RTR KITS - REQUIRED FOR OPERATION

Strong Front and Rear chassis braces. Tuned Polished Dual Chamber racing pipe. Unique adjustable chassis width of 310mm or 330mm. High performance.26 engine with Shaft Start Motor handle. Full race Offset King Pin aluminum steering knuckle. Three sealed differentials with 6 steel gears. Racing X-Equal tires and V-spoke wheels. Adjustable Front and Rear roll bars. Multi disc brakes with adjustable bias. Hard Coated Threaded body oil fill shocks. 5 Degree hard coated 3mm chassis. Racing 3 shoe clutch with Aluminum CNC flywheel. Steel main spur gear and center differential. Adjustable servo saver. Front CVA joint and 8mm axles. 140+cc fuel tank with inside stone filter. INSTRUCTION MANUAL

THINGS NEEDED RTR KITS - REQUIRED FOR OPERATION You will need to buy a few items to start the engine and run the car. Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat engine. Buy LONG glow plugs, like OFNA/PICCO Plug (#51007 or 51008). Use plugs without idle bar. Do NOT use plugs, like the MC-59 or OS-8 In your box you will find.. #10163 - Bottle, spout top #10219 - Red D size glow heater Glow Fuel 20% AA Batteries ( 12 pcs ) #10212 NiHm Hump Pack, see charger 10214. You need to get batteries for the radio transmitter and the car receiver packs. Radio TX needs (8) eight AA batteries. Car needs (4) four AA Ni-cad batteries 2000Mah OFNA #10196 or (4) Alkaline., Alkaline type batteries will work, but braking will be reduced and 30 minute life. The best for car, is to use a 5 cell hump receiver pack for increased voltage and longer life.. Recommended Option: You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell type(600ae). This will give more run time. OFNA #10212 1200NiMh Hump Pack and 10214 NiHm Battery Charger #10214 Over-nite Charger TOOLS NOT INCLUDED IN KIT, BUT NEEDED TO MAINTAIN YOUR CAR. Cutter Instant Cement Phillips Type Drivers ( L ) Curved Scissors #91009 $5.95 Grease Phillips Type Drivers ( S ) Cross Wrench #17109 $3.95 Needle Nose Pliers Knife Glow Plug & 17MM Cross Wrench #10801 $6.95

MUST READ THIS BEFORE RUNNING Running a nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful. Where to run car? Any running area you choose must be dry. Do not run car near any water or wet dirt. Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb. Do not operate car in tight confined places. The car is very fast and will easily hit something. Do not run near people or animals. The car is very fast and will too easily hit someone. Due noise, you will want to consider the surrounding area when operating the car. Do not operate the car at night. You will not be able to drive it without hitting something. Do not operate the car indoors. Engine exhaust is not healthy. Glow Fuel Glow fuel is poisonous! Glow fuel is flammable! Do not leave in fuel bottle with lid off at any time. Do not use any fuel other than glow fuel in this engine. First Time Starting the Engine Caution! When starting engine make sure the following is observed. Set engine Master needle to 3 turns (rich setting) Do not do this alone, get an experienced friend to help at first. Fill fuel tank, try not to spill fuel. Do not spill fuel on receiver Hold car off the ground, so it will not runaway when first starts Turn on Radio and check the linkage before starting engine. Turn on car receiver battery switch. Always have an air filter on the carburetor to keep dirt out. Engine Break-in See Engine Page. Emergency Stopping Engine When Running Remove air filter and cover carb. intake. Squeeze fuel line and hold until engine stops. With a rag, cover exhaust outlet. Clean oil and dirt from chassis with a degreaser. Precautions This kit is not a toy. Always run car with a second person as a spotter and pitman. Hot Parts - The pipe, manifold, engine and head are very hot and will cause burns. Rotating Parts - Keep hands away from the drive train, wheels, and engine when engine is running. Radio - Check batteries life before running the car. If radio does not have full control of the car with steering and/or throttle/brake do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property. Glow fuel - Do leave the glow fuel unattended with the lid off. Fuel contains Methanol and Nitro Methane and is flammable and poisonous. Store fuel in cool ventilated location. Refer the glow fuel label for additional precautions. Car Fuel tank - Never store fuel in car tank, it will ruin the engine if left in tank. Always turn off the car BEFORE turning off radio. DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY ISSUE. IF YOU DO NOT BREAK-IN ENGINE CORRECTLY, MAINLY AT LOW RPM, YOU WILL BREAK THE CONNECTING ROD! FAILURE TO NOT READ AND FOLLOW BREAK-IN ENGINE INSTRUCTIONS WILL VOID WARRANTY! Storing Car After Running Remove fuel from tank and fuel lines Turn off radio in car Put a few drops of after run in engine to keep it from rusting.

