E-CPM8-PL-02 REVISED STARTING SERIAL # 200074 PARTS LIST MANUAL MODEL CPM8 GASOLINE MODEL ELECTRIC MODEL 8 WALK BEHIND SCARIFIERS SKU # MODEL # POWER OPTION 79300 CPM8-9H HONDA GASOLINE ENGINE MODEL GX270 79500 CPM8-5B/230/ BALDOR ELECTRIC MOTOR 5HP 60Hz PH 230V 79400-230 CPM8-5B/230/3 BALDOR ELECTRIC MOTOR 5HP 60Hz 3PH 230V 79400-460 CPM8-5B/460/3 BALDOR ELECTRIC MOTOR 5HP 60Hz 3PH 460V 79400-50/220 CPM8-5B/50/220/3 BALDOR ELECTRIC MOTOR 5HP 50Hz 3PH 220V 79400-50/380 CPM8-5B/50/380/3 BALDOR ELECTRIC MOTOR 5HP 50Hz 3PH 380V 79400-50/440 CPM8-5B/50/440/3 BALDOR ELECTRIC MOTOR 5HP 50Hz 3PH 440V
E-CPM8-PL-02 ILLUSTRATION : MAIN GROUPING
PARTS LISTING - ILLUSTRATION : MAIN GROUPING E-CPM8-PL-02 6500 MAIN FRAME, CPM-8 2 6504 AXLE SHAFT 3/4 DIA. X 2-7/32 L 3 0428 COLLAR, LOCKING 3/4 ID 2 4 5200 WHEEL 4 X -/2 X 3/4 BRG. 2 5 0045 WASHER, LOCK /2 ZINC 2 6 0304 SCREW, CAP /2-20 X 2 7 65003 COVER, BELT, CPM-8 8 65022 PLUG, HOLE 2 9 6525 SCREW, CAP /2-3 X 5-/4 2 0 6506 SPACER TUBE /2 ID X 3-9/6 L,CPM-8 2 047 NUT, HEX /2-3 ZINC 2 2 032 WASHER, FLAT /2 SAE ZINC 4 3 0045 WASHER, LOCK /2 ZINC 2 4 0865 NUT, ACORN /2-3 2 5 65002 MOUNT, ENGINE/MOTOR, CPM-8 6 0909 BOLT, CARRIAGE 3/8-6 X 3 FULL THD. 7 0404 NUT, HEX 3/8-6 ZINC 8 0802 BOLT, CARRIAGE 3/8-6 X FULL THD. 2 9 0025 WASHER, FLAT 3/8 SAE ZINC 2 20 08 WASHER, LOCK 3/8 ZINC 2 2 0404 NUT, HEX 3/8-6 ZINC 2 22 002 SCREW, CAP 3/8-24 X 2 23 0025 WASHER, FLAT 3/8 SAE ZINC 4 24 0004 NUT, HEX LOCK 3/8-24 ZINC 2 25 65009 HANDLE BAR, CPM-8 26 0608 GRIP, HAND.937 X 4.5 BLK VYNAFOAM 2 27 0808 FITTING, GREASE /4-28 STRAIGHT (SEE ILLUS. 2) 28 0025 WASHER, FLAT 3/8 SAE ZINC 4 29 08 WASHER, LOCK 3/8 ZINC 4 30 0055 SCREW, CAP 3/8-6 X 4 3 86347 BRACKET, MULTI-VAC PORT 2-3 32 6502 CAP/PLUG 2 RED PLASTIC, FLANGED 33 0038 WASHER, LOCK /4 ZINC 2 34 0846 SCREW, CAP STSHW /4-20 X /2 2 35 65098 HOSE, FLEX 2 ID X 22 L 36 0766 CLAMP, HOSE, SAE #32, ADJ. TO 2-/2 2
E-CPM8-PL-02 ILLUSTRATION 2: REAR FORK & CONTROL LINKAGE GROUPING
