INTRODUCTION GENERL DESCRIPTION Ducted Direct Drive Fan Coil ir Conditioners are designed to fulfill the air conditioning requirements of today s living. These requirements include dependable trouble-free operation where units will be installed above ceilings and hallways and in closets; compact spacesaving design to allow more valuable living space; and the quiet performance affordable by a centrally-located unit that is ducted to individual rooms. lthough primarily intended for apartment markets, these versatile units can also be used in low static pressure applications where ducted units are needed. UNIT NOMENCLTURE The model number denotes the following characteristics of the unit : CP 06 F C - 4 L - F DUCTED CONCELED WITH PLENUM F - c/w Filter SIZE Nominal ir Flow () 06 600 08 800 0 000 00 4 400 6 600 8 800 0 000 GENERTION F F Series VOLTGE CODE 0~40V-Ph-50/60Hz CONNECTION LH : Left Hand RH : Right Hand ROWS OF 3 : Three Rows 4 : Four Rows 6 : Six Rows FIN TYPE : luminium H : Hydrophillic C : Copper Những điều kỳ lạ ng DESIGN PRMETER VOLTGE CODE UNIT POWER MINIMUM VOLTGE MXIMUM VOLTGE C 0~40V-Ph-50/60Hz 0 40
INTRODUCTION BSIC UNIT ND CBINET The basic unit is fabricated out of galvanized steel. The return plenum, fan deck and the top of the coil section shall be lined with 6mm coated Polyethylene Foam. Fan motor(s) are easily removable for serviceability with a terminal box with terminal strip fitted for wiring. Filter media is G as a standard and for units with plenum, filters can be conveniently removed from either the side or the back. The CDCP series cooling coil is made of corrugated aluminum fins which are mechanically bonded to the copper tubes. The fins have a maximum fin spacing of.mm in between to prevent any moisture carry over and to provide the sufficient cooling capacity without compromising the right airflow. Coils shall be factory leak tested at 350psig (400kPa) and suitable for working pressure up to 50psig (700kPa). DRIVE PCKGE CDCP series motors are specified to have 3 speed permanently split capacitor. Motors have permanently lubricated ball bearings and class B insulation. Standard motor provided are IP0 rated. The fan(s) are centrifugal forward curved type fan which are statically and dynamically balanced. DRIN PN Electro-Galvanized (EG) drain pans for the CDCP are oven-baked polyester powder coated with its external surface insulated with 5mm PE foam (fire class rated). OPTIONL FETURES iết! Hydrophilic or Copper fin coil 3 rows / 4 rows cooling coil + row heating coil Thermostat Electrical Fin Heater FILTER Spare set filter Return Grille (Double) Nominal " l-mesh G Filter Nominal " washable G3 Filter CSING Stainless steel casing Double insulation (0mm insulation) Extended drain pan Powder coating casing SS Drain Pan SS Extended Drain Pan Supply Grille (Double) Double skin PU panel (7mm / 5mm / 50mm)
INTRODUCTION BSIC UNIT ND CBINET The basic unit is fabricated out of galvanized steel. The return plenum, fan deck and the top of the coil section shall be lined with 6mm coated Polyethylene Foam. Fan motor(s) are easily removable for serviceability with a terminal box with terminal strip fitted for wiring. Filter media is G as a standard and for units with plenum, filters can be conveniently removed from either the side or the back. The CDCP series cooling coil is made of corrugated aluminum fins which are mechanically bonded to the copper