NON-RTR OR PRO KITS - REQUIRED FOR OPERATION THINGS NEED BESIDES THE KIT 3.5 cc (21 Class) ENGINE REAR EXHAUST OFNA/Picco O-1 bp #51217 Glow Fuel 20% Glow Plug Heat with Battery & Charger # 10227...$$19.95 (please note OFNA Glow Heats available) Bottle s with spout # 10160 - large 500cc # 10161 - large 500 ccauto Stop # 10162 - small 250cc # 10164 - CNC spout 500CC # 10167 - CNC spout 800CC Note: Pro kit does not include engine! Off-Road Starter Box, 12V motor # 10250-1/8 scale Starter Box # 10253-1/8 scale Starter Box w/ Panel Off-Road Starter Box, two 550 motors # 10248-1/8 scale Starter Box # 10249-1/8 scale Starter Box,RTR Optional Parts # 92571 - Power Panel Glow Heater # 92572 - Cable for Glow Plug 12V Battery for Starter Box (must have) AA Batteries ( 12 pcs ) for radio RADIO CONTROL UNIT Note: Carefully read the instruction manual of your 2 channel radio controller before using. SUITABLE SERVO SIZE 36mm-41mm 15mm - 21mm 29mm - 42mm Radio must be set at neutral position before installing in the kit. SEQUENCE TO SET NEUTRAL Install AA batteries in Radio. Extend the antenna.(transmitter) Install batteries into Car receiver. After installing the battery, connect the battery box. Extend the antenna. (Receiver) Set the trim-lever at center. Turn on the switch. (Transmitter) Turn on the switch. (Receiver) Make sure the servos are in command. When the operation stick is in neutral, servo horns must be in neutral as will. *Adjustment can be made by reinstalling the servo horn. Turn off the switch. (Receiver) 11 Turn off the switch. (Transmitter) 12 Retract the antenna. (Transmitter) 13 More Optional Parts... #10211 NiHm Battery Flat Pack.. $29.95 # 10214 NiHm Battery Pack Charger.. $7.95 # 51007 or 08 OFNA/Picoo Glow Plug.. $4.95 TOOLS NOT INCLUDED IN KIT INCLUDED WITH KIT Cutter Instant Cement Shock Oil Phillips Type Drivers ( L ) Grease Box Curved Scissors Masking Tape 5mm Hex Wrench Phillips Type Drivers ( S ) Brush Cross Wrench #17109 $3.95 3mm Hex Wrench 2.5mm Hex Wrench Needle Nose Pliers Paints 1.5mm Hex Wrench Knife Glow Plug & 17MM Cross Wrench #10801 $6.95 Grease 7mm and 5.5mm Hex Wrench

40017 GEAR BOX PLASTIC PARTS PLASTIC PARTS 40003 DIFF. CASE PLASTIC PARTS 40015 ARM HOLDER PLASTIC PARTS 2 1 3 40027 WING SUPPORT PLASTIC PARTS 40013 & 40048 FRONT BUMPER & BATTERY HOLDER PLASTIC PARTS

40031 SERVO SAVER PLASTIC PARTS PLASTIC PARTS 40047 RECEIVER BOX PLASTIC PARTS 40040 CENTER DIFF. MOUNT PLASTIC PARTS 40018/40029 CHASSIS BRACE PLASTIC PARTS 40046 STONE GUARD PLASTIC PARTS 40029 40029 40065 40019 40065 40018 40056 SHOCK ABSORBER PLASTIC PARTS

ASSEMBLY OF THE THROTTLE LINKAGE SYSTEM #30800 Plastic Throttle kit 3X3mm Set 2mm Rod #30530 Plastic Throttle Ball Joint * Snap On. 3X3mm Set Throttle Spring Plastic Collar 3X3mm Set #10300 Alum.Stopper Fuel Tube ( 6mm ) #10300 Alum.Stopper * Align throttle servo same as shown. * Take the plastic collar from brake system plastic parts. Brake Idle Position Note: Battery life is short when using Alkaline batteries. For safety, we recommend using Alkaline batteries for only 30 minutes before testing.. Battery strength affects braking power and radio range. If voltage drops while running the car, you will loose control and destroy your car! This is NOT covered under warranty. Full Throttle To increase run time, upgrade receiver battery to a 5-cell hump pack. But, the most important step you can make, is to always use fully charged or fresh batteries when running your car. Another choice is to use OFNA #10196 2000 mah NiMh AA batteries in car and radio. CHECKING ENGINE THROTTLE 1. Insert AA batteries into transmitter (8 Pcs). 2.Turn on transmitter. 3.Turn on receiver. 4.Center throttle trims as shown. A B C 1. Pull Full Throttle. 1. Push trigger to full brake position. 2. Adjust alum. Stopper to increase or decrease the brake. * Align throttle servo same as shown. A Idle Position (A) Brake (C) IMPORTANT CHECK RADIO THROTTLE AND STEERING SWITCHES BEFORE RUNNING CAR * Insert into transmitter. Full Throttle (B) Full throttle arm position. Spring rod pulls throttle barrel open and brake rods release pressure on brake cams. B B A C C Full brake arm position. Spring compresses forward and brake rods pull brake levers.

