ProCash 2050xe Short installation manual

Similar documents
330mm (13") MAXIMUM WALL THICKNESS IN AREA OF UNIT. 330mm (13") MAXIMUM WALL THICKNESS IN AREA OF UNIT (30 HEIGHT NOTE SEE W ALL OPENING

203mm (8") MAXIMUM WALL THICKNESS IN AREA OF UNIT. 203mm (8") MAXIMUM WALL THICKNESS IN AREA OF UNIT (30 HEIGHT NOTE SEE W ALL OPENING

OPTEVA 378 ENHANCED CASH RECYCLER TERMINAL FRONT LOAD LOBBY UNIT PLAN VIEW FRONT VIEW SIDE VIEW

OPTEVA 923 IN LOBBY TELLER (ILT) PLAN mm (60") WIDE PLAN - STAND ALONE FRONT VIEW SIDE VIEW PAGE 1 OF 5 CALL NOTE:

EDB-EPD, EGB-EPD and EJB-EPD (Equipment Protection Device) Circuit Breakers for Ground Fault Protection in NF Panelboards

UL AND CODE COMPLIANCE

ICOMIA Global Conformity Guideline for ISO/ABYC Standards and Canadian TP 1332 requirements. Guideline Number 3 Electrical

Start UP Guide. Symmetra LX Tower Rack-Mount. UPS Models 200 V, 4-8 kva 208/240 V, 4-8 kva 220/230/240 V, 4-8 kva

BAL3000 BAL3000. Fluorescent Emergency Ballast Lumens. Specification Sheet. Emergency Ballast 1/19/2012. Project: Catalog#: Approved by:

Indoor or Outdoor 2400 to 14,400 Volts 600 to 14,400 Kvac, 3 Phase, 60 Hz

BAL1400 FLUORESCENT EMERGENCY BALLAST Specification-grade One or two-lamp emergency illumination

BAL3000 FLUORESCENT EMERGENCY BALLAST Specification-grade: Up to 3500 lumens One or two-lamp emergency illumination

Understanding Electrical Terms

Smart Battery Charger

Softstarter Intelligent Controllers

A. Motors shall be designed, built, and tested in accordance with the latest revision of the following standard documents.

Extensible Unit - VCE2a

University of Houston Master Construction Specifications Insert Project Name SECTION ELECTRONIC VARIABLE SPEED DRIVES PART 1 - GENERAL

Copyright 2012 DelSolar Co. Ltd MQWRD installation manual-iec Ver. 1.4

Electrical Installation

BALT5-800 LOW-PROFILE FLUORESCENT EMERGENCY BALLAST

Medium voltage products UniSec DY800 New 24 kv air-insulated medium voltage switchgear to e-distribuzione specifications

VD4 Installation and service instructions kv A ka

Models beginning with MO, MK, 7B, 6S, 6F or 5B. Product Description. Technical Specifications. Installation Instructions.

TEMPORARY ELECTRIC WIRING FOR CARNIVALS, CONVENTIONS, EXHIBITIONS, FAIRS AND SIMILAR USES

KD1E Range Potential Indicators

North America Phase Converters & Electrical Supply

Disconnect Switch and Circuit Breaker Mechanism Specifications Bulletin Number 1494

GP Dimming Panels 230 Volt (CE)

IMPORTANT SAFEGUARDS

PowerAir Compressor Installation

INSTALLATION MANUAL.

1329I Integrated Drive/Motor CE Filter Option Kit

w w w.apc.com Home Appliance & Lighting UPS HI800SQ Installation Guide and User s Manual

GP Dimming Panels 230 Volt (CE)

M-3025CB-AV Fuel Pump

9. Non-Residential Services (Commercial, Industrial, and Agricultural)

GP Dimming Panels. GRAFIK Systems SPECIFICATION SUBMITTAL

Capacitors. Individual & fixed bank. Individual & fixed capacitor banks. Low Voltage Network Quality

SineWave Guardian TM 380V 600V INSTALLATION GUIDE. Quick Reference. ❶ How to Install Pages 6 17 ❷ Startup/Troubleshooting Pages WARNING

Lumencia. LLMPS SERIES Micro Power Systems. Multi-Unit Residential Lighting. Job Name: Type:

MK Electric IP Solutions

STL. Series. Emergency Lighting Inverter 3kW to 160kW Central System

Boston Gear Ratiotrol DC Motor Speed Control

Illuminator Series CR NEMA 3R

Selection Information Molded Case Circuit Breakers

LP Dimming Panels. GRAFIK Systems

EMERGENCY ONE-LED TM SOLO TM NON MAINTAINED LED LAMP AND DRIVER KIT

TECHNICAL SPECIFICATION FOR 11 KV AUTOMATIC CAPACITOR SWITCH

Compact SE Overview. High-Performance Dimming. Ballast

Safety and General Information

ClassicSeries Compressor Installation

Electric Range installation manual

Order No. of the options EMC filter Class A

Demand Switch NEFA20 Plus. Installation Guide. Please read this entire guide before beginning the installation!

INSTRUCTION MANUAL. IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following:

DUAL 60V 20A POWER FLEX POWER SUPPLY INSTRUCTION MANUAL

OPERATION INSTRUCTIONS

530 Power. Grounding. Line voltage. Caution. A proper earth ground is required for GC operations.

HGM501 Gen-set Controller USER MANUAL. Smartgen Technology

How to Order 1 T Z A. r Pressure range. 05 Pressure range 0 to 0.5 MPa 10 Pressure range 0 to 1 MPa 16 Pressure range 0 to 1.6 MPa

Defender Mini Online Emergency Central Lighting Inverter (CLI) Technical Specifications

UNIVERSAL LIGHT 15-24W. IP64 WARRANTY

HD UNIT INSTALLATION & SERVICE BOOKLET 3-7

Installation And Operation Instructions

5. High voltage warning labels should be placed on all cabinet doors and terminal covers enclosing equipment operating at above 50 volts.

SECTION MOTOR CONTROL

General Installation Manual Mar 2009, Sanyo Electric Co., Ltd. All Rights Reserved 3/23/09

EcoSystem Multiple Control Input Ballasts

CIVACON GROUND VERIFICATION RACK MONITOR SYSTEM and ASSOCIATED EQUIPMENT

Installation Instructions

Product Manual & Installation Guide Vertical Rack Mount 5.0 to 8.6 kw

Bussmann series IEC cylindrical fuses

INSTALLATION AND OPERATING INSTRUCTIONS OF THE INTERNATIONAL ISOBOX SERIES ISOLATION TRANSFORMERS.

Phase-Adaptive Power Module

ILLUMINATOR LV. Emergency Lighting Inverter System 175VA through 750VA. Illuminator Series LV Single Phase

55185 EMERGENCY PACK FOR LED PANEL TECHNICAL DATA SHEET

NEMA Contactors & Starters A200

SloanLED THINLED. Constant Current. Installation Guide

HPS Imperator Machine Tool Industrial Control Transformer

Powerware 9390 Integrated Battery Cabinet (Models IBC-S and IBC-L) Installation Manual

SECTION MOTORS AND VARIABLE FREQUENCY DRIVES

QUEENSLAND URBAN UTILITIES

Xenon Fiberoptic Lightsource

SPECIFICATIONS - DETAILED PROVISIONS Section Vertical Hollowshaft Electric Motors C O N T E N T S

SECTION MOTOR REQUIREMENTS for HVAC

Electronic Temperature Control & Bulb Well Assembly (AC)

High Frequency SineWave Guardian TM

Electrical Equipment and Terminology

Rescue Pac. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference

Model #: APS V DC or 120V AC input; 120V AC output (hardwired) Auto Transfer Switching option for battery backup / UPS operation

INSTALLATION AND OPERATING INSTRUCTIONS OF THE INTERNATIONAL ISOBOX SERIES ISOLATION TRANSFORMERS.

