Installation instructions, accessories Instruction No 8685714 Version 1.0 5 Part. No. RTI S80 Volvo Car Corporation RTI S80-8685714 - V1.0 Page 1 / 25
Equipment A0000161 A0000162 A0801178 D8802049 Page 2 / 25
D3903544 Page 3 / 25
D3903545 Page 4 / 25
D3903546 Page 5 / 25
M3903789 Page 6 / 25
INTRODUCTION Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer. Note! This accessory is connected to the electrical system of the car. It requires software unique to the car. Note! There is already a cable harness for the power supply for the CD changer in cars with CD changers. This cable harness must be disconnected. The new cable harness supplies power to both the CD changer and to the RTI/DVD and must be connected in the same position as the old cable harness. This is carried out in points 20, 23, 24, 25, 26. Preparations 1 Preparations Applies to cars with power seats Move the left front seat to its rearmost position. 2 Turn the ignition key to position 0 Remove the key from the ignition switch (does not apply to cars with automatic gearboxes) Page 7 / 25
Disconnect the battery negative lead. Note! Wait at least five minutes before disassembling the connectors or removing other electrical equipment. A8800136 3 Carefully remove the loudspeaker grille (1) on the dashboard. Use a weatherstrip tool or similar. D8502029 4 Remove the screws (1). Remove the bracket (2). D8502030 5 Applies to cars with a centrally mounted loudspeaker Page 8 / 25
Remove the three screws in the loudspeaker (1) Lift up the loudspeaker. Disconnect the connector (2) Place the loudspeaker to one side. D3902021 6 Detach the panel (1) and the gear selector lever boot using a weatherstrip tool. D8502224 7 Move the gear selector lever to its rearmost position Pull the panel (1) and the boot backwards. Turn the panel as illustrated Remove the screws (2) from the dashboard environment panel. M8503890 Page 9 / 25
8 Angle the dashboard environment panel outwards so that it is possible to insert a couple of fingers between the centre console and the reverse of the panel Remove the dashboard environment panel by pulling it downward, maintaining the same angle. Some force is required because the panel is tightly installed Disconnect the connectors on the reverse of the dashboard environment panel. Place the dashboard environment panel to one side. Note! D8703527 If any of the outer hooks break off, these must be repaired. The method for this can be found in the Workshop Manual in the section about the dashboard. 9 Remove the screws (1) from the radio bracket Pull out the bracket and radio. Pull the lower corner while pressing downwards Disconnect the connectors on the radio. Place the bracket and the radio to one side. D8503946 10 Move the left front seat to its rearmost position Remove the left side panel (1) from the centre console by turning the clip and pulling the panel outwards and backwards Remove the sill trim panel (2) at the left-hand front door Remove the cover (3) and the screws (4) for the front mountings in the left-hand front seat. Page 10 / 25
D8502410 11 Tip the left-hand front seat backwards Push the floor carpet to one side so that the air ducts (1) are accessible. D8502411 12 Remove the seat cushion from the left-hand rear seat(1). Lift the front edge of the cushion and then pull forwards Remove the sill trim panel (2) at the left-hand rear door. D8502766 13 Remove the seat belts from the guide (1) on the right and lefthand side cushions Insert a hand down the side of the lower section of the left side cushion. Release the catches while lifting the side cushion. Place the cushion to one side Fold both backrests forward. Page 11 / 25
D8502763 14 Carefully lift the front edge of the parcel shelf panel until the clips (1) release Lift up the parcel shelf further until the locating pins (2) release from their holes Pull out the parcel shelf. Lay the parcel shelf on the folded backrests. M8503611 15 Lift out the cargo compartment carpet Press the centres of the clips at the bottom of the folding side panel on the left-hand side. Press the clips until a click is heard Remove the two clips Remove the plastic nut at the front edge of the side panel Repeat the operation on the right-hand side. M8902133 16 Turn the handle (1) on the right and left-hand sides. Turn the handle through 90. Fold the side panels down. Lift the panels out. Place the lefthand side panel to one side (there is a new panel in the kit) Remove the two covers (2). Remove the screws (3) in the sill trim panel Grip the outer edges of the sill trim panel (4). Pull the panel inwards towards the centre so that the clips release from the Page 12 / 25
sides Disconnect the connectors (5) for the cargo compartment lamps Remove the sill trim panel. Pull the sill trim panel straight upwards so that the clips release from the rear cross member. D8502376 17 Remove the clips (1) and the plastic nut in the left front side panel in the cargo compartment. It is easiest to access the front upper clip from the side of the rear seat Remove the front side panel. M8503515 18 Applies only to cars with a CD changer Remove the four screws (1) in the bracket for the CD changer Remove the CD changer with the bracket Remove the DIN cable and the cable with the blue connector from the rear end of the CD changer. D3903553 Cable routing 19 Cable routing Route the wiring (A in the kit illustration) for the display screen and the radio, and the loose cable for the display screen with the Page 13 / 25
