ISO Cylinder Series C ø, ø0, ø, ø, ø, ø Conforming to ISO and CETOP RPP. Series Variations Standard Series C Series Non-rotating rod Series C ction Double acting Single acting Double acting Rod Single Double Single (SR, SE) Single Cushion Rod boot (ø, ) Rubber to ir Rubber ir Rubber Rubber Head cover style N E Y (Not for SE) Switch mount Rail and ore size 0 to to 0 to to to Page -- -- -- CJ CJ CM CG M M C CS C C C CP NC - Single acting Single (SR, SE) Rubber (Not for SE) to -- Direct mount Series CR ase Double acting Single Rubber to ront Double acting Single Rubber, -- Mounting style SR = Spring Return SE = Spring Extended --
Series C: ø, ø0, ø, Extended Service Life utomated assembly guarantees 00% repeatable mounting accuracy. ith abrasion resistant seals and replaceable nose seal, C cylinders offer exceptional service life. Corrosion Resistance ll parts are corrosion resistant. End covers and clevis are specially anodised while barrel is stainless steel. Piston rod is stainless steel up to ø. ø to ø0 is C hard chromed. ISO Standard is compliant with auto switch type. C: ø, ø0, ø, ø ronze ush earing High quality bronze bush in clevis bearing extends the life of cylinder. High Dust Resistance unique rod seal is employed to prevent entry of dust. The effectiveness of the seal makes the cylinder suitable for use in extremely dusty environments. C: ø, ø Leak Proof ssembly Double swaging of the end covers of the barrel provides an absolutely air tight union. --
ø, ø, ø, Replaceable Rod Seal Rod seal can be quickly replaced, greatly extending the cylinder life. (C ø, ). Minimized Side Clearance The close tolelance of the piston rod in the front end bush allows greater side loading. Series Variations Series C ction Double acting, Single rod Double acting, Double rod Single acting, Spring return Single acting, Spring extended High Speed ctuation Low friction and the standard elastomer cushion seals allow piston speeds up to 00 mm/s. Either rubber bumper or air cushions are available. Variations Rubber cushion ir cushion Non rotating Direct mount ottom side mounting Direct mount ront side mounting Rubber cushion ir cushion Rubber cushion Non rotating Rubber cushion Non rotating ore size 0 Easy-accurate Mounting Simple space-saving design with high dimensional accuracy makes these cylinders very easy to use. Large spanner flats on the rod and head covers greatly simplify their installation and positioning. C: ø, ø asic integrated clevis (N) Double end (E) Rod boot (Only ø, ø) ront nose ront nose in line port (Y) Mounting lexibility Different head covers allow a great variety of mounting options. uto switch Rail mounting and mounting Strong, Corrosion-proof arrel The risk of breakage or deformation due to external impacts is reduced by the use of harder, heavy walled stainless steel tube. Only bores ø, ø mm High temp. Low temp. Low speed ore ø to ø and all non-rotating C Heavy duty piston rod are already scraper R R piston rod and rod end nut piston rod, rod end nut and mounting nut -- CJ CJ CM CG M M C CS C C C CP NC -