SITESTAR ELECTRONICS CABINET DESCRIPTION

Electrical Wiring Practices

3000W POWER INVERTER. User Manual

EcoSystem Multiple Control Input Ballasts

G2.1 RETROFIT LED LIGHTING

SPECIFICATION SHEET :FH6-DUAL-3000L. Project Type Model # Remarks

Illuminator Series CM. GUIDE SPECIFICATIONS And TECHNICAL DESCRIPTION. 500W, 1000W, 1500W and 2000W Single-Phase Emergency Power System

EcoSystemR Multiple Control Input Ballasts

Transcription:

Proash 00xe SPEFKTONS Physical Security This TM meets the following Security standards EN 090, UL090 and meets the attack test per UL 9-, S.-090, E 090. The safe door has a relocking feature. The controlling of safe door is by keys, combination lock with keys or optional electronic lock. larm Protection The UL - listed safe is equipped with a basic alarm sensor package. The package includes a safe cabinet door open switch. Optional seismic sensor. Power Requirements This TM meets the following EM standards EN 0 class, EN0, EN 00-, EN 00-, EN000--, EN000--, F FR, part subpart class, ES-00 (S 0. and SM- Standard NS class. The E symbol indicates that the product complies with the following EU directives. EM 9//E, 9//E, 9//E and 9//E and on Low voltage directive / security //E and 9//E. The TM requires a single-phase three-wire unswitched power outlet. Wiring to the TM must use a third-wired earth ground (conduit ground is not acceptable. The power supplied must be as specified below: 0-0 / 0-0 V (- 0 to + % at 0/0 Hz (+/- %, single phase Network structure Each TM must have a dedicated outlet/circuit. Power to the TM may be a branch or dedicated service and must be protected by a safety quick-disconnect device the break line voltage (such a circuit breaker at the electrical service panel. The quick disconnect device (or circuit breaker must turn off the line voltage at the amperage specified below. Fuse for the evice 0-0 V service, disconnect at 0 amps or Fuse 0-0- V service, disconnect at 0 amps egree of Protection (EN 09 Outdoors / ndoors Other electronic devices sharing power on a common branch circuit must conform to the same conducted interference standards as the TM. Power Usage for TM without UPS Rated urrent onsumption (Maximum Operation 0-0 V / 0-0 V. /. pparent Power onsumption (Maximum Operation 0-0 V / 0-0 V 0 / 0 V Real Output 0-0 V / 0-0 V 00 / 9 TU/h Power factor 0-0 V / 0-0 V 0.9 / 0. Protection lass Leakage urrent (Maximum 0-0 V / 0-0 V. /. m pparent Power onsumption open circuit Power Usage for TM with UPS Rated urrent onsumption (Maximum Operation 0-0 / 0-0 V pparent Power onsumption (Maximum Operation 0-0 / 0/0 V Real Output 0-0 V / 0-0 V Power factor Protection lass Leakage urrent (Maximum 0-0 V / 0-0 V Standby Power onsumption (no transaction Heating (without device Rated current consumption 0-0 V / 0-0 V pparent power consumption 0-0 V / 0-0 V ctive power 0-0 V / 0-0 V Finish Fascia painted standard WN Grey (option any NS or RL color or stainless steel Housing (Top over painted standard WN Grey (option any NS or RL color Safe painted standard Grey (option any NS or RL color Operating Environment (N EN 0(E Temperature, Safe location lass K (nside + to + ( to 9 F Relative Humidity (Non ondensing (nside to % Temperature, Fascia location (Outside with heating -0 to + 0 ( -0 to F Relative Humidity (Non ondensing (Outside to % Temperature, Limited range of Operation (inside, only a short time of Operation lass K + to +0 ( to 0 F Relative Humidity, Limited range of Operation (inside, only a short time of Operation lass K to % Transport lass K, Temperature - to + 0 (- to 0 F Transport lass K, Relative Humidity to 9 % Storage lass K, Temperature + to + 0 ( to 0 F Storage lass K, Relative Humidity to % Mechanical Environment (N EN 0(N E Operation Standalone Unit lass M Operation esktop Unit lass M Transport (n Original packing, on Vehicle, trailer, boat, train, and ir lass M Storage (n Original Packing lass M Environmental Protection (SN0 / / Environmental Protection (Recycling Noise emission in accordance with N EN 9 / Noise rating according to SO 99 Sound power level LWd Standby / Operation Work place specific Sound pressure level Lpm Standby / Operation. /. / 0 V / TU/h. /. m. /.9 00 / 0 V 9 / TU/h Proash 00xe / TN P / P 0. /. 0 / 0 V 9 / W 0.9 / 0.. /. m. /. / 0 V 9 / 0 W. /. m. /.9 00 / 0 V 00 / 0 W. /.0 d / d SPEFKTONS imensions and Weight of Unit without / rack Height Recommended nstallation Height Width epth epth with fascia frame (Wodden Support Table with Safe Weight Surface Load Foot print Operation and Maintenance rea (Front Load Operation and Maintenance rea (Rear Load Fan capacity Fore more etails regarding nstallation not covered in this document we refer to Reference nstallation Guide with order no.: 00090 GENERL SPEFKTONS Single able Run onstrains The following chart sitemizes the physical spacing requirements of the signal cable run with respect to order power and electrical equipment cable run. Type of electrical run Fluorescent, neon incandescent lighting fixture Unshielded power line or electrical equipment Unshielded power line or electrical equipment with signal cables enclosed in grounded conduit Power line in grounded conduit with signal cables in grounded conduit Single able nstallation onstrains Relative care is required when installing signal cables in conduits. Unlike power and lightening cables, signal cables have small conductors and light isolations and will not withstand as much strain in installation. The following chart summarizessome common conduit parameters. The sum of crosssectional areas of cables being installed in conduit should not exceed 0% of the area of the conduit. onduit size (inches / / / / nternal diameter (inches 0, 0,,09,,,0 rea square inches 00% For conduit runs. meters to 0. meters ( 0 to 00 feet, not more than % of conduit area should be used. Each 90 degree conduit bend may be estimated as equal to the friction of a 9. meters (0 foot length straight level conduit. f more than two 90 degree bends are used in conduit run, insert a pull box. Electro static discharge Static electricity charges are built up as a result of contact with certain floor covering and furniture. discharge of this build up can discomfort to people and possible interference with electronic devices. The following precautions should be taken whenever possible to reduce the chance of static discharge problems. void relative humidity values less than 0 %. Treat floor covering around electronic equipment with static reducing agents commercially available. UL 9 usiness UL 9 EN EN V 0, 0, 0,,,0, kg (0.99 lb.kn/m²(.lb/in² elow kv mm ( mm ( mm ( / 0, m² (.9 ft² 0 mm ( /.0 m² (. ft² 0m³/h(. ft³/h 0% 0, 0, 0, 0, 0,, 90 kg (9. lb 9.kN/m²(.lb/in² 0, m² (.9 ft² Power of electrical run etween - kv mm ( 0 mm ( mm ( mm (.0 m² (. ft² 0m³/h(. ft³/h % 0,099 0, 0, 0,9 0,9,09 Proash 00xe 00 mm (9.0 00 mm (. 0 mm (. 90 kg (9. lb 9.kN/m²(.lb/in² 0, m² (.9 ft².0 m² (. ft² 0m³/h(. ft³/h bove kv mm ( 0 mm ( - 0 0 mm ( mm ( % 0,0 0, 0, 0, 0, 0, External cabling Please refer to the appropriate TM nstallation Guide for details for terminal cable access. Junction boxes, conduit, etc, are the responsibility of the customer. Local codes will dictate location and material to be used in electrical connections. Negativ pressure constraints To prevent cold weather operating problems due to induction of outside air and accompanying incursion of dirt, TM should be housed in a positive pressure environment, however negative (vacuum not exceeding (.0" HO is acceptable. Tall buildings are especially prone to having negative pressure values greater than (.0" special engineering will be required if this specified pressure is exceeded Proash 00xe Version 0.