tubes. The fins have a maximum fin spacing of.mm in between to prevent any moisture carry over and to provide the sufficient cooling capacity without compromising the right airflow. Coils shall be factory leak tested at 350psig (400kPa) and suitable for working pressure up to 50psig (700kPa). DRIVE PCKGE CDCP series motors are specified to have 3 speed permanently split capacitor. Motors have permanently lubricated ball bearings and class B insulation. Standard motor provided are IP0 rated. The fan(s) are centrifugal forward curved type fan which are statically and dynamically balanced. DRIN PN Electro-Galvanized (EG) drain pans for the CDCP are oven-baked polyester powder coated with its external surface insulated with 5mm PE foam (fire class rated). OPTIONL FETURES Hydrophilic or Copper fin coil 3 rows / 4 rows cooling coil + row heating coil Thermostat Electrical Fin Heater FILTER Spare set filter Return Grille (Double) Nominal " l-mesh G Filter Nominal " washable G3 Filter CSING Stainless steel casing Double insulation (0mm insulation) Extended drain pan Powder coating casing SS Drain Pan SS Extended Drain Pan Supply Grille (Double) Double skin PU panel (7mm / 5mm / 50mm)
PHYSICL DT DCP-F Physical Data 3 Row Coil Nominal irflow Total Cooling Capacity Water Flow Rate Water Pressure Drop Tube Thickness / Fin Thickness Number of Rows / FPI Tube Size Face rea Coil Static Resistance Max. Working Pressure Testing Pressure Connection (Copper Tube) Header MOTOR Power Supply Number of Motor Rating Output (per unit motor) Max. Running mp (40V/Ph/50Hz) (per unit motor) Poles FN / Drive Blower Size (Qty) FRME Casing Insulation DRIN PN Material Finishing Connection FILTER Filter Qty / Unit Nominal Size (per unit filter) ctual Size (per unit filter) OVERLL DIMENSION Depth Width Height Estimated Unit Weight High Medium Low ton MBH kwr USgpm l/s ft.wg kpa mm / mm ft² m² in.wg (Pa) V / Ph / Hz Qty Watt in mm kg 06 08 0 4 6 8 0 788 340 784 33 704 97.6 9.6 5.8 3. 0.0 5.4 6.5.35 0.3 0.40 (00) Seamless Copper Tube / Corrugated luminium Fin 0.30 / 0.5 3 / 3/8 " O.D..87.50.7 3.0 3.9 3.9 0.7 0.3 0.5 0.8 0.36 0.36 0.30 (76) 0.9 (7) 0.34 (84) 0.9 (73) 0. (56) 0. (54) 50 (700) 350 (400) 7/8" O.D. - /8" O.D. Copper Pipe 4.06 0.38 0. (56) 3-Speed Permanent Split Capacitor Motor 0-40 / / 50 35 35 50 35 35 50 50 50.3.3.5.3.3.5.5.5 Centrifugal Fan (Forward-Curved Steel Fan Wheels) / Direct Motor Driven DD9x7 () DD9x9 () DD9x9 () DD9x7 () DD9x7 () DD9x9 () DD9x9 () DD9x9 () 3*0 340*50 9. (738) 35 909 546 89 54 763 98. 5. 7.4 4.8 0.30 9.90 9.69 3*5 340*650 34. (8) 40 077 83 039 765 98 578.6 30.7 9.0 6.3 0.40 5.7 47. 483 5 366 3 45 7 3. 37.9. 7.9 0.50 9.6 7.78 6 64 76 476 508 9 96 3.6 43.3.7 7.9 0.50.98 38. Galvanized Steel Polyethylene Foam : 6mm 6 759 459 479 303 6 3.9 46.4 3.6 9.5 0.60 6.7 48.50 Electro-Galvanized Steel Epoxy Polyester Powder Coating - /4" O.D. Steel Pipe Non Threaded 64 7 63 74 484 54 4.4 5.6 5.4. 0.70.0 66.06 Nominal " Washable Filter (75~80% rrestance) 3*9 340*750 3*35 340*880 3*0 340*505 3* 340*565 3*5 340*630 38. (968) 43 4.3 (098) 58 48.3 (8) 63 53. (348) 67 58. (478) 7 843 334 79 3043 640 789 4.9 58.4 7.. 0.70 8.35 85.04 3*6 340*680 6. (578) 73 NOTES Cooling Capacity irflow :- The performances are based on the following conditions: : - Entering air temperature = 80ºF (6.7ºC) DB, 67ºF (9.4ºC) WB - Entering chilled water temperature = 44ºF (6.7ºC) - Leaving chilled water temperature = 54ºF (.ºC) : - Medium fan speed - 40V-Ph-50Hz power supply - Under dry coil condition at 0.in.WG (50Pa) external static pressure - Unit with filter(s) 3