Series C Stroke Selection The relation between the cylinder size and the maximum stroke depending on the mounting style ssuming that the force that is generated by the cylinder itself acts as a buckling force on the piston rod or on the piston rod and the cylinder tube, the table below indicates in centimeters the maximum stroke that can be used, which was obtained through calculation. Therefore, it is possible to find the maximum stroke that can be used with each cylinder size according to the relationship between the level of the operating pressure and the type of cylinder mounting, regardless of the load factor. Mounting style Mounting bracket diagram oot: L Rod side Head side flange: flange: G Clevis: C, D Head side trunnion: U oot: L oot: L Reference: Even under a light load, if the piston rod has been stopped by an external stopper at the extending side of the cylinder, the maximum force generated by the cylinder will act upon the cylinder itself. Rod side trunnion: U Center trunnion: O Series CS only Rod side Head side flange: flange: G Rod side Head side flange: flange: G Nominal symbol L G C D U T L G L Operating pressure (MPa) 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. (0) (0) (0) (0) (0) (0) (0) Maximum stroke that can be used according to buckling strength 0 (0) 0 (0) (0) (0) (0) (0) 0 (0) (0) (0) (0) (0) (0) (0) C 0 (0) (0) (0) 0 (0) (0) (0) (00) (00) (0) (0) 0 0 (cm) (00) (00) (0) (00) (00) (0) (00) (00) (0) (00) (00) The maximum stroke at which the cylinder can be operated under a lateral load The region that does not exceed the bold solid line represents the allowable lateral load in relation to the cylinder of a given stroke length. In the graph, the range of the broken line shows that the long stroke limit has been exceeded. In this region, as a rule, operate the cylinder by providing a guide along the direction of movement. fr Series C: ø, ø0, ø, ø Lateral load applied to the rod end fr (N) 0.0.0 0. 0.0 0 ushing (earing) 0 00 0 0 0 0 00 0 Series C: ø, ø Lateral load applied to the rod end fr (N) 00.0 0.0.0 Cylinder stroke C C C C C0 C CJ CJ CM CG M M C CS C C C CP NC - G 0. 0. 0. (0) (0) (0) (0) (0) (0) 0 0 (00) 0. 0 00 0 0 00 00 00 00 00 00 000 Cylinder stroke 00 --
ISO Cylinder: Standard/Non-rotating Type Double cting, Single/Double Rod Series C ø, ø0, ø, ø, ø, ø How to Order Double acting Single rod C D N 0 C J R Double acting Double rod C D E 0 C JJ Nil Nil D ult-in magnet Type Standard Non-rotating rod (Rubber cushion only) None uilt-in magnet Mounting style Symbol Mounting N asic integrated clevis E Double end ront nose Y ront nose in line port Double acting, Double rod: Only double end style (E). Except air cushion type. uto switch mounting type Rail mounting and mounting pplicable auto switches and bands are shown on page --. Please order auto switches and bands separately. Option piston rod, rod end nut R and mounting nut piston rod and R rod end nut ) Please refer to page -- for additional options. Only one option can be selected. ore size ore size 0 Stroke Standard stroke 0,, 0, 0, 0, 00 0,, 0, 0, 0, 00,, 0, 0 0,, 0, 0, 0, 00,, 0, 0, 0, 0 Not available with air cushion. Other strokes available on request. Max. stroke Standard Non-rotating Double rod 00 00 00 0 0 000 Cushion Nil C 000 00 Rubber cushion (Standard) ir cushion (Only N execution, bores 0 to mm) Rod boot (Only ø, ø) Nil J JJ ithout rod boot Nylon tarpaulin one side Heat resistant tarpaulin one side Nylon tarpaulin both sides Heat resistant tarpaulin both sides In the case of double acting/double rod. Mounting racket Part No. ccessory loating joint ore size Mounting bracket oot ( pc.) oot ( pcs. with Mounting mounting nut pc.) bracket lange Trunnion Clevis Single knuckle joint Double knuckle joint 0 CL0 CL0 C0 CT0 CC0 JD GM- J0--00 CL CL C CT CC JD GM-0 J--00 CL CL C CT CC JD J0D GM- GM0- J J -- -0- Replacement Parts or Standard Cylinders ore size Part no. C-PS C-PS Every set includes: n rod seal n seal retaining washer n retaining ring or Non-rotating Cylinders ( ) ore size Part no. Every set includes: C-PS n rod seal n seal retaining washer C-PS n retaining ring --
