Linear Guides Series OSP-P NEW NEW Contents Description Data Sheet No. Page Overview.4.E 3-3 Plain bearing guide SLIDELINE.4.E 33-34 Roller guide POWERSLIDE.4.3E 35-38 Ball bushing guide GUIDELINE.4.4E 39-4 Aluminium roller guide PROLINE.4.5E 43-44 Recirculating ball bearing guide STARLINE.4.6E 45-5 Recirculating ball bearing guide KF.4.7E 5-56 3
OSP ORIGA SYSTEM PLUS Linear Guides SLIDELINE The cost-effective plain bearing guide for medium loads. Brake optional. Piston diameters 6 8 mm See data sheet.4.e (Standard)..E (ATEX-Version) Adaptive modular system The Origa system plus OSP provides a comprehensive range of linear guides for the pneumatic and electric linear drives. Advantages: Takes high loads and forces High precision Smooth operation Can be retrofitted Can be installed in any position Rodless Pneumatic Cylinder Series OSP - P Piston diameters 8 mm See data sheet..e (Standard)..E (ATEX-Version) POWERSLIDE The roller guide for heavy loads and hard application conditions Piston diameters 6 5 mm See data sheet.4.3e GUIDELINE The ball bushing guide for the heavy loads and greatest accuracy. Piston diameters 5 5 mm See data sheet.4.4e PROLINE The compact aluminium roller guide for high loads and velocities. Optional with brake. Piston diameters 6 5 mm See data sheet.4.5e STARLINE Recirculating ball bearing guide for highest loads and precision Piston diameters 6 5 mm See data sheet.4.6e KF GUIDE Recirculating ball bearing guide for high loads and precision. Correspond to FESTO dimensions (Type DGPL-KF) Piston diameters 6 5 mm See data sheet.4.7e 3 Data Sheet No..4.E-
Versions for pneumatic linear drive: Series OSP-P plastic wiper oiled felt wiper aluminium guide carriage Plain Bearing Guide SLIDELINE aluminium guide rail slide adjustment elements grease nipple pressure plate and adjustment screws OSP ORIGA SYSTEM PLUS Series SL 6 to 8 for Linear-drive Series OSP-P AP539EHAAX Option Integrated Brake Loads, Forces and Moments L L spring return brake piston with friction lining brake air connection Technical Data The table shows the maximum permissable values for smooth operation, which should not be exceeded even under dynamic conditions. The load and moment figures apply to speeds v <. m/s. * Please note: In the cushioning diagram, add the mass of the guide carriage to the mass to be cushioned. Features: ATEX-version (without brake) is also available (see data sheet no...e) Anodised aluminium guide rail with prism-shaped slideway arrangement Adjustable plastic slide elements optional with integral brake Composite sealing system with plastic and felt wiper elements to remove dirt and lubricate the slideways. Corrosion resistant version available on request. Any length of stroke up to 55 mm (longer strokes on request) Integrated Brake (optional) for series OSP-P5 to OSP-P5: Actuated by pressure Released by exhausting and spring return For further technical data see also linear drives OSP-P (..E) The right to introduce technical modifications is reserved Series For Max. moments Max. Maximum Mass of linear drive Mass * Order No. linear [Nm] loads braking force with guide of guide SLIDELINE ) drive [N] at 6 bar [kg] carriage for [N] ) [kg] with increase per OSP-P OSP-P M Ms Mv L, L mm stroke mm stroke without brake with brake SL6 OSP-P6 6 35.57..3 34 SL 5 OSP-P5 34 4 34 675 35.55.39.6 34 49 SL 3 OSP-P3 6 9 6 95 545.98.65.95 96 4 SL 4 OSP-P4 5 5 835 4.5.78. 343 4 SL5 OSP-P5 8 77 8 6.7.97.6 95 4 SL63 OSP-P63 6 6 5.66.47 3.3 853 SL8 OSP-P8 6 6 5 5.7.8 3.3 ) Only with integrated brake: Braking force on dry oil-free surface Values are decreased for lubricated slideways ) Corrosion resistant fixtures available on request For linear drives see..e, for ATEX-version see..e For mountings see.45.5e Data Sheet No..4.E- 33