Proash 00xe tunnel width mm -." View of evice without illuminated signage Minimum Service rea (." 0 (." 00 (." 0 (.9" m a x.0 ( m a x.. " max. 0 (max.." 00 (9.0" 90 (." 00 (9.0" (." * Standard lock: mm (.9" ustomer-specific lock: mm (." rawings is not drawn to scale. ll emissions in Milimeter and (nches. Weight in Kilo and (Pound. ll imensions, Weight and esign, is /* (."/.9"* 00 (." (." (." (.9" 0 (." (.9". (0." (." (.9" 00 (9.9" (." (.9" (." 0 (." dditional installation space required to reach the Operation and maintenance space dditional operation and maintenance Wall 0 (." 0 (.9" (.9" 0 (0." 0. (.9" (0." 0 00 0 (." (." (." 90 (." 0 (." 0 (. " 9 (." 0 (.9" 9 (." (.9" (.9" (.9" (. " (. 9" Outside wall nside wall (device side x x 90 (." (." evice Wall Floor inside Floor outside Possible variants, and see down here Variant mm (0." > x < 9 mm (." Variant x = 0 (." Variant x > mm (." (." 0 (.9" 0 (." 9* (."* min. 0 (min.." min. X X (min..9" 0* (.09"* X x = x - (." Safe anking ivision Marketing Mounting set for safe Heinz-Nixdorf-Ring Tear-off sensor -0 Paderborn Screed 0 Phone +9(0/9 0 oncrete Fax +9(0/9 Mounting set for c ll Rights, including rights created by patent Top surface of finished floor 0 nstallation frame mm (." grant or registration of a utility model or design, nstallation rack 9 nstallation frame mm (0.9" elivery subject to availability, subject to min. 0 min. 0 (min.." (min.," 9 x = x - (." - (0.9" min. x = (." (min..9" 0* (.09"* min. * (0.9" (min..9"* x x Height-adjustable installation rack nstallation Frame mm (." (." (." (.9" (.0" (." (." (." (." 0 (." 00 (." (." 0 (.". (0." 0. (.0" 0 (." 0. (." max.0 (." (." (.0" 9 (." 99 (." (0.9" 9 (." (." (.9" 9 (.9" 9 (." (.9" 9 (." (9." 9 0 (.0". (." 0 (.". (0." 0. (." max.0 (." (.9" (." nstallation Frame mm (0.9" (.0" (." (." (0." (." 9 (.0" 0 (.09" (.9". (0." 9 (.9" 9 (." 9 (." 9 (.". (." 0 0 (." 0 (.9" 0. (." max.0 (." (.9" Proash 00xe Version 0.