ASSEMBLY OF THE DIFFERENTIAL GEAR 40006 Cap Joint 4x4mm Set 40010 2.5x13.8mm Pin 30779 4 x 10mm washer 40004 30773 Diff. Gear 4mm (Small) Cross pin 30779 4 x 10mm 40004 washer Diff. Gear (Small) 40003 Diff. Case 36053 8x16mm Ball bearing (Builds one differential for Center) 40005 Break Cap Joint 4x4mm Set 40010 2.5x13.8mm Pin 40009 P6 O-Ring 40004 Diff. Gear (Large) 40012 6x15mm Washer 40004 Diff. Gear 30779 (Small) 4 x 10mm washer 30773 4mm Cross pin 40004 Diff. Gear (Small) 30779 4 x 10mm washer Note: It is very important to add or remove the #30779 washer if the gear mesh is too tight or too lose. 36053 8x16mm Ball bearing OPTION: #49001 HD STEEL GEAR SET, INSIDE DIFF. 40003 Diff. Case 40009 P6 O-Ring 40012 6x15mm Washer 40004 Diff. Gear (Large) * Apply diff. gear grease to the differential during assembly. * Fill the diff. the case to approx 70% with grease. ASSEMBLY OF THE DIFFERENTIAL CASE 40004 Diff. Gear (Large) 40012 6x15mm Washer *Use 6x15mm washer to adjust the gear mesh. 40010 2.5x13.8mm Pin ( Builds two differentials for front and rear.) 40009 P6 O-Ring 40002 41T Large Bevel Gear 49032 41T Large HD Bevel Gear 36053 8x16mm Ball bearing 40006 Cap Joint 40011 Diff. Gasket OPTION: 49032 43T Large Bevel Gear (must use 13t pinion) 40002 41T Large Bevel Gear 40010 2.5x13.8mm Pin (Builds one differential for Center) 3x12mm Tapping 40004 Diff. Gear (Large) 40012 6x15mm Washer 40001 47T Spur Gear 40011 Diff. Gasket 40001 47T Spur Gear *Use 6x15mm washer to adjust the gear mesh. OPTION: #49016 SPUR GEAR 50T #49031 SPUR GEAR 50T, HD SPECIAL 40009 P6 O-Ring 36053 8x16mm Ball bearing 40005 Break Cap Joint 3x12mm Tapping

ASSEMBLY OF THE FRONT GEAR BOX 36053 8X16mm Ball bearing 40017 Gear Box OPTION: #49012 PINION GEAR 13TOOTH 36053 8X16mm Ball bearing 36053 8X16mm Ball bearing...4 40021 14TSmall Bevel Gear 40024 13x16x0.2mm Shim...2 40017 Gear Box 40024 13x16x0.2mm Shim 40021 14T Small Bevel Gear...1 Use shims to adjust gear mesh. ASSEMBLY OF THE FRONT ARMS HOLDER 94011 4x15mm Tapping (Small Head) Cement 90026 5x5mm Set 36730 Cap Joint 94014 4x45mm Tapping (Small Head) MISC. SCREW BAG 40067 4x15mm Tapping...2 90026 5x5mm Set...1 40022 Front Lower Arm Holder (Front) 40015 Front Lower arm Holder (Rear/Plastic) 4x16mm Tapping 36730 Cap Joint...1 40015 Front Upper arm Holder (Rear/Plastic) OPTION: #49002 CNC 7075 FRONT LOWER ARM HOLDER 4 x 16mm Tapping...4 4x45mm Tapping...2 94027 4x16mm Tapping

ASSEMBLY OF THE FRONT SHOCK TOWER 4mm Nylon Nut OPTION: 49003 CNC 7075 Alum. Shock Tower 40014 Front Shock Tower M4x15 TP 94004 M3x12 TP ASSEMBLY OF THE FRONT KNUCKLE ARMS Assembly of the left and gight hand side are the same. 36055 2.5x17mm Pin 40103 Front 40105 8mm CVA Joint (Long/Front) Knuckle Arm 40103 Front Knuckle Arm * "R" for right hand side. 36053 8x16x5mm Ball bearing L 36055 2.5x17mm Pin Cement 90026 5mm Set 36054 Alum. Wheel Hub 8mm 36053 8x16x5mm Bal lbearing Cement 90026 5mm Set 36053 8x16x5mm Bal lbearing 36054 Alum. Wheel Hub 8mm ASSEMBLY OF THE FRONT LOWER ARMS *Notice the direction of the steering ball. 36870 4X10mm Set * A 4 x 10mm set screw is used to adjust the ride height. 2mm 36053 8x16x5mm Bal lbearing 40105 8mm CVA Joint (Long/Front) Assembly of the left and gight hand side are the same. 40101 Upper Arm Ball End 4014 10mm Steering Ball 36870 4X10mm Set 40104 10mm Steering Ball *Notice the direction of the steering ball. 40101 Upper Arm Ball End 40104 10mm Steering Ball 40102 Front Lower Arm 40102 Front Lower Arm 40104 10mm Steering Ball

ASSEMBLY OF THE FRONT UPPER ARMS 40101 Front Upper Arm (Right) 36860 5x40mm Turnbuckle 40101 Front Upper Arm Ball End (Left) 10mm 0 10 20 30 40 50 mm ASSEMBLY OF THE FRONT LOWER ARMS 90020 2.5mm E-Ring 36170 Arm Shalf 3mmt Assembly of the right and left hand side are the same. 90021 3mm E-Ring 90020 2.5mm E-Ring 40023 Lower Arm Shaft (4mm) 90021 3mm E-Ring ASSEMBLY OF THE FRONT SUSPENSION ARMS Caster Adjuster * Insert the caster adjuster into upper arm. 40104 4x16mm Cap Assembly of the right and left hand side are the same. Cement * Insert the drive shaft into cap joint before assembly. Cement 40104 4x16mm Cap