ISO Cylinder: Standard/Non-rotating Type Double cting, Single/Double Rod Series C ir cushion/single rod ir cushion/double rod JIS Symbol Double acting, Single rod Rubber cushion Double acting, Double rod Rubber cushion Rubber cushion/single rod Rubber cushion/double rod ir cushion ir cushion Non-rotating rod: Double acting, Single rod Non-rotating Specifications ore size Piston rod dia. Piston rod thread Port size M x 0. M x 0. 0 M x 0. M x 0. M x M x 0. M x M x 0. M x. G / 0 M0 x. G / ction luid Proof pressure Max. operating pressure Double acting, Single/Double rod ir. MPa.0 MPa Min. operating Spring return 0.0 MPa 0. MPa 0.0 MPa 0.0 MPa pressure Spring extended 0.0 MPa mbient and fluid temperature Cushion Lubrication Rod boot Piston speed llowable kinetic energy Nylon tarpaulin Heat resistant tarpaulin Rubber cushion ir cushion to 0 C (uilt-in magnet: 0 to 0 C) Rubber cushion, ir cushion (Except ø) (Non-rotating: Rubber bumper only) Not required. Use turbine oil Class ISO VG, if lubricated. 0 to 00 mm/s 0.0 J 0.0 J 0.0 J 0.0 J 0.J 0. J 0. J 0. J 0. J Non-rotating accuracy ± ' ± ' ± Stroke tolerance 0/+ Maximum ambient temperature of rod boots only. eight (Standard, Non-rotating rod) ore size Double action asic weight Double rod dd l weight for each 0 mm of stroke Mounting bracket ccessory Single knuckle joint Double knuckle joint loating joint CL CL C CT CC JlD GM- J-- Calculation: (Example) CN0-0, C0 asic weight (ø0)g dditional weight./0 mm of stroke Cylinder stroke 0 mm Mounting bracket g +. x 0/0 = g + = g 0 0 0. ±. 0 0 0 0 Max. ambient temperature 0 C Max. ambient temperature 0 C 0. 0. J 0. J ±0 ' ±0 ' 0/+. () ().. 0 0 0 00 0 0 (g) ( ): In the case of air cushion CJ CJ CM CG M M C CS C C C CP NC - --
Series C uto Switch Mounting, Minimum Possible Cylinder Stroke and Mounting Style ore size: ø, ø0, ø, ø uto switch model C C0 CC C0C HC H H HL HN No. of auto switches pcs. pcs. Different sides Same side Different sides Same side 0 0 0 0 0 0 pc. 0 0 0 Rail Mounting Style ore size: ø, ø0, ø, ø uto switch model No. of auto switches pcs. pcs. pc. /0 C/0C H 0 0H 0 0 0 J V JC J L 0 V VL 0 0 can not be mounted on bore size ø, ø0, ø cylinder. and Mounting Style ore size: ø, ø uto switch model C C0 CC C0C HC H H HL HN No. of auto switches pcs. n pcs. Different sides Same side Different sides Same side 0 0 + ( n ) 0 + (n ) (n =,...) + ( n ) + 0(n ) (n =,...) + ( n ) 0 + (n ) (n =,...) pc. 0 0 0 Rail Mounting Style ore size: ø, ø uto switch model /0 H/0H C/0C V J JC J L V VL No. of auto switches pcs. n pcs. 0 0 + ( n ) (n =,...) + ( n ) (n =,...) pc. 0 --
