Campbell Fittings Table of Contents Click on the section you want Contents Clips, Forged Wire Rope Eyebolts Eyes, Lifting Hooks, Grab/Slip Hooks, Hoist Hooks, Latch Kits For Links Links, Clevis Links, Connecting Nuts, Eye Shackles Swivels Thimbles Turnbuckles The Campbell operation facilities in York, PA, and Cortland, NY, conform to Quality Standard ISO 00.
FITTINGS Carbon and Alloy Steel Fittings Standards CooperTools forges Campbell fittings under established quality control procedures. Dimensional tolerances meet standards adopted by the Drop Forging Association as outlined in Standard Practices and Tolerances for Impression Die Forgings. Working load limits for carbon and alloy steel fittings are based on predetermined design factors. Working Load Limit. This is the related capacity. It is the maximum load which should ever be applied to the fittings in service, even when they are new. Proof Test. This is a term designating a quality control tensile test applied to the fitting during ar subsequent to the process of manufacture. It is the minimum force in pounds which the fitting has withstood in the condition and at the time it left the factory, under a test in which a constantly increasing force has been applied in direct tension to the fitting on a standard test machine. Ton. Where ton is used in this catalog, it refers to short ton or 2,000 pounds. : Do not exceed Working Load Limit. Most of the fittings in this catalog are intended to be used in conjunction with other components in a load sustaining system. Care should be taken to select components of compatible type, grade, size and working load limit. Any abuse, misuse or alteration of the fitting may lessen the load that the fitting will sustain. Some examples of such changes and abuses are as follows: Twisting or side loading. Disfigurement. Deterioration of the fitting caused by strain, usage or corrosion. Shock loading. Use for a purpose other than that for which the particular fitting was intended. Use to carry a load in excess of the Working Load Limit. A continual inspection program should be undertaken to discover gouges, distortion, cracks, elongation or stretching, spread in the throat, opening of hooks, severe wear, or other damage. CooperTools does not accept any liability for damages which may result from alteration, misuse or abuse of the product or from use in excess of the Working Load Limit. Key to Figure Number Designations S Self-Colored G Galvanized A Alloy H Heat Treated NOTICE: The product specifications and dimensions are as accurate as possible at the time of printing. However, because we are constantly improving the quality and design of our products, they can change without notice. Stainless Forged Fittings Campbell stainless forged fittings are used in place of carbon steel fittings for marine and food processing applications and where fittings are exposed to oxidizing acids, alkalis, neutral brines and detrimental temperatures. They have won wide acceptance in aviation, boating, cements, chemicals, fertilizers, fishing, food processing, hydrodynamics and nuclear energy. Many are used in the fields of oceanography, petroleum, pulp and paper manufacturing, sewage disposal, textiles, water purification and yachting. All stainless fittings are made of Type 6 stainless steel and have an electro-polished finish for improved stress relief, surface appearance and resistance to corrosion and chemical attack. NOTICE: The product specifications and dimensions are as accurate as possible at the time of printing. However, because we are constantly improving the quality and design of our products, they can change without notice.
FITTINGS Forged Wire Rope Clips 000-G Forged Stainless Steel 00 Malleable Iron READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING THESE WIRE ROPE CLIPS. Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Prepare wire rope end termination only as instructed. Do not use on plastic coated wire rope. Periodically inspect assembly for wear and abuse, and tighten nuts to recommended torque. If worn, distorted or damaged, discard and replace. Always stand clear of loads being lifted. Campbell forged carbon steel wire rope clips meet the design requirements of Federal Specification FF-C-40, Type, Class. The base is drop-forged. All parts are galvanized to ASTM A- specification. The U-bolt is dyed blue for identification. Campbell stainless wire rope clips are all drop-forged and made of Type 6 Stainless Steel, and have an electro-polished finish. Wire rope clips are used for making eye termination assemblies. IMPORTANT: Instructions For Use 4. IMPORTANT! Apply the initial load to test the assembly. This load should be equal or greater weight than loads expected in use. Retighten nuts to recommended torque. Periodically, inspect assembly and tighten nuts to recommended torque. The efficiency rating of a properly installed clip is based upon the catalog breaking strength of wire rope. The efficiency rating for clip sizes /8" through /8" is 80% and for sizes " through 2" is 0%. When a pulley is used in place of thimble for turning back the rope, one additional clip should be added. The minimum number of clips shown in the table is based on using right or lang lay wire rope, 6x class, or 6x class, IWRC or fiber core, IPS or EIPS. If Seale construction or similar large outer wire type construction in the 6x class is being used for " and larger wire rope, one additional clip should be added. The minimum number of clips shown in the table can be used with right regular lay wire rope, 8x class, fiber core IPS or IPS for -/2" and smaller wire rope. The number of clips shown also applies to right regular lay wire rope 8x class, fiber core IPS or XIPS for - /4" and smaller wire rope. For classes of wire rope not mentioned, additional clips may be necessary to make a proper termination. Do not use on plastic coated wire rope. L Clip Minimum Amount of Rope Torque Size, No. of to Turn Back Foot Weight in. mm Clips in. mm lb kg /8 2 /2 8 2 /6 2 4 02 8 4 /4 6 2 2 /6 8 2 /2 40 0 4 /8 0 2 6 /2 6 4 20 /6 2 8 6 0. Turn back specified amount of rope per clip size (shown in the table below) from the thimble. Install clip on base width from dead end of rope (U-bolt over dead end). Tighten nuts evenly to recommended torque. 2. Assemble the next clip as close to the loop as possible. Turn nuts alternately and firmly until the ropes make contact.. If any additional clips are required, they should be equally spaced between the first two. Tighten all nuts evenly on all clips to recommended torque (see table). /2 /2 22 6 0 /6 4 2 0 4 /8 6 2 0 4 /4 4 8 4 0 /8 22 4 48 22 02 2 26 660 22 02 /8 2 6 4 864 22 02 /4 2 44 8 60 6 /2 8 8 4 2 60 6 /4 44 8 6 4 0 268 2 8 80 0 4 NOTE: If more clips are used than specified in the table above, the amount of rope turnback should be increased accordingly. The data above based on use of Brewer-Titchener forged wire rope clips on new rope.
FITTINGS 000-G, Wire Rope Clips (Forged Carbon Steel, Galvanized) Standard Material: Base is drop-forged carbon steel, with heavy hex nuts Standard Finish: Galvanized to ASTM A- specification Other Features: Meets specification FF-C-40, Type, Class Note: See application and warning information For Min. Dimensions Rope No. of A Clips Weight/ Dia. Cat. UPC No. Clips UNC-2A B C D E G H Per 00 in. mm No. 02048 Req. in. mm in. mm in. mm in. mm in. mm in. mm in. mm Box lb kg 8 6024 008 2 2 6 4 6 6 4 6 2 2 6 2 00 6 6 604 0 2 6 24 6 4 8 6 2 6 8 8 2 00 0 6044 022 2 6 8 2 26 8 6 2 2 8 2 2 8 2 6 00 8 8 6 8 604 0 2 8 0 6 6 2 8 22 4 6 2 6 4 00 2 8 0 6064 046 2 6 2 8 6 24 2 2 2 2 6 6 4 48 22 6 604 0 2 2 6084 060 6 4 604 0 8 6 604 084 4 624 0 4 8 22 644 00000 4 2 2 8 2 8 2 2 6 40 2 4 0 2 2 2 8 2 8 2 6 2 6 4 2 4 0 6 6 4 2 8 60 8 4 2 2 6 46 2 6 62 0 6 44 6 4 2 8 60 2 8 4 2 2 2 6 2 2 6 62 2 0 48 8 2 4 0 2 8 2 8 2 8 2 6 2 6 2 60 4 0 8 8 48 4 44 2 2 2 64 4 8 2 240 0 2 664 000 8 2 684 00024 6 4 2 6204 000 2 8 6244 00048 8 4 0 2 8 2 2 2 8 48 4 44 2 4 0 8 86 2 20 2 4 0 8 8 2 8 4 2 2 2 2 2 48 6 8 2 0 40 4 8 4 4 08 2 8 60 2 4 2 2 6 4 8 4 02 0 468 22 8 4 6 2 2 4 2 6 6 2 6 6 2 8 4 8 0 600 22 4 44 628 000 8 8 2 6 48 2 4 0 6 8 2 4 0 4 6 Bulk 00 40 2 62 00062 8 4 2 6 2 6 6 8 86 8 4 4 08 8 4 Bulk,20 8 00, Wire Rope Clips (Malleable Iron, Zinc Plated) Standard Material: Base is cast malleable iron with regular hex nuts Note: See application and warning information. Dimensions Case Fig. Size A B C D Cat. UPC No. Shelf Case Wgt. Case No. in. mm in. mm in. mm in. mm in. mm No. 02048 Pack Pack lb kg Cubes 00 8 8 2 2 -- -- T604 206 0 00 2.4 00 6 00 00 6 8 00 8 00 2 00 8 6 00 4 6 6 2 /2 8 6 8 /2 8 6 4 -- -- T6042 200 0 00 24.2 6 -- -- T604 204 0 200 26 2 2.4 6 -- -- T6044 202 0 200 2.4 8 0 2 8 22 -- -- T604 208 0 200 4 2 20.46 2 2 /2 64 2 -- -- T604 204 0 00 40 2 8.4 8 6 2 /4 0 6 0 -- -- T6048 202 0 00 24.4 4 /6 8 2 4 -- -- T604 80460 0 4 2.80 00 C B
FITTINGS M-4-ST, Wire Rope Clips (Stainless Steel) Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish A C E D For Rope Dimensions Diameter Weight A Cat. UPC No. B C D E Clips Per Per 00 in. mm No. 02048 in. mm in. mm in. mm in. mm Fastening in. mm 8 640002 040 2 4 6 4 4 4 2 4 2 6 64000 048 4 8 22 8 2 2 0 640004 042 6 8 2 8 2 8 2 8 8 8 640006 042 2 8 2 8 2 2 2 2 2 640008 044 6 4 2 8 48 2 6 8 40 8 6 64000 046 6 4 2 2 8 4 2 2 64 0 4 Shackles 46-S Round Pin Chain -G, A Safety Anchor Stainless Screw Pin Anchor 4-S, G Screw Pin Anchor 8-G Safety Chain Stainless Safety Anchor 422-G Screw Pin Chain Stainless Round Pin Anchor READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING SHACKLES. Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Use shackles only as indicated. Shackles must always be inspected for wear, distortion and damage before use. If the pin or bow is worn, distorted or damaged, discard the entire shackle and replace. Do not use round pin shackles in rigging applications. Screw pin shackles should not be used if there will be movement on the pin. Movement could cause the pin to unscrew and drop the load. Always stand clear of loads being lifted.
