MILTON ROY INDIA (P) LTD Metering Pumps Instruction Manual PN-Z PACKED PLUNGER PUMP This Manual should be made available to person responsible for installation, maintenance and operation. PUMP MODEL: SERIAL NO: CAPACITY: LPH: PRESSURE: Issue Date: 07/200
TABLE OF CONTENTS Page No WARRANTY 3 IMPORTANT SAFETY INSTRUCTION 4 QUICK START GUIDE 5.0 INTRODUCTION. General Description 6.2 Principles of Operation 6.3 Technical Details 7 2.0 INSTALLATION 2. Unpacking 8 2.2 Storage / Idle Service 8 2.3 Mounting 8 2.4 Electrical Installations 9 2.5 Piping 9 3.0 START UP 0 4.0 LUBRICATION SCHEDULE 5.0 MAINTENANCE 6.0 BASIC PARTS 3 7.0 TROUBLE SHOOTING 9 2
METERING PUMP PRODUCTS TWELVE MONTH LIMITED WARRANTY Milton Roy India private Limited Company warrants its metering pump product against defects in workmanship or material for one year under normal use from the date of shipment form our warehouses as indicated in our warranty certificate. All obligations and liabilities under this warranty are limited to refunding, repairing or replacing (at our option) f.o.b, our plant, such allegedly defectives units are returned to our plant, carrier charges prepaid. Repairs or replacement are made subject to factory inspection of returned items. This warranty does not extend to damage by corrosion or atmosphere. The materials of construction offered are recommendations subject in all cases to verification and acceptance by the customer. These recommendations, based on previous company experience and best available information s, do not constitute guarantees against wear and chemicals action. Expressly excluded from this warranty are defects caused by misuse, abuse or improper application/installation, employment or operation of the unit. Expendable items and damage resulting from unauthorized repair are not covered by this warranty. No liability for consequential damage or reinstallation labour is accepted. Milton Roy India Private Limited will not assume responsibility for contingent liability for alleged failure of its products. RETURNING PUMPS TO THE FACTORY Pumps will not be accepted for repair without a written consent from the Factory Service Department. Pumps returned to the Factory for repairs should be clearly labeled to indicate the liquid being pumped. Process liquid should be flushed from the pump liquid end and oil should be drained from the pump housing before the pump is shipped. NOTE: These safety precautions will aid the troubleshooting and repair procedure and preclude serious injury to repair personnel from hazardous residue in pump liquid end. All inquiries or parts orders should be addressed to your local Milton Roy India (P) Ltd., representatives or sent to: MILTON ROY INDIA (P) Ltd., NO.: 4, RAJARAJAN STREET, VISALAKSHI NAGAR EKKADUTHANGAL, CHENNAI - 600 032. PHONE NO.: (044) - 42266333 FAX NO.: 9-44-45540060. 3
IMPORTANT SAFETY INSTRUCTIONS WARNING WARNING WHEN INSTALLING, CALIBRATING, OR OPERATING THIS ACTUATOR, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS INJURY. Read all instructions before installation, calibration, or operation GENERAL SAFETY CONSIDERATIONS - Read this manual carefully. - Installation, calibration, and maintenance should be performed by trained and qualified personnel. Personnel should be familiar with the precautions required in working with hazardous voltages which exist inside the actuator. Personnel should also be adequately trained on any hazards inherent in the chemicals used in the metering pump. - Always wear protective clothing including gloves and safety glasses when working on or near chemical metering pumps. - Follow directions and warnings provided with the chemicals from the chemical manufacturer. User is responsible for determining the hazards associated with the chemicals being pumped and using the proper safety gear and procedures. - Hazardous voltages are present when cover is removed. Disconnect power when installing or servicing this unit. - Unit must be properly grounded. - Conform to local codes in wiring this equipment. - Pump must be adequately rated if it is to be used in a hazardous location. See product data plate for rating information. This rating must not be exceeded under any circumstances. To prevent ignition of hazardous atmospheres, cover must be tight while circuits are energized. - In order to comply with the requirements of agency approvals (see data plate), specifications for conduit connections, wire gauge and type, fastener torque ratings, and operating conditions must be adhered to. QUICK START GUIDE 4