Dimensions Series OSP-P Stroke + x A Stroke Air connection for brake For further mounting elements and options see accessories. FS For further information and technical data see data sheets for linear drives OSP-P (..E) Air connection for brake (Option) DB x EL Type SL5 to SL8 Type SL6 Dimension Table (mm) Series A B J M Z AA BB DB DD CF EC ED EE EG EJ EK EL EW FF FT FS GG JJ ZZ SL 6 65 4 69 3 M4 6 88 3 55 36 8 4 3 48 55 4 36 7 8 SL 5 7 4,5 M6 6 4 M5 6 7,5 47 53 39 6 6 3 64 73,5 5 SL 3 5 5,5 5 49 M6 5 85 M5 8 9 67 4 6 48 3 6 6 33 84 88 64 6 SL 4 5 8 5 55 M6 4 M5 77 4 64 5 58 6 6 34 94 98,5.5 78 SL 5 75 33 6 M6 84 64 M5 7 94 4 75 56 8 6 6 39 8,5 6 9 4 6 SL 63 5 38 56 79 M8 3 9 3 5 6 8 86 66 46 5 39 9 6 4 SL 8 6 47 348 96 M8 3 9 3 69 6 8 99 79 46 5 65 9 6 4 Mid-Section Support (for versions see.45.5e) Mid-section supports are required from a certain stroke length to prevent excessive deflection and vibration of the linear drive. The diagrams show the maximum permissable unsupported length in relation to loading. A distinction must be drawn between loading and loading. Deflection of.5 mm max. between supports is permissable. Note: For speeds v >.5 m/s the distance between supports should not exceed m. Load L Load L N 9 8 7 6 5 4 3,7 N 6 4 8 6 4 8 6 4,9 permissable unsupported length: SL 6, SL 5, SL 3,,3,5,7,9, SL 6 Loading SL 6 Loading SL 5 Loading SL 5 Loading SL 3 Loading SL 3 Loading,3,5,7 distance between supports k permissable unsupported length: SL4, SL5, SL63, SL8 SL4 Loading SL4 Loading SL5 Loading SL5 Loading SL63 Loading SL63 Loading SL8 Loading SL8 Loading m L L,9,,3,5,7,9,,3,5,7,9 3, 3,3 3,5 3,7 3,9 distance between supports k m loading loading 34 Data Sheet No..4.E-
Versions for pneumatic linear drive: Series OSP-P aluminium guide carriage Roller Guide POWERSLIDE aluminium clamping rail hardened steel rail roller cover with wiper and grease nipple OSP ORIGA SYSTEM PLUS Series PS 6 to 5 for Linear-drive Series OSP-P Loads, Forces and Moments L example: PS 5/35 L width of guide rail (35 mm) AP54EDZX Technical Data The Table shows the maximum permissable values for smooth operation, which should not be exceeded even under dynamic conditions. For further information and technical data see data sheets for linear drives OSP-P (..E) size of drive OSP-P5 * Please note: In the cushioning diagram, add the mass of the guide carriage to the mass to be cushioned. Features: Anodised aluminium guide carriage with vee rollers having rows of ball bearings Hardened steel guide rail Several guide sizes can be used on the same drive Corrosion resistance version available on request Max. speed v = 3 m/s, Tough roller cover with wiper and grease nipple Any length of stroke up to 35 mm, (longer strokes on request) The right to introduce technical modifications is reserved Series For linear Max. moments Max. load Mass of linear drive Mass * Order-No. drive [Nm] [N] with guide of guide Powerslide [kg] carriage for OSP-P ) with increase per [kg] M Ms Mv L, L mm stroke mm stroke PS 6/5 OSP-P6 45 4 45 4.93.4.7 85 PS 5/5 OSP-P5 63 4 63 4.5.4.7 5 PS 5/35 OSP-P5 7 7 4.7.4.8 6 PS 5/44 OSP-P5 75 65 75 3.6.5.5 7 PS 3/35 OSP-P3 7 7 4.6.6.8 86 PS 3/44 OSP-P3 75 65 75 3 3.4.7.5 87 PS 4/44 OSP-P4 75 65 75 3 4.6..5 33 PS 4/6 OSP-P4 5 9 5 3 6.3. 34 PS 5/6 OSP-P5 5 9 5 3 7.6.4.3 88 PS 5/76 OSP-P5 35 4 35 4.5.8 4.9 89 ) corrosion resistance version available on request (max. loads and moments are 5% lower) For linear drives see..e For mountings see.45.5e Data Sheet No..4.3E- 35
Dimensions Series OSP-P Stroke + x A Stroke Threaded holes Z x EF deep Dimension Table (mm) Series A B Z AA BB CC CF EE EF EG FF FS FT GG JJ PS6/5 65 4 4xM6 65 47 8 49 35 8 64 64 PS 5/5 6xM6 45 9 47 79.5 53 39 8 73.5 64 5 PS 5/35 6xM6 56 57 89.5 5.5.5 37.5 95.5 73 8 4 PS 5/44 6xM8 9 8 73 58 5 39 6 6 78.5 96 64 PS 3/35 5 5.5 6xM6 56 57 95.5 58.5.5 43.5 95.5 84.5 8 4 PS 3/44 5 5.5 6xM8 9 8 73 7 64 5 45 6 6 9 96 64 PS 4/44 5 8 6xM8 9 8 73.5 75 5 56 6 6 9.5 96 64 PS 4/6 5 8 6xM8 4 67 89.5 74 7 54 35 8.5 8.5 5 6 PS 5/6 75 33 6xM8 4 67 89 3.5 8 7 6 35 8.5 3.5 5 6 PS 5/76 75 33 6xM 8 78 9 55.5 93 64 85 39 35.5 6 5 36 Data Sheet No..4.3E-
