Table of Contents Available Steel Poles...Page 1 Available Aluminum Poles...Page 2 Pole Top Preparations for Steel & Aluminum...Page 3 -on rackets...page 4 Tenon Mount rackets...page 6 Accessories...Page 7 ixture Specific rackets...page 8 Internal Slip itter/hand-hole Covers/Pole Caps...Page 9 Steel Pole ase Covers...Page 10 Available Pole ase Covers... Page 11 Steel Pole Anchor s...page 12 Steel Pole EPAs/Wall Mount rackets...page 13 Aluminum Pole EPAs...Page 14 Aluminum Pole EPAs...Page 15 Wind Speed Map...Page 16
Available Steel Poles STEE ROUND POES (RP) STEE SQUARE POES (SQ) STEE ROUND TAPERED POES (RTP) Steel Pole Shaft Preparations (Optional) OS Occupancy Sensor Preparation (Optional) Available on all Above Poles 3" (76mm) 3" (76mm) or use with PMOS Occupancy Sensor 6" (152mm) 6" (152mm) HAND-HOE Square Poles Round and Round Tapered Poles OPTIONA ASE COVER Steel Pole Shaft Preparations (Optional) lood ight Preparation (Optional) Available on all Above Poles or use with O rackets PROJECTION 12" (305mm) STANDARD Square Poles Round and Round Tapered Poles ROUND EVE (4) ANCHOR OTS OUNDATION Y OTHERS SI Industries Inc. 3305 1
Available Aluminum Poles AUMINUM ROUND POES (RP) AUMINUM SQUARE (SOT CORNER) POES (SQ) AUMINUM ROUND TAPERED POES (RTP) AUMINUM UTED ROUND POES (RN) AUMINUM ROUND HINED ASE POES (RHP) Aluminum Round Aluminum Square (Soft Corner) Aluminum Round Tapered 8'-20' (2.4m - 6.1m) 8'-35' (2.4m - 10.7m) 18'-30' (5.5m - 9.1m) Hand-hole Hand-hole Hand Hole Heights = 12" (305mm) Standard Nut Covers 12" (305mm) Standard Nut Cover Discs = 14" (356mm) Standard 6" (152mm) = 18" (457mm) Standard Hand-hole Nut Covers 12 (305mm) for 5 Pole ottom 18"(457mm) for 6, 8 or 9 Pole ottom Aluminum Round Hinged ase 8'-20' (2.4m - 6.1m) Shipped standard without Hand-hole. Optional Hand-hole available. Aluminum luted Round with Decorative ase RN2 RN3 RN2, RN3 N = 2-3/8" (60mm) O.D. x Tall Tenon 4N = O.D. x Tall Tenon 8'-18' (2.4m - 5.5m) Cross Section 16 lat lute Round Hinged ase 21-1/2 (546mm) 31-1/2 (800mm) Nut Covers Aluminum 2-Piece Cast ase Cover (Standard) 17 Dia. (432mm) 17 Dia. (432mm) RN2 Access Door 4" wide x 5-5/8" tall (102mm x 143mm) RN3 Access Door 3-1/4" wide x 16-1/2" tall (83mm x 419mm) Aluminum Pole Shaft Preparation (Optional) Not available on fluted poles estoon preparation for P & P options SI Industries Inc. 3305 2
Pole Top Preparations for Steel & Aluminum -on Drilling Pattern 5 (127mm) Traditional Drilling Pattern 4RP5 5RP5 4SQ5 5SQ5 6SQ5 RTP5 4RHP5 5RHP5 2-1/2 (64mm) 4-5/8 (117mm) 1-1/2 (38mm) 9/16 DIA. HOES (TYP. 2 PCS.) 3/4 DIA. HOE 3 (76mm) Reduced Drilling Pattern 4RP3 5RP3 4SQ3 5SQ3 4RHP3 5RHP3 2X 9/16-7/8 SOT 1-1/16 (27mm) 2-1/8 (54mm) 3-1/2 (89mm) Ø 5/8 Tenon Mount 4RPN 5RPN 4SQN 5SQN 6SQN RTPN 4RHPN 5RHPN 4RN2 4RN3 5RN2 5RN3 6RN2 6RN3 Steel Poles N = 2-3/8 O.D. (60mm) X 4-3/4 tall (121mm) Aluminum Poles N = 2-3/8 O.D. (60mm) X 4 tall (102mm) 5RPN 5RHPN 4RN2 4RN3 5RN2 5RN3 6RN2 6RN3 Steel Poles 4N = 4 O.D. (102mm) X 4-7/8 tall (124mm) Aluminum Poles 4N = 4 O.D. (102mm) X 5 tall (127mm) No Drilling with Pole Cap 4RPI 5RPI 4SQI 5SQI 4RHPI 5RHPI RPI - or use with ifestyle UCS and UC D180 rackets SQI - or use with internal Slip-fitter racket No Drilling without Pole Cap 4RPS 4RHPS or use with ifestyle Classic Hook (CH) mounting and Constitution, Enterprise, and exington Post Top (PT) single mounting styles SI Industries Inc. 3305 3
-on rackets SQ5, RP5, RTP5, RHP5 - or Use with 5 (127mm) Traditional Drill Pattern 2-1/2" x 5-3/8" x 6" (64mm) x (127mm) x152mm) 2-1/2" x 5-3/8" x 8" (64mm) x (127mm) x152mm) 2-1/2" x 5-3/8" x 12" (64mm) x (127mm) x152mm) 2-1/2" x 5-3/8" x 6" (64mm) x (127mm) x152mm) KA O S (6, 8, or 12) CR R Aluminum Mounting Arm Not for use with XS, Patriot, Hilton or XC. (Round pole applications use RPP2) 6" Part # 16196601CR 8" Part # 16196604CR 12" Part # 16196602CR KA HRO S 6 CR Aluminum Mounting Arm Use with Hilton II on round poles Part # 168414CR 6" (152mm) KA O EC 6 CR Aluminum extension bracket- Use with Patriot. Part # 142862CR (Round pole applications require RPPC) 6" (152mm) KA O ADJ 6 CR - Adjustable racket Aluminum traditional drill pattern (both sides)- Standard