ASSEMBLY OF THE FRONT STABILIZER 94007 3x20mm 40029 Stabilizer Ball End (Long) 30341 Stabilizer Ball 40029 Stabilizer Ball End 3x8mm Set 94007 3x20mm 30401 6mm Ball End 94033 3x3 Set 94033 3x3 Set 30341 A34B Stabilizer Ball...2 94007 3 x 20mm...2 94033 3 x 3mm Set...4 40018 Stabilizer Mount Plastic 94019 3x10mm Tapping 94019 3 x 10mm Tapping...2 94004 3 x 12mm Tapping...1 40019 Stabilizer 94019 3x10mm 94033 3x3 Tapping Set 94027 4 x 16mm Tapping...4 40013 Front Bumper * Insert the front bumper before assembly. 94004 3X12mm Tapping 40064 Chassis 4x16mm Tapping

ASSEMBLY OF THE WING STAY ( Take the plastic part from #40027Rear Win Stay Set. ) 49038 Rear Shock Tower, Orange 40027 Wing Mount 40027 Wing Mount 40027 Rear Body Mount 35313 3mm Nylon Nut *Insert the 3mm nylon nut before assembly. 3x12mm Tapping 40027 Wing Stay Post 94007 3x20 Tapping 3x20 Tapping 40027 Wing Mount 40027 Wing Stay ( Left ) 40027 Wing Stay ( Right ) 40027 Wing Mount OPTION: #49043 CNC ALIM. POSTS, WING MOUNT, ORANGE 3 x 12mm Tapping...3 3mm Nylon Nut...2 3 x 20mm Tapping...6 4 x 15mm Tapping ( Small Head )...2 4 x 15mm Tapping ( Small Head )...4 94004 3x12mm Tapping 94011 4x15mm Tapping ( Small Head ) OPTION: #49004 CNC 7075 REAR SHOCK TOWER 94011 4x15mm Tapping ( Small Head ) 94012 4x20mm ( Small Head )

ASSEMBLY OF THE REAR GEAR BOX ONTO CHASSIS 36055 2.5x17mm Pin 36054 8mm Wheel Hub 36053 8x16x5mm Bal l bearing 36081 Rear Upper Right 3 x10x3mm Plastic Washer 36082 Rear 36053 Wheel Shaft 8x16x5mm Ball bearing 3 x10x3mm Plastic Washer * A 4 x 10mm set screw is used to adjust the ride height. 4X10mm Set 40102 Rear Lower arm Assembly of the right and left hand side are the same. 90026 5mm Set 5 x 5mm Set...2 4 x 10 mm Set...2 90020 2.5mm E-Ring 90021 3mm E-Ring 36170 3mm Arm Shaft 90020 2.5mm E-Ring 40102 Rear Lower arm 2.5mm E-Ring...4 3 mm E-Ring...4 40023 Lower Arm Shaft 3mm 90021 E-Ring 3mm 90021 E-Ring 3mm 90021 E-Ring ASSEMBLY OF THE REAR UPPER ARMS (Make two upper arms for left an right hand side. ) 36860 5x40mm Turnbuckle 40065 Upper Arm Plastic Rod End 36850 7mm Ball 40065 Upper Arm Plastic Rod End 40065 Upper Arm Plastic Rod End 36860 5x40mm Turnbuckle 36850 7mm Ball 40065 Upper Arm Plastic Rod End 36850 7mm Ball 16mm

ASSEMBLY OF THE REAR AND ANTI-ROLL BAR 35313 3mm Nylon Nut Assembly of the right and left hand side are the same. 30341 Stabilizer Ball...2 Rear Upper Arm Assembly 94007 3 x 20mm...2 3 x 25mm Cap 94033 3 x 3mm Set...2 35313 3mm Nylon Nut 94035 3 x 8mm et...2. * Insert rear driver shaft before assembly. 94007 3 x 20mm Cap 94020 3 x 12mm Tapping...1 40107 Rear Driver Shaft (101mm) 40166 Stabilizer Ball End (Long) 30341 Stabilizer Ball 94007 3x20mm 40029 Stabilizer Ball End 3x8mm Set 30401 6mm Ball End 94007 3x20mm 94033 3x3 Set 94007 3 x 20mm Cap...2 94033 3x3 Set 35313 M3 Nylon Nut...2 90018 3 X 25mm Cap...2 94033 3 x 3mm Set...2 94019 3 x 10mm Tapping...2 40019 Stabilizer 40018 Stabilizer Mount Plastic 94019 3X10mm 94019 3X10mm 94033 3x3 Set