ten pin connectors (B in the kit illustration) to the radio socket between the air duct (1) and the stay (2). Ensure that the straight connector on the loose cable (B) is routed to the cut out for the radio Route the green 5-pin power supply connector (3) for the display screen and the cable (B) to the left of the air ducts above the hole for the radio. Continue up through the cut out for the dashboard loudspeaker Secure the wiring in the stay (2). Use a tie strap (4) D3702796 Route the wiring above and along the air duct (1) to the member (5) Clamp the wiring at the existing cable harness (6). Use a tie strap. 20 Route both cables (A and B in the kit illustration) under the carpet. Continue along the left-hand side of the car to the rear door Install the protective caps on the lugs (1) for the cable ducts Route the wiring further above and along the front cable duct (2). Continue along the right hand side of the rear cable duct (3) Connect the ground lead to the rear ground terminal (4) on the left side of the rear seat. Tighten the screw. Tighten to 10 Nm (7.4 lbf. ft). Applies only to cars with a CD changer D3702797 Disconnect the existing ground lead and secure it out of the way. 21 Route the wiring (A and B) under the wiring at the cable duct (1). Continue out through the hole in the car body by the front edge of the wheel arch Route the wiring along the inside of the cable duct (2) and the insulation panel by the wheel arch in the cargo compartment Pull forwards and position the wiring as illustrated. D3702798 Page 14 / 25
22 Applies to cars without a CD changer Install the small bracket (1) (for the DVD reader bracket) onto the rear cross member under the left tail lamp. Use the screw (2) from the kit. D8100982 Connection in the fuse holder 23 Connection in the fuse holder Remove the rear electronic module. First open the catch (1) on the top of the module. Fold the module forward. Lift the module from the mountings (2). M3702263 24 Applies only to cars with a CD changer Remove all the fuses (1) from the outside of the fuse holder. Page 15 / 25
D3702799 25 Applies only to cars with a CD changer Remove the decal from the face of the fuse holder Carefully pry up the red secondary lock until it clicks. M3702784 26 Applies only to cars with a CD changer Insert a small screwdriver in the outer terminal in fuse socket number 10 Locate the small spring catch on the inside Bend the catch out of the way by inserting the screwdriver in the direction of the arrow. At the same time pull the existing cable out Connect the new routed red and white (R/W) cable. Press in the secondary locking. Reinstall the decal on the face. D3702786 27 Connect the new routed red and white cable to the outer terminal (1) on the reverse of fuse socket number 10 on the fuse holder. Carefully pry up the red secondary locking on the face in the end nearest terminal 10. At the same time press the cable into position. Hint If there is a problem inserting the cable, carry out the procedures for removing the cable according to points 24-26. Page 16 / 25
Install a 10 A fuse in fuse socket 10 on the fuse holder. M3702534 28 Slacken off the screw (1) Pull out the cover (2) and the four connectors Remove the cover from the four connectors by bending the three hooks to one side. D3701827 29 Insert a small screwdriver in the socket on connector A as illustrated Twist the screwdriver so that the holders open. At the same time press the connector out to the side Connect the white (W) cable to terminal 15 and the green (GN) cable to terminal 17. Reinstall: the connector the cover on the connector the connectors on the rear electronic module. Tighten the screw M3702569 the rear electronic module. Installing and connecting the Global Positioning System (GPS) aerial 30 Installing and connecting the Global Positioning System (GPS) aerial Page 17 / 25
Install the new Global Positioning System (GPS) aerial (1) in the guide hole. Press the Global Positioning System (GPS) aerial into place using the clip in the hole in the centre of the rear edge of the parcel shelf. See the illustration Route the new cable (C in the kit illustration) to the Global Positioning System (GPS) aerial. Follow the routing of the existing loudspeaker cable inside the seat belt holder (2) Connect the cable to the Global Positioning System aerial Secure at the points (3) D3702820 Route the cable through the lead-in (4) to the rear edge of the wheel arch. Installing the DVD reader 31 Installing the DVD reader Secure the pre-routed cable harness at the cable duct using two tie straps (1) Secure the blue connector (this will not be used) together with the cable harness that was connected to the fuse holder at the cable harness for the fuse holder. Use a tie strap (2). Applies only to cars with a CD changer Secure the cable harness at the cable duct. Use two tie straps (1) D3903555 Secure the blue connector, disconnected from the CD changer, together with the cable harness connected to the fuse holder at the cable harness for the fuse holder. Use a tie strap (2). 32A Take four screws, the bracket and the DVD reader from the kit. Tighten the DVD reader at the bracket. Illustration 32B applies to cars with a CD changer Secure the DVD reader by the bracket for the CD changer. Use four screws from the kit. D3903542 Page 18 / 25
32B D3903543 33A Install the bracket with the DVD reader behind the wheel arch. Use four screws (1) from the kit. See the illustration. Tighten the screws. Tighten to 10 Nm (7.4 lbf. ft). Illustration 33B applies to cars with a CD changer Install the bracket with the CD changer / DVD reader behind the wheel arch. Use the four screws (1) from the kit. See the illustration. Tighten the screws. Tighten to 10 Nm (7 lbf. ft.). 33B D3903547 D3903562 Page 19 / 25