Load L N 3 5 5 5,3 permissable unsupported length: PS 6/5, PS 5/5, PS 5/35, PS 5/44 PS 6/5 Loading PS 6/5 Loading PS 5/5 Loading PS 5/5 Loading PS 5/35 Loading PS 5/35 Loading PS 5/44 Loading PS 5/44 Loading,4,5,6,7,8,9,,,,3,4,5,6,7,8,9,,, distance between supports k m Mid-Section Support (for versions, see accessories) Mid section supports are required from a certain stroke length to prevent excessive deflection and vibration of the linear drive. The diagrams show the maximum permissable unsupported length in relation to loading. A distinction must be drawn between loading and loading. Deflection of.5 mm max. between supports is permissable. 3 N permissable unsupported length: PS 3/35, PS 3/44 Note For speeds v >.5 m/s the distance between supports should not exceed m. 5 PS 3/35 Loading PS 3/35 Loading Load L 5 PS 3/44 Loading PS 3/44 Loading 5,5,6,7,8,9,,,,3,4,5,6,7,8,9,,,,3,4,5 m loading loading distance between supports k 3 N permissable unsupported length: PS 4/44, PS 4/6 Load L 5 5 PS 4/44 Loading PS 4/44 Loading PS 4/6 Loading PS 4/6 Loading 5,5,6,7,8,9,,,,3,4,5,6,7,8,9,,,,3,4,5 m distance between supports k Load L N 4 35 3 5 5 5 permissable unsupported length: PS 5/6, PS 5/76 PS 5/6 Loading PS 5/6 Loading PS 5/76 Loading PS 5/76 Loading For further mounting elements and options see.45.e.,7,8,9,,,,3,4,5,6,7,8,9,,,,3,4,5,6,7,8 m distance between supports k Data Sheet No..4.3E-3 37
Service life. Calculation of load factor L F Calculation of service life is achieved in two stages: Determination of load factor L F from the loads to be carried Calculation of service life in km M M L F = + S M + V L + L + M V max L max M max M S max L max with combined loads, L F should not exceed the value. Lubrication For maximum system life, lubrication of the rollers must be maintained at all times. Only high quality Lithium based greases should be used. Lubrication intervals are dependant on environmental conditions (temperature, running speed, grease quality etc.) therefore the installation should be regularly inspected.. Service life calculation For PS 6/5, PS 5/5, PS 5/35, Service life [km] = and PS 3/35 For PS 5/44, PS 3/44, PS 4/44, Service life [km] = PS 4/6 and PS 5/6: For PS 5/76: Service life [km] = 6 (L F +,) 3 34 (L F +,5) 3 68 (L F +,5) 3 38 Data Sheet No..4.3E-4
Versions for pneumatic linear drive: Series OSP-P aluminium housing integral wiper steel guide shaft, hardened and ground ball bushing grease nipple Ball bushing guide GUIDELINE OSP ORIGA SYSTEM PLUS Loads, Forces and Moments L pressure force L tensile force Series GDL 5 to 5 for Linear-drive Series OSP-P L AP54EHAAX hight centre axis Technical Data The Table shows the maximum permissable values for smooth operation, which should not be exceeded even under dynamic conditions. For further information and technical data see data sheets for linear drives OSP-P (..E) * Please note: In the cushioning diagram, add the mass of the guide carriage to the mass to be cushioned. Features Anodised aluminium guide rail with four ball bushings Hardened and ground steel guide shafts Stainless steel guide shafts available on request Max. speed v = 3 m/s OSP-P: smooth slow speed operation v min. m/s. Any length of stroke up to 6 mm (longer strokes on request) The right to introduce technical modifications is reserved Series For linear Max. moments Max. load Mass of linear drive Mass * Order No. drive [Nm] [N] with guide [kg] of guide GUIDELINE with increase per carriage for L L L 3 mm mm M Ms Mv pressure force tensile force stroke stroke [kg] OSP-P ) GDL 5 OSP-P5 5 75 9 5 65.5.7. 75 GDL 3 OSP-P3 45 9 5 5 65 3.6.9. 8 GDL 4 OSP-P4 44 33 3 8 65 44 6.3.4. 77 GDL 5 OSP-P5 5 375 355 8 65 44 8.6.6. 83 ) corrosion resistance version available on request (max. loads and moments are 3% lower) For linear drives see..e Data Sheet No..4.4E- 39