94027 4 x 16mm Tapping...4 40064 Chassis 94027 4 x 16mm Tapping ASSEMBLY OF THE SERVO SAVER 35313 M3 Nut...1 40035 Servo Saver Alum. Axle Tube 40037 Steering Plate Hex 40037 Steering Plate Hex 4x8mm Plastic flange Bushing Option: 40073 4x8mm Ball bearing flange 4x10mm...2 40037 Steering Plat Hex... 2 OPTION: #49014 CNC BALL BEARING AXLE TUBE 40031 Servo Saver Horn A 40095 Servo Saver Connecting Plate, Orange M3 Nut * Put the 3mm nut before assembly. 40031 Servo Saver Horn B 6x10mm Plastic Bushing Servo Saver Horn C 6x10mm Plastic Bushing Option: 40074 6x10mm Ball bearing 40074 6x10mm Ball bearing 40034 Servo Saver Spring Tension Adjuster 40033 Servo Saver Spring 40036 servo Saver Post 40036 Servo Saver Post * Take the 4x8mm Plastic Flange bushing and Plastic Bushing from servo saver plastic parts tree

ASSEMBLY OF THE SERVO SAVER ONTO THE CHASSIS 94009 4x10mm...2 4x10mm 40030 Front Plate 4x15mm Tapping 40027 Front Body Post * Assembly the front body post before assembly the Front Plate. 94004 3 x 12mm Tapping...1 3x12mm 94011 4 x 15mm Tapping ( Small Head )...2 94026 4 x 10mm...2 4x10mm OPTION: 49005 CNC 7075 Alum. Front Plate 49019 Graphite Front Plate ASSEMBLY OF THE FRONT STEERING ROD * Made two steering rods for left and right hand side. 36850 7mm Ball 36850 7mm Ball 35313 M3 Nylon Nut...2 40039 Alum. Tapper Washer...4 36850 7mm Ball 36700 Steering Ball End 40018 4x56mm Turnbuckle 35313 3mm Nylon Nut 36700 Steering Ball End 40018 4x56mm Turnbuckle 36700 Steering Ball End 94021 3 x 15mm...4 40039 3mm Tapper Washer(Alum.) 3x15mm 3x15mm 40039 3mm Tapper Washer(Alum.) * Anticlockwise mark. Assembly of the right and left hand side are the same. 0 10 20 30 40 50 mm 35.5mm

ASSEMBLY OF THE BRAKE AND SPLIT CENTER DIFF. MOUNT * Make brake pads for each side. * Take off the double sided paper before assembly. 36660 Brake Pad 36661 Brake Pad linings 40045 Brake Pad Adjustment 40044 Brake Pad Spring 40040 Center Diff. Mount 40044 Brake Pad Spring 40044 Brake Pad Spring 40040 Center Diff. Mount 40044 Brake Pad Spring Assembly the brake disc holder in the direction shown. OPTION: #49030 CNC 7075 SPLIT CENTER DIFF MOUNT. 40045 Brake Pad Adjustment Small Hole Large Hole 40040 Center Diff. Mount 40040 Center Diff. Mount Small hole to the Outside. 40040 Brake Disk Holder *Towards the front. 40040 Break Disc Holder *Towards the Rear. 40040 Brake Disc Holder 40045 Brake Pad...4 40044 Brake Pad Spring...8 40043 Center Diff. Mount Post...4 40043 Center Diff. Mount Post

ASSEMBLY OF THE CENTER DIFF. INTO CENTER DIFF. MOUNT Center Diff. Assembly 40042 Brake Disk 40042 Brake Disk 40042 Brake Disk 40042 Brake Disk OPTION: #49008 GRAPHITE BRAKE DISKS, 2PCS. 94003 3x10mm...4 94033 3 x 3mm Set...2 30171 Brake Lever...2 3x10mm Cement 40096 Center Diff. Plate, Orange Option 30212 5X8mm Ball Bearing 30211 Plastic Bushing 30213 Brake Cam 30171 Brake Lever 3x3mm Set 30171 3x3mm Brake Lever Set Cement 3x10mm 40031 Fuel Overflow Proof Plate Put the front brake lever as Shown. OPTION: #49018 GRAPHITE TOP CENTER PLATE

ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS 40028 Center Drive Shaft (93mm) 40028 Center Drive Shaft (93mm) 94026 4 x 12mm...2 4x12mm ASSEMBLY OF THE CENTER STIFFENER ONTO CHASSIS 40018 Center Chassis Brace ( Rear ) OPTION: 49015 CNC Alum. Chassis Brace Set 3x25mm Cap 3mm Nylon Nut 40018 Center Chassis Brace ( Front ) 3x12mm 94004 3 x 12mm Tapping...3 35313 3mm Nylon Nut...1 90019 3 X 25mm Cap...1 94027 4 x 16mm Tapping...4 2.6x10mm 4x16mm Tapping Tapping 4x16mm Tapping 4x16mm Tapping

ASSEMBLY OF THE STONE GUIDE Assembly of the right and left hand side are the same. OPTION: Stone Guard Yellow. 40078 Red. 40079 Lime. 40080 Blue. 40081 Black. 40046 40046 Stone Guard 3x10mm 3x10mm 40046 Stone Guard 3 x 10mm Tapping...6 3x10mm ASSEMBLY OF THE RECEIVER BOX * Use the screw provided with your radio 2x10mm Tapping 40047 Receiver Box Cover 40047 Receiver Box 40898 2x25mm 10280 Switch Cover Switch, Provided by Radio 3x10mm *Use the original battery case or rechargeable hump pack battery. Battery Case, Provided by Radio 2 x10mm Tapping...2 40047 Receiver Box 30560 Antenna Pipe 2 x 25mm...1 94003 3 x 10mm Tapping...1 * You must add padding for radio and battery once lid is closed. Do not let radio and/or battery be loose in box. Receiver Option: 10212 Hump Pack Battery