E-CPM8-PL-02 PARTS LISTING - ILLUSTRATION 2: REAR FORK & CONTROL LINKAGE GROUPING 4023 KNOB, BALL -3/8 W/ /2-3THD, BLK. 2 2 04 SCREW, SKT. HD. CAP /2-3 X 4 ZINC 3 50550 SLEEVE, BRASS /2 TAPERED 4 6509 HANDWHEEL, SMALL W/ 5/8-8 X 3 ROD 5 85005 BEARING, THRUST BALL 5/8 6 0073 WASHER, FLAT 5/8 SAE ZINC 4 7 65007 LINKAGE SUPPORT, UPPER 8 0359 SCREW, CAP 5/8- X 3-/4 9 79035 BUSHING, RUBBER -/6 X 5/8 X /4 0 027 SCREW, DRIVE /8 X /4 L 0808 FITTING, GREASE /4-28 STRAIGHT 2 2 0096 COLLAR, LOCKING 5/8 ID 3 65006 LINKAGE, LOWER, CPM-8 4 65004 FORK, CPM-8 5 65005 SPACER, REAR WHEEL, 2-/8 2 6 5200 WHEEL 4 X -/2 X 3/4 BRG. ALUM/RUB 2 7 0306 PIN, COTTER 3/6 X -/2 2 8 800 SCREW, CAP /2-3 X 4 9 0407 NUT, HEX LOCK /2-3 ZINC 2 20 6505 SCREW, CAP /2-3 X 8 ZINC 2 032 WASHER, FLAT /2 SAE ZINC 2
E-CPM8-PL-02 ILLUSTRATION 3: WATER SYSTEM KIT PART # 65080 OPTIONAL 8002 CONN., SWIVEL FEM. 3/4HOSE X /2MPT 2 07 VALVE, BALL /2 FPT 3 56022 BRACKET, WATER VALVE 4 0038 WASHER, LOCK /4 ZINC 2 5 0846 SCREW, CAP STSHW /4-20 X /2 2 6 0799 BARB ELBOW 90, 3/8HOSE X /4MPT (BRASS) 7 50069 CLAMP, HOSE, SAE #6, ADJ. TO 3/6 2 8 6508 HOSE, WATER 3/8 ID X 24 L 9 0982 TIE, CABLE, BLACK NYLON -/4 0 562 BARB ELBOW 90, 3/8HOSE X /8MPT (BRASS) 0864 NUT /8-27 PIPE THREAD (BRASS)
E-CPM8-PL-02 ILLUSTRATION 4: BRUSH SEAL GROUPING ITEM # 2 3 PART # 65036 0834 086 DESCRIPTION BRUSHES (SET OF 4), CPM-8 SCREW, CAP /4-20 X /2 ZINC NUT, KEPS LOCK /4-20 ZINC QTY. 8 8 00 Thomas Johnson Drive, Frederick, MD 2702-4600 USA Printed in USA Website: www.edcoinc.com Email: sales@edcoinc.com JWA 202 Page 9
E-CPM8-PL-02 ILLUSTRATION 5: DRUM, SHAFT & BEARING GROUPING
E-CPM8-PL-02 PARTS LISTING - ILLUSTRATIONS 5: DRUM, SHAFT & BEARING GROUPING 65050 DRUM ASSY. COMP. CPM-8 CUTTER (REFER TO ILLUS. 6 FOR BREAKDOWN) 2 65037 DRUM SHAFT 8-3/8 L, CPL/M-8 3 65039 NUT, JAM 5/8- LEFT-HAND THREAD 2 4 65038A DRIVER W/ BEARING ASSY., CPM-8 (INCLUDES ITEMS 5 THRU 9) 5 65056 096 BEARING ASSY. COMPLETE, -/4 DIA. FITTING, GREASE /4-28 X 90 (INCLUDED) 6 65038 DRIVER, CPM-8 7 03 SPACER, STEEL 9/6OD X 3/8ID X 7/32 3 8 0878 SCREW, SKT. HD. CAP 3/8-24 X ZINC 3 9 0873 RETAINING RING, EXT. -/4 0 65057 0808 BEARING ASSY. COMPLETE, "HEX BORE FITTING, GREASE /4-28 STR. (INCLUDED) 0025 WASHER, FLAT 3/8 SAE ZINC 8 2 08 WASHER, LOCK 3/8 ZINC 8 3 0309 SCREW, CAP 3/8-24 X -/4 ZINC 3