PHYSICL DT DCP-F Physical Data 4 Row Coil Nominal irflow Total Cooling Capacity Water Flow Rate Water Pressure Drop Tube Thickness / Fin Thickness Number of Rows / FPI Tube Size Face rea Coil Static Resistance Max. Working Pressure Testing Pressure Connection (Copper Tube) Header MOTOR Power Supply Number of Motor Rating Output (per unit motor) Max. Running mp (40V/Ph/50Hz) (per unit motor) Poles FN / Drive Blower Size (Qty) FRME Casing Insulation DRIN PN Material Finishing Connection FILTER Filter Qty / Unit Nominal Size (per unit filter) ctual Size (per unit filter) OVERLL DIMENSION Depth Width Height Estimated Unit Weight High Medium Low ton MBH kwr USgpm l/s ft.wg kpa mm / mm ft² m² in.wg (Pa) V / Ph / Hz Qty Watt in mm kg 06 08 0 4 6 8 0 665 3 66 3 589 00.8.7 6.4 4.8 0.30 4.68 4.03 87 407 80 363 67 43.4 8.6 8.4 6.3 0.40 8. 6.79 957 68 4 587 80 395.9 34.5 0. 6.3 0.40 3.9 4.77 30 8 76 998 045 777 3.4 4.0.0 7.9 0.50 6.9 8. 403 3 60 4 9 903 3.9 46.5 3.6 9.5 0.60 8.73 6.0 456 476 306 9 43 944 4.3 5. 5.0 9.5 0.60.38 34.5 484 54 478 5 30 45 4.9 58.3 7.. 0.70 5.69 47.06 64 745 605 77 455 475 5.3 64. 8.8.7 0.80 9.85 59.55.35 0.3 0.40 (99) 35.3.87 0.7 0.34 (84) 35.3 Seamless Copper Tube / Corrugated luminium Fin 0.30 / 0.5 4 / 3/8" O.D..50.7 3.0 3.9 3.9 0.3 0.5 0.8 0.36 0.36 0.3 (80) 0.34 () 0.9 (73) 0.5 (6) 0.5 (6) 50 (700) 350 (400) - /8" O.D. Copper Pipe 3-Speed Permanent Split Capacitor Motor 50.5 0-40 / / 50 35 35.3.3 50.5 50.5 4.06 0.38 0.4 (6) 50 Centrifugal Fan (Forward-Curved Steel Fan Wheels) / Direct Motor Driven DD9x7 () DD9x9 () DD9x9 () DD9x7 () DD9x7 () DD9x9 () DD9x9 () DD9x9 () 3*0 340*50 9. (738) 37 3*5 340*650 34. (8) 43 6 Galvanized Steel Polyethylene Foam : 6mm Electro-Galvanized Steel Epoxy Polyester Powder Coating -/4" O.D. Steel Pipe Non Threaded Nominal " Washable Filter (75~80% rrestance) 3*9 340*750 3*35 340*880 3*0 340*505 3* 340*565 38. (968) 45 4.3 (098) 6 48.3 (8) 67 53. (348) 70 3*5 340*630 58. (478) 75.5 3*6 340*680 6. (578) 79 NOTES Cooling Capacity irflow :- The performances are based on the following conditions: : - Entering air temperature = 80ºF (6.7ºC) DB, 67ºF (9.4ºC) WB - Entering chilled water temperature = 44ºF (6.7ºC) - Leaving chilled water temperature = 54ºF (.ºC) : - Medium fan speed - 40V-Ph-50Hz power supply - Under dry coil condition at 0.in.WG (50Pa) external static pressure - Unit with filter(s) 4
PHYSICL DT DCP-F Physical Data 6 Row Coil Nominal irflow Total Cooling Capacity Water Flow Rate Water Pressure Drop Tube Thickness / Fin Thickness Number of Rows / FPI Tube Size Face rea Coil Static Resistance Max. Working Pressure Testing Pressure Connection (Copper Tube) Header MOTOR Power Supply Number of Motor Rating Output (per unit motor) Max. Running mp (40V/Ph/50Hz) (per unit motor) Poles FN / Drive Blower Size (Qty) FRME Casing Insulation DRIN PN Material Finishing Connection FILTER Filter Qty / Unit Nominal Size (per unit filter) ctual Size (per unit filter) OVERLL DIMENSION Depth Width Height Estimated Unit Weight High Medium Low ton MBH kwr USgpm l/s ft.wg kpa mm / mm ft² m² in.wg (Pa) V / Ph / Hz Qty Watt in mm kg 06 08 0 4 6 8 0 474 806 467 794 398 677.7 0.8 6. 4.8 0.30.68 5.05 69 070 607 069 50 854.4 8. 8.3 6.3 0.40 3.4 0.3 7 70 607 03.8 34. 