arm is not used. Cannot be used with top-access fixtures, Patriot, XS or XC. or use with square pole only. Part # 130526CR KS O PA 40 CR - Parallel Arm 1 piece steel traditional drill pattern designed for direct mounting of fixture to face of bracket. Standard arms are not required except for Hilton Series. Part # 141028CR KU O S 19 CR - Upsweep Arm 3 piece aluminum traditional drill pattern- Compatible with Patriot. Part # 144191CR RPP2 K - Round Pole Plate Part # 162914K RPPC CR - Round Pole Plate or Patriot Part # 141940CR KA O RA 8 CR - Radius Arm or Challenger Medium, Patriot, and all square and rectangular fixtures. Not for use with XS or XC. Part # 169010 CR SQ3, RP3, RHP3 - or Use with 3 (76mm) Reduced Drill Pattern KA-XO-EC-6-CR EXTENSION ARM - Aluminum 3" reduced drill pattern. Use this 6" extension arm to position the fixture further from the pole. Not for use with Mirada Series or decorative area ligts. Part #382136CR X4RPP CR - Round Pole Plate or 4" Round Poles Part # 379967CR X5RPP CR - Round Pole Plate or 5" Round Poles Part # 379968CR Drilling ocations Side D Side C Side A (Hand-hole Side) Side Note: Consult factory for custom variations. Standard S and D pole preparations are located 3/4 of the height of the pole from the base, unless otherwise specified. (Except on 20' Round Tapered pole -Maximum height for S & D is 13' from base.) Sides A C D X Hand-hole Single X D180 X X D90 X X T90 X X X TN120 * X Q90 X X X X Single O(S) X Double O(D) X X *Other two locations will be 120 to the left and right of Side A. ixture Configurations Single D90 DN90 D180 Parallel T90 TN120 QN90 Q90 SI Industries Inc. 3305 4
-on rackets Retrofit -On rackets Use to convert poles with existing 5 (127mm) Traditional 2-hole, 3-hole and 4-hole SI drilling patterns to use with fixtures with 3 (76mm) reduced drill pattern. KS-XO-ADP-2H-CR - To convert 2-hole 5 traditional SI drilling pattern on round or square poles. Part Number 388239CR 5-9/16 x 2-5/8 (141mm x 67mm) KS-XO-ADP-2H-CR-EC6 - To convert 2-hole 5 traditional SI drilling pattern. Includes 6" extension arm and proper hardware for use with round or square poles. Part Number 388241CR Mounting racket w/ec6 Arm KS-XO-ADP-3H-CR - To convert 3-hole SI drilling pattern on square poles. Part Number 388059CR 4-1/2 x 3-3/4 (114mm x 95mm) KS-XO-ADP-4H-CR - To convert 4-hole SI drilling pattern on square poles. Part Number 388060CR 4-3/4 x 3-3/4 (121mm x 95mm) When ordering adaptors for 3- and 4-hole drilled square poles, ordering a replacement cap is also recommended due to the aging of the existing plastic pole cap. lood rackets - or use with S & D pole shaft preparations 4-3/4" (121mm) KS O 5 * CR Part # 107054CR 18-7/8" (479mm) KS O 18 * CR Part # 107053CR 30" (762mm) KS O 30 CR Part # 133163CR Mounting Hole Plugs & Decal ront Side Mounting Hole Plugs Set of 3 for square pole with 5 traditional drill pattern. Part # 132336 Mounting Hole Decal (MHD) Available for round & round tapered poles and square poles with 3 reduced drilling pattern. Part # 340120 SI Industries Inc. 3305 5
Tenon Mount rackets SQN, RPN, RN, RHPN, RTPN with N Tenon (2 3/8 (60mm) O.D. x 4 3/4 (121mm) or 4 (102mm) tall) Tenon Mount itters with 5 (127mm) Traditional Drill Pattern Tenon Mount itters with 3 (76mm) Reduced Drill Pattern Single/D-180 (Drilled 2 Sides) 10-3/4 (273mm) 11 D90/T90/Q90 (279mm) (Drilled 4 Sides) 10-3/4 (273mm) KA NM * CR or flat surface brackets. Single/D180 - Part # 43549CR D90/Q90/T90 - Part # 43548CR KA RNM TN120 * CR Drilled 3 sides at 120. or radius surface brackets. Part # 107023CR Tenon Mount Adjustable with 5 (127mm) Traditional Drill Pattern Thru bolt 9-3/4" (248mm) KA NM ADJ * CR Aluminum round slipfitter for 2-3/8" (60mm) O.D. or 2-7/8" (73mm) O.D. tenon - should not be used with standard arm. Cannot be used with top-access fixtures,xc, XS, Patriot, or Hilton Series. Part # - 130527CR lood rackets - Used with tenon mount poles 17" (432mm) 2" (51mm) PIPE 17" (432mm) KS-PT-2-CR Part# 107066CR 2" (51mm) 17" (432mm) KA XNM-S or D180- * CR Single/D-180 (Drilled 2 Sides) Tenon Mount Parallel Arm with 5 (127mm) Traditional Drill Pattern 2" (51mm) x 8" (203mm) x 