Proash 00xe tunnel width mm -." View of evice with illuminated signage Minimum Service rea (9.0" (." 0 (.9" 0 (." 00 (." 0 (.9" m a x.0 ( m a x.. " max. 0 (max.." (." 90 (." 00 (9.0" (." * Standard lock: mm (.9" ustomer-specific lock: mm (." rawings is not drawn to scale. ll emissions in Milimeter and (nches. Weight in Kilo and (Pound. ll imensions, Weight and esign, is /* (."/.9"* 00 (." (.9" 0 (." (.9". (0." (." (." (.9" 00 (9.9" (." (." (.9" (." (." dditional installation space required to reach the Operation and maintenance space dditional operation and maintenance Wall 0 (." 0 (.9" (.9" 0 (0." 0. (.9" (0." 0 00 0 (." (." (." 90 (." 0 (." 0 (. " 9 (." 0 (.9" 9 (." 0 (." (.9" (. 9 " (.9" (. " (. 9 " Outside wall nside wall (device side x x 90 (." (." evice Wall Floor inside Floor outside Possible variants, and see down here Variant mm (0." > x < 9 mm (." Variant x = 0 (." Variant x > mm (." (." 0 (.9" 0 (." 9* (."* min. 0 (min.." min. X X (min..9" 0* (.09"* X x = x - (." Safe anking ivision Marketing Mounting set for safe Heinz-Nixdorf-Ring Tear-off sensor -0 Paderborn Screed Phone +9(0/9 0 oncrete Fax +9(0/9 Mounting set for c ll Rights, including rights created by patent Top surface of finished floor 0 nstallation frame mm (." grant or registration of a utility model or design, nstallation rack 9 nstallation frame mm (0.9" elivery subject to availability, subject to min. 0 0 min. 0 (min.." (min.," 9 x = x - (." - (0.9" min. x = (." (min..9" 0* (.09"* min. * (0.9" (min..9"* x x Height-adjustable installation rack nstallation Frame mm (." nstallation Frame mm (0.9" (." (." (.9" (.0" (." (." (." (." 0 (." 00 (." (." 0 (.". (0." 0. (.0" 0 (." 0. (." max.0 (." (." (.0" 9 (." 99 (." (0.9" 9 (." (." (.9" 9 (.9" 9 (." (.9" 9 (." (9." 9 0 (.0". (." 0 (.". (0." 0. (." max.0 (." (.9" (." (.0" (." (." (0." (." 9 (.0" 0 (.09" (.9". (0." 9 (.9" 9 (." 9 (." 9 (.". (." 0 0 (." 0 (.9" 0. (." max.0 (." (.9" Proash 00xe Version 0.