ISO Cylinder: Standard/Non-rotating Type Double cting, Single/Double Rod Series C Construction Double acting, Single rod C to Rubber cushion (Disassembly is not possible.)!!! y q r e i! o!0 C D CJ Component Parts No. q C D e r Description Rod cover Head cover N Head cover E Head cover Head cover Y Cylinder tube Piston rod Piston Piston Standard ø Material rass rass C/ Rubber cushion Qty.! o y!! u q r e! t!!!!!0 i N asic style integrated clevis u uilt-in magnet (Switch type piston) Non-rotating No. y u i o!0!!!! E Double end Rod cross section Description ush umper Piston gasket Tube gasket Rod seal Piston seal Rod end nut Mounting nut! y q ront nose Material Sintered bronze Urethane NR NR NR NR N asic style E Double end ront nose integrated clevis!! oy!! u q Non-rotating Qty. Y ront nose in line port (Switch type only) ( for switch type) C D Y ront nose in line port CJ CM CG M M C CS C C C CP NC - uilt-in magnet Component Parts No. Description Material Qty. q C D e r t y u i Rod cover Head cover N Head cover E Head cover Head cover Y Cylinder tube Piston rod Piston Plain washer ush ush Sintered bronze Sintered bronze Hard chrome plated Chromate Rod cross section No. Description o Retaining ring!0 Retaining ring!! ear ring! umper! umper! Piston gasket! Rod seal! Piston seal! Rod end nut! Mounting nut Material Resin Urethane Urethane NR NR NR Qty. (Switch type only) --
Series C Construction Double acting, Single rod C0 to ir cushion (Disassembly is not possible.) i! u!! y! q!! r e!! o w!0 Standard N integrated clevis uilt-in magnet Component Parts No. Description Material Qty. No. Description Material Qty. q Rod cover o Cushion ring rass w Head cover N!0 (Switch type only) e Cylinder tube! Mounting nut r Piston rod! Tube gasket NR Piston rass! Rod seal NR Piston rass (Switch type piston)! Piston seal NR y ush Sintered bronze! Check seal NR u i Cushion needle Steel ball earing steel! Piston gasket and cushion ring gasket NR ( for switch type)! Needle seal NR! Rod end nut C/ ir cushion @! @! @0 o y! @ u q r e!0 t!!!!! i w! Standard N integrated clevis uilt-in magnet Component Parts No. Description Material Qty. No. Description Material Qty. q Rod cover! Cushion needle lloy steel Electroless nickle plating w Head cover N! Cushion seal Urethane e Cylinder tube! Piston gasket NR r Piston rod Hard chrome plated! Rod seal NR t Piston Chromate! Piston seal NR y Plain washer! Cushion ring gasket NR u ush Sintered bronze! Cushion needle seal NR i ush Sintered bronze @0 Rod end nut o Retaining ring @ Mounting nut!0 Cushion ring rass @ Self locking ring! (Switch type only) @ Steel ball! ear ring Resin --0
ISO Cylinder: Standard/Non-rotating Type Double cting, Single/Double Rod Series C Construction Double acting, Double rod CE to Rubber cushion (Disassembly is not possible.)!!! y q e w o!!0 r! CJ Standard ø0 to ø r r u i t u CJ CM Standard ø uilt-in magnet ø uilt-in magnet ø0 to ø Component Parts No. Description Material Qty. No. Description Material Qty. q w e r t y u i Rod cover Cylinder tube Piston rod Piston Piston ush Spacer rass rass Sintered bronze rass for ø (Switch type piston) (Switch type only) o!0!!!!! umper Piston gasket Tube gasket Rod seal Piston seal Rod end nut Mounting nut Urethane NR NR NR NR CE/ Rubber bumper! u t!! y q e w i!!0 r o ( for switch type) CG M M C CS C C C CP NC Standard! - uilt-in magnet Component Parts No. Description Material Qty. No. Description Material Qty. q Rod cover o umper Urethane w Cylinder tube!0 Piston gasket NR e Piston rod Hard chrome plated! Rod seal NR r Piston Chromate! Piston seal NR t Plain washer! Rod end nut y ush Sintered bronze! Mounting nut u Retaining ring! (Switch type only) i umper Urethane --