FITTINGS Shackles (continued) Campbell carbon and alloy shackles are all drop-forged. The pins and bolts are made of alloy steel. The shackles all meet the design requirements of Federal Specification RR-C-2, Type IV. Galvanizing is to ASTM A- specification. Campbell Stainless shackles are all drop-forged and made of Type 6 Stainless Steel, and have an electro-polished finish. IMPORTANT: Instructions For Use. Do not exceed working load limit (WLL). See tables below. 2. The standard WLL given applies to in-line loading (perpendicular to the pin). When the loading is at an angle, the WLL is reduced as shown in the table below.. Any angular loads must be on the bow. All straight loading should be on the pin. WLL in Tons Campbell Carbon and Alloy Shackles In-Line Load 4 Load 0 Load Shackle Size, WLL WLL WLL in. mm ton kg ton kg ton kg 6 02 8 6 WLL in Lbs. Campbell Stainless Shackles In-Line Load 4 Load 0 Load Shackle Size, WLL WLL WLL in. mm lb kg lb kg lb kg 000 44 00 8 00 22 2 44 02 4 22 6 8 00 68 00 46 0 6 6 8 80 2 44 02 8 0 2000 0 400 6 000 44 8 0 0 2 60 2 44 6 000 62 200 00 68 8 Alloy 0 2 84 20 0 2 4000 84 2800 20 2000 0 6 2 6 0 80 8 6 6000 222 4200 0 000 62 2 2 84 20 0 2 Alloy 024 2 2 2 6 8 6 4 248 2 4 204 2 6 4 8000 62 600 240 4000 84 8 22 0000 440 000 000 2268 2 2000 44 8400 80 6000 222 4 4 4 40 024 2 2 4 Alloy 60 46 2 8 22 6 2 8 4 2 4082 4 248 2 8 2 6 44 4 4 86 Alloy 2 2 2 8 8 6 68 8 2 2 868 6 2 6048 4 4 40 4 2 2 0886 8 60 6 44 4 Alloy 2 8 626 2 2 8 86 8 2 224 2 868 6 2 2 8 422 8 0 8 2 2 Alloy 8 0 22 2 0 608 8 4 20 844 4 200 0 02 4 Alloy 44 40 628 28 240 2 2 40 2 24 2 22226 2 86 2 Alloy 0 4 2 226 2 2 64 48 8 2 426 2 2 244 6 6808 2 2 462 2 40 2 8 00 08 0 602 0 4
SHACKLES, Anchor Shackles Safety Drop-Forged Carbon Steel and Alloy Steel Standard Material: Shackle bodies are drop-forged carbon steel. Alloy shackles are all alloy steel Standard Finish self-colored or galvanized to meet ASTM A- specifications Working load limit permanently shown on every shackle Design Factor: 6 to -G, safety meets the design requirements of Federal Specification RR-C-2, Type IVA, Grade A, Class -G, Drop-Forged Carbon Steel Galvanized Working Tolerances Dimensions Weight/ Size Cat. UPC No. Load Limit Length Width B C D E F 00 in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg 2 08 020 2 84 8 6 2 8 6 6 4 6 2 4 2 4 2 0 2 8 6 0 044 4 248 8 6 2 4 2 6 62 6 2 6 40 6 0 4 2 068 4 4 40 6 2 8 22 2 6 4 2 6 46 4 44 200 8 22 4 082 6 2 8 2 6 060 8 2 8 2 8 062 2 868 6 2 2 8 6 2 6 2 2 0 0 6 2 8 2 4 6 4 2 2 64 2 8 60 00 22 6 2 4 2 4 4 08 6 46 2 6 2 8 6 0 22 4 2 20 064 2 0886 8 22 066 2 224 2 8 24 068 422 8 4 26 0 20 844 4 44 28 0 2 22680 2 2 066 2 2 6 2 8 4 2 4 2 4 8 6 000 44 8 2 8 4 2 4 2 8 4 8 00 0 8 8 4 4 46 2 8 60 8 8 2 8 600 26 8 4 44 6 4 2 8 6 4 4 08 8 2 200 044 8 2 8 2 8 4 4 2 4 02 280 24 8 2 4 4 4 8 4 46 4 8 24 4000 86 2 2 64 40 0 486 These items are made to order 2 -A, Alloy Steel Galvanized 8 2 4 0 0 6 268 4 8 0 4 84 2 40 000 4086 Working Tolerances Dimensions Weight/ Size Cat. UPC No. Load Limit Length Width B C D E F 00 in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg 2 08 828 024 8 6 2 8 6 6 4 6 2 4 2 4 2 0 2 4 2 820 60 6 2 8 22 2 6 4 2 6 46 4 44 200 2 6 822 2 2 40 4 2 20 822 8 62 2 8 24 068 0 226 4 44 28 042 40 6288 2 2 0 0 460 2 6 2 8 2 4 6 4 2 2 64 2 8 60 00 22 6 2 8 4 2 4 2 4 8 6 000 44 8 8 4 4 46 2 8 60 8 8 2 8 600 26 8 2 8 2 8 4 4 2 4 02 280 24 8 2 4 4 4 8 4 46 4 8 24 4000 86
SHACKLES Anchor Shackles Safety Type 6 Stainless Steel Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish Working Tolerances Dimensions Weight Size Cat. UPC No. Load Limit Length Width B C D E F Each in. mm No. 02048 lb kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg 6402404 084 000 44 6 2 6 2 6 8 8 2 2 4 6 0.0 0.0 6 8 640240 082 00 68 6 2 6 2 8 0 4 2 2 2 2 2 4 0.6 0.0 8 6402406 086 2000 0 8 6 2 6 6 2 2 2 2 6 24 0.20 0.0 6 640240 086 000 62 8 6 2 2 4 44 2 2 8 2 2 8 2 0.0 0.2 2 6402408 088 4000 84 8 6 2 8 6 6 4 6 2 4 2 4 2 0.2 0. 8 6 640240 080 6000 222 8 6 2 4 2 6 62 6 2 6 40 6.8 0.6 4 640242 006 8000 62 6 2 8 22 2 6 4 2 6 46 4 44 2.22.0 8 22 640244 0 0000 440 2 640246 020 2000 44 6 2 2 6 6 46 4 44 2.22.0 6 2 8 2 4 6 4 2 8 4 2.28.4
SHACKLES 4, Anchor Shackles Screw Pin Drop-Forged Carbon Steel and Alloy Steel Standard Material: Shackle bodies are drop-forged carbon steel. Alloy shackles are all alloy steel Standard Finish self-colored or galvanized to meet ASTM A- specifications Working load limit permanently shown on every shackle Design Factor: 6 to 4-S, 4-G Screw Pin meets the design requirements of Federal Specification RR-C-2, Type IVA, Grade A, Class 2 4-S, Drop-Forged Carbon Steel Self Colored Working Tolerances Dimensions Weight/ Size Cat. UPC No. Load Limit Length Width B C D E F 00 in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg 4040 064 2 44 6 2 6 2 6 8 8 2 2 2 2 2 20 6 0 6 8 400 066 80 6 2 6 2 8 0 4 2 2 2 2 2 4 8 8 8 0 4060 06206 0 8 6 2 6 6 2 2 2 2 6 24 0 4 6 400 062 2 6 8 6 2 2 4 44 2 2 8 2 2 8 2 2 24 2 4080 06268 2 84 8 6 2 8 6 6 4 6 2 4 2 4 2 0 2 8 6 400 06282 4 248 8 6 2 4 2 6 62 6 2 6 40 6 0 4 420 060 4 4 40 6 2 8 22 2 6 4 2 6 46 4 44 200 8 22 440 062 6 2 8 2 460 064 8 2 8 2 480 066 2 868 4 2 4200 068 2 0886 8 4220 06404 2 224 2 8 4240 06428 422 4 44 4280 064 2 22680 2 420 064 2 2 2 64 4400 060 486 2 2 6 2 2 8 6 2 6 2 2 0 0 6 2 8 2 4 6 4 2 2 64 2 8 60 00 22 6 2 4 2 4 4 08 6 46 2 6 2 8 6 0 22 6 2 8 4 2 4 2 4 8 6 000 44 8 2 8 4 2 4 2 8 4 8 00 0 8 8 4 4 46 2 8 60 8 8 2 8 600 26 8 2 8 2 8 4 4 2 4 02 280 24 8 2 4 4 4 8 4 46 4 8 24 4000 86 8 2 4 0 0 6 268 4 8 0 4 84 2 40 000 4086
SHACKLES 4, Anchor Shackles - Screw Pin continued Drop-Forged Carbon Steel Galvanized Working Tolerances Dimensions Weight/ Size Cat. UPC No. Load Limit Length Width B C D E F 00 in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg 6 40 068 02 6 2 6 2 8 22 8 0 2 6 4 2 404 066 2 44 6 2 6 2 6 8 8 2 2 2 2 2 20 6 0 6 8 40 060 80 6 2 6 2 8 0 4 2 2 2 2 2 4 8 8 8 0 406 06220 0 8 6 2 6 6 2 2 2 2 6 24 0 4 6 40 062 2 6 8 6 2 2 4 44 2 2 8 2 2 8 2 2 24 2 408 062 2 84 8 6 2 8 6 6 4 6 2 4 2 4 2 0 2 8 6 40 062 4 248 8 6 2 4 2 6 62 6 2 6 40 6 0 4 42 062 4 4 40 6 2 8 22 2 6 4 2 6 46 4 44 200 8 22 44 066 6 2 8 2 46 060 8 2 8 2 48 064 2 868 4 2 420 068 2 0886 8 422 064 2 224 2 8 424 064 422 4 44 428 06466 2 22680 2 42 06480 2 2 2 64 440 062 486 2 2 6 2 2 8 6 2 6 2 2 0 0 6 2 8 2 4 6 4 2 2 64 2 8 60 00 22 6 2 4 2 4 4 08 6 46 2 6 2 8 6 0 22 6 2 8 4 2 4 2 4 8 6 000 44 8 2 8 4 2 4 2 8 4 8 00 0 8 8 4 4 46 2 8 60 8 8 2 8 600 26 8 2 8 2 8 4 4 2 4 02 280 24 8 2 4 4 4 8 4 46 4 8 24 4000 86 8 2 4 0 0 6 268 4 8 0 4 84 2 40 000 4086 Anchor Shackles - Screw Pin Drop-Forged Carbon Steel Galvanized - Bagged, per Bag, 0 Bags per Carton Working Tolerances Dimensions Weight/ Size Cat. UPC No. Load Limit Length Width B C D E F Shelf Pack in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg B604 428 2 44 6 2 6 2 6 8 8 2 2 2 2 2 20 6 2 0. 6 8 B60 668 80 6 2 6 2 8 0 4 2 2 2 2 2 4 2..2 8 0 B606 442 0 8 6 2 6 6 2 2 2 2 6 24 4.2. Anchor Shackles - Screw Pin Drop-Forged Carbon Steel Galvanized - Loose, 0 Shackles per Box Working Tolerances Dimensions Weight Size Cat. UPC No. Load Limit Length Width B C D E F Per Box in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg 4044 062 2 44 6 2 6 2 6 8 8 2 2 2 2 2 20 6. 0. 6 8 404 068 80 6 2 6 2 8 0 4 2 2 2 2 2 4 2. 0. 8 0 4064 062 0 8 6 2 6 6 2 2 2 2 6 24.6 6 404 06244 2 6 8 6 2 2 4 44 2 2 8 2 2 8 2 2.2
SHACKLES 4, Anchor Shackles - Screw Pin continued 4-A, Alloy Steel - Galvanized Working Tolerances Dimensions Weight/ Size Cat. UPC No. Load Limit Length Width B C D E F 00 in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg 8 0 406 826 2 84 8 6 2 6 6 2 2 2 2 6 24 0 4 2 408 824 024 8 6 2 8 6 6 4 6 2 4 2 4 2 0 2 4 42 820 60 6 2 8 22 2 6 4 2 6 46 4 44 200 2 46 826 2 2 40 4 2 420 824 8 60 6 2 8 2 4 6 4 2 2 64 2 8 60 00 22 6 2 8 4 2 4 2 4 8 6 000 44 Anchor Shackles Screw Pin Type 6 Stainless Steel Drop-forged Type 6 Stainless Steel Working Tolerances Dimensions Weight Size Cat. UPC No. Load Limit Length Width B C D E F Each in. mm No. 02048 lb kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg 640204 064 000 44 6 2 6 2 6 8 8 2 2 4 6 0.0 0 6 8 64020 066 00 68 6 2 6 2 8 0 4 2 2 2 2 2 4 0.6 0 8 0 640206 068 2000 0 8 6 2 6 6 2 2 2 2 6 24 0.20 0 6 64020 068 000 62 8 6 2 2 4 44 2 2 8 2 2 8 2 0.0 0 2 640208 062 4000 84 8 6 2 8 6 6 4 6 2 4 2 4 2 0.2 0 8 6 64020 008 6000 222 8 4 64022 0 8000 62 6 2 6 2 4 2 6 62 6 2 6 40 6.0 8 22 2 6 4 2 6 46 4 44 2.22 8 22 64024 022 0000 440 2 64026 0 2000 44 6 2 2 8 6 2 8 4 2.28 6 2 8 2 4 6 4 2 2 64 2 8 60. 2
SHACKLES Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish Anchor Shackles Round Pin Type 6 Stainless Steel Working Tolerances Dimensions Weight Size Cat. UPC No. Load Limit Length Width B C D E F Each in. mm No. 02048 lb kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm in. mm lb kg 6402604 040 000 44 6 2 6 2 6 8 8 2 2 4 6 0.0 0 6 8 640260 04026 00 68 6 2 6 2 8 0 4 2 2 2 2 2 4 0.6 0 8 0 6402606 040 2000 0 8 6 2 6 6 2 2 2 2 6 24 0.20 0 6 640260 04040 000 62 8 6 2 2 4 44 2 2 8 2 2 8 2 0.0 0 2 6402608 040 4000 84 8 6 2 8 6 6 4 6 2 4 2 4 2 0.2 0 8 6 640260 04064 6000 222 8 6 2 4 2 6 62 6 2 6 40 6.8 8-G, Chain Shackles Safety Drop-Forged Carbon Steel Galvanized Standard Material: All shackle bodies are drop forged carbon steel. All pins are alloy steel Standard Finish: Self-colored or galvanized to ASTM A- specification Working load limit permanently shown on every shackle Design Factor: 6 to Other Features: Meets Federal Specification TR-C-2 Type VII, Class 8-G, safety meets the design requirements of Federal Specification RR-C-2, Type IVB, Grade A, Class Working Tolerances Dimensions Weight/ Size Cat. UPC No. Load Limit Length Width B C D F 00 in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm lb kg 2 808 020 2 84 8 6 2 8 6 6 4 6 2 4 2 4 8 6 80 024 4 248 8 6 2 4 2 6 2 6 0 4 82 028 4 4 40 6 2 8 22 2 6 4 2 4 44 220 00 2 86 0 8 2 4 2 820 0 2 0886 8 822 0 2 224 6 2 8 2 4 8 6 4 2 8 60 40 204 6 2 8 8 8 2 6 0 422 8 2 8 4 2 4 8 00 4
422, Chain Shackles-Screw Pin Drop-Forged Carbon Steel SHACKLES Standard Material: All shackle bodies are drop forged carbon steel. All pins are alloy steel Standard Finish: Galvanized to ASTM A- specification Working load limit permanently shown on every shackle Design Factor: 6 to Other Features: Meets Federal Specification TR-C-2 Type VII, Class 422-G Screw Pin meets the design requirements of Federal Specification RR-C-2, Type IVB, Grade A, Class 2 Working Tolerances Dimensions Weight/ Size Cat. UPC No. Load Limit Length Width B C D F 00 in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm lb kg 404 060 2 44 6 2 6 2 6 8 8 22 2 2 6 6 8 40 062 80 6 2 6 2 8 0 2 2 6 2 8 8 0 406 064 0 8 6 2 6 4 2 2 2 6 24 0 4 2 408 068 2 84 8 6 2 8 6 6 4 6 2 4 2 4 8 6 40 000 4 248 8 6 2 4 2 6 2 6 0 4 42 002 4 4 40 6 2 8 22 2 6 4 2 4 44 220 00 8 22 44 004 6 2 8 2 46 006 8 2 4 2 420 004 2 0886 6 2 2 2 8 6 2 60 6 6 2 8 2 4 8 6 4 2 8 60 40 204 6 2 8 8 8 2 6 0 422 46, Chain Shackles-Round Pin Drop-Forged Carbon Steel Standard Material: All shackle bodies are drop-forged carbon steel. All pins are alloy steel Standard Finish: Self-colored Working load limit permanently shown on every shackle Design Factor: 6 to Other Features: Meets Federal Specification RR-C-2 Type VII, Class 46-S Round Pin meets the design requirements of Federal Specification RR-C-2, Type IVB, Grade A, Class See chart on top of next page.
SHACKLES 46-S, Drop-Forged Carbon Steel-Self Colored Working Tolerances Dimensions Weight/ Size Cat. UPC No. Load Limit Length Width B C D F 00 in. mm No. 02048 ton kg ±in.±mm ±in. ±mm in. mm in. mm in. mm in. mm lb kg 6 8 4200 068 80 6 2 6 2 8 0 2 2 6 2 8 8 0 42060 062 0 8 6 2 6 4 2 2 2 6 24 0 4 6 4200 066 2 6 8 6 2 2 2 8 2 2 8 8 2 46 2 2 42080 066 2 84 8 6 2 8 6 6 4 6 2 4 2 4 8 6 4200 066 4 248 8 6 2 4 2 6 2 6 0 4 4220 066 4 4 40 6 2 8 22 2 6 4 2 4 44 220 00 Synthetic Sling Shackle-Safety Drop-Forged Alloy Steel Standard Material: Alloy Steel Standard Finish: Painted orange Design Factor: to Increased bow radius provides wider load bearing surface than traditional shackles Allows better load distribution on internal fibers Sling Working Dimensions Weight Width Cat. UPC No. Load Limit A B C D Each in. mm No. 02048 ton kg in. mm in. mm in. mm in. mm lb kg 2 60 826 4 248.8.84..0.688 42.88.06 2.00.. 2 8 62 828 6 2 86.06 2.0.8 22.2 2.00 0.80.2. 4.. 2 64 828 8 4 8.0 26.6.00 2.40 2.8.0.48 6..8 6 68 822 2 2 40.2 28.8.2...2.8 46.0. 4. 4 02 620 808 2 0. 4..0 8.0. 46.0 2.2. 22. 0.0 2 624 8. 44.4 2.00 0.80 6..4 2.8.0. 2.8 6 2 62 822 0 4 2.00 0.80 2.2..00.80.2 82. 8..6
SHACKLES Synthetic Sling Shackle-Screw Pin Drop-Forged Alloy Steel Standard Material: Alloy Steel Standard Finish: Painted orange Design Factor: to Increased bow radius provides wider load bearing surface than traditional shackles Allows better load distribution on internal fibers Sling Working Dimensions Weight Width Cat. UPC No. Load Limit A B C D Each in. mm No. 02048 ton kg in. mm in. mm in. mm in. mm lb kg 2 0 8 4 248.8.84..0.688 42.88.06 2.00.4.64 2 8 2 820 6 2 86.06 2.0.8 22.2 2.00 0.80.2..6.6 2 4 826 8 4 8.0 26.6.00 2.40 2.8.0.48 6. 6. 2.86 6 8 822 2 2 40.2 28.8.2...2.8 46.0 8.2. 4 02 20 820 2 0. 4..0 8.0. 46.0 2.2.. 8.6 2 24 824. 44.4 2.00 0.80 6..4 2.8.0 44.2 20.0 6 2 2 824 0 4 2.00 0.80 2.2..00.80.2 82..8 4.4
HOOKS Hoist Hooks 00, 0-S, G, A Eye Hoist 0, 04-S, G, A Swivel Hoist 02, 06-S, A Shank Hoist READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING HOIST HOOKS. Campbell hoist hooks are all drop-forged and heat treated. All hooks are drilled for latch assembly. Galvanizing is to ASTM A specification. IMPORTANT: Instructions For Use. For hooks with latches, the latch is only designed to retain slings and rigging attachments. The latch must not support the load. 2. Swivel hoist hooks are not designed to swivel under load.. Do not exceed working load limit (WLL). See table below. Working Load Limits Swivels Carbon Steel WLL Alloy WLL Size Ton kg Ton kg 2/22 80 0 /2 0 2 6 4/24 2 6 2 84 /2 2 84 222 6/26 2 2 2268 4 62 /2 222 4 2 4082 8/28 4 62 2 48 /2 46 60 / 2 6804 2 86 608 2 0 02 608 4 608 22 8 *Item not manufactured Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Use hoist hooks only as indicated. Never point load a hook. Do not use hooks for lifting personnel. Hooks must always be inspected for wear, distortion and damage before use. If worn, distorted or damaged, discard and replace. Do not weld on hooks. If a hook is exposed to weld spatter, discard that hook. Always stand clear of loads being lifted.