40" (1016mm) Tenon Adaptor KS NM PA 40 CR One piece steel arm, round slipfitter for 2 3/8" (60mm) O.D. tenon. Designed for direct mounting of fixtures to face of bracket. Standard arm is not required, except for Hilton Series. Part # - 143888CR KS-PT-3-30-CR Part# 133505CR KA XNM-D90, T90 or Q90- * CR D90/T90/Q90 (Drilled 4 Sides) 17" (432mm) 30" (762mm) 17" 17" (432mm) (432mm) KS-PT-3-CR PIPE Part# 107070CR 2" (51mm) PIPE 30" (762mm) Consult factory for part numbers 2" (51mm) PIPE KS-PT-4-CR Part# 123109CR 48" 30" (1219mm) 24" (762mm) (610mm) KS-PT-12-CR Part# 137105CR KS-PT-13-3-CR Part# 137107CR KS-PT-14-CR Part# 137108CR Tenon Mount Mast Arm 10 (254 mm) 4, 6, 8 Nominal 8,12, 16 Nominal 10 (254 mm) 32 (813 mm) Single D 180 Mast Arm Adaptor with 5 (127mm) Traditional Drill Pattern KA PT Mast Arm 4 S CR KA PT Mast Arm 4 D180 CR KA PT Mast Arm 6 S CR KA PT Mast Arm 6 D180 CR KA PT Mast Arm 8 S CR KA PT Mast Arm 8 D180 CR KA NM MA 5 CR Mast Arm Adaptor or use with existing mast arm by others. Cannot be used with XS, Hilton Series. Slipfits 2 pipe [2-3/8 (60mm) O.D.] Part # 168778CR Part# 409570CR 409571CR 409572CR 409573CR 409574CR 409575CR SI Mast Arm: Available in 4, 6 and 8 nominal arm lengths with single (S) and double arms at 180º (D180) mounting configurations. All arms have a 32 rise. KA NM MA 5 XC CR Mast Arm Adaptor or use XC Part # 617865CR SI Industries Inc. 3305 6
Tenon Reducers NM-RD Steel round slipfitter reducer, comes with set screws and one through bolt. Accessories P/N Description I.D. O.D. its How Much Play 137096CR KS-NM-RD-2.5-CR 3.068" 3.5" 2.875" O.D. 2-5/8" to 2-7/8" 137093CR KS-NM-RD-3.0-CR 3.640" 4.0" 3.5" O.D. 3-1/4" to 3-1/2" 137090CR KS-NM-RD-3.5-CR 4.140" 4.5" 4.0" O.D. 3-3/4" to 4" NOTES: Part description refers to pipe size. Top tenon is 2 pipe or 2-3/8" (60mm) dia. x 4-3/4" (121mm) high. How Much Play = or the in between sizes of their tenon, you have about 1/4" (6mm) play. its = Customer's existing tenon size. anner rackets for use with Straight Round Poles 1.50 Ø (38mm) 18 (457mm), 24 610mm), or 30 (762mm) Single Side Double racket Assembly KS 4R S 18, 24, 30 CR Consult factory for part numbers KS 5R S 18, 24, 30 CR Consult factory for part numbers D180 Double racket Assembly KS 4R D 18, 24, 30 CR Consult factory for part numbers KS 5R D 18, 24, 30 CR Consult factory for part numbers SITE SPECIIC 4.00 Ø (102mm) or 5.00 Ø (127mm) O.D. Pole Special EPA calculations are required on banner bracket applications, consult factory. Vibration Damper for use with Steel Square Poles - -on Mount 4 (102mm) and 5 (127mm) square pole dampers supplied with (2) 15 (4.6M) vinyl coated chains 6 (152mm) square pole dampers supplied with (2) 20 (6.1M) vinyl coated chains Poles vibration dampers are designed to reduce the amounts of vibration incurred in certain poles. They are not intended to eliminate vibration altogether. Kit VIR DMPR 4SQ Pole Part # 172539 Kit VIR DMPR 5SQ Pole Part # 172538 Kit VIR DMPR 6SQ Pole Part # 178361 SI Industries Inc. 3305 7
ixture Specific rackets rackets for use with SI Practica Small (PCS) Improper use of brackets will void warranty KS-XO-WM-*-CR 2-bolt pattern steel wall mount plate to use with 3 (76mm) reduced drill pattern. Part # 382132CR If KA-XNM-PCS-ADJ is required for wall mount application, KS-O-WM-W/KS-O-5-CR bracket is required KS-O-WM-W/KS-O-5-CR 2-bolt pattern steel wall mount plate and OE bracket with KAXNM-PCS-ADJ bracket for use with PCS only. Part # 628675CR KA-XNM-PCS-ADJ-*-CR Tenon slipfitter bracket titable up to 90º. its 2 pipe (2 3/8 O.D.) tenon. Part # 626315CR Not compatible with XCS, XCM, XC. SP-PCS-KS-NM-4IS-*-CR Part # 630804CR SP-PCS-KS-NM-5IS-*-CR Part # 630808CR racket adapts open topped 4 (102mm) or 5 (127mm) square pole to have a 2 pipe (2 3/8 O.D.) tenon. rackets for use with XCS, XCM & PCS only Pole Quick Mounts with Universal Mounting Plate for one person installation. Can mount to SI s and most competitor's drilling patterns. or use with square poles & KA NM tenon adaptors only. 15 Angle PQM15 Allows 15 uptilt of fixture for greater throw of light with increased vertical illumination Horizontal - PQMH 15 o Note: When mounting to a non-si drilling pattern, the original nut plate must be retained for use with bracket. PQMH-KIT-CR Square Pole Quick Mount Horizontal racket 582328CR PQM15-KIT-CR Square Pole Quick Mount racket w/fixed 15º Angle 582329CR Adjustable rackets for use with XRSU, XRMU and PRSU Roadway ixtures 10-5/16" (262mm) 10-1/16" (256mm) -On KA-O-XRSU/XRMU/PRSU-ADJ-CR for poles with 5 traditional drill pattern Part # 530070CR 8-15/16" (227mm) 13-11/16" (348mm) Tenon Mount KA-NM-XRSU/XRMU/PRSU-ADJ-CR for poles with 2 pipe - 2 3/8 (60mm) O.D. Part # 527793CR SI Industries Inc. 3305 8