E-CPM8-PL-02 ILLUSTRATION 6: CUTTER DRUM ASSEMBLY STANDARD - 8 WIDTH * 65050 DRUM ASSEMBLY COMPLETE, CPM-8 CUTTER (INCLUDES ITEMS 2 THRU 6) 2 6505 DRUM ONLY, CUTTER, CPM-8 3 65054 RETAINING PLATE, CUTTER SHAFT 2 4 080 WASHER, LOCK 5/6 ZINC 6 5 0053 SCREW, CAP 5/6-8 X 3/4 6 6 2050 CP407 SHAFT /2 X 8-9/6 L 6 7* 2230 CG227 SPACER /2 ID 8* 2056 CUTTERS: CP206T 6-PT. CARBIDE -3/4 OD x 5/8 ID x /4 THK (SHOWN) SEE NOTE 20336 2206 CP207T 7-PT. SOLID CARBIDE MILLING -/2 OD x /2 ID x /2 THK JRS50P 8-PT. POINTED STEEL 2 OD x /2 ID x 3/6 THK 20206 CP305 2-PT. FLAT TIP STEEL 2 OD x 5/8 ID x 3/6 THK *NOTE: CUTTER WHEELS AND SPACERS ARE NOT INCLUDED WITH THE DRUM ASSEMBLY. THE NUMBER OF CUTTER WHEELS AND SPACERS VARY WITH TYPE OF SET-UP USED. REFER TO ASSEMBLY INSTRUCTIONS FOR SUGGESTED SET-UPS AND QUANTITIES. SEE NOTE
E-CPM8-PL-02 ILLUSTRATION 7: DIAMOND GROOVING HEAD ASSEMBLY OPTIONAL - 7 WIDTH 65077 HEAD ASSY., DIAMOND GROOVING, CPM-8 (INCLUDES ITEM 2 THRU 5) 2 65070 ARBOR, DIAMOND GROOVING HEAD,CPM-8 3 6507 ARBOR BLADE CAP 6, CPM-8 4 65075 WASHER, LOCK, INT. TOOTH -/4 5 65076 NUT, JAM /4-2 6* 65072 65073 65074 65078 7* 39808 39806 *NOTE: SPACER 6 OD X -/4ID X.063 (MINIMUM BLADE SPACING) 6 OD X -/4 ID X.43 (/2 C TO C BLADE SPACING) 6 OD X -/4 ID X.93 ( C TO C BLADE SPACING - SHOWN) 6 OD X -/4 ID X 5/8 (/6 C TO C BLADE SPACING) DIAM.BLADE DCC05S 7X.090X.25 W/ KW (3/32 THK. - SHOWN) DIAM.BLADE DCC05S 7X.250X.25 W/ KW (/4 THK.) DIAMOND BLADES AND SPACERS ARE NOT INCLUDED WITH THE HEAD ASSEMBLY. THESE QUANTITIES VARY WITH THE TYPE OF SET-UP USED. REFER TO SET-UP DRAWINGS FOR QUANTITIES. SEE NOTE SEE NOTE