NOTE: Read and understand safety instructions before proceeding. READ CONNECT VERIFY - Read and comply with all safety instructions presented in this manual. In order to comply with the requirements of agency approvals (see data plate), specifications for conduit connections, wire gauge and type, fastener torque ratings, and operating conditions must be adhered to. - Connect AC power. Use conduit connections or cable glands. - Ground unit. - Connect command signal. - Connect feedback signal. - Voltage selector switch is set to the required voltage (230 VAC). - Command input signal is set to desired operation 4-20 ma. Factory set at 4-20 ma or (- 5V DC). - Feedback signal output is set to desired operation 4-20 ma or (-5 VDC). Factory set at 4-20 ma. WARNING HAZARDOUS VOLTAGES ARE PRESENT ON THE CIRCUIT BOARD. TO PREVENT IGNITION OF HAZARDOUS ATMOSPHERES, COVER MUST BE TIGHT WHILE CIRCUITS ARE ENERGIZED. APPLY POWER OBSERVE CALIBRATE FINISH - Apply command signal. - Apply AC power. - Actuator should run to command position and stop. - Full range of command signal should result in desired range of actuator travel (factory setting is for full - Travel of 0% to 00%). - If actuator was installed on the pump at the factory, it has been factory calibrated. - If actuator is a retrofit or a non-standard range is desired, follow the calibration instructions in this manual. - Install cover. 5
SECTION INTRODUCTION. GENERAL DESCRIPTION The PN-Z packed plunger pumps are dosing pumps equipped with a packed plunger liquid end, oil bath lubricated gears in a sealed casing. Adjustment of stroke length can be carried out as the pump is operating or at stop. It is designed for non-stop industrial service..2 PRINCIPLE OF OPERATION The Movement of rotation of the motor is transmitted by the worm to the tangent wheel. The system of rod and eccentric transforms the rotary movement into a linear movement. The cross slide connected to the connecting rod move with an adjusting linear stroke. The stroke of the cross slide depends to the position of the slide and the eccentric female. 6
.3 TECHNICAL DETAILS: Maximum Discharge Pressure : Kg/cm2 Maximum Flow : LPH @ Max Pressure. Stroke per Minute : SPM Reduction Ratio : Stroke Length : mm Motor Power : HP Plunger Diameter : mm Motor Speed : 440 RPM Motor Input : 45V, 3 Phases, 50 HZ Weight : 44 Kg (Approx.) Repeatability : +/- 3% Linearity : +/- 3% Steady State Accuracy : +/- % Flow Temperature : -5 to +0 % 7
SECTION 2 INSTALLATION 2. UNPACKING Pumps are shipped F.O.B factory and title passes to customer when carrier signs for receipt of pump. In the event that the damages occur during shipment, it is the responsibility of the customer to notify the carrier immediately and to file a damage claim. Carefully examine the shipping crate upon receipt from carrier to be sure there is no obvious damage to contents. Open the crate carefully so that the accessory items fastened to the inside of the crate will not be damaged or lost. Examine all material inside crate and check against packing specification to be sure that all items are accounted for and intact. 2.2 STORAGE & IDLE SERVICE Pumps that are not expected to put in service within 90 days of receipt should be stored in a dry place. Apply grease to all the non-painted surface of the pumps. Protect rubber parts from direct sun and from daily temperature variations. FAILURE TO PROPERLY STORE AND PROTECT THE EQUIPMENT MAY VOID ANY WARRANTY, EXPRESSED OR IMPLIED. OUTDOOR STORAGE IS NOT RECOMMENDED UNDER ANY CIRCUMSTANCES UNLESS SPECIFICALLY PREPARED FOR STORAGE PRIOR TO SHIPMENT FROM THE FACTORY. Maximum Estimated Storage Indoors, dry ambient controlled temperature: Initial - - - - - - - - - - - - - 2 months Extend preservation - - 2 additional months Indoors, dry ambient uncontrolled temperature: Initial - - - - - - - - - - - - - - - 6 months Extend preservation- - - - - 6 additional months Outdoor storage: Not recommended. 2.3 MOUNTING Support the pump firmly in a level position on a solid, vibration free foundation preferably with the base above floor level to protect the pump from wash downs and to provide easier access for service. The Pump is provided with mounting holes to accommodate anchor bolts. A Roof should protect pumps installed outdoors. 8