Internal Slip itter/hand-hole Covers/Pole Caps SQI (no drilling) Internal Slip itter racket U.S. Patent # 5,599,094 KA (4IS, 5IS) (Q90, D180) CR for 5 (127mm) traditional drill pattern KA (X4IS, X5IS) (D90, D180) CR for 3 (76mm) reduced drill pattern Utilize to retrofit existing & square poles. Use with & SQI poles with wall thickness of 11 ga. (0.120) or 7 ga. (0.180). D180 slipfitters come with (1) set of plugs Q90 slipfitters come with (2) sets of plugs * Do not use on round tapered or round poles Use with 5 traditional drill pattern fixtures KA 4IS D180 * CR PART# 122625CR KA 4IS Q90 * CR PART# 122626CR KA 5IS D180 * CR PART# 122627CR KA 5IS Q90 * CR PART# 122628CR racket cap Hole plugs Positioning rings in lowest threads Use with 3 traditional drill pattern fixtures KA X4IS D180 * CR PART# 415635CR KA X4IS Q90 * CR PART# 440949CR KA X5IS D180 * CR PART# 417508CR KA X5IS Q90 * CR PART# 443447CR Top View 3 1/4" (83mm) Positioning Rings Hand-Hole Cover Kits with asket and 2 Screws - Steel Poles Only 6-1/4" (159mm) 6-1/4" (159mm) 6-1/4" (159mm) 6-1/4" (159mm) 3-1/4" (83mm) Part #349593CR Used on all square steel poles and all round steel poles 18'-0" (5.5M) and above except Round Tapered Steel. 4-1/4" (108mm) Part #547618CR Used on all Round Tapered Steel Poles. 3-1/4" (83mm) Part #53306CR Used on all ER2 & I options for all Square Steel Poles, and all Round Steel Poles 18'-0" (5.5M) and above except Round Tapered Steel. No receptacle. 4-1/4" (108mm) Part #53928CR Used on all ER2 & I options for Round Tapered Steel Poles. No receptacle. 6" (152mm) 7" (178mm) 5" (127mm) 5 3/4" (148mm) 3 1/2" (89mm) Part #141062CR Used on all & Round Steel Poles under 18'-0" (5.5M) Consult factory for aluminum pole hand-hole and I covers 3 1/2" (89mm) Part #5707502CR Used on all ER2 & I options for & Round Steel Poles under 18'-0" (5.5M). No receptacle. 2 1/2" (64mm) 3" (76mm) Part #179079 In use cover. Used on all ER2 & I options Pole Caps - Steel Poles Only ROUND TAPERED 3" 20/25 ft. Part #54018 3-1/4" 30/50 ft. Part #54019 3-1/2" 35/39 ft. Part #54020 4 45 ft. Part #54015 ROUND 4" Part #54015 5" Part #54016 SQUARE 4" Part #54008 5" Part #540090 6" Part #54010 OT-ON TN120 for square pole 4" Part #132029CR 5" Part #132030CR TENON ITTER (KA RNM) Part #53460CR Consult factory for aluminum pole caps SI Industries Inc. 3305 9
Steel Pole ase Covers ase Covers - Steel Poles - Square shaped base covers are.50 or.63 aluminum 11.318" - 12.313" (287mm - 313mm) Square 11.318" (287mm) Square 11.318" - 14.5" (368mm) (287mm - 368mm) Square Square Steel Poles 4"(102mm) C 11.318" (287mm) sq. x 4.3" (109mm) tall with 4.125" (105mm) sq. opening Part #122559CR 5"(127mm) C 11.318" (287mm) sq. x 4.8" (122mm) tall with 5.125" (130mm) sq. opening Part #122561CR 6"(152mm) C 12.313" (313mm) sq. x tall with 6.125" (156mm) sq. opening Part #122563CR Round Steel Poles 4"(102mm) SRC 4.3" (109mm) tall with 4.25" (108mm) dia. opening Part #158450CR SRC 4.8" (122mm) tall with 5.25" (133mm) dia. opening Part #158451CR 15" (381mm) 9.75 (248mm) C 4 5 Decorative two-piece die cast construction fits 4 (102mm)and 5 (127mm) diameter straight round poles. Includes 4 (102mm) round pole adaptor molded from black silicone rubber Part #483859 CR Round Tapered Steel Poles 20' (6.1M) SRT 11.318" (287mm) sq. x 4.8" (122mm) tall with 6.15" (156mm) dia. opening Part #158388CR 25' (7.6M) SRTC 11.318" (287mm) sq. x 4.8" (122mm) tall with 6.85" (174mm) dia. opening Part #158390CR 30' (9.1M) SRTC 11.318" (287mm) sq. x 4.8" (122mm) tall with 7.75" (174mm) dia. opening Part #158392CR 35' (10.7M) SRTC 13" (330mm) sq. x 4.875" (124mm) tall with 8.75" (222mm) dia. opening Part #158554CR 39' (11.9M) SRTC (7 & 11 age) 12.875" (327mm) sq. x 5.5" (140mm) tall with 9.125" (232mm) dia. opening Part #155887CR 45' (13.7M) SRTC 14.5" (368mm) sq. x 5.875" (149mm) tall with 10.25" (260mm) dia. opening Part #158571CR 50' (15.2M) SRTC 14.5" (368mm) sq. x 5.875" (149mm) tall with 10.25" (260mm) dia. opening Part #158578CR SI Industries Inc. 3305 10