E-CPM8-PL-02 ILLUSTRATION 8: EDGER ASSEMBLY OPTIONAL PART # 65027 65025 DRUM SHAFT, CPM-8 EDGER 2 0420 WASHER, LOCK /2 HEAVY-DUTY 3 0490 SCREW, SKT. HD. CAP /2-3 X 4 65026 FLANGE, DRIVER, CPM-8 EDGER 5 65028 PIN, WIRE LOCK 5/6 DIA. X 2.75 GRP 6 65039 NUT, JAM 5/8- LEFT-HAND THD. ZINC 2 7 65023A COVER ONLY, DRUM, CPM-8 EDGER 8 65024A COVER SIDE PANEL ONLY, CPM-8 EDGER 9 65029 BRUSHES (SET OF 3), CPM-8 EDGER -SET 0 028 RIVET, BLIND /8 X.250L X.262HD 4 034 RIVET, BLND 3/6X.450 L X.375HD DIA 8 2 6502 CAP/PLUG 2 RED PLASTIC, FLANGED 3 0055 SCREW, CAP 3/8-6 X 2 4 08 WASHER, LOCK 3/8 ZINC 2 5 0404 NUT, HEX 3/8-6 ZINC 2 6 0627 SCREW, SKT. BUTTON HD. 5/6-8 X3/4 2 7 080 WASHER, LOCK 5/6 ZINC 2 8 023 WASHER, FLAT 5/6 SAE ZINC 2
E-CPM8-PL-02 ILLUSTRATION 9: EDGER CUTTER DRUM ASSEMBLY OPTIONAL - 4 WIDTH * C66040 DRUM ASSEMBLY COMPLETE, CPM-8 CUTTER (INCLUDES ITEMS 2 THRU 6) 2 C6604 DRUM ONLY, CUTTER, CPM-4 3 65054 RETAINING PLATE, CUTTER SHAFT 2 4 080 WASHER, LOCK 5/6 ZINC 6 5 0627 SCREW, SKT. BUTTON HD. 5/6-8 X3/4 6 6 C66043 CP40 SHAFT /2 X 5-3/6 L 6 7* 2230 CG227 SPACER /2 ID 8* 2056 CUTTERS: CP206T 6-PT. CARBIDE -3/4 OD x 5/8 ID x /4 THK (SHOWN) SEE NOTE 20336 2206 CP207T 7-PT. SOLID CARBIDE MILLING -/2 OD x /2 ID x /2 THK JRS50P 8-PT. POINTED STEEL 2 OD x /2 ID x 3/6 THK 20206 CP305 2-PT. FLAT TIP STEEL 2 OD x 5/8 ID x 3/6 THK *NOTE: CUTTER WHEELS AND SPACERS ARE NOT INCLUDED WITH THE DRUM ASSEMBLY. THE NUMBER OF CUTTER WHEELS AND SPACERS VARY WITH TYPE OF SET-UP USED. REFER TO ASSEMBLY INSTRUCTIONS FOR SUGGESTED SET-UPS AND QUANTITIES. SEE NOTE
E-CPM8-PL-02 ILLUSTRATION 0: ENGINE GROUPING
E-CPM8-PL-02 PARTS LISTING - ILLUSTRATION 0: ENGINE GROUPING 5027 ENGINE, HONDA GX270U-QXC9 CYC.A.C. 2 0625 MUFFLER CAP, HONDA #833-ZE3-8 3 028 RIVET, BLIND /8 X.250L X.262HD 2 4 544 BARB, PUSH-ON 3/8 HOSE X /4FPT 5 566 HOSE, PUSH-ON 3/8 ID X 3 L 6 542 BARB, PUSH-ON 3/8HOSE X M2-.5MALE 7 0776 PIPE PLUG /4 NPT (BRASS) 8 098 BOLT, CARRIAGE 5/6-8 X -3/4 F.T. 4 9 023 0025 WASHER, FLAT 5/6 SAE ZINC WASHER, FLAT 3/8 SAE ZINC 4 2 0 080 WASHER, LOCK 5/6 ZINC 4 0054 NUT, HEX 5/6-8 ZINC 4 2 40388 CABLE, THROTTLE, LEVER-TYPE 24 3 0877 SCREW, CAP STSHW 0-24 X /2 2 