2.4 ELECTRICAL INSTALLATION Verify the Motor data against your available main supply for the plant before carrying out connections. Connect the motor according to the indications given in the terminal box and the name plate of the motor. Before operating the pump, check the direction of rotation of motor which must be according to the arrow stamped on the motor adaptor base (Counter clockwise direction when seen from top). To reverse the direction of rotation just reverse either of the two phases of incoming power supply. DO NOT FORGET TO CONNECT THE PUMP TO EARTH Electric protection of the motor (Thermal protection or by means of fuse) is to correspond to the rated current indicated on the motor data plane. 2.5 PIPING Connect suitable sizing of suction and discharge piping. The piping material should be suitable for the chemical being pumped. Ensure that the thickness of pipe is suitable for withstanding the pressure requirements. Generally for high discharge pressures use seamless schedule 80 piping on the discharge line. Ensure that a strainer is fitted in the suction line and a suitable pressure relief valve is fitted in the discharge line. If required provide a pulsation dampner of suitable capacity. Capacity of the pulsation dampner is usually selected as 00 times the flow per stroke of the pump for fills and draw type. It is recommended to install a check valve at the point of dosing. 9
SECTION 3 START UP. Line up the pump with suitable suction piping and suitable accessories. 2. Open the isolation valves in suction and discharge piping. 3. Ensure that all the fasteners are fully tightened. 4. Fill the pump drive with Lts of Hydrol 220 or equivalent oil. 5. Keep the stroke length at 5 to 20 %. 6. Run the motor and check the direction of rotation. It should be counter clockwise when viewed from Top. 7. At Zero discharge pressure ensure that the pump is delivering liquid. 8. Slowly increase the stroke length to 00%. 9. Allow the pump to run for some time. 0. Connect the discharge line with pressure relief valve.. Allow the pump to run for some time and ensure the pressure relief valve is relieving at the correct pressure. 2. Adjust the stroke knob to the required percentage and tighten the lock knob. 3. Observe for abnormal noise and vibration. 4. Check for any leak on the suction and discharge valves and tighten suitable. 5. Apply some grease or oil on the cross slide. This will help in reducing friction in the oil seal. Do not remove the cover on the cross slide without stopping the pump. 0
SECTION 4 LUBRICATION SCHEDULE The Pump drive should be filled with the specified oil till half of the sight glass (app..0 Lts). The recommended hydraulic oils for the pump are shown below. MANUFACTURER TYPE BHARATH PETROLEUM HYDROL 220 INDIAN OIL CORPORATION SERVO SYSTEM 220 HINDUSTAN PETROLEUM ENCLO - 220 SECTION 5 MAINTENANCE The Pumps are designed to provide maintenance free operation for long periods. However, certain maintenance precautions are required for trouble free operation.. Ensure oil level in the pump drive unit at least once in 5 days. 2. Ensure that the cross slide is suitably lubricated at least once a week by applying small amounts of oil on the oil seal area to ensure friction free running. 3. Tighten the bolts of the cross slide guide and head periodically once in 5 days. 4. Change the entire drive oil after 500 Hrs of initial running and later every 2000 Hrs of operation. 5. Ensure that the check valves are not blocked or clogged once a month by flushing the liquid end. Clogging of the check valves will result in erratic discharge or no discharge. Complete blockage of the check valves will result in damage to the pump drive. 6. Lubricate the stroke adjustment mechanism once a month through the lock knob with grease or oil.