Available Pole ase Covers ase Covers - Aluminum Poles Square Aluminum Pole Square Two-Piece Cast ase Cover (Optional) Round Aluminum Pole One-Piece Spun Aluminum Collar (Optional) 4DAC - 4" Square Cast 2-Piece ase Cove 13 (330mm) square x 6.31 (160mm) tall Part # 505605CR 5DAC - 5" Square Cast 2-Piece ase Cove 13 (330mm) square x 6.31 (160mm) tall Part # 505606CR 4RSAC - 4" Round 1-Piece Spun Aluminum Collar 11.875 (302mm) dia. x 5.5 (140mm) tall with 4.125 (105mm) opening Part # 506859CR 5RSAC - 5" Round 1-Piece Spun Aluminum Collar 10.75 (273mm) dia. x 5.5 (140mm) tall with 5.125 (130mm) dia. opening Part # 506860CR 6DAC - 6" Square Cast 2-Piece ase Cove 14.5 (368mm) square x 7.25 (184mm) tall Part # 505608CR 15" (381mm) 9.75 (248mm) C 4 5 Decorative two-piece die cast construction fits 4 (102mm)and 5 (127mm) diameter straight round poles. Includes 4 (102mm) round pole adapter molded from black silicone rubber Part #483859 CR Round Tapered Aluminum Pole One-Piece Spun Aluminum Collar (Optional) Round Hinged ase Aluminum Pole ase cover ships with pole as a standard Aluminum 2-Piece Cast ase Cover (Standard) 5RSAC - Round 1-Piece Spun Auminum Collar for RTP w/5 bottom 10.75 (273mm) dia. x 5.5 (140mm) tall with 5.125 (130mm) dia. opening Part # 505647CR 6RSAC - Round 1-Piece Spun Auminum Collar for RTP w/6 bottom 14 (356mm) dia. x 5.5 (140mm) tall with 6.125 (156mm) dia. opening Part # 505648CR 8RSAC - Round 1-Piece Spun Auminum Collar for RTP w/8 bottom 17.125 (435mm) dia. x 5.5 (140mm) tall with 8.125 (206mm) dia. opening Part # 505649CR Round 2-Piece Cast ase Cover for 4 (102mm) and 5 (127mm) Round Hinged ase Aluminum Pole 15 (381mm) dia. x 6 (152mm) tall 4RHDAC Part # Consult actory 5RHDAC Part # Consult actory SI Industries Inc. 3305 11
3/8" X 10" (10mm X 254mm) alvanized Steel 1" (25mm) 10" (254mm) 2" (51mm) Min 3/8" (10mm) Steel Pole Anchor s Used with: A kit# 285560 ollards 4 1/2" (114mm) OT CIRCE. Each anchor bolt furnished with: (2) 3/8" (10mm)-16 galvanized hex nuts and (2) U.S.S. 3/8" (10mm) flat washers 7/16" (11mm) I.D. x 1" (25mm) O.D. x 0.1" (3mm) thick galvanized 3/4" X 30" Steel / 3/4" X 30" (19mm X 762mm) alvanized (Partially) 3" (76mm) 30" (762mm) 3 1/ 2" (89mm) Min Each anchor bolt furnished with: (2) 3/4" (19mm)-10 zinc plated or galvanized hex nuts and (2) U.S.S. 3/4" (19mm) flat washers (13/16" (17mm) I.D. x 2" (51mm) O.D. x 5/32" (4mm) thick) zinc plated or galvanized 3/4" (19mm) Steel used with: A kit# 122584 4SQ ST / 11" (279mm) OT CIRCE A kit# 122582 4RP ST S10 11" (279mm) OT CIRCE A kit# 1225850 5SQ ST 11" (279mm) OT CIRCE A kit# 135460 5RP ST 11" (279mm) OT CIRCE alvanized used with: A kit# 122609 4SQ ST A / 11" (279mm) OT CIRCE A kit# 122607 4RP ST A S10 11" (279mm) OT CIRCE A kit# 122610 5SQ ST. A 11" (279mm) OT CIRCE A kit# 135461 5RP ST A 11" (279mm) OT CIRCE 1" X 36" (25mm X 914mm) Steel / 1" X 36" (25mm X 914mm) alvanized (Partially) 3 1/2" (89mm) 36" (914mm) 4 1/4" (108mm) Min. 1" (25mm) Steel used with: A kit# 122586 5SQ. ST 11" (279mm) OT CIRCE A kit# 122583 5RP ST 11" (279mm) OT CIRCE A kit# 122587 6SQ ST 12" (305mm) OT CIRCE A kit# 122588 RTP ST 20/25/30' 11" (279mm) OT CIRCE A kit# 122589 RTP ST 35/39' 12" (305mm) OT CIRCE alvanized used with: A kit# 122611 5SQ ST. A 11" (279mm) OT CIRCE A kit# 122608 5RP ST A 11" (279mm) OT CIRCE A kit# 122612 6SQ ST A 12" (305mm) OT CIRCE A kit# 122613 RTP ST A 20/25/30' 11" (279mm) OT CIRCE A kit# 1226140 RTP ST A 35/39' 12" (305mm) OT CIRCE Each anchor bolt furnished with: (2) 1" (25mm)-8 zinc plated or galvanized hex nuts and (2) U.S.S. 1" (25mm) flat washers - 1 1/16" (29mm) I.D. x 2 1/2" (64mm) O.D. x 11/64" (4mm) thick - zinc plated or galvanized 1-1/4" X 42" (32mm X 1067mm) alvanized (Partially) 6" (152mm) 42" (1067mm) 6" (152mm) Min. alvanized only available. Used with: A kit# 122615 RTP ST. A 39' (11.9mm) 12" (305mm) A kit# 122616 RTP ST A 14" (356mm) Each anchor bolt furnished with: (2) 1 1/4" (32mm)-7 galvanized hex nuts and (2) U.S.S. 1 1/4" (32mm) flat washers (1 3/8" (35mm) I.D. x 3" (76mm) O.D. x.165" (4mm) thick) galvanized 1 1/4" (32mm) Consult factory for aluminum pole anchor bolts Anchor Conversion Table "A" = "" Square 3.19" (81mm) 4.50" (114mm) 4.50" (114mm) 6.36" (162mm) 5.00" (127mm) 7.00" (178mm) 5.66" (144mm) 8.00" (203mm) 6.50" (165mm) 9.19" (233mm) 6.75" (171mm) 9.50" (241mm) 7.75" (197mm) 11.00" (279mm) 8.12" (206mm) 11.50" (292mm) 8.50" (216mm) 12.00" (305mm) 8.84" (225mm) 12.50" (318mm) 9.19" (233mm) 13.00" (330mm) 9.90" (251mm) 14.00" (356mm) 10.25" (260mm) 14.50" (368mm) 12.00" (305mm) 17.00" (432mm) A Square SI Industries Inc. 3305 12
Steel Pole EPAs/Wall Mount rackets Pole EPAs Steel Square Poles Height 14' (4.3m) 16' (4.9m) 16' (4.9m) 18' (5.5m) 18' (5.5m) 22' (6.7m) 22' (6.7m) 22' (6.7m) 22' (6.7m) 24' (7.3m) 24' (7.3m) 24' (7.3m) 24' (7.3m) 24' (7.3m) 26' (7.9m) 26' (7.9m) 26' (7.9m) 26' (7.9m) 26' (7.9m) 28' (8.5m) 28' (8.5m) 30' (9.1m) 30' (9.1m) 35' (10.7m) 39' (11.9m) Height 25' (7.6m) 30' (9.1m) 35' (10.7m) 39' (11.9m) 39' (11.9m) 45'* (13.7m) 50'* (15.2m) EPA 70 MPH 80 MPH 90 MPH MPH 23.3 18.6 34.6 14.4 27.9 11.0 18.7 22.5 35.5 10.4 18.7 20.8 34.0 7.7 15.1 16.7 28.6 46.2 5.3 12.0 13.2 24.0 39.6 19.9 33.9 16.3 28.8 18.3 11.5 16.7 13.1 25.0 9.7 19.7 7.0 12.8 15.4 25.4 6.3 12.6 13.8 23.9 4.0 9.7 10.5 19.6 32.6 2.1 7.2 7.6 15.8 27.3 12.5 22.7 9.6 18.6 10.0 4.3 12.2 9.3 18.5 6.5 14.1 4.2 8.8 10.5 18.4 3.4 8.4 8.9 17.0 1.5 6.0 6.2 13.4 23.2 3.9 3.8 10.3 18.9 7.5 15.1 5.0 11.6 4.3 Steel Round Tapered Poles Height 10' (3.0m) 12' (3.7m) 14' (4.3m) 16' (4.9m) 16' (4.9m) 16' (4.9m) 18' (5.5m) 18' (5.5m) 18' (5.5m) 22' (6.7m) 22' (6.7m) 22' (6.7m) 24' (7.3m) 24' (7.3m) 24' (7.3m) 26' (7.9m) 26' (7.9m) 28' (8.5m) 30' (9.1m) 9.0 6.5 13.8 4.2 10.1 2.2 5.9 7.0 13.4 1.4 5.4 5.5 12.0 3.3 3.1 8.9 16.6 1.5 1.0 6.3 12.9 3.9 9.6 1.7 6.6 EPA 70 MPH 80 MPH 90 MPH MPH 33.6 31.4 30.7 30.1 27.1 51.1 42.3 28.9 Steel Round Poles 24.8 22.9 22.0 21.1 18.5 36.9 31.4 21.0 18.8 17.0 16.0 14.9 12.6 27.1 24.0 15.6 EPA 70 MPH 80 MPH 90 MPH MPH 18.5 13.8 10.6 8.2 14.6 10.7 8.0 6.1 11.7 8.4 6.1 4.5 9.9 6.9 4.9 3.4 18.6 13.4 9.8 7.3 32.2 23.2 17.0 12.6 15.5 11.1 8.0 5.8 24.2 17.5 12.9 9.6 37.5 27.7 20.9 16.1 12.5 8.7 6.1 4.2 20.0 14.2 10.2 7.4 31.7 23.1 17.3 13.1 10.0 6.7 4.4 2.8 16.6 11.5 8.0 5.5 26.9 19.4 14.2 10.5 7.8 4.9 3.0 1.5 13.6 9.1 6.0 3.8 22.9 16.2 11.6 8.3 11.1 7.1 4.3 2.3 19.5 13.5 9.4 6.4 16.5 11.1 7.4 4.7 13.8 8.9 5.6 3.2 Outside Dimensions 14.4 12.8 11.7 10.5 8.4 20.2 18.6 11.7 6" (153mm) 6" (152mm) 6" (152mm) 6" (152mm) 6" (152mm) 6" (152mm) Material S11 a. S11 a. S11 a. S11 a. S11 a. S07 a. S07 a. S07 a. Outside Dimensions Material Material S10 S10 S10 S10 S10 S10 S10 S10 C C C D C D C D J C D J D J D J J J N N N Q Q S T T M M M M M M M M s C D J square square square 6" (152mm) square 10-1/8" (257mm) sq. 10-1/8" (257mm) sq. 10-1/8" (257mm) sq. 12" (305mm) sq. 11" (279mm) Dia. 11" (279mm) Dia. N 10-1/8" (257mm) sq. * ** 11" (279mm) Dia. M Round Round Round 10-1/8" (257mm) sq. 10-1/8" (257mm) sq. 10-1/8" (257mm) sq. 11" (279mm) Dia. 11" (279mm) Dia. 11" (279mm) Dia. 12" (305mm) Dia. Q S T 12" (305mm) sq. 12" (305mm) sq. 13-1/2" (343mm) sq. 12" (305mm) Dia. Wall Mount rackets KS O WM * CR Steel Wall Mount plate for flat surfaced arm for use with 5 (127mm) traditional drill pattern. Part# 123111CR 12" (305mm) Dia. 14" (356mm) Dia. 11" (279mm) Dia. All SI ighting Systems poles are guaranteed to meet the EPA requirements listed. SI ighting Systems is not responsible if a pole order has a lower EPA rating than the indicated wind-loading zone where the pole will be located. Caution: This guarantee does not apply if the pole/bracket/fixture combination is used to support any other items such as flags, pennants, or signs, which would add stress to the pole. SI ighting Systems cannot accept responsibility for harm or damage caused in these situations. Note: Pole calculations include a 1.3 gust factor over steady wind velocity. Example: poles designed to withstand 80 MPH steady wind will withstand gusts to 104 MPH. EPAs are for locations miles away from hurricane ocean lines. Consult SI for other areas. Note: Hurricane ocean lines are the Atlantic and ulf of Mexico coastal areas. or applications in lorida or Canada, consult factory. 