4 083 WASHER, LOCK, INT. TOOTH #0 2 5 0982 TIE, CABLE, BLACK NYLON -/4 6 520A 50084 0877 083 SWITCH W/ WIRES, ROCKER RED ON-OFF ADDITIONAL PARTS REQ D. (NOT SHOWN): TERM., RING #0 6-4GA. INSULATED SCREW, CAP STSHW 0-24 X /2 WASHER, LOCK, INT. TOOTH #0 7 0553 SHEAVE 2.5 OD X 2GR.A X BORE 8 0307 KEY /4SQ X 2-/4 9 65045 SHEAVE 4.05 OD X 2GR.A X SH 20 0505 BUSHING, SHEAVE SH X -/4 BORE 2 4037 KEY /4SQ X -5/8 22 8007 BELT AX-33 2
E-CPM8-PL-02 ILLUSTRATION : SINGLE PHASE MOTOR GROUPING
PARTS LISTING - ILLUSTRATION : SINGLE PHASE MOTOR GROUPING 8026 62 664 6540 MOTOR, BALDOR 5HP-PH 60HZ 3450RPM REPLACEMENT PARTS: CAPACITOR, START, BALDOR EC6C06SP CAPACITOR, RUN, BALDOR #OC3040F09SP THERMAL PROT. (RESET BUTTON) TPBRT25DB 2 2 ----- KEY /4 SQ. X -3/4 (INCLUDED W/ MOTOR) 3 77043 SWITCH, ROTARY CAM ON/OFF 4 77042 BRACKET, ROTARY CAM SWITCH 5 0846 SCREW, CAP STSHW /4-20 X /2 2 6 0038 WASHER, LOCK /4 ZINC 2 7 663 SCREW, MACHINE 8-32 X /2 4 (LOCATED INSIDE OF SWITCH BOX) 8 0462 NUT, KEPS LOCK 8-32 ZINC 4 9 77043- SWITCH ADAPTER, PG6 TO /2 NPT 2 0 430 STRAIN RELIEF /2NPT X.550-.650 2 6537 WIRE HARNESS 0/3 X 60 LOA 2 86026 WIRE HARNESS 0/3 X 24 LOA 3 40037 PLUG, LOCKING 20A/250V L6-20P 4 40000 CONNECTOR, LOCKING 20A/250V L6-20C 5 0982 TIE, CABLE, BLACK NYLON -/4 6 565 CLAMP, LOOM, 5/8 (SAE SIZE 0) 2 7 0877 083 SCREW, CAP STSHW 0-24 X /2 WASHER, LOCK, INT. TOOTH #0 8 6539 STRAIN RELIEF 90D X 3/4NPT.50-.625 9 0740 CONDUIT LOCK NUT 3/4 NP (LOCATED INSIDE OF JUNCTION BOX) 20 089 BOLT, CARRIAGE 5/6-8 X FULL THD 4 2 023 WASHER, FLAT 5/6 SAE ZINC 4 22 080 WASHER, LOCK 5/6 ZINC 4 23 0054 NUT, HEX 5/6-8 ZINC 4 24 0555 SHEAVE 2.5 OD X 2GR.A X -/8 BORE 25 65045 SHEAVE 4.05 OD X 2GR.A X SH 26 0505 BUSHING, SHEAVE SH X -/4 BORE 27 4037 KEY /4SQ X -5/8 28 0239 BELT A32 2 29 5204 PLUG, RECT. HOLE, PLASTIC SNAP-IN E-CPM8-PL-02 2 2