HOOKS 0, Swivel Hoist Hooks Standard Material: Drop-forged carbon steel or alloy and heat treated Standard Finish: Self-colored or galvanized to ASTM A- specification. Alloy hooks are painted orange Design Factor: to for carbon steel; 4 to for alloy steel Other Features: All hooks are drilled for latch kits Carbon Steel Alloy Steel Painted Orange Self Colored Galvanized Working Working Weight Size Cat. UPC No. Cat. UPC No. Load Limit Cat. UPC No. Load Limit Each No. No. 02048 No. 02048 ton kg No. 02048 ton kg lb kg 2 4020 082 -- -- 80 02 022 0 0.6. 4 4040 080 -- -- 2 6 04 022 2 84.6. 400 084 -- -- 2 84 0 02284 222 2..2 400 0 -- -- 222 0 022 4 2 4082 4.8 2.2 400 0 -- -- 46 -- -- 60.6 4.4 40 0 -- -- 2 6804 020.6 6.2 2 420 020 -- -- 86 2 024 66.6.0 These items are made to order Size A B C D E F S L R No. in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm 2 2 2 4 2 6 2 8 22 8 0 2 40 4 8 4 2 2 64 4 2 2 8 6 0 8 2 2 6 8 4 4 44 4 02 4 2 8 2 2 8 4 44 2 4 6 2 2 6 2 8 8 8 4 8 6 8 2 20 6 6 6 4 6 240 8 20 4 2 4 2 4 2 2 64 6 2 64 6 4 8 4 2 2 2 8 6 246 8 4 2 4 0 8 2 2 6 2 6 2 4 2 8 2 22 2 8 4 2 8 6 8 6 8 2 6 2 8 4 4 2 6 2 40 2 4
HOOKS Standard Material: Drop-forged carbon steel or alloy and heat treated Standard Finish: Self-colored or galvanized to ASTM A- specification. Alloy hooks are painted orange Design Factor: to for carbon steel; 4 to for alloy steel Other Features: All hooks are drilled for latch kits 04, Swivel Hoist Hooks Latched Carbon Steel Alloy Steel Painted Orange Self Colored Galvanized Working Working Weight Size Cat. UPC No. Cat. UPC No. Load Limit Cat. UPC No. Load Limit Each No. No. 02048 No. 02048 ton kg No. 02048 ton kg lb kg 2 4220 020 422 02048 420 020 42 02062 80 22 022 0 0.6. 80 2 028 0 0.6. 4 4240 020 424 02086 2 6 24 024 2 84.6. 420 020 42 020 2 84 2 022 222 2..2 420 020 42 024 222 2 026 4 2 4082 4.8 2.2 420 028 42 028 46 -- -- 60.6 4.4 -- -- -- -- -- -- 026.6 6.2 2 420 022 -- -- 86 2 028 66.6.0 Size A B C D E F S L R No. in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm 2 2 2 4 2 6 2 2 2 64 4 2 2 8 6 8 6 2 8 22 2 2 8 0 2 40 4 8 2 6 8 68 4 4 2 2 64 4 2 2 8 6 0 8 2 2 6 8 4 4 44 4 02 4 2 8 2 2 8 4 44 2 4 6 2 2 6 2 8 8 8 4 8 6 8 2 20 6 6 6 4 6 240 8 20 4 2 4 2 4 2 2 64 6 2 64 6 4 8 4 2 2 2 8 6 246 8 4 2 4 0 8 2 2 6 2 6 2 4 2 8 2 22 2 8 4 2 8 6 8 6 8 2 6 2 8 4 4 2 6 2 40 2 4
HOOKS 02 &06, Shank Hooks Standard Material: Drop-forged carbon steel or alloy and heat treated Standard Finish: Self-colored on carbon hooks; alloy hooks are painted orange Design Factor: to for carbon steel; 4 to for alloy steel hooks Other Features: All hooks are drilled for latch kits Carbon Steel Alloy Steel Self Colored Regular Latched Working Regular Latched Working Weight Size Cat. UPC No. Cat. UPC No. Load Limit Cat. UPC No. Cat. UPC No. Load Limit Each No. No. 02048 No. 02048 ton kg No. 02048 No. 02048 ton kg lb kg 2 -- -- -- -- -- -- 802 026 -- -- 0.6 0. 4 040 024 -- -- 2 6 804 028 -- -- 2 84. 0. 00 02420 -- -- 2 84 -- -- -- -- -- --.8 0.8 00 024 -- -- 222 -- -- -- -- -- --.6.6 -- -- -- -- -- -- 80 026 -- -- 60 6. 2.8 These items are made to order Size A B C D E F G H K L R No. in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm 2 6 4 2 6 2 2 2 8 22 4 8 22 6 4 6 2 2 6 4 2 2 8 2 2 64 8 22 6 0 8 2 2 2 8 2 6 6 4 2 4 0 8 22 2 4 0 2 4 02 4 2 8 2 2 2 6 6 2 6 2 6 8 2 2 4 8 6 4 6 2 2 6 6 8 4 6 2 8 6 2 8 2 2 6 4 6 40 6 2 64 6 4 8 4 6 46 2 8 4 2 4 0 4 260 4 6
HOOKS Standard Material: Drop-forged carbon steel or alloy and heat treated Standard Finish: Self-colored or galvanized to ASTM A- specification Design Factor: to for carbon steel; 4 to for alloy steel Other Features: All hooks are drilled for latch kits 00, Eye Hoist Hooks-Regular Carbon Steel Alloy Steel Self-Colored Self Colored Galvanized Working Working Weight Size Cat. UPC No. Cat. UPC No. Load Limit Cat. UPC No. Load Limit Each No. No. 02048 No. 02048 ton kg No. 02048 ton kg lb kg 22 220 0 22 026 80 222 068 0.4.2 2 20 0 2 040 0 22 064 2 6.2. 24 240 0 24 064 2 6 224 062 2 84.04.4 2 20 0 2 088 2 84 22 066 222.4.66 26 260 0 -- -- 2 2 2268 -- -- -- -- 2.24.02 2 20 028 -- -- 222 22 066 4 2 4082.0. 28 280 022 -- -- 4 62 -- -- -- -- 4.0 2.22 2 20 026 -- -- 46 22 068 60.0. 0 024 -- -- 2 6804 2 060 2.00.4 2 20 0 2 024 0 02 22 006 608.60. 4 -- -- -- -- -- -- 24 0 22 8.0.4 Size A B D E F G H K L R S No. in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm 22 6 4 6 24 2 2 2 26 2 2 2 2 2 20 2 2 2 6 4 4 6 2 8 8 0 2 6 46 6 24 6 8 6 2 2 2 2 2 2 2 2 8 6 4 2 2 8 8 86 6 24 2 8 4 8 2 6 0 8 2 2 26 2 26 8 2 2 2 8 60 4 2 4 02 4 2 8 2 2 2 6 26 2 6 68 8 4 2 4 2 6 8 6 2 8 6 2 4 4 6 2 8 4 4 2 06 6 24 6 6 0 4 2 2 20 2 6 4 2 2 2 2 6 6 40 4 6 2 2 6 6 8 4 6 2 2 2 8 2 2 44 28 8 2 2 2 48 2 4 2 8 8 4 6 4 6 0 8 8 2 6 6 2 4 2 6 2 64 6 4 2 2 42 6 46 2 8 4 2 4 8 2 6 8 6 6 2 8 22 4 4 08 2 2 4 6 8 2 8 4 8 48 2 2 8 60 2 8 0 2 26 2 2 2 4 8 24 2 2 6 8 6 2 2 6 6 2 8 4 2 6 6 2 6 6 46 0 6 2 4 2 4 6 8 62 2 80 6 2 6 8 2 80 2 82 2 2 6 2 2 6 6 2 2 42 2 6 06 8 4
HOOKS 0, Eye Hoist Hooks Latched Standard Material: Drop-forged carbon steel or alloy and heat treated Standard Finish: Self-colored or galvanized to ASTM A- specification Design Factor: to for carbon steel; 4 to for alloy steel Other Features: All hooks are drilled for latch kits Carbon Steel Alloy Steel Painted Orange Self Colored Galvanized Working Working Weight Size Cat. UPC No. Cat. UPC No. Load Limit Cat. UPC No. Load Limit Each No. No. 02048 No. 02048 ton kg No. 02048 ton kg lb kg 22 420 0 42 086 80 242 020 0.4.2 2 40 0 4 040 0 24 0 2 6.2. 24 440 046 44 042 2 6 244 044 2 84.04.4 2 40 040 4 044 2 84 24 0 222.4.66 26 460 044 46 046 2 2 2268 -- -- -- -- 2.24.02 2 40 048 4 048 222 24 068 4 2 4082.0. 28 480 042 -- -- 4 62 -- -- -- -- 4.0 2.22 2 40 0 -- -- 46 24 0 60.0. 0 0 -- -- 2 6804 2 082 2.00.4 2 20 0 -- -- 0 02 22 0 608.60. 4 -- -- -- -- -- -- 24 080 22 8.0.4 Size A B D E F G H K L R S No. in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm 22 6 4 6 24 2 2 2 26 2 2 2 2 2 20 2 2 2 6 4 4 6 2 8 8 0 2 6 46 6 24 6 8 6 2 2 2 2 2 2 2 2 8 6 4 2 2 8 8 86 6 24 2 8 4 8 2 6 0 8 2 2 26 2 26 8 2 2 2 8 60 4 2 4 02 4 2 8 2 2 2 6 26 2 6 68 8 4 2 4 2 6 8 6 2 8 6 2 4 4 6 2 8 4 4 2 06 6 24 6 6 0 4 2 2 20 2 6 4 2 2 2 2 6 6 40 4 6 2 2 6 6 8 4 6 2 2 2 8 2 2 44 28 8 2 2 2 48 2 4 2 8 8 4 6 4 6 0 8 8 2 6 6 2 4 2 6 2 64 6 4 2 2 42 6 46 2 8 4 2 4 8 2 6 8 6 6 2 8 22 4 4 08 2 2 4 6 8 2 8 4 8 48 2 2 8 60 2 8 0 2 26 2 2 2 4 8 24 2 2 6 8 6 2 2 6 6 2 8 4 2 6 6 2 6 6 46 0 6 2 4 2 4 6 8 62 2 80 6 2 6 8 2 80 2 82 2 2 6 2 2 6 6 2 2 42 2 6 06 8 4
HOOKS 48-G Snap Hooks Standard Material: Drop-forged carbon steel heat treated Standard Finish: Galvanized to ASTM A- specification Design Factor: to Hook Packed Each Box of 0 Working Dimensions Weight/ Size A Cat. UPC No. Cat. UPC No. Load Limit B D L O R 00 in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm in. mm in. mm lb kg 6 40 046 404 622 0 40 4 2 6 62 4 6 0 2 2 4 8 28 2 6 4 40 04202 -- -- 000 44 8 2 2 2 /2 28 2 4 2 02 4 20 Standard Material: Drop-forged carbon steel Standard Finish: Blue Paint Finish Design Factor: to Other Features: Proof tested and certified Cargo Hooks, 48-S, (Portland Pattern) Working Dimensions Weight Cat. UPC No. Load Limit B D E L R Each Size No. 02048 ton kg in. mm in. mm in. mm in. mm in. mm lb kg 2 TF82 6 0 02 2 8 4 44 2 8 2 8 8 2 4. These items are made to order. Sorting Hooks, 4-S Standard Material: Drop-forged alloy steel heat treated Standard Finish: Painted orange Design Factor: to Working Load Limit Dimensions Weight/ Cat. UPC No. Tip Bottom B L R O 00 No. 02048 ton kg ton kg in. mm in. mm in. mm in. mm lb kg 800 002 2 84 2 6804 8 4 248 8 6 2 6 600 22
LATCH KITS Latch Kits For Hooks 6-G Campbell Latch Kit 6-U Universal Latch Kit READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING HOOK AND LATCH. 6-G LATCH KIT FOR CAMPBELL HOOK IMPORTANT: Instructions For Use 6-U UNIVERSAL LATCH KIT FOR ALL MAJOR HOOK BRANDS. Always inspect the hook and latch before using. 2. Always make sure the spring forces the latch against the point of the hook.. Check the load before lifting to make sure the hook (not the latch) is supporting the load. 4. To assemble latches on hooks, follow instructions supplied with latch kit. Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Loads may disengage from hook if proper procedures are not followed. A falling load may cause serious injury or death. The load must never be supported by the latch. Latches must always be inspected for wear or damage before use. If worn, distorted or damaged, discard and replace. Always stand clear of loads being lifted. Campbell offers latches already assembled to the hook as well as kits for field installation. Universal kits fit Campbell as well as competitive hooks, including Crosby and Midland, that are drilled for latches Spring spacer adapts latch to hooks with narrow cam Bolt and nut permit fast, easy installation 6-G kit Universal kit Dimensions Weight/ Size Size Cat. UPC No. Cat. UPC No. A B C D E F R 00 in. mm No. No. 02048 No. 02048 in. mm in. mm in. mm in. mm in. mm in. mm in. mm lb kg 2-22 00 022 40 088 2 2 8 6 4 4 2 8 6 2 4. 6 8-2 020 024 402 0 2 2 8 6 4 8 64 6 2 4. 2 -- -- 4-24 00 024 40 0 6 24 2 2 20 2 4 6 24 2 2 6 2 8 0-2 040 028 404 8 6 24 2 2 20 6 4 6 24 2 2 6.6 -- -- 6-26 00 026 -- -- 6 24 2 2 20 2 0 6 24 2 2 6 6.2 -- -- -2 060 022 40 2 6 24 2 2 20 8 48 6 24 2 2 6 6. 6 8-28 00 028 -- -- 2 2 2 2 8 60 2 2 8 0 6 4 64 2 2-2 080 026 406 2 2 2 2 2 6 68 2 2 8 0 6 4 64 6. -- -- 0-0 00 02802 -- -- 2 2 2 2 2 2 2 8 0 6 4 64 8.2 8 8 6-00 028 40 4 2 2 2 2 82 2 2 8 0 6 4 64 6 6 -- -- 2-2 0 02826 408 6 2 2 6 8 8 4 6 4 2 2 8 8 0 2 24 -- -- 4 -- -- 40 6 2 6 6 4 4 4 2 0 4 4 6 4 6 8 2 0 0. 2
SWIVELS Swivels 22-G Eye & Eye 2-G Jaw & Eye READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING SWIVELS. IMPORTANT: Instructions For Use. These swivels are designed for a straight line pull only. 2. These swivels are not designed to swivel under load.. Do not exceed working load limit (WLL). See table below. Working Load Limits - Swivels Size Carbon WLL in. mm lb kg 80 86 6 8 20 68 8 0 220 022 2 600 64 Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Use swivels only as indicated. Swivels must always be inspected for wear, distortion and damage before use. If worn, distorted or damaged, discard and replace. Always stand clear of loads being lifted. Do not angle load. 8 6 200 26 4 200 26 8 22 0,000 440 2 2,00 6 4 2 8,000 82 Campbell carbon swivels are all drop-forged and normalized. They meet the design requirements of Federal Specification RR-C-2. Galvanizing is to ASTM A specification.