2
6.0 BASIC PARTS: PN-Z DRIVE END ITEM NO PART NO DESCRIPTION QUANTITY RECOMMENDED SPARES 47020 Housing 2 47844 Gear (/0) 478244 Gear (/5) 478344 Gear (/25) 3 470420 Connecting Rod 4 47052 Eccentric 5 47062 Shoe 6 47072 Sliding Crank 8 22826 Circlip B26 9 3526 Bearing 6000 0 47092S Cover WITH O-RING SET 47082 Adjustment Screw 4 4772S Knob with Grub Screw SET 5 479452 Lock Bolt Stopper 4mm Ball 6 47932 Stroke Lock Knob (PN-Z) 7 4702 Cross Slide (PN-Z) 8 M070 Circlip C6 9 523S Oil Cap with Gasket SET 20 M0704 Allen Cap Screw M6 x 25 4 4 47820 Cross Slide Guide 6-6 (PN-Z) 2 47920 Cross Slide Guide (20~25) 472020 Cross Slide Guide (32~40) 22 4722 Dowel Pin 25 4732 Plunger Fixing Nut (Dia 6 to 6) 4742 Plunger Fixing Nut (Dia 20 to 40) 26 4762 Cross Slide Lock Nut 27 4752 Cross Slide Nut 28 835 Sight Glass 30 47302 Stroke Label (PN-Z) 3 M0703 Allen Cap Screw M5 x 6 4 4 32 94025 Circlip A0 33 4442 Allen Cap Screw M5 x 20 4 4 34 3926 Bearing 620 2 2 35 47842 Worm Shaft (/0) 47852 Worm Shaft (/5) 3
47862 Worm Shaft (/25) 472220S Bearing Cap with O-RING (63 Frame) 37 472320S Bearing Cap with O-RING (7 Frame) SET 472420S Bearing Cap with O-RING (80 Frame) 38 8343S OIL DRAIN PLUG WITH O-RING SET 473520S Coupling - Flexible with Grub Screw 63 FRAME MOTOR 4 473620S Coupling - Flexible with Grub Screw 7 FRAME MOTOR SET 42 473720S Coupling - Flexible with Grub Screw 80 FRAME MOTOR 472520 Motor Adaptor (80 Frame) 472620 Motor Adaptor (7 Frame) 472720 Motor Adaptor (63 Frame) 43 55226 Hex Bolt M8 x 20 4 44 500570 Motor - 0.25 HP Motor 440 rpm Flange 500750 Motor - 0.5 HP Motor 440 rpm Flange 500760 Motor - 0.5 HP-FLP Motor 440 rpm Flange 45 22552S O-RING SET - PNZ DRIVE END - SIMPLEX 46 M069 Oil Seal X 22 X 7 47 4452 Allen Cap Screw M5 x 30 4 4 48 4732 47322 47332 47342 47332 47562 Support for Cross Slide Guide (6 to 6) (63 Frame) Support for Cross Slide Guide (20 to 40) (63 Frame) Support for Cross Slide Guide (6 to 6)(7 Frame) & (20 to 40)(80 Frame) Support for Cross Slide Guide(20 to 40) (7 Frame) Support for Cross Slide Guide (6 to 6)(7 Frame) & (20 to 40)(80 Frame) Support for Cross Slide Guide (6 to 6) (80 Frame) 2 49 M0704 Allen Cap Screw M6 X 25 (HT) 2 2633 Hex Nut M6 SS 2 M0202 M6 Washer SS 2 4
5
6
6.2 BASIC PARTS: PN-Z DRIVE END DUPLEX ITEM NO PART NO DESCRIPTION QUANTITY RECOMMENDED SPARES 47020 Housing 2 2 47844 Gear (/0) 478244 Gear (/5) 478344 Gear (/25) 2 2 3 470420 Connecting Rod 2 4 47052 Eccentric 2 5 47062 Shoe 2 6 47072 Sliding Crank 2 7 47252 O-Ring (60 x 3.5) 2 2 8 22826 Circlip B26 2 2 9 3526 Bearing 6000 2 0 47092S Cover WITH O-RING 2 47082 Adjustment Screw 2 2 44252 O-ring 2 2 3 4433 Grub Screw M6 x 0 0 4 4772S Knob with Grub Screw 2 5 479452 Lock Bolt Stopper 4mm Ball 2 4 6 47932 Stroke Lock Knob (PN-Z) 2 7 4702 Cross Slide 2 8 M070 Circlip C6 2 2 9 523S Oil Cap with Gasket 2 20 M0704 