ASSEMBLY OF THE RADIO TRAY 3x10 Tapping 3x10mm Tapping 3x10mm Tapping 49039 Alum. Radio Tray, Orange Throttle Servo 3x10 Tapping Steering Servo OPTION: 49044 CNC ALUM. POST, RADIO TRAY, ORANGE 40027 Radio Tray Post ( Plastic ) 40027 Radio Tray Post ( Plastic ) 3x12mm Tapping 10274 Servo Post Servo Post * Take the servo post from servo saver plastic part tree. 94003 3 x 10mm Tapping...14 *Connect as per radio. 94019 3 x 10mm Tapping...8 OPTION: 49017 GRAPHITE RADIO TRAY. 3X10mm Tapping 40031 Transponder Holder 3x10mm Tapping * Use 4 pcs for receiver box. 3x10mm Tapping * Use 4 pcs for radio tray.

3 x 5mm 3 X 8mm Washer Notes: Non-Pull Start Engines... Alum. Washer behind the flywheel is not needed when using Force engines or similar types. O.S. Engines will require washer spacer. To check!..place the brass corn against the engine bearing, then flywheel. You should be covering one or two thread of the engine shaft. If this is the case, you do not need an additional washer behind the flywheel. ASSEMBLY OF THE CLUTCH INTO ENGINE 3 x 20mm Cap 3mm Nylon Locknut You must cut the engine shaft if too long. Count 6 threads in front of the flywheel and mark. This is all you need to tighten the clutch nut and mount the flywheel. Force Pull Start Engine w/threaded shalf... Force Pull Start Engines required NO spacer and no shaft cutting. The engines comes with an alum cast driver washer, you use this part as the spacer, not the alum. washer shown. Also, use the special flywheel brass corn. This corn fits the thread shaft diameter so you can tighten the flywheel against the drive hub. 30481 3 x 20mm Hex 30481 3 x 20mm Hex #10398-12T #10399-13T #10400-14T (stock) #10401-15T #10402-16T #10403-17T #10404-18T Clutch Bells #10102 Clutch Spring #10010 Clutch Shoes Black Type #10330 Brass, Corn (large hole) Note SG Shaft 30481 3 x 20mm Hex #34110 5x10x4mm Ball Bearing 3 x 5mm 3 x 8mm Washer Misc. Hardware #10099 * Fit the flywheel using a cross wrench or deep socket. If engine turns when tightening, hold piston with large thick tie-wraps and hard wood in exhaust port. Do not use metal, it will damage engine. #34110 5x10x4mm Ball Bearing #10098 SG Nut & Shim KiT #10091 Clutch Nut screw type * Shoes are trailing. * Place the clutch shoes with the clutch springs over the 3 pins of the flywheel. Using a screw driver as a lever, bend the small end of the clutch spring behind the clutch nut and press down to snap shoe in place. Option 10799 Flywheel Wrench #10329 Brass, Corn (sml hole) SEE NOTES ABOVE #10040 (stock) #10048 3 Pin OR 10049 Flywheel, Taper #10043 3 Pin Flywheel, Fan Options Threaded Shaft #30480 Engine Mount Clutch Spring 10100 - Springs, Polished, Med. 10101 - Spring, Gray, Hard 10102 - Spring, Black, Stock Clutch Shoes, 3 shoe clutch 10010 - Shoes, Carbon Material, Black 10011 - Shoes, Alum. CNC Blue, Lite Weight 10012 - Shoe, Alum. CNC Purple, Med. Weight ASSEMBLY OF THE AIR FILTER You must oil foam filter before use. Filter will not work if not oiled. Nylon Strap ( Small ) #10021 - Black #10027 - Yellow #10028 - Pink #10029 - Blue Air Filter Connector Nylon Strap ( Small ) Clean with soap and water only. You will damage foam if washed if fuel! #10016 Air Filter Sponge Refills #10017 - Blue #10018 - Yellow #10019 - Rose #10034 - Chrome Foam Air filters Unit 3 x 10mm Tapping #10013 - Mount Wire

INSTALLATION OF THE FUEL TANK AND ENGINE ONTO CHASSIS 3X15mm Tapping 40066 Pressure Nipple 3X15mm Tapping 40109 Fuel Tank, 140+cc 40066 Fuel Nipple * Assemble the fuel tank post before assembling the fuel nipple. Note Book Paper * Use note book paper to set gear backlash between spur gear and clutch bell. If the space is not correct the spur gear will be damaged. Spur Gear 3x20mm Cap 90 Degree Clutch Bell 38120 Fuel Tank Post * Loose or tighten 3x20mm cap screw and 5x10mm hex screw to align spur gear and clutch bell gear to 90 degree. * Take the fuel tank post from 40047 plastic parts tree. 10114 5mm Hex for Engine Mount 3x10mm Tapping 3x10mm Tapping ASSEMBLY OF THE MANIFOLD AND MUFFLER * Read this page very carefully. #10069 Manifold Adapter ( Red Silicone ) #31991 Manifold, Polished 3x3mm Set 40051 Muffler Wire #10120 Manifold Spring 40050 Muffler Mounting Post * Tighten the strip and cut off the excess. 4x10mm 5x5mm or 4x4mm Set #10184 #10079 Blue, Silicone Alum. CNC Tube Pressure Nipple * Drill a hole (Size 3.5mm) in the place and align as shown. Use a two part epoxy glue to #31992 full seal the nipple base to the nipple. Dual Chamber, Polished Option: 10182 Silicone Tube, Red 10183 Silicone Tube, Yel. 10184 Silicone Tube, Blue