SWIVELS 22-G, Eye & Eye Swivels Drop-Forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Galvanized to ASTM A- specification Design Factor: to Other Features: Meets Federal Specification RR-C-2 Type VII, Class 2 Working Dimensions Weight/ Size Cat. UPC No. Load Limit A B C D L R 00 in. mm No. 02048 lb kg in. mm in. mm in. mm in. mm in. mm in. mm lb kg 604 060 80 86 4 2 4 4 6 2 8 86 2 8..0 6 8 60 068 20 6 8 4 4 2 4 2 4 8 0 8 2 28. 2. 8 0 606 062 220 02 2 2 4 2 2 8 2 4 4 08 26.8 2 608 062 600 6 2 2 64 4 2 2 8 6 4 6 4 4 46 24 6. 8 6 60 064 200 2 6 8 4 4 44 2 8 60 8 20 6 4 28 08. 4 62 066 200 266 2 8 4 44 2 2 2 64 8 4 222 4 84 6 6. 8 22 64 066 0000 46 4 02 2 8 4 2 4 6 8 0 8 264 8 4 222 68 2. 2 66 060 200 60 4 2 4 2 4 2 2 64 2 8 4 28 4 248 8 404. 4 2 620 068 8000 86 8 4 4 8 8 8 8 6 4 2 22 62 8.
SWIVELS & CLEVIS LINK 2-G, Jaw & Eye Swivels Drop-Forged Carbon Steel - Galvanized Standard Material: Drop-forged carbon steel Standard Finish: Galvanized to ASTM A- specification Design Factor: to Other Features: Meets Federal Specification RR-C-2 Type VII, Class Working Dimensions Weight/ Size Cat. UPC No. Load Limit A B C K L N P R 00 in. mm No. 02048 lb kg in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm lb kg 6404 064 80 86 4 2 4 4 2 2 80 4 2 6 62 2 0 6 8 640 00006 20 6 8 4 4 2 2 4 6 2 6 8 2 8 2 8 0 6406 000 220 02 2 2 4 2 2 6408 00020 600 6 2 2 64 4 2 2 8 8 6 640 000 200 2 6 8 4 4 44 6 4 8 6 2 4 6 8 6 8 6 24 8 8 2 8 8 0 2 8 2 2 4 6 22 8 6 2 40 228 04 4 642 00044 200 266 2 8 4 44 2 8 2 8 20 4 44 8 22 644 000 0000 46 4 02 2 8 4 2 4 6 0 8 28 2 6 2 4 8 4 4 8 22 8 64 26 2 646 00068 200 60 4 2 4 2 4 2 2 64 4 44 6 2 2 6 62 8 2 8 8 2 424 4 2 6420 000 8000 86 8 4 4 8 8 2 6 2 2 0 2 6 8 8 6 24 6 0 Twin Clevis Link, 48-G Drop-forged Carbon Steel, Heat Treated Standard Material: Drop-forged carbon steel heat treated Standard Finish: Clevis and bolts are galvanized to ASTM A- specification cotter keys are stainless steel Design Factor: to Working Dimensions Pieces Weight/ Size Cat. UPC No. Load Limit A B C D Per Box in. mm in. mm No. 02048 lb kg in. mm in. mm in. mm in. mm Box lb kg 4 6 8 6400 8 00 6 6 6 2 2 2 64 8 0 0.6 2 8 0 - - 640 8 400 244 2 6 2 2 2 2 6 0 6.0 6 2 6402 2 200 4 8 6 8 4 8 2 6 4.
THIMBLES Thimbles -G Regular Wire Rope Stainless Regular Wire Rope 6-G Heavy Wire Rope Stainless Heavy Wire Rope 8-G Manila Rope READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING THIMBLES. Campbell thimbles are all made of hot rolled, mild steel. They are all galvanized to ASTM A- Specification. Campbell stainless regular thimbles are made of type 04 stainless steel, while the stainless heavy thimbles are made of type 6 stainless. REGULAR WIRE ROPE THIMBLE HEAVY WIRE ROPE THIMBLE MANILA ROPE THIMBLE IMPORTANT: Instructions For Use. A thimble is a wear pad that protects the rope from cuts and kinking. Always use an appropriate thimble when making an eye in a rope. Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Thimbles must always be inspected for cracks and wear before use. If worn, distorted or damaged, discard and replace. Use thimbles only as indicated. The thimble size must exactly correspond to the diameter of the rope being used. Never use a smaller thimble, because it will pinch the rope and cause broken and/or displaced wires. 2. When it is necessary to open a thimble to insert a fitting, make sure the points are properly aligned when the thimble is closed. Inspect carefully for cracks.. Thimbles are not designed for load carrying purposes; therefore working load limits have not been established.
THIMBLES Manila Rope Thimbles, 8-G Hot Rolled, Mild Steel Standard Material: Hot rolled, mild steel Standard Finish: Galvanized to ASTM A- specification Other Features: Meets design requirements of Federal Specifications FF-T-26B, Type For Rope Dimensions Weight/ Dia. Cat. UPC No. Max. Pin Dia. A B C 00 in. mm No. 02048 in. mm in. mm in. mm in. mm lb kg 8 0 62600 082 6 2 2 2 2 626002 084 6 4 6 2 2 8 8 4 8 6 62600 084 6 2 8 22 2 8 4 4 626004 088 6 2 8 2 6 46 2 2 6 8 22 62600 086 8 2 6 0 2 2 26 2 0 2 626006 082 6 0 4 2 2 4 6 0 2 8 2 62600 088 6 8 2 8 60 2 Standard Material: Hot rolled, mild steel Galvanized Regular Wire Rope Thimbles, -G Hot Rolled, Mild Steel For Rope Dimensions Weight/ Dia. Cat. UPC No. B C D F L P (pin) W 00 in. mm - in. mm No. 02048 in. mm in. mm in. mm in. mm in. mm in. mm in. mm lb kg 8 - - 62600 068 2 6 2 4 64 4 44 6 8 2 6 - - 626002 0 2 6 2 6 64 4 44 6 8 2 - - 62600 082 2 4 6 6 8 64 8 48 6 8 2 2 6 8 - - 626004 0 2 6 2 2 64 2 8 4 6 2 4 2 2 8 0 - - 62600 060 2 2 42 6 24 6 6 2 2 4 6 24 2 8 0 6 - - 626006 062 6 4 8 2 2 - - 62600 062 6 4 2 2 2 2 6 4 6 2 2 4 0 8 2 4 44 6 2 2 8 6 8 2 6 46 6 4 8 6 626008 066 2 8 6 2 8 8 6 8 4 6 2 6 2 4 - - 62600 064 2 8 8 4 8 22 - - 62600 060 6 8 4 44 2 2 20 2 2 2 64 4 4 6 06 6 40 2 2 64 40 8 64 4 4 2 4 8 4 2 2 2 6 4 2 2 - - 6260 066 4 6 0 2 8 60 6 2 8 2 - - 62602 064 4 8 2 8 6 6 0 4 2 - - 6260 068 4 2 4 2 4 0 6 2 8 - - 62604 068 6 4 8 8 4 64 4 4 46 2 4 2 8 0 48 6 6 2 6 2 2 64 4 0240 64 6 6 4 2 8 6 4 8 0 6 6 8 200 8 8 0 24
THIMBLES Regular Wire Rope Thimbles, Type 04 Stainless Steel Standard Material: Forged Type 04 Stainless Steel Standard Finish: Electro-polish For Rope Overall Weight/ Dia. Cat. UPC No. Thickness Length Inside Width 00 in. mm No. 02048 in. mm in. mm in. mm lb kg 8 64002 0 6 6400 082 64004 0 6 8 6400 040 8 64006 042 2 4 44 2 4 44 8 0 8 48 6 2 2 6 4 2 4 2 2 8 2 2 8 2 2 8 2 2 2 2 2 2 2 8 4 2 2 64008 042 2 2 2 2 64 2 2 4 6 Heavy Wire Rope Thimbles, 6-G Hot Rolled, Mild Steel Standard Material: Hot rolled, mild steel Galvanized For Rope Dimensions Weight/ Dia. Cat. UPC No. B C D F L P (pin) W 00 in. mm - in. mm No. 02048 in. mm in. mm in. mm in. mm in. mm in. mm in. mm lb kg - - 626020 0 8 4 8 22 2 6 2 2 8 4 6 2 2 8 6 8 - - 6260202 028 8 48 6 2 8 0 64 2 2 2 64 6 24 6 46 2 8 0 - - 626020 0 2 8 4 8 2 6 - - 6260204 042 2 4 4 2 6 2 64 6 6 2 2 8 4 2 0 8 6 8 6 0 2 8 60 2 2 2 6 4 626020 0 2 4 0 2 8 8 6 64 4 8 2 6 2 6 68 4 22 8 6 - - 6260206 066 4 8 4 44 4 - - 626020 0 4 2 8 22 - - 6260208 080 4 4 08 2 4 6 6 2 6 24 2 4 4 4 08 8 4 8 2 2 6 2 8 48 6 4 64 2 6 2 40 2 8 4 4 4 08 8 84 2 - - 626020 0 4 2 4 2 2 64 6 2 8 2 4 2 626020 080 8 0 2 8 6 8 2 8 62602 080 6 4 2 8 6 40 6 8 6 2 8 60 4 6 2 00 6 8 2 4 0 8 4 68 6 2 22 8 86 8 8 24
THIMBLES Heavy Wire Rope Thimbles, Type 6 Stainless Steel Standard Material: Type 6 Stainless Steel Standard Finish: Electro-polish For Rope Overall Weight/ Dia. Cat. UPC No. Thickness Length Inside Width 00 in. mm No. 02048 in. mm in. mm in. mm lb kg 640604 046 2 0 2 6 6 8 22. 6 8 64060 044 8 640606 040 2 2 640608 046 2 2 2 64 6 2 4 6 2 2 2 8 8 2 2 2 2 2 8 2 2 8 2 8 64060 044 2 4 4 08 4 44 4 4 64062 048 4 2 2 2 4 6 Note: Thimbles are not designed for load carrying purposes; therefore, working load limits have not been established. Slip-Thru Thimbles, 4-S Hot Rolled, Mild Steel Standard Material: Hot rolled, mild steel Standard Finish: Painted blue For Rope Weight/ Size Diameter Cat. UPC No. 00 No. in. mm in. mm No. 02048 lb kg 2 6 8 8 0 62640 026 0 2 4 4-Spec 6 8 6 8 6 2-6 -4 626402 026 2 4 62640 028 2 0 4 626404 020 2 4 Dimensions B C D F L P (max pin dia.) R W Style in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm 2 8 8 4 44 2 64 8 0 6 4 4 4 8 4 8 24 2 4 4 8 4 2 6 6 4-Spec 8 4 8 2 6 6 2 6 2 2 4 6 2 6 2 6 6 2 4 2 4 /64 4 8 6 208 2 2 64 6 0 8 0 6 6 22 6 0 6 0 6 8 62
LINKS 82-S, G, A Weldless Sling Links READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING THESE LINKS. SLING LINK Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Use links only as indicated. Links must always be inspected for wear and distortion before use. If worn, distorted or damaged, discard and replace. Do not weld on these links. Always stand clear of loads being lifted. Campbell links are all drop-forged and heat treated. Galvanizing is to ASTM A- specification. IMPORTANT: Instructions For Use. Make sure the link has a working load limit compatible with that of the chain or wire rope with which it is used. 2. Do not exceed WLL See table below.. The WLL can be significantly reduced under the following conditions: Wear and/or Distortion Extreme Heat Weld Spatter If link is exposed to any of these conditions, discard it. Working Load Limits (lb and kg) - Links Sling Link Carbon Alloy Size WLL WLL in. mm lb kg lb kg 8 0 600 26 2600 80 2 200 4000 86 8 6 4200 0 800 26 4 6000 224 8200 2 8 22 800 68 -- -- 2 0800 40 -- -- 82-S, 82-G, 82-A Weldless Sling Links Standard Material: Drop-forged steel, heat treated Design Factor: 6 to Carbon Steel, Heat Treated Blue Painted Galvanized Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Load Limit A B C Each in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm lb kg 8 0 62 060 62 060 600 26 2 4 2 8 4..4 2 622 062 622 064 200 6 2 2.6.2 8 6 62 064 62 068 4200 0 4 2 2 64 4 2..0 4 624 066 624 062 6000 222 4 2 4 6 2 8..86 8 22 62 068 62 066 800 6 4 2 8 4 44 2..2 2 626 06802 626 068 0800 48 6 2 4 02 2 4.4 2.00
LINKS 82-S, 82-G, 82-A Weldless Sling Links, continued Standard Material: Drop-forged steel, heat treated Design Factor: 6 to Alloy, Orange Painted Blue Painted Galvanized Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Load Limit A B C Each in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm lb kg 8 0 626 06826 62 060 600 26 2 4 2 8 4..4 2 6262 068 622 064 200 6 2 2.6.2 8 6 626 06840 62 068 4200 0 4 2 2 64 4 2..0 4 6264 068 624 062 6000 222 4 2 4 6 2 8..86