0.0 6.3 0.40 5.33 5.98 9 677 89 39 696 84 3. 38.7.3 7.9 0.50.69 8.06 08 73 887 507 739 57 3.6 43.5.7 9.5 0.60 3.68.03 089 85 960 63 405 4.0 48.0 4. 9.5 0.60 4.83 4.49 50 956 3 9 998 697 4.8 57. 6.8. 0.70 7..65 9 073 78 00 046 779 5. 60.7 7.8.7 0.80 8.58 5.73.35 0.3 0.3 (8) 35.3 Seamless Copper Tube / Corrugated luminium Fin 0.30 / 0.5 6 / 3/8" O.D..87.50.7 3.0 3.9 3.9 0.7 0.3 0.5 0.8 0.36 0.36 0.3 (78) 0.9 (73) 0.8 (69) 0.4 (60) 0. (54) 0.3 (58) 50 (700) 350 (400) - /8" O.D. - 3/8" O.D. Copper Pipe 35.3 3-Speed Permanent Split Capacitor Motor 50.5 0-40 / / 50 35 35.3.3 50.5 50.5 4.06 0.38 0. (54) 50 Centrifugal Fan (Forward-Curved Steel Fan Wheels) / Direct Motor Driven DD9x7() DD9x9() DD9x9() DD9x7() DD9x7() DD9x9() DD9x9() DD9x9() 3*0 340*50 9. (738) 39 3*5 340*650 34. (8) 44 6 Galvanized Steel Polyethylene Foam : 6mm Electro-Galvanized Steel Epoxy Polyester Powder Coating -/4" O.D. Steel Pipe Non Threaded Nominal " Washable Filter (75~80% rrestance) 3*9 340*750 3*35 340*880 3*0 340*505 3* 340*565 38. (968) 49 4.3 (098) 65 48.3 (8) 69 53. (348) 75 3*5 340*630 58. (478) 8.5 3*6 340*680 6. (578) 83 NOTES Cooling Capacity irflow : - The performances are based on the following conditions: : - Entering air temperature = 80ºF (6.7ºC) DB, 67ºF (9.4ºC) WB - Entering chilled water temperature = 44ºF (6.7ºC) - Leaving chilled water temperature = 54ºF (.ºC) : - Medium fan speed - 40V-Ph-50Hz power supply - Under dry coil condition at 0.in.WG (50Pa) external static pressure - Unit with filter(s) 5
SHOPFLOOR DIMENSIONS DCP 06 0FC Shopfloor (Single Skin) B 3 H G I 375 J 0 7 CONNECTION LOCTION SLOTS ø*. (6) C D TOP VIEW 83 53 3 E 44 30 33 SIDE VIEW 70 F FRONT VIEW 7
SHOPFLOOR DIMENSIONS DCP 0FC Shopfloor (Single Skin) B 3 H G I 375 J 0 7 CONNECTION LOCTION SLOTS ø*. (6) C D TOP VIEW 83 53 3 E 44 30 33 70 F SIDE VIEW FRONT VIEW CONNECTION DIMENSIONS B C D E F ROW CHW. In/Outlet G H I J DCP 06FC 568 55 47 470 68 66 DCP 06-0FC DCP -0FC 3 3/4" BSPT " BSPT 44 4 96 DCP 08FC DCP 0FC 698 798 655 755 557 657 600 700 748 848 746 846 DCP 06-0FC DCP 06-0FC DCP -0FC 4 6 " BSPT -/4" BSPT 84 66 0 5 DCP FC DCP 4FC DCP 6FC 98 058 78 885 05 35 787 97 037 830 960 080 978 08 8 976 06 6 DCP 8FC 308 65 67 0 358 356 DCP 0FC 408 365 67 30 458 456 8
Double Skin 7MMDS 5MMDS 50MMDS DCP 06 DCP 08 DCP 0 DCP DCP 4 DCP 6 DCP 8 DCP 0 DCP 06 DCP 08 DCP 0 DCP DCP 4 DCP 6 DCP 8 DCP 0 DCP 06 DCP 08 DCP 0 DCP DCP 4 DCP 6 DCP 8 DCP 0 956 095 3 384 470 64 76 8 956 095 3 384 470 64 76 8 956 095 3 384 470 64 76 8 B 906 045 63 334 40 59 676 76 906 045 63 334 40 59 676 76 906 045 63 334 40 59 676 76 C 9 9 9 9 9 9 9 9 D 80 80 80 80 80 80 80 80 8 8 8 8 8 8 8 8 E 643 84 070 56 37 4 498 659 830 95 0 7 343 48 54 709 880 36 3 478 564 F 496 63 63 95 988 9 46 46 496 63 63 95 988 9 46 46 496 63 63 95 988 9 46 46 G 533 704 789 960 046 7 30 388 5 6 778 949 035 06 9 377 5 6 778 949 035 06 9 377 H 47 47 47 47 47 47 47 47 I 36 36 36 36 36 36 36 36 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 J K 9 9 9 9 9 9 9 9 L 95 95 95 95 95 95 95 95 M 48 48 48 48 48 48 48 48 56 56 56 56 56 56 56 56 8 8 8 8 8 8 8 8 DIMENSIONS IN MM SHOPFLOOR DIMENSIONS 0
* While utmost care is taken in ensuring that all details in the publication are correct at the time of going to press, we are constantly striving for improvement and therefore please confirm with your local distribution office for the latest update on the product interested. ll rights reserved.