ASSEMBLY OF THE FRONT STEERING ROD 35313 3mm Nylon Nut * Use the screw provided with your servo. 10768 Servo Horn * Enlarge this hole. 3x10mm 30410 6mm Tie Rod End 30690 3x30mm Tie Rod 30411 6mm Ball 3x15mm 30411 6mm Ball 30410 6mm Tie Rod End Parallel 16mm 0 10 20 30 40 50 mm * Align the steering servo as shown. ASSEMBLY OF THE BRAKE LINKAGE #30800 Brake System Plastic Parts Set Servo Mount * Cut the shaded area as shown. 2x6mm Washer 2x4mm 2mm Rod 2x8mm 3x3mm Set 3x25mm 10768 Servo Horn, Yel. 2mm Rod 36140 2mm Adjust Mount Adjust Mount 2x4mm 2mm Tie-Rod End 2x6mm Washer 2mm Nut * Cut the shaded area as shown. 2mm Rod 3x3mm set screw 3x10mm 3x3mm Set Plastic Collar 10300 Alum. Stopper Throttle Slider Throttle Spring 10300 Alum. Stopper 30530 Throttle Ball End

ASSEMBLY OF THE BRAKE LINKAGE INTO BRAKE ROD 10300 Alum. Stopper 3X3mm Set *Snap On. 5mm Fuel Tube 5mm Fuel Tube * Align throttle servo same as shown. Brake Idle Position Full Throttle *use the screw provided With your radio. USING BREAK ADJUST NUT Tighten Less Brake Loosen Loosen More Brake Tighten * Tighten or loose the adjuster nut will change the brake. ALIGN THROTTLE SERVO AND BRAKE SAME AS SHOWN ( Neutral Position ) Engine at idle ( Braking Position ) Brake is not on Brake is on Less Brake Brake Adjust Nut ( Full Throttle Position ) More Brake Engine at full throttle Loose Tighten * Tighten or loose the adjuster nut will change the brake. Brake is not on

SHOCK ASSEMBLY 32235 Shock Piston...4 40059 14.7mm O-Ring...4 32237 1mm Washer...4 49041 Spring Adjuster, Orange 40059 14.7mm O-Ring Fit the O-ring into groove. Make a PAIR for front 32237 7mm R-Ring 32237 3.5mm O-Ring 40076 Shock Cylinder 32237 2mm 32237 Washer 1mm Washer Oil Seal 40054 Short Shaft * Assembly 2 pieces of the shock shaft for front and rear. 40060 2.5mm Nylon Nut 32235 Shock Piston 2.6 x 5mm Washer * Short shaft for front. 32237 2mm Washer...4 J-47C Spring Adjuster...4 40056 Shock Plastic Rod End 49041 Spring Adjuster, Orange 40077 Shock Cylinder Make a PAIR for rear 40060 2.5mm Nylon Nut...4 40056 Shock Plastic Rod End APPLY OIL TO SHOCK BODY BEFORE INSTALLING COLLAR 40055 Short Shaft * Long shaft for rear. * Be careful not to damage shock shaft. FILLING THE SHOCKS WITH OIL 1. Pull down piston and pour oil into shock cylinder. Remove air bubbles by slowly moving piston up and down. 2. Pull down piston, attach pressure top and shock oil overflow with tissue paper. 3. Tighten up shock cap. 4. Assembly the dust cover. OIL 40093 Shock Cap Hard Coated *Leave 3mm. UP 40058 Shock Shaft Dust Cover down. *Move Slowly. 32033 Pressure Top * Fit into the groove. * Cut 6mm for front. ASSEMBLY OF THE SPRING OPTION: 40069 - Black, Stock, Spring Set 40070 - Green, Soft Set 40071 - Blue, Med. Set 40072 - White, Hard Set 30411 6mm Ball 40063 Spring Holder OPTION: 40063 - CNC Alum Spring Holder, Orange 40069 Black Shock Spring * Push 6mm ball joint into ball end. 40052 - Front Shock Set 40053 - Rear Shock Set

ASSEMBLY OF THE FRONT SHOCK ABSORBER 3x25mm Cap Assembly of the right and left hand side are the same. 36610 Shock Upper Fixing * Take the plastic bushing from the shock plastic parts tree. 30702 3 x 20mm Cap...2 35313 M3 Nylon Nut...2 Plastic Bushing 3mm Nylon Nut 90018 3 X 25mm Cap...2 36610 Shock Support...2 Assembly of the right and left hand side are the same. 3 x 20mm Cap 3x25mm Cap ASSEMBLY OF THE REAR SHOCK ABSORBER 36610 Shock Upper Fixing Plastic Bushing 3mm Nylon Nut 3 x 20mm Cap ASSEMBLY OF THE TIRES AND WHEELS 86035 wheel 86062 X Equal Pin Tire INSTANT GLUE 81095 Inner Sponge * Apply instant glue into the groove of the wheel.