Allen Cap Screw M6 x 25 8 2 47820 Cross Slide Guide (6~6) 47920 Cross Slide Guide (20~25) 472020 Cross Slide Guide (32~40) 2 22 4722 Dowel Pin 2 2 23 47252 O-Ring (43 x 3.5) 2 2 24 472952 Oil Seal (25 x 40 x 7) 2 2 25 4732 Plunger Fixing Nut (Dia 6 to 6) 4742 Plunger Fixing Nut (Dia 20 to 40) 26 4752 Cross Slide Nut 2 27 4762 Cross Slide Lock Nut 2 28 835 Sight Glass O-ring 2 30 47302 Stroke Label (PN-Z) 2 3 M0696 Allen Cap Screw M5 x 6 8 7 2
32 94025 Circlip A0 2 2 33 4442 Allen Cap Screw M5 x 20 8 34 3926 Bearing 620 4 47872 Worm Shaft Multiplex (/0) 47882 Worm Shaft Multiplex (/5) 35 47892 Worm Shaft Multiplex (/25) 47842 Worm Shaft (/0) 47852 Worm Shaft (/5) 47862 Worm Shaft (/25) 36 472052 O Ring 37 X 3.5 (PN-Z) 2 2 472220S Bearing Cap with O-RING (63 Frame) 37 472320S Bearing Cap with O-RING (7 Frame) 472420S Bearing Cap with O-RING (80 Frame) 38 8343 Drain Plug 39 904655 Drain Plug O-Ring 40 472852 Oil Seal 8 X 6 X 7.5 473520 Coupling - Flexible 63 FRAME MOTOR 4 3320S Coupling - Flexible 7 FRAME MOTOR 33220S Coupling - Flexible 80 FRAME MOTOR 472520 Motor Adaptor (80 Frame) 42 472620 Motor Adaptor (7 Frame) 472720 Motor Adaptor (63 Frame) 43 55226 Hex Bolt M8 x 20 4 500570 Motor - 0.25 HP Motor 440 rpm Flange 44 500750 Motor - 0.5 HP Motor 440 rpm Flange 500760 Motor - 0.5 HP-FLP Motor 440 rpm Flange 8
SECTION 7 TROUBLE SHOOTING SYMPTOMS CAUSES REMEDIES Pump does not Operate Insufficient Delivery Erratic Delivery Gear Shaft Breakage Blown Fuse Motor Trip Low Liquid Level Worn or Dirty Check Valves Blocked Discharge Line Broken Wire Low Voltage Pump not primed Capacity Adjustment Set at Zero. Incorrect Capacity Adjustment Incorrect Pressure Relief valve Settings. Starved Suction Leaky Suction Piping Leaky Pressure Relief Valve Worn or Dirty Check Valves Leaky Suction Piping Leaky Pressure Relief Valve Incorrect Pressure Relief valve Settings. Worn or Dirty Check Valves Clogged or Dirty line Strainer Plunger or cross slide hitting against liquid end. Check for Short Circuit Check for Overload, Correct current setting in relay. Fill Liquid Clean and Replace Clear Line Locate and Repair Investigate and Correct Allow Suction Line and pump head to fill with liquid before pumping against pressure. Readjust. Readjust Capacity Correct the Pressure Relief Valve Settings Increase Pipe Sizing or Suction Head. Repair Piping Repair or Replace Pressure Relief Valve. Clean and Replace Repair Piping Repair or Replace Pressure Relief Valve. Correct the Pressure Relief Valve Settings Clean and Replace Clean Strainer Correct and change the gear shaft. Pump not developing Pressure Leaky Gland Packing Leaky Pressure Relief Valve Incorrect Pressure Relief valve Settings. 9 Tighten Gland Packing Add Rope Change Entire Packing Correct or replace pressure relief valve Correct the Pressure Relief Valve Settings
20
2