Dimensions Series OSP-P Stroke + x A A Stroke B FU B FB FF AF FH FR FG FS FQ FO FP FP FP FP FM FL FN FC FK FD FJ øft FI FE For further options see.45.e. Note: The guideline linear guide must be mounted on a flat surface along its entire length. Arrangement of magnetic switches: Magnetic switches can be fitted anywhere on either side. The magnet can be screwed on to one of the four ball bushing housings from underneath. Magnetic switches see accessories.45.e,.45.4e Linear Drives OSP-P see data sheet..e Magnet 4 Data Sheet No..4.4E-
Dimension Table (mm) Series A B AF FB FC FD FE FF FG FH FI FJ øfk øfl FM FN FP FQ FR FS øft FU GDL 5 45 7 M6 78 86 73.5 6. 5.7 8 56.5 5.5 33.5 3 GDL 3 5 5.5 3 7 4 8 M6 86 98 85.5 6. 5.7 8 56.5 5.5 33.5 3 GDL 4 5 8 38 6 8 4 M8 4 8 4 7.5 6.8 73 6 38 6 36 GDL 5 75 33 48 8 6 M8 4 8 34 8 7.5 6.8 73 6 38 6 36 FO OSP-P x P5 P3 P4 P5 5. 75. 5. 75. 5.5 75.5 5.5 75.5 5. 76. 5. 76. 3 5.5 76.5 5.5 76.5 4 5. 77. 5. 77. 5 5.5 77.5 5.5 77.5 6 53. 78. 53. 78. 7 53.5 78.5 53.5 78.5 8 54. 79. 54. 79. 9 54.5 79.5 54.5 79.5 55. 8. 55. 8. 55.5 8.5 55.5 8.5 56. 8. 56. 8. 3 56.5 8.5 56.5 8.5 4 57. 8. 57. 8. 5 57.5 8.5 57.5 8.5 6 58. 83. 58. 83. 7 58.5 83.5 58.5 83.5 8 59. 84. 59. 84. 9 59.5 84.5 59.5 84.5 6. 85. 6. 85. 6.5 85.5 6.5 85.5 6. 36. 6. 86. 3 6.5 36.5 6.5 86.5 4 6. 37. 6. 87. 5 6.5 37.5 6.5 87.5 6 63. 38. 63. 88. 7 63.5 38.5 63.5 88.5 8 64. 39. 64. 89. 9 64.5 39.5 64.5 89.5 3 65. 4. 65. 9. 3 65.5 4.5 65.5 9.5 3 66. 4. 66. 9. 33 66.5 4.5 66.5 9.5 34 67. 4. 67. 9. 35 67.5 4.5 67.5 9.5 36 68. 43. 68. 93. 37 68.5 43.5 68.5 43.5 38 69. 44. 69. 44. 39 69.5 44.5 69.5 44.5 4 7. 45. 7. 45. 4 7.5 45.5 7.5 45.5 4 7. 46. 7. 46. 43 7.5 46.5 7.5 46.5 44 7. 47. 7. 47. 45 7.5 47.5 7.5 47.5 46 73. 48. 73. 48. 47 73.5 48.5 73.5 48.5 48 74. 49. 74. 49. 49 74.5 49.5 74.5 49.5 Data Sheet No..4.4E-3 FO OSP-P x P5 P3 P4 P5 5 75. 5. 75. 5. 5 75.5 5.5 75.5 5.5 5 76. 5. 76. 5. 53 76.5 5.5 76.5 5.5 54 77. 5. 77. 5. 55 77.5 5.5 77.5 5.5 56 78. 53. 78. 53. 57 78.5 53.5 78.5 53.5 58 79. 54. 79. 54. 59 79.5 54.5 79.5 54.5 6 8. 55. 8.5 55. 6 8.5 55.5 8.5 55.5 6 8. 56. 8. 56. 63 8.5 56.5 8.5 56.5 64 8. 57. 8. 57. 65 3.5 57.5 8.5 57.5 66 33. 58. 83. 58. 67 33.5 58.5 83.5 58.5 68 34. 59. 84. 59. 69 34.5 59.5 84.5 59.5 7 35. 6. 85. 6. 7 35.5 6.5 85.5 6.5 7 36. 6. 86. 6. 73 36.5 6.5 86.5 6.5 74 37. 6. 87. 6. 75 37.5 6.5 87.5 6.5 76 38. 63. 88. 63. 77 38.5 63.5 38.5 63.5 78 39. 64. 39. 64. 79 39.5 64.5 39.5 64.5 8 4. 65. 4. 65. 8 4.5 65.5 4.5 65.5 8 4. 66. 4. 66. 83 4.5 66.5 4.5 66.5 84 4. 67. 4. 67. 85 4.5 67.5 4.5 67.5 86 43. 68. 43. 68. 87 43.5 68.5 43.5 68.5 88 44. 69. 44. 69. 89 44.5 69.5 44.5 69.5 9 45. 7. 45. 7. 9 45.5 7.5 45.5 7.5 9 46. 7. 46. 7. 93 46.5 7.5 46.5 7.5 94 47. 7. 47. 7. 95 47.5 7.5 47.5 7.5 96 48. 73. 48. 73. 97 48.5 73.5 48.5 73.5 98 49. 74. 49. 74. 99 49.5 74.5 49.5 74.5 Note: The dimension FO is derived from the last two digits of the stroke: Example: Stroke 5 5 mm X For a cylinder OSP-P5 the adjacent table indicates that for x=5mm: FO = 6.5 mm 4
System Life The calculation for expected service life is achieved in three steps: Determination of the load factor L F, inserting actual values into the adjacent equation Determination of guidance constant K F Calculation of the service life in km. Calculation of load factor L F M M L F = + S M + V L + pressure L force + + L pressure force max M max M S max M V max with combined loads, L F should not exceed the value. L tensile force L tensile force max L max Lubrication For maximum system life, lubrication of the ball bushings must be maintained at all times. Only high quality Lithium based greases should be used. Lubrication intervals are dependant on environmental conditions (temperature, running speed, grease quality etc.) therefore the installation should be regularly inspected.. Guidance constant K F Installation guidance constant K F GDL 5, GDL 3 GDL 4, GDL 5 Horizontal Sideways 5 3 Vertical 9 3. Service life calculation Approximate service life is calculated using the following equation: Service life [km] = K F L F 3 4 Data Sheet No..4.4E-4