45' (13.7M) and 50' (15.2M)poles are two-piece; bottom is and top is. If luminaire total weight exceeds 250 lbs. (113.4kg), consult factory. 8" x 8" (203mm x 203mm) 8" x 8" (203mm x 203mm) KS XO WM * CR 2-bolt pattern Steel Wall Mount plate for use with 3 (76mm) traditional drill pattern. Wall Mount Plate Part# 382132CR SI Industries Inc. 3305 13
Pole EPAs Aluminum Square Poles Height EPA 70 MPH 80 MPH 90 MPH MPH 8' (2.4m) 24.3 18.2 14.0 10.9 10' (3.0m) 18.9 13.9 10.5 8.0 12' (3.7m) 14.7 10.6 7.7 5.7 14' (4.3m) 11.9 8.3 5.8 4.1 15' (4.6m) 8.3 5.7 3.8 2.6 16' (4.9m) 7.3 4.8 3.1 1.9 16' (4.9m) 12.3 8.6 6.1 4.3 18' (5.5m) 5.9 3.6 2.1 N/A 18' (5.5m) 10.1 6.8 4.6 3.0 18' (5.5m) 18.0 12.7 9.0 6.4 4.1 2.1 N/A N/A 8.1 5.2 3.1 1.7 15.4 10.5 7.1 4.7 24.8 17.4 12.3 8.7 6" (152mm) 33.8 24.3 17.8 13.2 6" (152mm) 25' (7.6m) 9.5 5.6 3.0 1.0 25' (7.6m) 15.8 10.1 6.1 3.3 6" (152mm) 25' (7.6m) 23.3 15.8 10.7 7.0 6" (152mm) 30' (9.1m) 14.2 8.6 4.8 2.0 6" (152mm) 32' (9.8m) 12.2 6.9 3.2 N/A 6" (152mm) 35' (10.7m) 9.1 4.2 N/A N/A 6" (152mm) Aluminum Round Tapered Poles Outside Material Dimensions 0.250 0.250 0.250 0.250 0.250 Max Weight (lbs) 1 350 260 260 200 200 200 200 150 260 150 150 150 150 260 260 260 260 150 H H I I H I I I I I Structure Weight (lbs) 2 24 28 33 37 39 42 59 46 66 85 51 73 93 114 148 115 139 182 216 229 250 Height EPA Pole Top Pole ottom Material Max Wt Struct. 70 MPH80 MPH90 MPH MPH O.D. 1 O.D. 1 (lbs) 2 Wt (lbs) 3 18' (5.5m) 6.5 4.4 3.1 2.2 3.0 (76mm) 5.0 (127mm) 40 18' (5.5m) 15.4 11.3 8.6 6.8 4.0 (102mm) 6.0 (152mm) 0.156 X 59 18' (5.5m) 18.9 14.0 10.7 8.5 4.0 (102mm) 6.0 (152mm) X 70 5.1 3.3 2.1 1.3 3.0 (76mm) 5.0 (127mm) 42 12.7 9.1 6.8 5.3 4.0 (102mm) 6.0 (152mm) 0.156 X 63 15.8 11.4 8.6 6.8 4.0 (102mm) 6.0 (152mm) X 74 25' (7.6m) 19.4 14.2 10.8 8.5 4.5 (114mm) 8.0 (203mm) 0.156 150 Y 96 25' (7.6m) 24.2 17.8 13.7 10.8 4.5 (114mm) 8.0 (203mm) 150 Y 113 30' (9.1m) 18.8 13.6 10.3 8.0 4.5 (114mm) 9.0 (229mm) 0.156 150 Z 127 30' (9.1m) 23.7 17.4 13.3 10.4 4.5 (114mm) 9.0 (229mm) 150 Z 149 30' (9.1m) 24.2 17.7 13.6 10.7 4.5 (114mm) 8.0 (203mm) 0.250 150 Y 174 Aluminum Pole EPAs s H Square Square 9-15/16" (252mm) Square ase Plate 11-9/16" (294mm) Square ase Plate 9" (229mm) Dia. +/- 1/2 (13mm) O.D. Pole ottom 9-5/8" (244mm) square base plate 8-5/8" (219mm) Dia. +/- 7/8" (22mm) Y 8" (203mm) O.D. Pole ottom 12-1/16"(306mm) square base plate 11-5/8" (295mm) Dia. +/- 3/8" (9mm) 11" (279mm) Dia. +/- 1/2 (13mm) I 6" (152mm) Square 12-3/4" (324mm) Square ase Plate 12-1/2" (318mm) Dia. +/- 7/16 (11mm) X 6" (152mm) O.D. Pole ottom 10-5/16" (262mm) square base plate 9-1/2" (241mm) Dia. +/- 3/4" (19mm) Z 9" (229mm) O.D. Pole ottom 12-1/2" (317mm) square base plate 13-1/4" (337mm) Dia. +/- 3/4" (19mm) All poles are guaranteed to meet the EPA requirements listed. Pole manufacturer is not responsible if a pole order has a lower EPA rating than the indicated wind-loading zone where the pole will be located. CAUTION: This guarantee does not apply if the pole/bracket/fixture combination is used to support any other items such as flags, pennants, or signs, which would add stress to the pole. Pole manufacturer cannot accept responsibility for harm or damage caused in these situations. NOTE: Pole calculations include a 1.3 gust factor over steady wind velocity. Example: poles designed to withstand 80 MPH steady wind will withstand gusts to 104 MPH. EPAs are for locations miles away from hurricane ocean lines. Consult SI for other areas. Note: Hurricane ocean lines are the Atlantic and ulf of Mexico coastal areas. or applications in Canada and areas using code requirements other than AASHTO TS-3-94, consult factory. SI Industries Inc. 3305 14