ASSEMBLY OF THE WHEELS ONTO FRONT KNUCKLE ARM AND REAR HUB Assembly of the right and left hand side are the same. 30051 Wheel Nut 30051 Wheel Nut 86044 - Red 86045 - White 86046 - Lime 86047 - Yellow 86048 - Black 86049 - Chrome 17mm Dual Spoke, 2 pairs (4 wheels) per Bag. ASSEMBLY OF THE WING * Drill two 7mm holes for mounting. 25mm 40083 - Wing White 40084 - Wing Yellow 40085 - Wing Red 40086 - Wing Lime 40087 - Wing White 3x12mm 40027 Countersunk Plastic Washer OPTION: 49045 CNC Alum. Wing Washer Orange, 2 pcs. 25mm 40084 Wing, Yellow *Upper Deck Of The Wing. 0 25 20 15 10 5 5 10 15 20 25 * Check the hole spacing on the underside.

MOUNTING THE BODY 31149 Body Clips 31149 Body Clips FOR A STICK PACK BATTERY * Use tape to secure the battery. 40048 Stick Pack Battery Holder (5 Cell) Stick Pack Battery(5 Cell) ( Not Included.) Tape 3x12mm 3x12mm 40048 Battery Holder Mount 3x12mm 3x12mm * Insert battery wire into receiver and connect to the switch. 40048 Battery Holder Mount CHANGING WIDTH FROM 330mm TO ROAR LEGAL 310mm 310mm 330mm Adjustable width, lower arms. Simply cut outside 330mm pin holes. Leave as much plastic as possible

SET-UP GUIDE RIDE HEIGHT ADJUSTMENT 2mm Hex Use a 2mm hex screw to adjust the ride height. ing in the 4x10mm set screw...ride height becomes lower. Uncsrewing the 4x10mm set screw..ride height becomes higher. Soft 1 2 3 Firm Soft 1 2 Firm

ENGINE BREAK-IN AND TUNNING (BREAK-IN THE ENGINE BEFORE DRIVING THE CAR!) Choose a wide clear outdoor location with low dirt and dust. Set the car on box or holder with wheels off the ground. Turn on radio and car. Make sure throttle is at idle position. Fill fuel tank and set master engine needle. Prime fuel line and Heat glow plug before pull starting engine. When started, let engine fast idle for two tanks of fuel. OPTIONAL OFNA CAR STANDS WOOD BLOCK STARTING OF THE ENGINE How to start the engine: 1. Turn on transmitter and then receiver. 2. Fill fuel tank with fuel bottle. 3. Connect 1.2V glow plug starter. 4. Start engine with 12V starter or starter box ( Note the direction of the starter.) 5. After the engine be started, remove the 1.2V glow plug starter. * Follow the engine manufacturer instruction manuals regarding engine set-up, carburetor and maintenance. * To start the engine, use hand held starter motor or starter box. #10250 Starter Box 12V Starter Rubber wheel turns engine flywheel. 1.2V Glow Plug Starter * Note the direction of the starter. Connect with 12V battery

TUNING AFTER BREAK-IN Close master needle by turning clockwise until it stops. Then open needle by turning counterclockwise 3 turns (rich setting). When running car, adjust carb with 1/8 clockwise turns, slowly leaner, until the top speed good. Check engine temp, if possible, for no more 250 degrees. Adjust low end needle for best throttle response. Use only small turns. From idle, give it full throttle, if throttle is slow lean out needle until good. Adjust barrel stop so it will not close, accept for a small gap. This gap will be the idle setting. You will notice the idle will increase with a wide gap. Idle adjuster screw & Barrel Stop Lean Rich

APPENDIX PAGES

SHAFT START NOTICE: SOME VIOLATOR RTR KITS WILL COME WITH SHAFT START (same as Rotor Start). THEREFORE, A PULL START ENGINE IS NOT USED AND THE SHAFT START BACK PLATE IS ALREADY INSTALLED. BEFORE YOU CAN USE THE SHAFT START MOTOR HANDLE, YOU MUST FIRST GET OR BUY A STANDARD 7.2 BATTERY PACK. AFTER POWERING UP THE MOTOR HANDLE, INSERT THE SPECIAL DOG BONE SHAFT AND TURN OVER THE ENGINE. CHECK BEFORE STARTING: 1) IS THE FUEL LINE PRIMED? 2) IS THE CARBURETOR SET FOR BREAK-IN SETTINGS? 3) IS THE RADIO ON AND THROTTLE AND BRAKE LINKAGE CHECKED AND OKAY TO START? 4) MAKE SURE RADIO AND CAR RECEIVER BATTERY ARE ON AND WORKING WITH GOOD POWER. 5) PLACE THE GLOW HEATER ON PLUG. 6) HOLD THE CAR AND STARTUP THE ENGINE, BY PUMPING THROTTLE SLIGHTLY. DO NOT HIGH REV ENGINE WHEN IT STARTS, AT THIS TIME!