Proash 00xe tunnel width mm -." View of evice with upper and lower illuminated signage Minimum Service rea (9.0" (." 0 (.9" 0 (." 00 (." 0 (.9" m a x.0 ( m a x.. " max. 0 (max.." (." 90 (." 00 (9.0" (." * Standard lock: mm (.9" ustomer-specific lock: mm (." rawings is not drawn to scale. ll emissions in Milimeter and (nches. Weight in Kilo and (Pound. ll imensions, Weight and esign, is /* (."/.9"* 00 (." (.9" 0 (." (.9". (0." (." (." 00 (9.9" (." (.9" (." 9 (.9" (.9" (." dditional installation space required to reach the Operation and maintenance space dditional operation and maintenance Wall 0 (." 0 (.9" (.9" 0 (0." 0. (.9" (0." 0 00 0 (." (." (." 90 (." 0 (." 0 (. " 0 (.9" 9 (." (.9" 9 (." 0 (." (." (.9" (. 9" (. " (. 9" Outside wall nside wall (device side x x 90 (." (." evice Wall Floor inside Floor outside Possible variants, and see down here Variant mm (0." > x < 9 mm (." Variant x = 0 (." Variant x > mm (." (." 0 (.9" 0 (." 9* (."* min. 0 (min.." min. X X (min..9" 0* (.09"* X x = x - (." Safe anking ivision Marketing Mounting set for safe Heinz-Nixdorf-Ring Tear-off sensor -0 Paderborn Screed Phone +9(0/9 0 oncrete Fax +9(0/9 Mounting set for c ll Rights, including rights created by patent Top surface of finished floor 0 nstallation frame mm (." grant or registration of a utility model or design, nstallation rack 9 nstallation frame mm (0.9" elivery subject to availability, subject to min. 0 0 min. 0 (min.." (min.," 9 x = x - (." - (0.9" min. x = (." (min..9" 0* (.09"* min. * (0.9" (min..9"* x x Height-adjustable installation rack nstallation Frame mm (." nstallation Frame mm (0.9" (." (." (.9" (.0" (." (." (." (." 0 (." 00 (." (." 0 (.". (0." 0. (.0" 0 (." 0. (." max.0 (." (." (.0" 9 (." 99 (." (0.9" 9 (." (." (.9" 9 (.9" 9 (." (.9" 9 (." (9." 9 0 (.0". (." 0 (.". (0." 0. (." max.0 (." (.9" (." (.0" (." (." (0." (." 9 (.0" 0 (.09" (.9". (0." 9 (.9" 9 (." 9 (." 9 (.". (." 0 0 (." 0 (.9" 0. (." max.0 (." (.9" Proash 00xe Version 0.