Series C Construction Double acting, Double rod CE0 to ir cushion (Disassembly is not possible.) u! y!0! t! q!! w e!! i Standard o Component Parts uilt-in magnet No. Discription Material Qty. No. Discription Material Qty. q Rod cover o (Switch type only) w Cylinder tube!0 Rod end nut e Piston rod! Tube gasket NR Piston rass! Rod seal NR Piston rass (Switch type piston)! Piston seal NR t ush Sintered bronze! Check seal NR y u Cushion needle Steel ball earing steel! Piston gasket and cushion ring gasket NR ( for switch type) i Cushion ring rass! Needle seal NR! Mounting nut CE / ir cushion @0!0!!! u t!! y q e w i r!!!! Standard o uilt-in magnet Component Parts No. Discription Material Qty. No. Discription Material Qty. q Rod cover! Cushion seal Urethane w Cylinder tube! Piston gasket NR e Piston rod Hard chrome plated! Rod seal NR r Piston Chromated! Piston seal NR t Plain washer! Cushion ring gasket NR y ush Sintered bronze! Cushion needle seal NR u Retaining ring! Rod end nut i Cushion ring rass! Mounting nut o (Switch type only)! Self locking ring!0 Cushion needle lloy steel Electroless nickel plating @0 Steel ball --
ISO Cylinder: Standard/Non-rotating Type Double cting, Single/Double Rod Series C Dimensions Double acting, Single rod Rubber cushion: CN ore Stroke ithout magnet, uilt-in magnet XC + Stroke ir cushion: CN ore Stroke C ithout magnet, uilt-in magnet ith rod boot ore M E øc øcd H ød EE E G G H HR V N N ønd h RR S S U H XC Z ZZ M x. H. M x 0. 0. M x 0... 0 0 M x. H. M x 0. (.) (.) 0.. 0.. M x 0... (.) (.) 0 () () () () M x. M x. H. M x 0. H. M x 0. (.) (.). (.) (.)..... M x M x. 0. (.) (.).. 0. (.) (.). 0 () () 0 0 () () 0 () (0) () () M x. G /.().. M x. () () M x. 0. G /.() 0. 0 0. M0 x. () () 0 ( ): In the case of air cushion. ith Rod oot ore øe Item Stroke HR M øc øe f HR M Rail mounting type () Rail mounting type () øc 0 and mounting type () or non-magnet and mounting type () or non-magnet ød Cushion valve h h I f E d M x. M0 x. to 0 S V E M M CN Non-rotating, Piston rod (Rubber cushion only) Rod cross section to 00 øc H H ønd G 0 to 0 N EE Z + Stroke ZZ + Stroke h to 0 0 S + Stroke XC + Stroke G N S + Stroke Z + Stroke ZZ + Stroke EE G U N to 0 G N RR E øcd to 00 ønd 0 to 00 CJ CJ CM CG M M C CS C C C CP NC - ore Item Stroke to 0.. I to 00 0 to 0 to 0 to 0 to 00 0 to 00.. 0 0 00 00 to 0 h to 00 0 to 0 to 0 to 0 to 00 0 to 00 0 0 --
Series C Dimensions Double acting, Single rod Rubber cushion: CE ore Stroke ithout magnet, uilt-in magnet V H G G ød S E ønd EE EE E ith rod boot h øe øc ønd øc HR Rail mounting type () and mounting type () or non-magnet M H N S + Stroke ZZ + Stroke N CE Non-rotating, Piston rod (Rubber cushion only) M I f Rod cross section h ore M E 0 M x. M x. M x. M x. M x. M x. øc 0 ød..... EE M x 0. M x 0. M x 0. M x 0. G / G / G G H 0 HR 0 0...... 0. M x 0. M x 0. M x M x M x. M0 x. V N N..... 0.. 0... ønd h S 0 S 0 0 H ZZ 0 ith Rod oot Item ore Stroke M øc øe f 0 M x. M0 x. to 0 to 00 0 to 0 h to 0 0 to 0 to 00 0 to 00 ore Item Stroke to 0.. I to 00 0 to 0 to 0 to 0.. 0 0 to 00 0 to 00 00 00 to 0 h to 00 0 to 0 to 0 to 0 0 to 00 0 to 00 0 --