Versions for pneumatic linear drive: Series OSP-P wiper cover aluminium carriage Aluminium Roller Guide PROLINE lateral felt scraper aluminium guide rail aluminium roller shoe OSP ORIGA SYSTEM PLUS ground and calibrated tracks crosswise arranged rollers on needle bearings plastic wiper plastic cap plugs Series PL 6 to 5 for Linear-drive Series OSP-P AP539EHAAX The right to introduce technical modifications is reserved Option Integrated Brake Loads, Forces and Moments L L return spring cover plate for return spring brake lining brake air connection Technical Data The table shows the maximal permissible loads. If multiple moments and forces act upon the cylinder simultaneously, the following equation applies: The sum of the loads should not exceed >. With a load factor of less than, service life is 8 km The table shows the maximum permissible values for light, shock-free operation, which must not be exceeded even under dynamic conditions. Series For Max. Max. Maximum Mass of linear drive Mass * Order No. linear moments loads braking force with guide [kg] guide PROLINE drive [Nm] [N] at 6 bar with increase per carriage for OSP-P [N] ) mm mm [kg] without with M Ms Mv L, L stroke stroke brake brake PL 6 OSP-P6 8 54.55.9.4 855 - PL 5 OSP-P5 39 6 39 857 on request.65.4.75 856 86 PL 3 OSP-P3 73 9 73 7 on request 3.4.6.8 857 86 PL 4 OSP-P4 58 57 58 74 on request 4.35.7.7 858 86 PL 5 OSP-P5 49 49 3 on request 7.3.95.5 859 863 ) Only for version with brake: Braking surface dry oiled surface reduces the effective braking force. M M max brake piston M S M V L L + + + + M S max M V max L max L max Features: High precision High velocities ( m/s) Smooth operation - low noise Integated wiper system Long life lubrication Compact dimensions - compatible to Slideline plain bearing guide Any length of stroke up to 375 mm Integrated Brake (optional) for Series OSP-P5 to OSP-P5: Actuated by pressurisation Release by depressurisation and spring actuation * Please note: The mass of the carriage has to be added to the total moving mass when using the cushioning diagram. For linear drives see..e For mountings see.45.5e Data Sheet No..4.5E- 43
Dimension Table (mm) Series OSP-P PL6, PL5, PL3, PL4, PL5 ZZ A Z Stroke + x A Stroke EK EC B J B DB x EL JJ DD EJ GG FF FS JJ DD GG FF EG EE FT CF M Air connection for brake (Option) BB AA Type PL5 to PL5 Type PL6 Dimension Table (mm) Series OSP-P PL6,PL5, PL3, PL4, PL5 Series A B J M Z AA BB DB DD CF EC EE EG EJ EK EL FF FS FT GG JJ ZZ PL6 65 4 69 3 M4 98 88-3 55 3 4 3 - - - 48 7 55 36 7 8 PL5 7 4.5 M6 54 44 M5 6 7.5 3.5 53 39 6 6 64 3 73.5 5 PL3 5 5.5 5 49 M6 97 87 M5 8 9 4 6 48 3 6 6 84 5 88 64 6 PL4 5 8 5 55 M6 3 M5 47 64 5.5 58 6 6 94 3.5 98.5 78 PL5 75 33 6 M6 76 66 M5 7 63 75 57 8 6 6 9 8.5 9 4 6 Mid-Section Support (For versions, see.45.5e) Mid-section supports are required from a certain stroke length to prevent excessive deflection and vibration of the linear drive. The diagrams show the maximum permissible unsupported length in relation to loading. A distinction must be drawn between loading and loading. Deflection of.5 mm max. between supports is permissible. Loading L Loading L Note: For speeds v >.5 m/s the distance between supports should not exceed m. Permissible Unsupported Length PL6, PL5, PL3, PL4 und PL5 Load L [N] 4 35 3 5 5 PL5 Loading PL5 Loading PL4 Loading PL4 Loading PL3 Loading PL3 Loading PL5 Loading PL5 Loading PL6 Loading PL6 Loading 5,,4,7,,3,6,9,,5,8 3, Distance between supports k [m] 44 Data Sheet No..4.5E-