EYEBOLTS Eyebolts, 46-G Regular Nut, 444-G Shoulder Nut READ AND UNDERSTAND THESE S AND INSTRUCTIONS AND FOLLOW ALL EYEBOLT SAFETY INFORMATION PRESENTED HERE BEFORE USING EYEBOLT ASSEMBLIES. Campbell carbon steel eyebolts are all drop-forged and normalized. Galvanizing is to ASTM A- specification. IMPORTANT: Instructions For Use. Make sure the eyebolt is properly seated by screwing it down completely and tightening the nut securely against the load. 2. An eyebolt must be installed into a tapped hole with a minimum depth of two times the shank diameter.. Make sure the threads on the shank and in the hole are clean and undamaged. 4. Loads must always be applied parallel to the plane of the eye and never across the plane of the eye. Effect of Angular Loading on WLL of Carbon Steel, Shoulder Nut Eyebolts Vertical Shank Pull Pull 60 Pull 4 Pull Less than Diameter WLL WLL WLL WLL 4 Pull in. mm lb kg lb kg lb kg lb kg 00 22 00 6 0 86 6 6 8 80 86 46 2 2 4 20 8 0 20 68 68 4 0 4 Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Loads may slip or fail if proper eyebolt assembly and lifting procedures are not used. A falling load can seriously injure or kill. Eyebolts must always be inspected for wear and distortion before use. If worn, distorted or damaged, discard and replace. Do not use regular nut eyebolts for angular lifting. Never machine, cut or grind and eyebolt. Always stand clear of loads being lifted.. Always lift the load with a steady, even pull. Do not shock load. 6. Do not exceed working load limit (WLL). See table below. The standard WLL s are established for a vertical pull. When the load is pulled at an angle, the WLL is reduced as shown in the table below.. When using lifting slings having two or more legs, make sure the load on each leg is calculated based on the angular loading. The shoulder nut eyebolt with the correct WLL under those conditions must be used. 8. Use only the heavy hex nuts supplied with the eyebolts. Effect of Angular Loading on WLL of Stainless Steel, Shoulder Nut Eyebolts Vertical Shank Pull Pull 60 Pull 4 Pull Less than Diameter WLL WLL WLL WLL 4 Pull in. mm lb kg lb kg lb kg lb kg 00 22 00 6 0 86 6 6 8 80 4 42 20 2 8 8 0 60 2 6 288 40 84 20 2 2 220 68 2 6 8 6 60 24 8 6 600 64 80 8 260 2 00 40 NOT RECOM- MENDED 2 20 6 80 6 0 4 24 8 6 440 62 80 88 200 4 860 0 NOT RECOM- MENDED 4 200 26 2860 28 820 826 00 0 4 40 24 282 28 8 28 8 8 22 200 26 60 8 220 44 800 8 8 22 0 2 20 80 24 80 808 2 0000 440 00 24 00 8 200 2 0 424 0 28 2 48 240 062
EYEBOLTS 46-G, 444G Nut Eyebolts, Galvanized Standard Material: Drop-forged carbon steel Working load limits apply only to eyebolts in lifting or pulling applications Galvanizing to ASTM A- specification Note: If angular loading is necessary, eyebolts are to be used at reduced loads (see illustration) 46-G Regular Nut 444-G Shoulder Nut Shank Dimensions Regular Shoulder Working Dimensions Weight/ Dia. Length Cat. UPC No. Cat. UPC No. Load Limit A B T 00 in. mm in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm lb kg 2 00 004 020 004 0 24 2 2 2 8 8 8 4 4 02 002 004 0202 002 0 24 6 8 2 4 00 008 020 006 80 86 6 8 4 4 08 004 006 0204 006 80 86 8 0 2 2 64 00 002 020 008 20 6 8 0 4 2 4 006 008 0206 000 20 6 8 0 6 2 00 006 -- -- 20 6 2 2 2 2 64 2 8 6 /4 2 2 8 8 8 6 /4 2 2 2 64 6 4 8 4 2 8 2 8 2 2 4 2 8 2 2 64 2 2 2 4 2 8 6 2 2 4 8 008 00802 0208 006 220 02 2 2 2 8 4 2 2 6 2 00 008 020 0 220 02 2 2 6 68 4 2 8 20 00 00826 -- -- 220 02 2 2 6 8 2 0 24 0 008 -- -- 220 02 2 2 6 88 40 2 2 0 02 00840 -- -- 220 02 2 2 4 02 00 4 8 6 4 02 0 008 02 0 600 6 4 2 2 2 64 2 04 4 8 6 6 2 04 00864 024 044 600 6 4 2 2 2 64 6 20 4 8 6 8 20 0 008 -- -- 600 6 4 2 2 2 64 6 8 6 0 24 06 00888 -- -- 600 6 4 2 2 2 64 6 2 6 8 6 2 0 0 008 -- -- 600 6 4 2 2 2 64 4 02 68 6 4 4 2 4 08 000 028 068 200 2 2 8 6 2 6 4 6 2 0 008 02 0 200 2 2 8 6 6 0 86 4 8 20 020 002 -- -- 200 2 2 8 6 6 208 4 4 0 24 02 002 -- -- 200 2 2 8 6 6 20 04 4 2 0 022 004 -- -- 200 2 2 8 6 4 02 2 6 4 8 02 006 -- -- 200 2 2 8 6 2 20 2 8 22 2 -- -- 0224 082 200 266 4 44 2 8 2 2 64 22 4 8 22 8 20 -- -- 022 0 200 266 4 44 2 8 4 02 20 2 8 22 2 0 -- -- -- -- 200 266 4 44 2 8 4 02 40 4 8 22 8 4 -- -- -- -- 200 266 4 44 2 8 8 440 200 2 6 2 028 000 0228 020 0000 46 2 4 02 6 0 2 22 02 004 022 022 0000 46 2 4 02 4 02 40 2 2 2 0 00 002 -- - 0000 46 2 4 02 4 02 20 26 2 8 4 0 008 -- -- 0000 46 2 4 02 8 60 2 4 2 8 20 -- -- 02 8 000 680 2 2 64 2 4 02 0 4 4 2 2 0 -- -- 020 820 000 680 2 2 64 2 4 02 00 40 These items are made to order.
EYEBOLTS Nut Eyebolts, Drop-Forged, Type 6 Stainless Steel Shank Length O.D. I.D. Regular and shoulder eyebolts Non-magnetic All have UNC-2, right hand thread Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish M-28-ST Regular Nut M-2-ST Shoulder Nut Shank Diameter Shank Dimensions Dimensions Regular Shoulder Working Regular Shoulder Thread Weight/ Dia. Length Cat. UPC No. Cat. UPC No. Load Limit I.D. O.D. I.D. O.D. Length 00 in. mm in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm in. mm in. mm lb kg 2 6400 042 -- -- 00 22 2 2 2 8 22 2 8 8 8 4 4 02 64002 042 640002 04606 00 22 6 8 2 4 -- -- 64000 046 80 4 6 8 4 4 08 64004 044 640004 04620 80 4 8 2 2 64 6400 040 64000 046,60 26 8 4 2 4 64006 046 640006 04644,60 26 2 2 2 8 22 2 2 64 2 8 6 8 2 8 6 8 2 2 8 6 8 6 8 2 8 6 8 2 2 2 64 8 4 2 8 4 8 2 8 24 4 2 8 4 8 2 2 64 0 4 2 4 8 6400 044 64000 046 2,0 2 2 2 4 44 2 8 4 2 2 6 2 64008 048 640008 04668 2,0 2 2 2 4 44 6 8 6 4 02 6400 048 64000 046,440,60 4 2 2 2 64 4 2 2 4 2 04 4 4 4 2 4 640 04804 6400 04682,40 2,2 2 8 2 8 2 8 2 4 0 2 6 8 22 2 640 048 6400 046,0,24 4 44 8 86 4 44 4 8 2 2 64 260 8 2 6 2 640 04828 6400 040,0 4,20 2 4 02 2 4 0 20-S, Pad Eyes, Carbon Steel Uses: Widely used on farm machinery, trucks, steel hulled marine vessels and material handling equipment Standard Material: Drop-forged C-08 carbon steel Standard Finish: Self-colored Dimensions Weight/ Size Cat. UPC No. A B C D E F G 00 in. mm No. 02048 in. mm in. mm in. mm in. mm in. mm in. mm in. mm lb kg 2 8 00 006 2 002 000 4 02 00 000 2 004 002 2 4 8 2 6 2 8 8 6 2 4 6 2 4 6 8 22 8 4 2 8 4 2 6 4 2 2 6 6 24 2 8 6 4 2 /4 44 6 40 2 8 8 4 8 0 8 6 4 0 2 6 42
LIFTING EYE & EYE NUTS Lifting Eyes & Eye Nuts READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING LIFTING EYES AND NUTS. Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Loads may slip or fail if proper assembly and lifting procedures are not used. Use lifting eyes and eye nuts only as indicated. Lifting eyes and eye nuts must always be inspected for wear, distortion and damage before use. If worn, distorted or damaged, discard and replace. Always stand clear of loads being lifted. WLL (Lb and kg) of Carbon Eye Nuts Eye Nut Vertical 60 4 Tap Pull Pull Pull Pull Less Size Size WLL WLL WLL WLL Than 4 No. in. mm lb kg lb kg lb kg lb kg Pull, A 6 8 80 86 46 2 2 4 20 2 8 0 20 6 68 4 0 4 6 60 48 0 4 26 40 86, A 2 220 02 2 6 8 6 60 24 6 8 22 200 266 60 8 220 44 800 8 8 4 2 200 68 860 20 24 800 2 0 2 8 2400 0 0 44 40 400 0 242 NOT RECOM- MENDED STAINLESS LIFTING EYE EYE NUT Campbell carbon eye nuts are all drop-forged and normalized. Galvanizing is to ASTM A- specification. IMPORTANT: Instructions For Use. Do not exceed working load limit (WLL) as shown in the table below. The standard WLL's are established for a vertical pull. The WLL is significantly reduced when angular loading is involved as shown in the table below. 2. When using lifting slings having two or more legs, make sure the load on each leg is calculated based on the angular loading. The eye nut with the correct WLL under those conditions must be used.. Make sure the eye nuts are properly seated by screwing them down completely. 4. Make sure the threads in the hole are clean and undamaged.. Loads must always be applied parallel to the plane of the eye and never across the plane. 6. Always stand clear of the load and lift the load with a steady, even pull. Do not shock load. WLL (Lb and kg) of Stainless Steel Lifting Eyes Eye Nut Vertical 60 4 Tap Pull Pull Pull Pull Less Size Size WLL WLL WLL WLL Than 4 No. in. mm lb kg lb kg lb kg lb kg Pull 2 20 6 80 6 0 4 24 6 8 6 440 62 80 88 200 4 860 0 NOT RECOM- 4 40 24 282 28 8 28 8 MENDED 2 0 424 0 28 2 48 240 062
PAD EYES & EYE NUTS Lifting Eyes, M-4-ST Drop-forged Type 6 Stainless Steel Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish Working Weight Size Cat. UPC No. Load Limit Each No. No. 02048 lb kg lb kg 64004 020 20.2. 6 6400 0 440 60.66.0 64006 044 40 22.86. 6400 0 0 420.82.8 Dimensions Size D L A C B T No. in. mm in. mm in. mm in. mm in. mm in. mm 2 4 2 0 2 2 8 6 6 8 6 2 2 2 64 4 2 8 6 4 4 2 2 6 2 8 2 2 8 22 2 6 6 0 6 46 8 22 6 2 Eye Nuts, 6-G Drop-forged Carbon Steel, Normalized Standard Material: Drop-forged carbon steel normalized Standard Finish: Galvanized to ASTM A- specification Design Factor: to Working Tap Size M Weight/ Size Cat. UPC No. Load Limit UNC-2B 00 No. No. 02048 lb kg in. mm lb kg A 0002 004 80 86 2 000 00420 20 6 0004 004 60 48 A 000 00444 220 02 6 0008 004 200 266 6 8 8 4 8 0 6 6 2 2 2 8 22 6 8 00 000 200 68 4 2 6 6 0 002 002 2400 0 2 8 66 28 Size A C D E F G S T No. in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm A 4 2 4 6 2 2 2 2 2 2 42 2 8 4 2 64 2 4 6 4 2 2 6 8 2 64 2 2 4 2 2 8 2 6 2 2 8 0 2 2 6 A 2 4 2 2 8 2 6 2 2 8 0 2 2 6 6 2 8 2 2 6 6 8 4 8 2 4 4 6 0 8 4 2 4 2 2 64 2 8 2 8 4 6 46 6 2 6 48 0 8 4 8 4 6 0 2 2 64 2 4 2 8 4 2 6 6
TURNBUCKLES 8-G Hook & Eye -S Stub End -G Hook & Hook M-2-ST Stainless Eye & Eye 80-G Eye & Eye M--ST Stainless Jaw & Eye 86-G Jaw & Eye M-6-ST Stainless Jaw & Jaw Turnbuckles 88-G Jaw & Jaw READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING TURNBUCKLES. IMPORTANT: Instructions For Use. Turnbuckles are designed for a static load and are typically used with guy wires. 2. Do not exceed working load limit (WLL). See table below. Working Load Limits (lb and kg) Turnbuckles Carbon Stainless Carbon Eye & Eye Eye & Eye Hook & Turnbuckle Jaw & Eye Jaw & Eye Hook Size Jaw & Jaw Jaw & Jaw Hook & Eye Inches lb kg lb kg lb kg 4 x 4 00 22 00 22 400 82 6 x 4 2 800 6 800 6 00 8 HOOK & EYE HOOK & HOOK EYE & EYE JAW & EYE 8 x 6 200 4 200 4 000 44 2 x 6,, 2 2200 2200 00 68 8 x 6,, 2, 8 00 8 00 8 200,044 JAW & JAW 4 x 6,, 2, 8, 24 200 26 200 26 000,62 8 x 2, 8 200 26 * * 600,64 x 6, 2, 8, 24 0000 440 0000 440 4200,0 4 x 2, 8, 24 200 60 * * 000 2,20 *Item not manufactured. Stub End Turnbuckles are not rated. The rating is only as good as the weld or connection method. LOCK NUT 4. In loads where there is vibration, lock nuts (jam nuts) should be used to prevent the connection from turning or loosening. Lock nuts are available for all turnbuckles and may be ordered separately or assembled on the turnbuckle.. The jaw ends come with different hardware depending on their size. Jaws from /4" through /8" have a hex head bolt and nut. Jaws from /4" through /2" have cotter key and bolt. STUB END Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Use turnbuckles only as indicated. Turnbuckles must always be inspected for wear, distortion, cracks and damage before use. If worn, distorted or damaged, discard and replace. Turnbuckles are not designed for angular loading, so the loading must be applied in a straight line. Campbell carbon turnbuckles are all drop-forged and meet the design requirements of Federal Specification ASTM F-4, Type, Grade. All types, except stubend, are galvanized to ASTM A specifications. Campbell stainless turnbuckles are all drop-forged, made of type 6 stainless steel, and have an electropolished finish. DO NOT EXCEED the working load limit. DO NOT shock or impact load.