ISO Cylinder: Standard/Non-rotating Type Double cting, Single/Double Rod Series C Dimensions with Mounting racket Double acting, Single rod Rod foot, Rod and head foot: CL0, CL, CL LT -ø NH NH LT TR TR XS V CJ US Head cover E US Head cover N LS + Stroke XL + Stroke O Rod flange, Head flange: C0, C, C CJ CM T U T U CG M H H T Head cover E Head cover N Rod trunnion, Head trunnion: CT0, CT, CT L + Stroke T M C CS TM TZ TM TZ C C U TD e Head cover E U TD e Head cover N XV TT XZ + Stroke TT C CP Clevis: CC0, CC, CC E XC + Stroke øcd NC NH LT -ø U Head cover N O TR - LG ore 0 O US ø...... LT.. Rod foot, Rod and head foot NH LS () () () XL (0) (0) () 0 0 TR JS 0 0 XS.. 0 V.. 0 0 Rod flange, Head flange H...... T.. T 0 0 0 0 U 0 0.. L..(.) (0) () ore 0 TT U ( ): In the case of air cushion. Rod trunnion, Head trunnion øtd e TM TZ XV XZ () (0) () 0 øcd H E...... ø...... Clevis O U TR LG.......... NH LT.... XC () () () 0 --
Series C Dimensions Double acting, Single rod Rubber cushion: C/Y ore ithout magnet, uilt-in magnet Stroke V H G G ød ød S E ønd EE EE ith rod boot C/Y ore Stroke Non-rotating, Piston rod (Rubber cushion only) h øe øc øc HR Head cover Y HR Head cover Head cover Y Head cover M H N S + Stroke N Rail mounting type () and mounting type () or non-magnet Z + Stroke M I f Rod cross section h ore M E 0 M x. M x. M x. M x. M x. M x. øc ød.... 0. EE M x 0. M x 0. M x 0. M x 0. G / G / G G H 0 HR 0 0...... 0. M x 0. M x 0. M x M x M x. M0 x. V N.... N.. 0. 0... ønd h S 0 0 S 0 0 H Z 0 ith Rod oot Item ore Stroke M øc øe f 0 M x. M0 x. to 0 to 00 0 to 0 h to 0 0 to 0 to 00 0 to 00 ore Item Stroke to 0.. I to 00 0 to 0 to 0 to 0 to 00 0 to 00. 0 00. 0 00 to 0 h to 00 0 to 0 to 0 0 to 0 to 00 0 0 to 00 --
ISO Cylinder: Standard/Non-rotating Type Double cting, Single/Double Rod Series C Dimensions with Mounting racket Double acting, Single rod Rod foot: CL0, CL, CL LT NH NH -ø CJ TR US Head cover Y TR US Head cover O V XS CJ CM Rod flange: C0, C, C CG M M C T U T U CS C C H Head cover Y Head cover Rod trunnion: CT0, CT, CT H T C CP NC TM TZ TM TZ - TD e TD e TT U U XV Head cover Y Head cover ore 0 O US ø...... LT.. NH Rod foot TR JS 0 0 XS.. 0 V.. 0 0 Rod flange H...... T.. T 0 0 0 0 U 0 0.. TT U Rod trunnion TD e TM TZ XV --
Series C Dimensions Double acting, Double rod Rubber cushion: CE ore ithout magnet, uilt-in magnet Stroke Rail mounting type () and mounting type () or non-magnet Rail mounting type () ø to ø ith rod boot h øe øc V H G G H + Stroke ød S E ønd EE EE ønd E øc øc HR M H N S + Stroke ZZ + x Stroke N H + Stroke M Cushion Valve G G ir Cushion: CE ore Stroke C ithout magnet, uilt-in magnet HR and mounting type () or non-magnet N S + Stroke ZZ + x Stroke N ore M E øc ød EE 0 M x. M x. M x. M x. M x. M x. 0..... M x 0. M x 0. M x 0. M x 0. G / G / ith Rod oot Item ore Stroke M øc øe f 0 M G (.) (.) (.) 0.......()..() 0. ( ): In the case of air cushion. { }: In the case of built-in magnet M x. M0 x. H 0 I h HR 0 0. to 0 f V N ønd h S S H ZZ M x 0.. {} M x 0. M x M x.(.).(.)..(.). () () () M x. M0 x. () () 0 0 0{0} 0(0) () () 0 h to 00 0 to 0 to 0 0 to 0 to 00 0 to 00 ore Item Stroke to 0.. I 0 to 00 0 to 0 to 0 to 0 to 00 0 to 00 to 0. 0 00. 0 00 h to 00 0 ~ 0 ~ 0 ~ 0 ~ 00 0 ~ 00 0 0 --
ISO Cylinder: Standard/Non-rotating Type Double cting, Single/Double Rod Series C Dimensions with Mounting racket Double acting, Double rod Rod foot, Rod and head foot: CL0, CL, CL LT CJ NH -ø TRJS US XS LS + Stroke V LT CJ CM XL + Stroke O CG lange: C0, C, C M M C T U CS C C H T C CP Trunnion: CT0, CT, CT NC TM TZ - D e TT U XV ore O US ø LT 0........ Rod foot, Rod and head foot NH LS 0{} 0() 0() 0() XL {} (0) (0) (0) 0 0 ( ): In the case of air cushion. { }: In the case of auto switch. TR JS XS V 0 0.. 0.. lange H T 0 0........ T 0 0 0 0 U 0 0.. TT U TD e Trunnion TM TZ XV --
