 2572 309 3965 523 257. 32.9 363. 56. 50.3 6.2 69. 760.9 27. 9.3 952.9 02.7 070. 27.3 2. 236.3 29.0 53.2 9.9 52 693 756 230 56 939 22936 26 26 3357 376 066 206 775 5296 5 536 76 560 05 93 573 79 52 97 09 99 30 05 502 596 6 777 6 99 2032 225 329 2 007 302 939 2977 3056 3652 70 732 5295 550 609 69979 75266 05 62 92030 996 756 576 700 02 209 33 57 702 5 99 232 2265 2396 2522 265 2766 2 32 659 5625 959 27523 355 336 537 5929 67 753 30 90976 9907 0639 77 22703 3063 70293 29609 696 6 9 23 6 672 70 205 223 20 2577 2739 296 309 39 333 36 60 536 093 7 236 3326 255 523 62030 76 205 90792 00379 09967 955 292 3729 37 5790 20 307 DENSITY (lb/ft3) 0.076 0.03 0.2 0.0 0.232 0.2 0.336 0.3 0.0 0.93 0.55 0.596 0.69 0.700 0.752 0.0 0.56.6.636 PRESSURE (PSIG) 0 5 0 20 30 0 50 60 70 0 90 00 0 20 30 0 50 200 TABLE 0 - AIR FLOW RATES AT 60 F F CONDITIONS. 6" " 20" 2" 30" 36" min max min max min max min max min max min max 909 05 25 62 90 2 22 26 2923 3 3366 3577 372 392 77 367 553 53 70 07 2669 30930 352 5597 697 09 935 06063 56 30 3630 5652 6675 97 9379 20622 2653 39076 5 399 627 200 26 276 309 302 3699 395 26 52 7 500 527 552 5763 67 75 23 3225 3950 55000 705 670 02552 02 3253 5003 65953 0 9765 23505 229355 25205 26056 30307 92 30 73 202 2536 2 33 3 227 597 952 5295 5627 599 6263 6569 669 762 56 02 2953 300 6 63 039 07735 273 727 6622 65 2062 225909 25605 26530 2996 30692 3237 2266 6923 206 25 292 3667 32 967 5555 6 669 762 765 3 60 905 9502 993 035 236 5950 75 56 70362 9 27335 552 30 2279 22 269767 2925 3267 355227 3373 2200 067 6973 6606 967 35 203 7 630 7257 303 927 0220 3 972 200 3603 33 52 52 6606 73 2066 2666 69995 9303 76 65227 223 26059 30075 35569 03307 50923 9539 5655 59377 637 63 73669 7235 02235 97 0 57 6799 52 0096 55 299 2 56 6655 709 92 20009 2065 22095 2302 207 27 37090 97377 309 63620 22963 29606 3623 259 93 56077 627320 693503 75906 260 9229 9553 02777 09020 2223 20663 BULLETIN EM20050 WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. 0

Vortex Insertion Flow Meter Ordering Information Please return completed application data sheet found on Aalborg s web site www.aalborg.com to allow us to confirm selection.. Select style (wafer, flange or insertion). 2. Select meter size to match internal pipe diameter (for insertion style select pipe diameter). 3. Confirm minimum and maximum flow ranges to maintain stated accuracy from liquid, steam, or air from Tables 2 to 32 are within your requirements.. For other gas applications consult factory. 5. Select fluid type. 6. Select maximum temperature capability. 7. Select desired material of construction.. Select mounting connection. 9. Confirm maximum pressure capability of flange/meter rating with process conditions and select flange rating from Table 33. 0. Confirm suitability of standard local mounted electronics.. Select desired transmitter power. 2. Provide: Fluid, Fluid Viscosity, Minimum & Maximum Operating Pressure, Minimum & Maximum Operating Temperature, Density/Specific Gravity or Specific Volume. 3. Provide minimum and maximum flow range. Options Remote mount electronics up to 00 ft. (30.5 m) Materials of construction. WWW.AALBORG.COM - E-MAIL : INFO@AALBORG.COM - PHONE 5.770.0 - TOLL FREE IN U.S.A. AND CANADA.00.66.337 - ORANGEBURG N.Y. U.S.A. BULLETIN EM20050