E-CPM8-PL-02 ILLUSTRATION 2: THREE PHASE MOTOR GROUPING PARTS LISTING - ILLUSTRATION 2: THREE PHASE MOTOR GROUPING 8022 6020 MOTOR, BALDOR 5HP-3PH-60HZ-230/460V EM363T MOTOR, BALDOR 5HP-3PH 50HZ-220/380/440V M363T-50 2 ----- KEY /4 SQ X -3/4 (INCLUDED W/ MOTOR) 3 6660 SWITCH BOX COMPLETE, ON/OFF/E-STOP... INCLUDES: 666 ENCLOSURE, 2 HOLE ACI PBE2 6662 LEGEND PLATE, EMER.STOP - BLACK 6663 LEGEND PLATE, OFF/ON 6664 6665 MUSHROOM BUTTON, RED JR22GNR
PARTS LISTING CONTINUED - ILLUS. 2: THREE PHASE MOTOR GROUPING 4 65088 BRACKET, REMOTE SWITCH, CPM-8 5 663 SCREW, MACHINE 8-32 X /2 4 6 0462 NUT, KEPS LOCK 8-32 ZINC 4 7 0846 SCREW, CAP STSHW /4-20 X /2 4 8 0038 WASHER, LOCK /4 ZINC 4 9 0790 CONDUIT LOCK NUT /2 NP (LOCATED INSIDE BOX) 0 690 STRAIN RELIEF /2NPT X.250-.350 2 6540 WIRE HARNESS 6/2 X 48 LOA 2 0982 TIE, CABLE, BLACK NYLON -/4 3 3 6457 6458 6476 667 668 6622 6623 6632 6633 6635 STARTER ACI #28844 200/240V COIL.3-6A O/L STARTER ACI #28846 440/480V COIL 5.5-7.5A O/L STARTER ACI 440/480V 7.2-0A O/L (USED FOR 50Hz-380V) REPLACEMENT PARTS: STARTER CONT./COIL ACI SK8.30-230 STARTER CONT./COIL ACI SK8.30-460 STARTER AC COIL 200/240V-60HZ, 90/220-50HZ STARTER AC COIL 440/480V-60HZ, 380/45-50HZ STARTER OVERLOAD RELAY 5.5-7.5 AMP STARTER OVERLOAD RELAY 7.2-0.0 AMP STARTER OVERLOAD RELAY.3-6.0 AMP 4 4053 STRAIN RELIEF /2NPT X.625-.750 5 6505 WIRE HARNESS 0/4 X 48 LOA, CPM-8 6 565 CLAMP, LOOM, 5/8 (SAE SIZE 0) 7 083 WASHER, LOCK, INT. TOOTH #0 8 0877 SCREW, CAP STSHW 0-24 X /2 9 62 STRAIN RELIEF /2 90D X.625-.750 20 6539 STRAIN RELIEF 90D X 3/4NPT.50-.625 2 0740 CONDUIT LOCK NUT 3/4 NP (LOCATED INSIDE BOX) 22 6508 WIRE HARNESS 0/4 X 32 LOA, CPM-8 23 65087 MOUNT, STARTER 24 732 0384 SCREW, MACHINE 0-32 X -3/4 RPH SCREW, MACHINE 0-32 X RHP 25 0832 NUT, KEPS LOCK 0-32 ZINC 3 26 0820 BOLT, CARRIAGE 5/6-8 X -/4 F.T. 4 27 023 WASHER, FLAT 5/6 SAE ZINC 4 28 080 WASHER, LOCK 5/6 ZINC 4 29 0054 NUT, HEX 5/6-8 ZINC 4 30 0555 0526 SHEAVE 2.5 OD X 2GR.A X -/8 BORE (60Hz MOTOR) SHEAVE 3 OD X 2GR.A X -/8 BORE (50Hz MOTOR) 3 65045 SHEAVE 4.05 OD X 2GR.A X SH 32 0505 BUSHING, SHEAVE SH X -/4 BORE 33 4037 KEY /4SQ X -5/8 34 0239 BELT A32 2 35 5204 PLUG, RECT. HOLE, PLASTIC SNAP-IN E-CPM8-PL-02 2