Proash 00xe tunnel width 0 mm -." View of evice without illuminated signage Minimum Service rea (." 0 (." 00 (." 0 (.9" ma x. ( m a x.. 9 " max. 0 (max.." 00 (9.0" 90 (." 00 (9.0" (." /* (."/.9"* * Standard lock: mm (.9" ustomer-specific lock: mm (." rawings is not drawn to scale. ll emissions in Milimeter and (nches. Weight in Kilo and (Pound. ll imensions, Weight and esign, is 00 (." (.9" (." (.9". (0." (." (." (." (.9" 00 (9.9" 0 (." (.9" (." (." dditional installation space required to reach the Operation and maintenance space dditional operation and maintenance Wall 0 (." 0 (.9" (.9" 0 (0." 0. (.9" (0." 0 00 0 (." (." (." 90 (." (." 0 (. " 0 (." 9 (." 0 (.9" (.9" (." (.9" 0 (. " Outside wall nside wall (device side x x 90 (." (." evice Wall Floor inside Floor outside Possible variants, and see down here Variant mm (0." > x < 9 mm (." Variant x = 0 (." Variant x > mm (." (." 0 (.9" 0 (." 9* (."* min. 0 (min.." min. X X (min..9" 0* (.09"* X x = x - (." Safe anking ivision Marketing Mounting set for safe Heinz-Nixdorf-Ring Tear-off sensor -0 Paderborn Screed Phone +9(0/9 0 oncrete Fax +9(0/9 Mounting set for c ll Rights, including rights created by patent Top surface of finished floor 0 nstallation frame mm (." grant or registration of a utility model or design, nstallation rack 9 nstallation frame mm (0.9" elivery subject to availability, subject to min. 0 0 min. 0 (min.." (min.," 9 x = x - (." - (0.9" min. x = (." (min..9" 0* (.09"* min. * (0.9" (min..9"* x x Height-adjustable installation rack nstallation Frame mm (." nstallation Frame mm (0.9" (." (." (.9" (.0" (." (." (." (." 0 (." 00 (." (." 0 (.". (0." 0. (.0" 0 (." 0. (." max. (.9" (." (.0" 9 (." 99 (." (0.9" 9 (." (." (.9" 9 (.9" 9 (." (.9" 9 (." (9." 9 0 (.0". (." 0 (.". (0." 0. (." max. (.9" (." (." (.0" (." (." (0." (." 9 (.0" 0 (.09" (.9". (0." 9 (.9" 9 (." 9 (." 9 (.". (." 0 0 (." 0 (.9" 0. (." max. (.9" (." Proash 00xe Version 0.

Proash 00xe tunnel width 0 mm -." View of evice with illuminated signage Minimum Service rea (9.0" (." (.9" 0 (." 00 (." 0 (.9" ma x. ( m a x.. 9 " max. 0 (max.." 0 (." 90 (." 00 (9.0" (." * Standard lock: mm (.9" ustomer-specific lock: mm (." rawings is not drawn to scale. ll emissions in Milimeter and (nches. Weight in Kilo and (Pound. ll imensions, Weight and esign, is /* (."/.9"* 00 (." (.9" (." (.9". (0." (." (." (." (.9" 00 (9.9" 0 (." (.9" (." 0 (." dditional installation space required to reach the Operation and maintenance space dditional operation and maintenance Wall 0 (." 0 (.9" (.9" 0 (0." 0. (.9" (0." 0 00 0 (." (." (." 90 (." (." 0 (. " 9 (." 0 (.9" 9 (." 0 (." (.9" (." (.9 " (. 9 " 0 (. " Outside wall nside wall (device side x x 90 (." (." evice Wall Floor inside Floor outside Possible variants, and see down here Variant mm (0." > x < 9 mm (." Variant x = 0 (." Variant x > mm (." (." 0 (.9" 0 (." 9* (."* min. 0 (min.." min. X X (min..9" 0* (.09"* X x = x - (." Safe anking ivision Marketing Mounting set for safe Heinz-Nixdorf-Ring Tear-off sensor -0 Paderborn Screed Phone +9(0/9 0 oncrete Fax +9(0/9 Mounting set for c ll Rights, including rights created by patent Top surface of finished floor 0 nstallation frame mm (." grant or registration of a utility model or design, nstallation rack 9 nstallation frame mm (0.9" elivery subject to availability, subject to min. 0 0 min. 0 (min.." (min.," 9 x = x - (." - (0.9" min. x = (." (min..9" 0* (.09"* min. * (0.9" (min..9"* x x Height-adjustable installation rack nstallation Frame mm (." nstallation Frame mm (0.9" (." (." (.9" (.0" (." (." (." (." 0 (." 00 (." (." 0 (.". (0." 0. (.0" 0 (." 0. (." max. (.9" (." (.0" 9 (." 99 (." (0.9" 9 (." (." (.9" 9 (.9" 9 (." (.9" 9 (." (9." 9 0 (.0". (." 0 (.". (0." 0. (." max. (.9" (." (." (.0" (." (." (0." (." 9 (.0" 0 (.09" (.9". (0." 9 (.9" 9 (." 9 (." 9 (.". (." 0 0 (." 0 (.9" 0. (." max. (.9" (." Proash 00xe Version 0.