Connecting the DVD reader 34A Connecting the DVD reader Connect: the cable (1) for the display screen the power supply cable (2) (green connector) the cable (3) for the Global Positioning System (GPS) aerial the DIN cable (4) for the radio Secure the cable harness at the cable duct. Use a tie strap (5) as illustrated. Illustration 34B applies to cars with a CD changer 34B D3903556 Connect: the cable (1) for the display screen the power supply cable (2) (green connector) for the DVD reader the cable (3) for the Global Positioning System (GPS) aerial the short DIN cable (4) (purchased separately) between the CD changer and the DVD reader the blue connector (5) to the power supply for the CD changer the DIN cable (6) previously disconnected from the CD changer Secure the cable harnesses using a tie strap (7). M3903558 35 Does not apply to USA Take the aerial amplifier (1) from the kit. Connect the cable (2) to the connector (3) for the aerial in the rear bumper by the righthand tail lamp Position the aerial amplifier on the panel edge in front of the righthand tail lamp Tighten the aerial amplifier onto the edge of the panel. Page 20 / 25
M3903315 36 Does not apply to USA Take the transparent cable (D in the kit illustration) from the kit Connect the green connector (1) to the DVD reader Route the cable under the bracket for the DVD reader, continue along the cable harness in the rear cross member and forwards to the right-hand tail lamp Connect the cable to the lower socket (2) on the aerial amplifier Secure the cable at the rear cross member and under the bracket for the DVD reader. Use tie straps (3). M3903559 Installing and connecting the display screen 37 Installing and connecting the display screen Applies to cars without a centrally mounted loudspeaker Install the bracket (1) on the display (2). Only use screws at position (3) and screw and washer at position (4). Screws and washer can be found in the kit. Applies to cars with a centrally mounted loudspeaker Install the bracket (1) on the display screen (2). Use the front screw (3). M3904284 38 Applies to cars without a centrally mounted loudspeaker Connect the wiring for the DVD reader (1) to the display (2) Install the display screen and the bracket in the dashboard. Use the existing screws (3) Press the new loudspeaker grille (from the kit) into place on the Page 21 / 25
dashboard. D3903561 39 Applies to cars with a centrally mounted loudspeaker Install the centrally mounted loudspeaker in the cut out in the bracket for the display screen Tighten the loudspeaker into place. Use the four screws Press the connector (1) for the centre loudspeaker into the bracket on the left-hand under side of the display screen bracket. M3903539 40 Applies to cars with a centrally mounted loudspeaker Connect the three cables (1) to the display screen and the centrally mounted loudspeaker Press the display screen and bracket into the dashboard. Tighten using the three existing screws (2) Press the new loudspeaker grille (from the kit) into place on the dashboard. D3903560 Finishing work 41 Finishing work Page 22 / 25
Connect the green female connector on the new cable harness, to the green male connector disconnected from the radio Connect the other two large connectors to the radio Connect the other connectors removed from the radio Reinstall the radio Connect the connectors to the dashboard environment panel. Reinstall the panel Reinstall the panel and gear selector lever boot around the gear selector lever Fold the carpet at the left-hand front seat back into position Reinstall the side panel on the centre console Reinstall the sill trim panel in the left-hand front and rear doors Fold the left-hand front seat back into position Tighten the screws in the front edge of the seat. Use new screws from the kit. Tighten to 40 Nm (30 lbf. ft). Reinstall the covers over the screws Reinstall the parcel shelf Connect the connectors for the cargo compartment lamps on the rear cross member panel. Reinstall the cross member panel Reinstall the left-hand front side panel in the cargo compartment Reinstall the right-hand folding panel and a new left-hand folding panel from the kit Reinstall the side cushion Fold the backrest back into place Reinstall the seat cushion. 42 Slacken off both the spring loaded screws (1) on the reverse of the steering wheel using a Torx T30 screwdriver Slacken off the screws so that the threads release and the screws spring back Fold out the steering wheel module (2). Note! Do not damage the wiring. D8501891 Page 23 / 25
43 Disconnect the SRS connectors (1) for the ignition cables from the steering wheel module. Press in the catches on the sides and then carefully pull the connectors straight back. Note! The connectors are securely positioned-. Do not use tools when removing. Disconnect the horn connector (2). M8802750 44 Replace the steering wheel with a steering wheel with RTI controls (purchased separately) according to the installation instructions provided with the steering wheel. 45 Connect the installed keypad connector to the corresponding terminal on the steering wheel module keypad on the right-hand side. D3903790 46 Connect the connector (2) to the relevant connector on the steering wheel module Carefully reinstall the ignition cables (1) for the SRS (supplemental restraint system) on the steering wheel module according to point 43 Position the steering wheel module. Check that no cables are Page 24 / 25
trapped. 47 Install the screws on the reverse of the steering wheel. Tighten the screws. Tighten to 10 Nm (8 lbf. ft.). D8502517 48 Turn the ignition key to position II Reconnect the battery negative lead Program the software according to the service information in VIDA. A8800137 Page 25 / 25