Aluminum Pole EPAs Pole EPAs Aluminum Round Poles Height 8' (2.4m) 10' (3.0m) 10' (3.0m) 12' (3.7m) 12' (3.7m) 12' (3.7m) 12' (3.7m) 14' (4.3m) 14' (4.3m) 14' (4.3m) 14' (4.3m) 16' (4.9m) 16' (4.9m) 16' (4.9m) 16' (4.9m) 18' (5.5m) 18' (5.5m) 18' (5.5m) EPA 70 MPH 80 MPH 90 MPH MPH 10.7 7.9 6.0 4.7 8.1 5.9 4.3 3.3 15.4 11.5 8.9 7.1 6.2 4.3 3.0 2.2 12.2 9.0 6.9 5.5 15.5 11.5 8.9 7.1 18.8 14.0 10.9 8.7 4.6 3.0 1.9 1.2 9.7 6.9 5.3 4.1 12.5 9.1 7.0 5.5 15.3 11.2 8.7 6.9 3.2 1.9 1.0 0.5 7.4 5.1 3.8 3.0 9.8 6.9 5.3 4.1 12.2 8.7 6.7 5.3 5.6 3.7 2.7 2.0 7.7 5.2 3.9 3.0 9.7 6.8 5.1 4.0 4.1 2.4 1.7 1.2 5.9 3.8 2.8 2.0 7.6 5.2 3.8 2.9 Outside Dimensions Aluminum Round Hinged ase Poles Material 0.156 0.156 0.156 0.156 0.156 Max Weight (lbs) 1 75 75 75 E E E E E Structure Weight (lbs) 2 Height EPA Outside Material Max Weight Structure 70 MPH 80 MPH 90 MPH MPH Dimensions (lbs) 1 Weight (lbs) 2 8' (2.4m) 10.8 8.0 6.1 4.8 50 W 19 10' (3.0m) 8.2 5.9 4.4 3.3 50 W 22 10' (3.0m) 15.5 11.6 9.0 7.2 50 W 27 12' (3.7m) 6.3 4.4 3.1 2.2 50 W 26 12' (3.7m) 12.4 9.1 7.0 5.6 50 W 32 12' (3.7m) 15.7 11.6 9.0 7.2 0.156 50 W 38 12' (3.7m) 18.9 14.1 11.0 8.8 50 W 45 14' (4.3m) 4.7 3.1 2.0 1.3 50 W 30 14' (4.3m) 9.8 7.0 5.4 4.2 50 W 36 14' (4.3m) 12.6 9.2 7.1 5.6 0.156 50 W 44 14' (4.3m) 15.4 11.3 8.7 6.9 50 W 52 16' (4.9m) 3.4 2.0 1.1 0.5 50 W 33 16' (4.9m) 7.6 5.2 3.9 3.0 50 W 41 16' (4.9m) 10.0 7.1 5.4 4.2 0.156 50 W 50 16' (4.9m) 12.3 8.9 6.8 5.3 50 W 58 18' (5.5m) 5.7 3.7 2.7 2.0 75 W 45 18' (5.5m) 7.7 5.3 4.0 3.0 0.156 75 W 55 18' (5.5m) 9.8 6.8 5.2 4.0 75 W 65 4.2 2.5 1.7 1.2 75 W 50 6.0 3.9 2.8 2.1 0.156 75 W 61 7.7 5.2 3.9 2.9 75 W 72 lat luted Round Poles Height EPA Outside Material Max Weight RN2 RN3 80 MPH 90 MPH MPH Dimensions (lbs) 1 Wt (lbs) 2 Wt (lbs) 2 8' (2.4m) 13.3 10.2 8.0 300 O/P 67 74 8' (2.4m) 21.9 17.0 13.4 300 O/P 69 76 10' (3.0m) 9.1 6.8 5.2 300 O/P 70 78 10' (3.0m) 15.5 11.8 9.1 300 O/P 73 81 12' (3.7m) 6.3 4.5 3.2 300 O/P 74 81 12' (3.7m) 11.2 8.3 6.2 300 O/P 78 85 12' (3.7m) 17.2 13.1 10.0 6" (152mm) 300 O/P 82 87 14' (4.3m) 8.1 5.7 4.0 300 O/P 82 90 14' (4.3m) 13.1 9.5 6.9 6" (152mm) 300 O/P 87 93 16' (4.9m) 5.7 3.7 2.2 300 O/P 87 94 16' (4.9m) 9.7 6.7 4.5 6" (152mm) 300 O/P 93 98 16' (4.9m) 10.3 7.3 5.2 300 O/P 103 109 18' (5.5m) 3.7 1.9 N/A 300 O/P 91 99 18' (5.5m) 7.0 4.4 2.5 6" (152mm) 300 O/P 98 104 18' (5.5m) 12.9 9.1 6.3 6" (152mm) 300 O/P 120 125 19 22 27 26 32 38 45 30 36 44 52 33 41 50 58 45 55 65 50 61 72 s E Round 8-15/16" (226mm) Square ase Plate 7-1/2" (191mm) Dia. +/- 3/4" (19mm) O 4", 5", & 6 RN2 17"(432mm) diameter base plate 180 o 90 o 270 o 11-1/2" (292mm) Dia. +/- 1-1/2" (38mm) All poles are guaranteed to meet the EPA requirements listed. Pole manufacturer is not responsible if a pole order has a lower EPA rating than the indicated wind-loading zone where the pole will be located. CAUTION: This guarantee does not apply if the pole/bracket/fixture combination is used to support any other items such as flags, pennants, or signs, which would add stress to the pole. Pole manufacturer cannot accept responsibility for harm or damage caused in these situations. NOTE: Pole calculations include a 1.3 gust factor over steady wind velocity. Example: poles designed to withstand 80 MPH steady wind will withstand gusts to 104 MPH. EPAs are for locations miles away from hurricane ocean lines. Consult SI for other areas. Note: Hurricane ocean lines are the Atlantic and ulf of Mexico coastal areas. or applications in Canada and areas using code requirements other than AASHTO TS-3-94, consult factory. W & Round Hinged 12-5/8"(321mm) diameter base plate 9-1/4" (235mm) Dia. +/- 3/4"(19mm) Round 9-5/8" (244mm) Square ase Plate (optional) 8-5/8" (219mm) Dia. +/- 7/8" (22mm) P 4", 5", & 6 RN3 17"(432mm) diameter base plate 0 o - Access Door 0 o - Access Door 11-1/2" (292mm) Dia. +/- 1-1/2" (38mm) SI Industries Inc. 3305 15
Wind Speed Map SI Industries Inc. 3305 16
SI Poles can be drilled for nearly any fixture (not only SI fixtures). Of course, when you order your entire lighting system from SI, you guarantee a precise color match between fixture, pole and brackets. Contact Us Today to learn about how we can help you! 00 Alliance Road Cincinnati, Ohio 45242 (513) 793-3200 AX (513) 793-0147 www.lsi-industries.com SI INDUSTRIES INC. 7/16 3305