TURNBUCKLES Hook & Eye Turnbuckles, 8-G Drop-forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Galvanized to ASTM A- specification Design Factor: to Other Features: Meets design requirements of ASTM F4, Type, Grade, Class F Working Dimensions Weight/ Cat. UPC No. Load Limit A (Thread Dia.) B (Take Up) W (Length) 00 No. 02048 lb kg in. mm in. mm in. mm lb kg 6200 08664 400 8 62002 086 00 8 6200 08688 000 44 6200 086 00 680 62006 08660 00 680 6200 08668 00 680 6200 08662 200 04 6200 08662 200 04 620 08664 200 04 6202 08666 200 04 620 08666 000 6 6204 08660 000 6 620 08668 000 6 6206 08664 000 6 620 086 600 6 62020 08624 600 6 4 02 6 8 2 6 8 4 2 4 8 28 4 2 8 0 6 2 8 2 8 2 6 2 8 60 2 22 6 8 40 226 0 2 2 0 8 486 24 8 6 6 2 4 6 0 264 20 8 6 22 6 446 4 8 6 2 0 20 6 22 68 8 6 8 4 26 6 684 480 28 4 6 2 6 8 46 82 4 22 8 42 46 22 4 2 0 22 8 68 000 6 4 8 4 28 8 2 000 6 8 22 2 0 2 6 608 600 6 8 22 8 4 2 6 60 600 6 62022 08648 4200 0 2 2 0 2 6 66 4200 0 6202 086 4200 0 2 8 4 6 808 4200 0 62024 08662 4200 0 2 24 60 6 60 4200 0
TURNBUCKLES Eye & Eye Turnbuckles, 80-G Drop-forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Galvanized to ASTM A- specification Design Factor: to Other Features: Meets design requirements of ASTM F4, Type, Grade, Class D Dimensions Working (Dia.) (Take Up) (Length) Weight/ Cat. UPC No. Load Limit A B W E G H J 00 lb No. 02048 lb kg in. mm in. mm in. mm in. mm in. mm in. mm in. mm lb kg 6200 08042 00 22 4 02 8 200 6 40 8 0 2 6 2 2 20 2 2 62002 080 800 6 6 8 4 2 4 6 240 2 2 2 2 6 24 4 20 6200 08066 200 44 8 0 6 2 6 00 2 2 60 6 4 2 8 2 84 8 6200 080 2200 8 2 6 2 6 4 2 2 4 6 6 6 62006 08080 2200 8 2 22 6 6 48 2 2 4 6 6 8 0 6200 080 2200 8 2 2 0 6 44 2 2 4 6 6 246 2 6200 080 00 88 8 6 6 2 4 8 8 2 8 2 2 2 2 4 44 26 6 6200 080 00 88 8 6 22 8 44 2 8 2 2 2 2 4 44 0 4 620 082 00 88 8 6 2 0 20 8 0 2 8 2 2 2 2 4 44 0 6202 084 00 88 8 6 8 4 26 8 68 2 8 2 2 2 2 4 44 480 28 620 084 200 2 6204 088 200 2 620 086 200 2 6206 082 200 2 620 088 200 2 620 086 200 266 62020 08202 200 266 4 6 2 6 4 42 4 4 08 2 26 4 22 4 02 4 4 08 2 26 4 2 0 22 4 8 4 4 08 2 26 4 8 4 28 4 0 4 4 08 2 26 4 24 60 4 4 88 4 4 08 2 26 8 22 2 0 24 8 6 4 4 2 2 8 22 8 4 0 8 6 4 4 2 2 8 6 2 8 4 80 8 6 2 8 4 48 208 8 6 2 8 4 4 26 8 6 2 8 4 00 8 8 6 2 8 4 860 0 4 2 8 60 4 2 8 60 00 4 6202 082 0000 46 2 6 2 20 2 2 4 46 2 62022 08226 0000 46 2 2 0 26 2 6 4 46 2 6202 082 0000 46 2 8 4 2 2 826 4 46 2 62024 08240 0000 46 2 24 60 8 2 8 4 46 2 8 22 6 800 6 8 22 6 0 8 22 6 400 66 8 22 6 600 26 6202 082 200 68 4 2 2 0 2 8 46 8 2 2 4 8 2 6 0 200 62028 08264 200 68 4 2 8 4 8 8 8 2 2 4 8 2 6 0 200 6202 082 200 68 4 2 24 60 4 8 0 8 2 2 4 8 2 6 0 2800 2 6202 08288 2400 0 2 8 2 0 4 8 22 2 8 4 4 2 4 8 0 22 28 6204 686 2400 0 2 8 24 60 4 2 22 2 8 4 4 2 4 2 4 800 2
Eye & Eye Turnbuckles, M-2-ST Drop-forged Type6 Stainless Steel TURNBUCKLES C D Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish A B Dimensions Inside Eye Working Load Cat. UPC No. Size (A) Take-up (B) Length (C) Diameter (D) Weight Each Limit No. 02048 in. mm in. mm in. mm in. mm lb kg lb kg 6400 0 64002 064 6400 0 64004 088 6400 0 6400 040 4 02 2 6 8 4 2 4 8 2 26 8 0 6 2 0 4 2 2 6 2 2 0 8 6 6 2 2 4 6 2 2 0.2 00 22 2 0.2 800 6 2 0.4 200 4 4 2 0. 2200 8 22 2 2. 00 8 4 6 2 2 4 2 4.8 200 26 640 042 2 6 2 48 8 4 0000 440
TURNBUCKLES Jaw & Jaw Turnbuckles, 88-G Drop-forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Galvanized to ASTM A- specification Design Factor: to Other Features: Meets design requirements of Federal Specification ASTM F4, Type, Grade, Class G Jaws on sizes /4 through /8 have hex head bolt and nut. Jaws on sizes /4 through -/2 have cotter key and bolt Working Dimensions Weight/ Cat. UPC No. Load Limit Thread Dia. Take Up Length 00 No. 02048 lb kg in. mm in. mm in. mm lb kg 6200 08646 00 22 62002 086 800 6 6200 08660 200 44 6200 086 2200 8 62006 08684 2200 8 6200 086 2200 8 6200 080 00 88 6200 084 00 88 620 082 00 88 6202 088 00 88 620 084 200 2 6204 082 200 2 620 086 200 2 6206 086 200 2 620 088 200 2 620 080 200 266 62020 08806 200 266 4 02 6 202 6 6 8 4 /2 4 6 2 2 8 0 6 2 6 284 4 4 2 6 2 2 4 24 0 2 22 4 400 2 8 2 2 0 8 4 46 26 20 8 6 6 2 4 4 28 2 8 6 22 4 4 4 8 8 6 2 0 20 4 2 400 82 8 6 8 4 26 40 204 4 6 2 4 400 44 20 4 22 8 4 46 8 2 4 2 0 2 4 2 6 28 4 8 4 2 4 0 60 4 4 24 60 4 8 86 8 22 2 0 2 8 4 8 80 8 22 8 4 2 8 46 208 48 6202 088 0000 46 2 6 2 6 44 4 40 62022 08820 0000 46 2 2 0 2 6 646 20 86 6202 088 0000 46 2 8 4 6 60 08 62024 08844 0000 46 2 24 60 6 8 80 6202 088 200 68 4 2 2 0 2 2 6 240 2 62028 08868 200 68 4 2 8 4 2 8 260 62 6202 088 200 68 4 2 24 60 2 00 00 40 6202 08882 2400 0 2 8 2 0 4 4 200 4 620 088 2400 0 2 8 8 4 4 46 00 680 6204 680 2400 0 2 8 24 60 4 4 0 400 86
TURNBUCKLES Jaw & Jaw Turnbuckles, 88-G Drop-forged Carbon Steel Dimensions Cat. D H K L M Q P No. in. mm in. mm in. mm in. mm in. mm in. mm in. mm 6200 2 40 8 6 2 0 6 2 2 62002 6 4 6 2 6 2 4 6200 2 2 2 8 22 2 6 4 6 8 6 2 6200 2 8 6 6 0 8 6 6 8 4 8 0 6 2 62006 2 8 6 6 0 8 6 6 8 4 8 0 6 2 6200 2 8 6 6 0 8 6 6 8 4 8 0 6 2 6200 8 86 8 4 6 6 24 2 8 6200 8 86 8 4 6 6 24 2 8 620 8 86 8 4 6 6 24 2 8 6202 8 86 8 4 6 6 24 2 8 620 4 6 46 6 24 2 2 6 0 8 6 2 8 6204 4 6 46 6 24 2 2 6 0 8 6 2 8 620 4 6 46 6 24 2 2 6 0 8 6 2 8 6206 4 6 46 6 24 2 2 6 0 8 6 2 8 620 4 6 46 6 24 2 2 6 0 8 6 2 8 620 4 8 2 8 2 62020 4 8 2 8 2 6202 2 2 6 6 6 0 62022 2 2 6 6 6 0 6202 2 2 6 6 6 0 62024 2 2 6 6 6 0 2 8 2 8 4 6 40 4 6 40 4 6 40 4 6 40 4 4 44 4 4 44 8 22 2 6 2 8 22 2 6 2 8 22 2 6 2 8 22 2 6 2 6202 6 6 4 2 8 4 44 62028 6 6 4 2 8 4 44 6202 6 6 4 2 8 4 44 8 22 2 8 2 2 6 62 8 22 2 8 2 2 6 62 8 22 2 8 2 2 6 62 6202 8 2 26 4 8 2 6 2 2 28 2 6 8 2 6 620 8 2 26 4 8 2 6 2 2 28 2 6 8 2 6 6204 8 2 26 4 8 2 6 2 2 28 2 6 8 2 6
TURNBUCKLES Jaw & Jaw Turnbuckles, M-6-ST Drop-forged Type6 Stainless Steel Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish D C E A B Dimensions Working Load Cat. UPC No. Size (A) Take Up (B) Length (C) Pin Dia. (D) Jaw Opening (E) Weight Each Limit No. 02048 in. mm in. mm in. mm in. mm in. mm lb kg lb kg 64020 042 640202 044 64020 046 640204 046 64020 040 64020 048 4 02 2 6 8 4 2 4 8 2 26 8 0 6 2 0 4 2 2 6 2 2 0 8 6 6 2 2 4 4 6 2 2 4 6402 044 2 6 2 48 6 6 8 8 2 6 2 6 4 2 0.2 00 22 2 0.2 800 6 4 0. 200 4 8 6 2 0. 2200 6 2. 00 8 8 6 2 2.2 200 26 4 4 2 0 2 4. 0000 440
TURNBUCKLES Hook and Hook Turnbuckles, -G Drop-forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Galvanized to ASTM A- specification Design Factor: to Other Features: Meets design requirements of Federal Specification ASTM F4, Type, Grade, Class E Dimensions Working (Dia.) (Take Up) (Length) Weight/ Cat. UPC No. Load Limit A B W D K L M 00 lb No. 02048 lb kg in. mm in. mm in. mm in. mm in. mm in. mm in. mm lb kg 62020 08680 400 8 4 02 4 8 48 6 8 0 2 620202 08686 00 8 6 8 4 /2 4 8 28 2 2 2 2 6 8 0 2 62020 08682 000 44 8 0 6 2 6 2 2 6 62 6 4 8 6 8 0 86 62020 08680 00 680 2 6 2 2 4 24 2 2 2 2 8 6 4 2 64 4 620206 08684 00 680 2 22 4 400 2 2 2 2 8 6 4 2 2 62020 08684 00 680 2 2 0 8 4 46 2 2 2 2 8 6 4 2 24 62020 08686 200 04 8 6 6 2 4 2 2 8 2 2 2 8 22 8 6 22 2 62020 08688 200 04 8 6 22 4 48 2 8 2 2 2 8 22 8 6 20 4 6202 08688 200 04 8 6 2 0 20 4 4 2 8 2 2 2 8 22 8 6 2 8 62022 08682 200 04 8 6 8 4 2 686 2 8 2 2 2 8 22 8 6 480 28 6202 08608 000 6 4 6 2 6 406 2 0 2 2 2 4 8 62024 086 000 6 4 22 48 2 0 2 2 2 4 46 26 6202 08622 000 6 4 2 0 22 2 0 2 2 2 4 22 62026 086 000 6 4 8 4 28 2 0 2 2 2 4 2 2 6202 086 600 6 620220 08660 600 6 8 22 2 0 2 0 2 2 8 4 2 6 0 8 22 8 4 2 2 2 8 4 2 6 0 8 22 0 22 8 22 60 46 620222 08684 4200 0 2 2 0 2 8 68 2 8 4 2 2 0 62022 080 000 2268 4 2 2 0 2 8 68 8 4 8 4 8 4 2 2000 08 These items are made to order.