Series C ccessory Dimensions Single nuckle Joint/DIN-DIN Double nuckle Joint/ISO0-DIN d d b b øf d α α l l g b e øj d d C l h ore Model Thread d dh h 0 JD JD JD JD JD J0D M x 0. M x 0. M x M x M x. M0 x. 0 d b b.0.0.. 0. l 0 0 d α 0 l. 0. 0. 0. 0 ore 0 Model GM- GM- GM- GM- GM- GM0- Thread e M x 0. M x 0. M x M x M x. M0 x. b 0 d 0 f g c j a 0 0 0 0 loating joint: Series J In the case of dimension without C M M U ød U G H C E P E M ore Model Nominal Pitch thread dia., 0, J0--00 J--00 J-- J-0-0 0... C..... 0 D E.. G H 0 Maximum screwed depth P. llowable eccentricity U 0. 0. 0. 0. Max. operating tension and compression power (kn) 0.0 0... --
ISO Cylinder: Standard/Non-rotating Type Double cting, Single/Double Rod Series C uto Switch Mounting Position and Mounting Height Double acting, Single rod (and mounting type) (Rail mounting type) C C0. 0. CJ CC C0C H H HL HN HC.... H 0H C 0C. 0... ø0. CJ CM CG M M C CS C uto Switch Mounting Position ore 0 C C0 CC C0C 0 (.) (.).. ().. () (.) (.) (.) (.) (.) (.). (.). (.) () () () () () 0 () 0. (.) () () (). (.) () () (). () (). (.). (.) () () () () () (). (.). (.) () (). (.). (.). (.). (.). (.). (.) ( ) for air cushion type. The lower of ø is a number for CD/Y. im at this number.. H/0H C/0C /J /J V V JC/ L H HC H HL HN J J L JC. V V VL. ø0 C C CP NC - C uto Switch Mounting Height ore 0 C/C0 H H HL HN Hs... im at this number. CC C0C 0 H/0H /J /J L C 0C HC JC V V VL Hs Hs Hs Hs Hs Hs Hs Hs.................... --
Series C uto Switch Mounting Position and Mounting Height Double acting, Double rod (and mounting type) (Rail mounting type) C C0 0.. CC C0C. H 0H 0.. H H HL HN.. C 0C.. ø0. HC.. J J L uto Switch Mounting Position ore 0 C C0 CC C0C 0 (.) (.) () () (.) (.) () (). (.). (.) ( ) for air cushion type. 0.. (). (.). (.). (.). (.). (.) () 0.. (). (.) () H/0H C/0C /J /J V V JC L / (.) (.) () () () () () () H HC H HL HN (.) () () () (.) () () () () () () (). (.). (.). (.). (.). (.). (.) JC. V V VL. ø0 C uto Switch Mounting Height ore 0 C/C0 H H HL HN... im at this number. -- Hs CC C0C 0 H/0H /J /J L C 0C HC JC V V VL Hs Hs Hs Hs Hs Hs Hs Hs....................
ISO Cylinder: Standard/Non-rotating Type Single cting, Spring Return/Extended Series C ø, ø0, ø, ø, ø, ø Single acting, Spring return/ Spring extended Nil D uilt-in magnet Type Nil Standard Non-rotating rod (Rubber cushion only) None uilt-in magnet How to Order C D N 0 S Symbol N E Y ore size Stroke ore size Standard stroke 0 0,, 0, 0 0,, 0, 0, 0, 00,, 0 Other strokes available on request. Mounting style Mounting asic integrated clevis Double end ront nose ront nose in line port Except single acting spring extended type. Max. stroke 0 0 ction S T uto switch mounting style Rail mounting and mounting pplicable auto switches and bands are shown on page --. Please order auto switches and bands separately. Option R R piston rod, rod end nut and mounting nut piston rod and rod end nut Single acting, Spring return Single acting, Spring extended CJ CJ CM CG M M C CS C C C CP NC - Mounting racket Part No. ore size Mounting bracket oot ( pc.) Mounting bracket oot ( pcs. with mounting nut pc.) lange Trunnion Clevis Single knuckle joint Double knuckle joint ccessory loating joint 0 CL0 CL0 C0 CT0 CC0 JD GM- J0--00 CL CL C CT CC JD GM-0 J--00 CL CL C CT CC JD J0D GM- GM0- J J -- -0- Replacement Parts or Standard Cylinders ore size Part no. C-PS C-PS Every set includes: n rod packing n packing retaining washer n retaining ring or Non-rotating Cylinders ( ) ore size Part no. Every set includes: C-PS n rod packing n packing retaining washer C-PS n retaining ring --