Versions for pneumatic linear drive: Series OSP-P integrated wiper grease nipple aluminium carriage Recirculating Ball Bearing Guide STARLINE polished, hardened steel guide rail guide carriage OSP ORIGA SYSTEM PLUS AP74EHAEX Loads, Forces and Moments Technical Data The table shows the maximum permissible loads. If multiple moments and forces act upon the cylinder simultaneously, the following equation applies: M M max M S M V L L + + + + M S max M V max L max L max The sum of the loads should not exceed > The table shows the maximum permissible values for light, shockfree operation, which must not be exceeded even under dynamic conditions. ** Please note: The mass of the carriage has to be added to the total moving mass when using the cushioning diagram. Series STL 6 to 5 for Linear Drive Series OSP-P Features: Polished and hardened steel guide rail For very high loads in all directions High precision Integrated wiper system Integrated grease nipples Any length of stroke up to 37 mm (longer strokes on request) Anodized aluminium guide carriage dimensions compatible with OSP guides SLIDELINE and PROLINE Installation height (STL6-3) compatible with OSP guides SLIDELINE and PROLINE Maximum speed STL6: v = 3 m/s STL5 to 5: v = 5 m/s The right to introduce technical modifications is reserved Series For Max. moments Max. loads Mass of linear drive Mass ** Order No. linear drive [Nm] [N] with guide guide STARLINE [kg] carriage for OSP-P with increase per [kg] M Ms Mv L L mm stroke mm stroke STL6 OSP-P6 3 5 3.598..68 STL5 OSP-P5 5 3 3.733.369.835 STL3 OSP-P3 6 6 6 3 3.934.56.8 3 STL4 OSP-P4 4 5 4 75 4 4.45.7.9 4 STL5 OSP-P5 58 58 75 4 7.36.936.88 5 For linear drives see..e For mountings see.45.5e Data Sheet No..4.6E- 45
Dimensions Series OSP-P STL6 to STL 5 stroke + x A A stroke A ZZ Z EC EG EE FT FS B J B CF M AA BB JJ DD JJ DD FF GG FF GG Type STL5 to PL5 Type STL6 Dimension Table (mm) Series OSP-P STL6 to STL5 Series A B J M Z AA BB CF DD EC EE EG FF FS FT GG JJ ZZ STL6 65 4 69 3 M4 93 9 55 3 5 4 4.6 48 8 55 36 7 8 STL5 7 4.5 M6 46.6 44 7.5 6 5 53 36. 64 3. 73.5 5 STL3 5 5.5 5 49 M6 86.6 84 9 8 5 6 4. 84 6. 88 64 6 STL4 5 8 5 55 M6 3 6 7 5.6 94 8.5 6.5 78 STL5 75 33 6 M6 7.9 66 7 3 85 6.3 3.5 8.5 9 4 6 46 Data Sheet No..4.6E-
Permissible Unsupported Length STL6 to STL5 Loading Top carrier L [N] 8 75 7 65 6 55 5 = OSP-P STL 6 = OSP-P STL 5 3 = OSP-P STL 3 4 = OSP-P STL 4 5 = OSP-P STL 5 Mid-Section Support (For versions, see.45.5e-8,.45.5e-9) Mid-section supports are required from a certain stroke length to prevent excessive deflection and vibration of the linear drive. The diagrams show the maximum permissible unsupported length in relation to loading. A distinction must be drawn between loading and loading. Deflection of.5 mm max. between supports is permissible. 45 Load 4 35 3 Loading Top carrier L Loading Side carrier L 5 5 5 3 4 5,,4,7,,3,6,9,,5,8 3, Distance between supports k [m] Permissible Unsupported Length STL6 to STL5 Loading Side carrier L [N] 8 75 7 65 6 55 5 45 = OSP-P STL 6 = OSP-P STL 5 3 = OSP-P STL 3 4 = OSP-P STL 4 5 = OSP-P STL 5 Note: For speeds v >.5 m/s the distance between supports should not exceed m. Load 4 35 3 5 5 5 3 4 5,,4,7,,3,6,9,,5,8 3, k [m] Distance between supports Data Sheet No..4.6E-3 47
Variable Stop The variable stop Type VS is used to provide intermediate stopping positions. It can be retrofitted and positioned anywhere along the stroke length. For every cylinder diameter two types of shock absorber are available see Shock Absorber Selection below. Mid-section supports and magnetic switches can still be fitted on the same side as the variable stop. Depending on the application, two variable stops can be fitted if required. Variable Stop Type VS6 to VS5 Arrangement with two variable stops Stop Shock absorber with plastic cap Shock absorber holder with shock absorber Shock Absorber Selection The shock absorber is selected in dependence on the mass and speed. The mass of the carrier itself must be taken into account. Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-STL6,,5 Speed [m/s], Type SA,5 Type SAS The values relate to an effective driving force of 78 N (6 bar),,,3,4,5,7 3 4 5 6 8 Mass [kg] Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-STL5 5 4 Speed [m/s] 3 Type SA Typ e SAS The values relate to an effective driving force of 5 N (6 bar) 48,,,3,5,7 3 4 5 6 7 3 4 5 7 Mass [kg] Data Sheet No..4.6E-4
Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-STL3 5 4,5 4 3,5 Speed [m/s] 3,5,5 Type SA4,5 Type SA4S,,,3,5,7 3 4 5 7 3 4 5 7 Mass [kg] The values relate to an effective driving force of 4 N (6 bar) Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-STL4 5 4,5 4 3,5 Speed [m/s] 3,5,5,5 Type SA Type SAS,,,3,5,7 3 4 5 7 5 7 Mass [kg] 5 The values relate to an effective driving force of 64 N (6 bar) Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-STL5 Speed [m/s] 5 4,5 4 3,5 3,5,5 Type SAI5,5 Type SAI5S,,,3,5,7 3 4 5 7 3 5 3 5 Mass [kg] The values relate to an effective Data Sheet No..4.6E-5 49
Dimensions Variable Stop Type VS6 to VS5 C SW E K P M G N H B A SW L D Dimension Table (mm) Variable Stop Type VS6 to VS5 Series Type A B C D E G H K L M N P SW SW OSP-STL6 VS6 3 4 5 33 3 8 38 6. 5.5.5 3 Mx 4.5 OSP-STL5 VS5 4 3 5 4.5 37 33 43 8 3.5 3 39 Mx 5 6 OSP-STL3 VS3 6 4 5 45.5 4 35 45 9 35.5 5 48 M4x.5 5 7 OSP-STL4 VS4 84 5 6 64 59 48 63 5.6 5 34 58.6 Mx.5 5 4 OSP-STL5 VS5 84-6 75 69 55 7 6.9 57 38 66.9 M5x.5 5 3 Order Information Variable Stop Type VS6 to VS5 Item Shock absorber holder complete with fittings without shock absorber Item Stop complete with fittings Item 3 Shock absorber with plastic cap Order Instructions Variable Stop Type VS6 to VS5 Item Description Size VS6 VS5 VS3 VS4 VS5 Type Order No. Type Order No. Type Order No. Type Order No. Type Order No. Stop, complete 96 97 98 99 Shock absorber 3 4 5 holder, complete 3 * Shock absorber, standard SA 79 SA 776 SA4 778 SA 77 SAI5 77 Shock absorber, version S SAS 797 SAS 777 SA4S 779 SAS 77 SAI5S 773 * Shock absorber with plastic cap 5 Data Sheet No..4.6E-6
Versions for Pneumatic Linear Drive: Series OSP-P KF Recirculating Ball Bearing Guide KF OSP ORIGA SYSTEM PLUS Loads, Forces and Moments Series KF6 to KF5 For Linear Drives Series OSP-P Features: AP7EHAEX Technical Data The table shows the maximum permissible loads. If multiple moments and forces act upon the cylinder simultaneously, the following equation applies: The table shows the maximum permissible values for light, shockfree operation, which must not be exceeded even under dynamic conditions. Anodized aluminium guide carriage, the mounting dimensions correspond to FESTO Type: DGPL-KF Polished and hardened steel guide rail For high loads in all directions High precision Integrated wiper system Integrated grease nipples Any length of stroke up to 37 mm (longer strokes on request) Maximum speed KF6, KF4: v = 3 m/s KF5, KF3, KF5: v = 5 m/s The right to introduce technical modifications is reserved M M max M S M V L L + + + + M S max M V max L max L max The sum of the loads should not exceed > * Please note: the mass of the carriage has to be added to the total moving mass when using the cushioning diagram. Series for Max. Moments Max. Load Mass of drive Mass * Groove Order No. Linear [Nm] [N] with guide [kg] guide stone Groove KF Drive with increase per carriage Stone for mm mm Thread OSP-P M Ms Mv L L stroke stroke [kg] Size KF6 OSP-P6 5 5.558..8 KF5 OSP-P5 9 35 9 3 3.5.369.67 M5 358 KF3 OSP-P3 33 44 33 3 3.673.56.896 M5 358 3 KF4 OSP-P4 346 9 346 7 4 4.67.7.53 M6 359 4 KF5 OSP-P5 48 7 48 75 4 7.38.936.76 M8 35 5 For linaer drives see..e For mountings see.45.5e Data Sheet No..4.7E- 5
Dimensions Series OSP-P KF6 to KF5 Stroke + x A, A Æ9 H7 M6 ÆFD 3 Stroke A A FA FB FC TH EC EG EE FT EW B M CF AA BB DD TB TA TE TF FS Size OSP-P KF5 Partial view A (with groove stone) groove stone J TH Size OSP-P KF3 to KF5 TG JJ TJ Size OSP-P KF6 6 x M4, deep DD x M5, deep DD Æ9 H7 M6 GG GG 5 x 5 H7, 3 deep Dimension Table (mm) Series OSP-P KF6, KF5, KF3, KF4, KF5 Series A B J AA BB CF DD EC EE EG EW JJ GG M KF6 65 4 76 93 85 48 5 5 4 4.6 5 3 KF5. 5 7.5 4 5 54.5 36. 3.5 46 KF3 5 5.5 6 46. 3 93.8 4 5 6.5 4. 3.5 59.8 KF4 5 8 5 88.5 67 3.3 4 69.5 5.6 6.5 6.8 KF5 75 33 8. 4 3 9.5 6.3 3.5 4 69 Series FA FB FC FD FT FS TA TB TE TF TG TH TJ KF6 7.7 9 6.5 56 9 KF5 6.5 39 4 4 G7 75 4.7 5..3 6.9 M5.5 4 KF3 34 53.8 34 5 G7 86.5 4.7 5..8 6.4 M5.5 4 KF4 4.5 56.8 4 5 G7 4 6 6.8.8 8.4 M6 7 5.5 KF5 5 65 5 5 G7 34 38 8. 4.5.5 M8 3 7.5 5 Data Sheet No..4.7E-