TURNBUCKLES Jaw & Eye Turnbuckles, 86-G Drop-forged Carbon Steel See Figure 80-G for eye dimensions See Figure 88-G for jaw dimensions Drop-forged Carbon Steel Galvanized to ASTM A- specifications Design factor to Working Dimensions Weight/ Cat. UPC No. Load Limit Thread Dia. (A) Take Up (B) Length (W) 00 No. 02048 lb kg in. mm in. mm in. mm lb kg 62040 088 00 22 620402 084 800 6 62040 08400 200 44 62040 084 2200 8 620406 08424 2200 8 62040 084 2200 8 62040 08448 00 88 62040 084 00 88 6204 08462 00 88 6204 08486 200 2 62044 084 200 2 6204 080 200 2 62046 086 200 2 6204 080 200 266 620420 084 200 266 4 02 8 200 6 8 4 2 4 8 28 48 22 8 0 6 2 6 24 0 4 2 6 2 8 64 4 2 22 6 8 40 208 4 2 2 0 8 486 2 8 6 6 2 4 8 8 26 20 8 6 22 6 42 0 0 8 6 2 0 20 6 2 80 4 6 2 6 4 4 42 8 4 22 4 48 488 222 4 2 0 22 604 24 4 8 4 28 4 8 0 8 22 2 0 2 0 84 0 8 22 8 4 2 42 8 62042 084 0000 46 2 6 2 20 08 2 44 620422 086 0000 46 2 2 0 26 660 206 48 62042 088 0000 46 2 8 4 2 8 484 64 620424 088 0000 46 2 24 60 8 6 00 2 62042 082 200 68 4 2 2 0 28 6 2 80 8 620428 08608 200 68 4 2 8 4 4 6 88 2400,00 62042 08622 2400 0 2 8 2 0 0 8 84 00,8
TURNBUCKLES Jaw & Eye Turnbuckles, M--ST Drop-forged Type6 Stainless Steel D C E Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish A B Dimensions Inside Eye Working Load Cat. UPC No. Size (A) Take Up (B) Length (C) Diameter (D) Jaw Opening (E) Weight Each Limit No. 02048 in. mm in. mm in. mm in. mm in. mm lb kg lb kg 64040 086 640402 0 64040 060 640404 066 64040 062 64040 060 4 02 2 6 8 4 2 4 8 2 26 8 0 6 2 0 4 2 2 6 2 2 0 8 6 6 2 2 4 6 2 2 4 8 22 6 2 6 4 2 0.2 00 22 2 0.2 800 6 8 0.4 200 4 8 6 8 0. 2200 6 2. 00 8 4 6 2 2 4 2 2 4 4 2. 200 26
TURNBUCKLES Stub End Turnbuckles, -S Drop-forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Self-colored Design Factor: to Other Features: Meets design requirements of Federal Specification ASTM F4, Type, Grade, Class C Dimensions Working (Dia.) (Take Up) (Length) Weight/ Cat. UPC No. Load Limit A B W S T U 00 No. 02048 lb kg in. mm in. mm in. mm in. mm in. mm in. mm lb kg 6260 086 00 22 6260 088 200 44 62604 082 2200 8 6260 00004 2200 8 62606 000 2200 8 6260 00028 2200 8 6260 00042 00 88 6260 000 00 88 626 00066 00 88 4 02 0 24 4 4 2 8 0 6 2 6 406 8 8 2 4 02 4 6 2 40 2 6 2 6 406 2 2 22 48 0 2 26 2 2 0 22 2 4 8 6 6 2 6 406 8 200 8 6 22 48 0 8 26 8 6 2 0 22 8 2 8 0 2 8 6 28 6 4 4 6 86 4 4 4 08 2 4 4 4 08 2 6 4 4 4 08 200 4 4 4 08 2 48 6 24 4 6 0 2 08 6 24 4 6 0 286 0 6 24 4 6 0 0 0 626 00080 200 2 6264 000 200 2 626 000 200 2 6268 004 200 266 4 6 2 42 8 4 20 8 2 4 8 6 4 22 20 08 4 286 8 2 4 8 420 4 2 0 2 84 4 2 8 2 4 8 40 222 8 22 6 2 8 4 8 8 2 6 4 6 48 220 6262 006 0000 46 2 6 2 48 22 2 8 2 680 0 62622 002 0000 46 2 2 0 2 6 8 2 8 2 0 4 6262 00202 200 68 8 2 6 2 48 8 244 6 46 4 6 86 448 62626 002 200 68 4 2 6 2 20 08 8 28 6 4 6 60 2 6262 00226 200 68 4 2 2 0 26 660 8 6 4 6 8 62 626 00264 2400 0 2 8 6 2 2 4 248 8 48 8 4 80 6262 002 2400 0 2 8 2 0 2 686 4 400 8 48 8 4 220 022
TURNBUCKLES Turnbuckle Bodies, 0-S, 0-G Drop-forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Self-colored or galvanized to ASTM A- specification Design Factor: to Other Features: Meets design requirements of Federal Specification ASTM F4, Type, Grade, Class B Dimensions Galvanized Working Thread Weight/ Cat. UPC No. Load Limit Dia. B S T 00 No. 02048 lb kg in. mm in. mm in. mm in. mm lb kg 6200 08806 00 22 62002 08806 800 6 6200 08800 200 44 6200 08804 2200 8 62006 08800 2200 8 6200 088 2200 8 6200 088 00 88 6200 08848 00 88 620 088 00 88 4 02 4 4 2 6 8 4 /2 4 6 8 8 0 6 2 8 8 2 6 2 2 2 22 0 2 26 2 2 0 2 4 8 6 6 2 8 200 8 6 22 0 8 26 8 6 2 0 8 2 8 0 6 2 2 22 0 6 4 4 20 4 6 4 0 4 4 0 6 24 0 0 6 24 4 66 6 24 0 620 088 200 2 6204 08886 200 2 620 088 200 2 6208 08822 200 266 4 6 2 8 4 20 8 2 0 68 4 22 4 286 8 2 200 4 2 0 4 2 8 2 20 4 8 22 6 2 8 8 2 6 2 8 6202 08824 0000 46 2 6 2 22 2 8 00 6 62022 08826 0000 46 2 2 0 8 2 8 46 2 6202 08828 0000 46 2 8 4 2 2 8 60 2 62026 08808 200 68 4 2 6 2 8 28 6 4 2 28 6202 088 200 68 4 2 2 0 8 6 4 60 2 62028 08822 200 68 4 2 8 4 2 8 4 6 4 2 420 6202 08860 2400 0 2 8 2 0 4 400 8 48 0 440 These items are made to order.
TURNBUCKLES Turnbuckle Bodies, M-0-ST Drop-forged Type 6 Stainless Steel C Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish A B D Dimensions Working Weight Cat. UPC No. Size (A) Take-up (B) Length (C) Width (D) Load Limit Each No. 02048 in. mm in. mm in. mm in. mm Thread lb kg lb kg 64000 024 4 02 4 4 2 2 2 8 4 x 20 00 22 0.0.00 640002 02800 6 8 4 2 4 2 40 6 2 6 x 8 800 6 0..0 64000 028 8 0 6 2 8 8 2 2 8 x 6 200 44 0.4. 640004 02824 64000 028 64000 02848 2 6 2 2 2 2 8 6 6 2 8 200 8 4 6 2 8 4 20 6 4 2 x 2200 8 0.0.22 8 x 00 88 0..4 4 x 0 200 2.0.68 6400 02862 2 6 2 22 2 4 x 8 0000 44 0 2..24 Turnbuckle Hook End, 8-G Drop-forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Galvanized Right H. Thread Left H. Thread Working For Turnbuckle Thread Length 8-G Hook Dimensions Weight Cat. UPC No. Cat. UPC No. Load Limit Dia.(A) Take Up B C D F G Each No. 02048 No. 02048 lb kg in. mm in. mm in. mm in. mm in. mm in. mm in. mm lb kg 620 086 6240 084 400 8 4 02 2 8 60 /8 8 6 8 0.0.04 620 088 6240 084 000 44 8 0 6 2 6 0 4 46 6 4 8 6 8 0.2. 620 082 6240 08480 00 680 2 6 2 4 6 8 62 8 6 4 2.4.20 620 084 -- -- 00 680 2 2 0 6 4 8 28 8 6 4 2.6.0 620 086 -- -- 200 04 8 6 6 2 4 02 8 8 2 2 2 These items are made to order. 8 22 8 6.80.6
TURNBUCKLES Turnbuckle Jaw End, 888-G Drop-forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Galvanized Right H. Thread Left H. Thread Working For Turnbuckle Weight Cat. UPC No. Cat. UPC No. Load Limit Thread Dia. Take Up Each No. 02048 No. 02048 lb kg in. mm in. mm lb kg 620 080 -- -- 00 22 620 082 6220 088 200 44 620 08220 6220 08864 2200 8 620 08244 -- -- 2200 8 620 082 6220 088 00 88 62 082 -- -- 00 88 4 02.0.0 8 0 6 2.2.0 2 6 2..2 2 2 0.66.0 8 6 6 2.8. 8 6 2 0..2 62 082 622 080 200 2 624 080 6224 08046 200 2 62 082 622 080 200 2 4 6 2.44.6 4 22.. 4 2 0 2.08.4 626 082 -- -- 200 2 4 8 4 2.0.04 62 086 -- -- 200 2 62 084 622 08084 200 266 6220 080 -- -- 200 266 4 24 60.0.8 8 22 2 0 2.4.24 8 22 8 4.00.6 6222 084 -- -- 0000 46 2 2 0 4.0.86 622 088 -- -- 0000 46 2 8 4 4.40 2.00 6224 088 -- -- 0000 46 2 24 60.00 2.2 622 08404 -- -- 200 68 4 2 2 0 6.28 2.8 6228 084 -- -- 200 68 4 2 8 4.86 4.48 62 08442 -- -- 2400 0 2 8 8 4.6. These items are made to order.
TURNBUCKLES Turnbuckle Jaw End, 888-G Drop-forged Carbon Steel Dimensions For Turnbuckles Thread Length 888-G Jaw Dimensions Dia. Take Up B M N P R S U W in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm 4 02 2 8 60 6 00 8 6 2 24 6 2 2 8 6 8 0 6 2 6 0 8 4 6 2 6 4 2 8 22 6 8 2 6 2 4 6 6 60 6 2 4 6 8 8 6 6 0 8 0 2 2 0 6 4 4 2 6 2 4 6 8 8 6 6 0 8 0 8 6 6 2 4 02 6 86 8 6 24 6 4 8 2 8 6 2 0 8 0 6 262 8 6 24 6 4 8 2 8 6 8 4 0 24 6 8 8 6 24 6 4 8 2 4 6 2 4 8 0 8 200 2 8 6 0 2 2 6 24 6 46 8 6 4 22 8 4 8 28 2 8 6 0 2 2 6 24 6 46 8 6 4 2 0 8 8 0 8 26 2 8 6 0 2 2 6 24 6 46 8 6 4 8 4 0 6 2 8 2 2 8 6 0 2 2 6 24 6 46 8 6 4 24 60 6 6 8 42 2 8 6 0 2 2 6 24 6 46 8 6 8 22 2 0 6 86 6 2 4 44 8 8 22 8 4 0 6 262 4 6 4 44 8 2 2 0 2 2 2 8 2 6 2 6 40 2 8 4 0 2 26 2 4 2 6 2 6 40 2 24 60 2 4 8 2 40 2 6 2 6 40 2 8 2 2 2 8 2 2 4 6 0 2 6 6 4 6 0 2 6 6 4 6 0 2 6 6 4 4 8 22 8 22 8 22 4 2 2 0 6 4 4 2 6 62 2 4 2 8 4 0 6 2 6 4 42 2 6 62 2 8 22 4 44 2 8 8 2 8 22 4 44 2 8 8 2 2 8 8 4 0 8 26 8 8 460 2 6 2 6 2 28 2 6 2 8 8
TURNBUCKLES Turnbuckle Eye End, 880-G Drop-forged Carbon Steel Standard Material: Drop-forged carbon steel Standard Finish: Galvanized Right H. Thread Left H. Thread Working For Turnbuckle Weight Cat. UPC No. Cat. UPC No. Load Limit Dia. Take-Up Each No. 02048 No. 02048 lb kg in. mm in. mm lb kg 620 08864 -- -- 00 22 6202 08868 -- -- 800 6 620 08868 6200 08848 200 44 620 08804 6200 08844 2200 8 6206 088 -- -- 2200 8 620 08828 6200 08846 2200 8 620 088 6200 08846 00 88 620 08842 -- -- 00 88 4 02.0.04 6 8 4 2 4..06 8 0 6 2.2. 2 6 2.4.2 2 22..2 2 2 0.8.26 8 6 6 2.80.6 8 6 22.2.42 -- -- 620 088 200 2 62 088 -- -- 200 2 626 08880 -- -- 200 2 4 6 2.20.4 4 2 0.6.4 4 8 4.. 6222 08888 -- -- 0,000 46 2 2 0.2.48 622 08886 -- -- 0,000 46 2 8 4..0 These items are made to order. Turnbuckle Eye End, 880-G Drop-forged Carbon Steel Dimensions Thread Length 880-G Eye Dimensions Dia. Take Up B H I J K in. mm in. mm in. mm in. mm in. mm in. mm in. mm 4 02 2 8 60 6 00 8 0 2 6 2 2 20 6 8 4 /2 4 2 6 68 4 4 2 2 2 2 6 24 8 0 6 2 6 0 8 4 2 6 2 4 6 4 2 22 4 8 4 20 2 2 0 6 4 4 248 8 6 6 2 4 02 6 8 8 6 22 2 40 8 6 22 6 4 4 4 4 2 2 2 2 2 2 2 8 2 6 6 6 6 6 6 2 4 44 2 4 44 4 6 2 4 8 0 8 8 2 2 26 4 2 0 8 8 8 28 2 26 4 8 4 0 6 2 4 8 6 2 26 2 2 0 2 4 2 2 8 4 0 2 26 6 4 4 2 8 6 2 8 4 8 6 2 8 4 8 6 2 8 4 8 22 6 8 22 6
JAM NUTS Jam Nuts (Lock Nuts) 0-G Right Hand Thread Left Hand Thread Weight per Size UPC No. UPC No. 00 Pcs. in. mm Cat. No. 02048 Cat. No. 02048 Finish Packed lb kg 6200 060 620 046 Galvanized Bulk 0.4 8 0 6200 084 -- -- Galvanized Bulk 2 0. 2 62004 0 6204 040 Galvanized Bulk. 8 6 6200 040 620 006 Galvanized Bulk 2.2 4 62006 044 6206 0 Galvanized Bulk 8.6 8 22 6200 042 620 020 Galvanized Bulk 2.4 2 62008 048 6208 0 Galvanized Bulk 8 8. 4 2 6200 044 620 044 Galvanized Bulk 6 6. These items are made to order
CONNECTING LINKS Connecting Links 2-S, G, A Regular -S Pear Shaped Stainless Regular READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING CONNECTED LINKS. Campbell carbon and alloy steel connecting links are all drop-forged and heat treated. Galvanizing is to ASTM A- specification. Campbell stainless connecting links are all drop-forged and made of 6 Stainless Steel, and have an electropolished finish. Connecting links are used to connect two pieces of chain or to connect a fitting to a chain. IMPORTANT: Instructions For Use. Make sure the connecting link used is the same size as the components being joined, e.g., a /8 in. connecting link is used with /8 in. chain. 2. To effectively close the connecting link, peen the prongs (using a ball peen hammer) to fill the hole of the mating half as much as possible.. Any assembly made using connecting links should be rated at the working load limit (WLL) of the weakest component. 4. Do not exceed WLL. See table below.. The WLL of connecting links is based on a straight line pull. Any side or shock loading will significantly reduce the actual WLL. REGULAR CONNECTING LINK PEAR SHAPED CONNECTING LINK Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Use connecting links only as indicated. Do not use connecting links for overhead lifting. Never re-use connecting links. Connecting links must always be inspected for wear, distortion and tightness before use. If worn, distorted or damaged, discard and replace. Working Load Limits (lbs and kg) - Connecting Links Regular Pear Shaped Carbon Carbon Steel Alloy Steel Size WLL WLL WLL in. mm lb kg lb kg lb kg 6 800 6 * * 400 66 * * 6 8 2000 08 000 62 * 8 0 2800 2 4200 0 80 840 6 62 646 400 242 * 2 40 2 000 8 00 48 8 6 20 22 0800 40 000 220 4 020 464 000 680 00 22 8 22 2000 448 8000 82 600 48 2 00 0 24000 086 * 4 2 24000 086 * * * Item not manufactured.
CONNECTING LINKS 2-S, 2-G, 2-A Connecting Links, Carbon Steel and Alloy Steel Standard Material: Forged carbon and alloy steel - Heat Treated Standard Finish: Self-colored or galvanized Design Factor: 4 to For effective closure peen to fill eye of mating half as much as possible Meets design requirements of Federal Specification RR-C-2D, Type II Carbon Steel, Heat Treated Self Colored Galvanized Working Dimensions Links Weight/ Size Cat. UPC No. Cat. UPC No. Load Limit A B C D Per 00 in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm in. mm Box lb kg 6 20004 046 2004 04660 800 6 4 8 2 6 8 8 6 20 200404 046 20044 04684 400 6 2 2 8 6 8 22 0 6 6 8 20004 046 2004 040 2000 0 6 0 4 44 8 0 200604 044 20064 042 2800 20 8 2 8 4 6 20004 048 2004 044 62 644 6 40 2 8 60 2 200804 042 20084 046 40 2 2 2 44 2 6 68 8 6 20004 040 2004 04806 20 28 2 8 4 8 86 4 20204 048 2024 04820 020 464 2 2 64 8 8 2 2 0 0 6 4 8 2 0 8 8 8 6 4 2 0 26 2 2 2 6 0 8 6 2 8 48 0 2 2 2 2 8 4 2 8 22 2040 048 204 04844 2000 44 2 6 4 2 4 6 0 2 2 64 Bulk 4 2 2060 048 206 04868 00 0 6 84 2 4 2 2 4 0 Bulk 240 0 4 2 20200 048 2020 04882 24000 0886 4 02 6 8 6 2 8 4 8 Bulk 464 2 Alloy Steel, Heat Treated Self Colored Working Dimensions Links Weight/ Size Cat. UPC No. Load Limit A B C D Per 00 in. mm No. 02048 lb kg in. mm in. mm in. mm in. mm Box lb kg 6 -- -- -- -- 4 8 2 6 8 8 6 20 -- -- -- -- 2 2 8 6 8 22 0 6 6 8 2080 000 000 6 6 0 4 44 8 0 20860 008 4200 0 8 2 8 4 6 2080 002 400 244 6 40 2 8 60 2 20880 002 000 2 2 44 2 6 68 8 6 2000 004 0800 48 2 8 4 8 86 4 2020 006 000 6804 2 2 64 8 8 2 2 0 0 6 4 8 2 0 8 8 8 6 4 2 0 26 2 2 2 6 0 8 6 2 8 48 0 2 2 2 2 8 4 2 8 22 2040 006 8000 86 2 6 4 2 4 6 0 2 2 64 Bulk 4 2 2060 000 24000 0886 6 84 2 4 2 2 4 0 Bulk 240 0 4 2 -- -- -- -- 4 02 6 8 6 2 8 4 8 Bulk 464 2
M-48-ST Connecting Links, Stainless Steel CONNECTING LINKS Standard Material: Forged Type 6 Stainless Steel Standard Finish: Electro-polish For effective closure, peen to fill eye of mating half as much as possible Working Dimensions Weight Size Cat. UPC No. Load Limit A B C D Each in. mm No. 02048 lb kg in. mm in. mm in. mm in. mm lb g 64004 6 600 22 2 2 8 6 8 22 0.0 2 6 8 6400 660 00 408 6 0 4 44 8 64006 04422 440 6 8 2 8 4 2 2 0.2 4 6 4 8 2 0.8 82 -S, -G Pear Shaped Connecting Links Standard Material: Forged carbon and alloy steel - Heat Treated Standard Finish: Self-colored or galvanized Design Factor: 4 to For effective closure, peen to fill mating half as much as possible Carbon Steel, Heat Treated Self Colored Galvanized Working Dimensions Weight/ Size Cat. UPC No. Cat. UPC No. Load Limit B C D E 00 in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm in. mm lb kg 8 0 20604 040 2064 042 80 8 2 6 6 2 2 6 4 2 2 20804 042 2084 046 00 4 8 2 2 2 2 64 6 4 20 8 6 20600 044 2060 040 000 2268 4 4 08 8 2 2 4 0 6 2 4 4 20620 046 2062 044 00 22 4 8 24 4 2 8 2 0 8 22 20640 048 2064 048 600 4 6 44 2 8 /6 4 4 2 220 00 Alloy Steel, Heat Treated Galvanized Working Dimensions Weight/ Size Cat. UPC No. Load Limit B C D E 00 in. mm No. 02048 lb kg in. mm in. mm in. mm in. mm lb kg 8 0 206 048 000 6 2 6 6 2 2 6 4 2 2 208 822 000 2268 8 2 2 2 2 64 8 6 2040 8 8000 62 4 4 08 8 2 2 /4 0 6 4 20 6 2 4 4 2042 846,000 40 4 8 24 4 2 8 2 0 8 22 2044 8,000 6804 6 44 2 8 /6 4 4 2 220 00 These items are made to order
HOOKS Grab/Slip Hooks 4, 4-A Eye Grab; 4, 4-A Clevis Grab; 44, 44-A Eye Slip; 46, 46-A Clevis Slip READ AND UNDERSTAND THESE S AND INSTRUCTIONS BEFORE USING GRAB AND SLIP HOOKS. Campbell grab and slip hooks are all drop-forged and heat treated. The alloy eye grab hooks meet the design requirements of Federal Specification RR-C-2. IMPORTANT: Instructions For Use. These hooks are designed to engage chain and are sized by the material diameter of the chain that they engage. Make sure hook size and chain diameter are compatible before lifting load. 2. Grab hooks are designed to grab a chain link and hold it in place.. Slip hooks are designed to allow chain to slip through the hook. 4. Only use genuine Campbell parts when replacing clevis pins and cotter keys.. Do not exceed working load limit (WLL). See table below. Failure to follow the Instructions For Use below and these warnings may cause death or serious injury. Use these hooks only as indicated. Never point load a hook. Do not use hooks for lifting personnel. Hooks must always be inspected for wear, distortion and damage before use. If worn, distorted or damaged, discard and replace. Always stand clear of loads being lifted. Working Load Limits (lb and kg) Hooks System & System 4 Heat Treated Alloy Eye & Clevis Grab, Eye & Clevis Clevis Clevis Eye Slip Slip Eye Slip Grab Slip Size WLL WLL WLL WLL WLL in. mm lb kg lb kg lb kg lb kg lb kg 2400 00 2600 80 400 44 400 86 400 86 6 8 00 8 00 4800 2 00 2 00 2 8 0 4600 2088 400 242 6400 206 00 22 00 4 6 600 242 200 26 8000 62 0000 440 0000 440 2 400 60 200 4 0000 440 2000 448 000 02 8 6 0000 440 00 22 400 68 800 82 2000 26 4 - - 6200 - - 2800 2848 - -
HOOKS 4, 4-A Eye Grab Hooks Drop-forged micro-alloy steel (system & 4) or alloy steel Standard Finish: System & 4 hooks available with blu-krome or self-colored finish. Alloy hooks are heat treated, and painted orange Alloy hooks meet the design requirements of Federal Specification RR-C-2 S/C finish hooks are bulk packed, blu-krome hooks are packed 0 per box Order unit is "Each" 4, System & 4 Chain Self-colored (Bulk) Blu-Krome (0/Box) Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Load Limit B E R Each in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm lb kg 4004 000 4000424 02888 2600 2 2 8 48.2.2 6 8 400 006 400024 022 00 6 8 0 4006 0 4000624 026 400 244 6 400 020 -- -- 200 266 2 4 2 2 20 6 2 6 6.4.2 /2 2 2 6..2 2 2 8..0 2 4008 0 -- -- 200 4 8 2 8 6 400 044 -- -- 00 26 2 4 402 0 -- -- 6200 48 6 2 2 8 86.. 2 2 20 4 2 0.2.4 6 24 8 0 6.0 2.86 4-A, Alloy Steel - Heat Treated Chain Alloy, Orange (Bulk) Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Load Limit B E R Each in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm lb kg 404 0 -- -- 400 860 2 2 8 48.2.2 6 8 40 082 -- -- 00 22 8 0 406 0 -- -- 00 22 6 40 020 -- -- 0000 46 2 4 2 2 20 6 2 6 6.4.2 /2 2 2 6..2 2 2 8..0 2 408 022 -- -- 2000 44 8 2 8 6 40 022 -- -- 800 820 2 4 42 026 -- -- 2800 82 6 2 2 8 86.. 2 2 20 4 2 0.2.4 6 24 8 0 6.0 2.86
HOOKS Drop-forged micro-alloy steel (system & 4) or alloy steel Standard Finish: System & 4 hooks available with blu-krome or self-colored finish. Alloy hooks are heat treated with a self-colored finish Design factor: Carbon hook is 4 to. Alloy hook is -/2 to S/C hooks are bulk packed, blu-krome hooks are packed 0 per box Order unit is "Each" 44, 44-A Eye Slip Hooks 44, System & 4 Chain Self-colored (Bulk) Blu-Krome (0/Box) Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Load Limit B E R Each in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm lb kg 40040 048 4200424 028 2400 08 2 6 24 2 6 6.44 0.20 6 8 4000 046 420024 028 00 88 8 0 40060 002 4200624 066 4600 208 6 4000 0 -- -- 600 240 2 40080 026 -- -- 400 2 2 8 2 2 4 0.6 0.2 6 4 2 4 8.00.0.4 4 2 8 8 8.80 0.82 8 22 4 44 4 6 0 2.60.8 8 6 4000 0 -- -- 0000 46 6 2 2 2 4.0.86 44-A, Alloy Steel - Heat Treated Chain Alloy, Orange (Bulk) Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Load Limit B E R Each in. mm No. 02048 No. 02048 lb kg in. mm in. mm in. mm lb kg 404 040 -- -- 400 42 2 6 24 2 6 6.44 0.20 6 8 40 0 -- -- 4800 2 8 0 406 064 -- -- 6400 20 6 40 0 -- -- 8000 62 2 408 088 -- -- 0000 46 2 2 8 2 2 4 0.6 0.2 6 4 2 4 8.00.0.4 4 2 8 8 8.80 0.82 8 22 4 44 4 6 0 2.60.8 8 6 40 0 -- -- 400 6 6 2 2 2 4.0.86
HOOKS Clevis Grab Hooks 4, 4-A Standard Material: Drop-forged carbon steel steel (system & 4) or alloy steel Standard Finish: System & 4 hooks available with blu-krome or self-colored finish. Alloy hooks are heat treated, and painted orange and stamped "Alloy" S/C finish hooks are bulk packed, blu-krome hooks are available packed 0 per box or individually bagged and sold in shelf packs of 0 Order unit is "Each" 4, System & 4 Chain Self-colored (Bulk) Blu-Krome (0/Box) Blu-Krome, Bagged Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Cat. UPC No. Load Limit B E P R Each in. mm No. 02048 No. 02048 No. 02048 lb kg in. mm in. mm in. mm in. mm lb kg 40040 088 400424 082 B0424 488 2600 8 0 2 6 8 2 2 44 0.2 0. 6 8 4000 022 40024 0 B024 404 00 6 2 2 6 8 0 2 0 0. 0.2 8 0 40060 060 400624 0 B0624 664 400 244 2 2 6 2 4 0.2 0.42 6 4000 04004 -- -- -- -- 200 266 2 2 2 2 8 6.2 0.60 2 40080 04042 400824 040 -- -- 200 4 2 2 2 2 6 64 2.00 0. 8 6 4000 040 -- -- -- -- 00 26 6 2 2 2 20 4 2 2 6.0. 4 4020 040 -- -- -- -- 6200 48 6 24 6 24 6 2 4 2 2 2 6.2 2.8 4-A, Alloy Steel - Heat Treated Chain Alloy, Orange (Bulk) Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Cat. UPC No. Load Limit B E P R Each in. mm No. 02048 No. 02048 No. 02048 lb kg in. mm in. mm in. mm in. mm lb kg 40 040 -- -- -- -- 400 860 8 0 2 6 8 2 2 44 0.2 0. 6 8 404 040 -- -- -- -- 00 2 2 2 6 8 0 2 0 0. 0.2 8 0 40 042 -- -- -- -- 00 22 2 2 6 2 4 0.2.0.42 6 406 044 -- -- -- -- 0000 46 2 2 2 2 8 6.2 0.60 2 40 044 -- -- -- -- 2000 44 2 2 2 2 6 64 2.00 0. 8 6 408 048 -- -- -- -- 800 820 6 2 2 2 20 4 2 2 6.0. 4 40 046 -- -- -- -- 2800 28 6 24 6 24 6 2 4 2 2 2 6.2 2.8
HOOKS Clevis Slip Hooks 46, 46-A Standard Material: Drop-forged carbon steel steel (system & 4) or alloy steel Standard Finish: System & 4 hooks available with blu-krome or self-colored finish. Alloy hooks are heat treated, and painted orange and stamped "AH" S/C finish hooks are bulk packed, blu-krome hooks are available packed 0 per box or individually bagged and sold in shelf packs of 0** Order unit is "Each" Design Factor: Carbon steel hooks is 4 to. Alloy steel hooks is -/2 to 46, System & 4 Chain Self-colored (Bulk) Blu-Krome (0/Box) Blu-Krome, Bagged Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Cat. UPC No. Load Limit B E P R Each in. mm No. 02048 No. 02048 No. 02048 lb kg in. mm in. mm in. mm in. mm lb kg * 440040 068 4400424 062 B42 6 2600 * 6 8 44000 066 440024 066 B2 660 00 6 * 8 0 440060 064 4400624 000 B62**668 400 244 6 44000 0 440024 048 -- -- 200 266 8 0 6 24 6 6 2 2 4 2 6 2 8 6 8 2 2 44 0. 0.4 8 0 6.00 0.4 6 2 8.40 0.64 2 8 2 2.00 0. 2 440080 0 4400824 086 -- -- 200 4 8 6 44000 080 -- -- -- -- 00 26 * Hooks have drilled hole for latch kit. See page 04 for latch kits. ** Shelf pack is 8 6 4 44 4 2 6 4 2 04.0.4 4 4 6 22.20 2.6 46-A, Alloy Steel - Heat Treated Chain Alloy, Orange (Bulk) Working Dimensions Weight Size Cat. UPC No. Cat. UPC No. Cat. UPC No. Load Limit B E P R Each in. mm No. 02048 No. 02048 No. 02048 lb kg in. mm in. mm in. mm in. mm lb kg * 440 086 -- -- -- -- 400 860 * 6 8 4404 082 -- -- -- -- 00 2 * 8 0 440 080 -- -- -- -- 00 22 6 4406 084 -- -- -- -- 0000 46 8 0 6 24 6 6 2 2 4 2 6 2 8 6 8 2 2 44 0. 0.4 8 0 6.00 0.4 6 2 8.40 0.64 2 8 2 2.00 0. 2 440 084 -- -- -- -- 000 8 8 6 4408 086 -- -- -- -- 2000 208 * Hooks have drilled hole for latch kit. See page 04 for latch kits. 8 6 4 44 4 2 6 4 2 04.0.4 4 4 6 22.20 2.6