Permissible Unsupported Length OSP-P KF6 to KF5 Loading Top carrier Load 8 75 7 65 6 55 5 45 4 35 L [N] = OSP-P KF6 = OSP-P KF5 3 = OSP-P KF3 4 = OSP-P KF4 5 = OSP-P KF5 Mid-Section Support (For versions, see.45.5-5e,.45.5e-8,.45.5e-9) Mid-section supports are required from a certain stroke length to prevent excessive deflection and vibration of the linear drive. The diagrams show the maximum permissible unsupported length in relation to loading. A distinction must be drawn between loading and loading. Deflection of.5 mm max. between supports is permissible. 3 5 Loading Top carrier Loading Side carrier 5 5 3 4 5 L L,,4,7,,3,6,9,,5,8 3, Distance between supports k [m] Permissible Unsupported Length OSP-P KF6 to KF5 Loading Side carrier L [N] 8 75 7 65 6 55 5 45 4 = OSP-P KF6 = OSP-P KF5 3 = OSP-P KF3 4 = OSP-P KF4 5 = OSP-P KF5 Note: For speeds v >.5 m/s the distance between supports should not exceed m. Load 35 3 5 5 4 5 3 5,,4,7,,3,6,9,,5,8 3, k [m] Distance between supports Data Sheet No..4.7E-3 53
Variable Stop The variable stop Type VS is used to provide intermediate stopping positions. It can be retrofitted and positioned anywhere along the stroke length. For every cylinder diameter two types of shock absorber are available see Shock Absorber Selection below. Mid-section supports and magnetic switches can still be fitted on the same side as the variable stop. Depending on the application, two variable stops can be fitted if required. Variable Stop Type VS6 to VS5 Arrangement with two variable stops Stop Shock absorber with plastic cap Shock absorber holder with shock absorber Shock Absorber Selection The shock absorber is selected in dependence on the mass and speed. The mass of the carrier itself must be taken into account. Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-KF6,,5 Speed [m/s], Type SA,5 Type SAS The values relate to an effective driving force of 78 N (6 bar),,,3,4,5,7 3 4 5 6 8 Mass [kg] Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-KF5 5 4 Speed [m/s] 3 Type SA Type SAS The values relate to an effective driving force of 5 N (6 bar),,,3,5,7 3 4 5 6 7 3 4 5 7 Mass [kg] 54 Data Sheet No..4.7E-4
Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-KF3 5 4,5 4 3,5 Speed [m/s] 3,5,5 Type SA4,5 Type SA4S,,,3,5,7 3 4 5 7 3 4 5 7 Mass [kg] The values relate to an effective driving force of 4 N (6 bar) Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-KF4 Speed [m/s] 5 4,5 4 3,5 3,5,5,5 Type SA Type SAS,,,3,5,7 3 4 5 7 5 7 Mass [kg] 5 The values relate to an effective driving force of 64 N (6 bar) Shock Absorber Selection in Dependence on Mass and Speed for Series OSP-KF5 5 4,5 4 3,5 Speed [m/s] 3,5,5 Type SAI5,5 Type SAI5S,,,3,5,7 3 4 5 7 3 5 3 5 Mass [kg] The values relate to an effective driving force of N (6 bar) Data Sheet No..4.7E-5 55
Dimensions Variable Stop Type VS6 to VS5 C C SW E K M G N H P B A SW L D Dimension Table (mm) Variable Stop Type VS6 to VS5 Series Type A B C C D E G H K L M N P SW SW OSP-KF6 VS6 3 4 5 5 33 9.7 8 38 6. 5.5.5 4.5 M x 4.5 OSP-KF5 VS5 4 3 75 5 4.5 37 33 43 8 3.5 3 48 M x 5 6 OSP-KF3 VS3 6 4 5-45.5 4.5 35 45 9 35.5 5 37 M4 x.5 5 7 OSP-KF4 VS4 84 5 6-64 59 48 63 5.5 5 34 43 M x.5 5 4 OSP-KF5 VS5 84-6 - 75 69 55 7 6.9 57 38 58 M5 x.5 5 3 Order Information Variable Stop Type VS6 to VS5 Item Shock absorber holder complete with fittings without shock absorber Item Stop complete with fittings Item 3 Shock absorber with plastic cap Order Instructions Variable Stop Type VS6 to VS5 Item Description Size VS6 VS5 VS3 VS4 VS5 Type Order No. Type Order No. Type Order No. Type Order No. Type Order No. Stop, complete 86 87 88 89 9 Shock absorber 3 4 5 holder, complete 3 * Shock absorber, standard SA 79 SA 776 SA4 778 SA 77 SAI5 77 Shock absorber, version S SAS 797 SAS 777 SA4S 779 SAS 77 SAI5S 773 * Shock absorber with plastic cap 56 Data Sheet No..4.7E-6