Series C Specifications ore size 0 Piston rod dia. 0 Piston rod thread M x 0. M x 0. M x M x M x. M0 x. Spring return Port size ction luid Proof pressure Max. operating pressure M x 0. M x 0. M x 0. M x 0. G / Single acting, Single rod, Spring return/extend ir. MPa.0 MPa G / Min. operating pressure Spring return Spring extended 0. MPa 0. MPa 0. MPa 0. MPa 0. MPa Spring extended mbient and fluid temperature to 0 C (uilt-in magnet type: 0 to 0 C) Rubber cushion Cushion Lubrication Piston speed Rubber cushion (Standard) Not required. Use turbine oil Class ISO VG, if lubricated. 0 to 00 mm/s llowable kinetic energy 0.0 J 0.0 J 0.0 J 0.0 J 0. J 0. J Non-rotating Non-rotating accuracy Stroke tolerance ± ' ± ' ± 0/+ ± ±0 ' ±0 ' 0/+. JIS Symbol Standard Spring Retracting orce (Standard, Non-rotating) Spring Return ore size Standard stroke Spring force 0 0 00 0 Retract Extended Retract Extended Retract Extended Retract Extended Retract Extended (N) Spring return Spring extended 0 0,, 0...0.....0.... Non-rotating 0,, 0, 00, 0............. 0....................... Spring return Spring extended Spring Extended ore size Standard stroke Spring force 0 0 00 0 Retract Extend Retract Extend Retract Extend Retract Extend Retract Extend (N)...... 0 0,, 0....0......0.. 0,, 0, 00, 0.....0 0......................... --
ISO Cylinder: Standard/Non-rotating Type Single cting, Spring Return/Extended Series C uto Switch Mounting, Minimum Possible Cylinder Stroke and Mounting Style ore size: ø, ø0, ø, ø C C0 uto switch model CC C0C HC H H HL HN No. of auto switches pcs. pcs. Different sides Same side Different sides Same side 0 and Mounting Style ore size: ø, ø uto switch model C C0 CC C0C HC H H HL HN 0 0 0 No. of auto switches pcs. n pcs. Different sides Same side Different sides Same side 0 0 0 0 + ( n ) 0 + (n ) (n =,...) + 0( n ) + 0(n ) (n =,...) + ( n ) 0 + (n ) (n =,...) pc. 0 0 0 pc. 0 0 0 Rail Mounting Style ore size: ø, ø0, ø, ø uto switch model /0 C/0C H 0H J V JC J L V VL No. of auto switches pcs. pcs. 0 0 Rail Mounting Style ore size: ø, ø uto switch model /0 H/0H C/0C V J JC J L V VL 0 0 No. of auto switches pcs. n pcs. pc. cannot be mounted on bore size ø, ø0, ø cylinder. 0 0 + ( n ) (n =,...) + ( n ) (n =,...) 0 0 0 pc. 0 CJ CJ CM CG M M C CS C C C CP NC - --
Series C Construction Single acting, Single rod Spring return: C to -S (Disassembly is not possible.)! i r! q e!!!!0!! t! C D Standard ø0 to ø N asic execution integrated clevis E Double end ront nose Y ront nose in line oprt t! o y o u i r q Non-rotating Standard ø uilt-in magnet ø uilt-in magnet ø0 to ø Rod cross section Component Parts No. Description Material Qty. No. Description Material q C D e r t y u i Rod cover Head cover N Head cover E Head cover Head cover Y Cylinder tube Piston rod Piston Piston Piston ush rass rass rass Sintered bronze (Switch type only) (Switch type only) o!0!!!!!!!!! umper Return spring Return spring Spring guide Spacer Piston gasket Tube gasket Piston seal Rod end nut Mounting nut Urethane Piano wire Piano wire rass rass NR NR NR Qty. (Switch type only) ( for switch type) Spring Extended: C to -T (Disassembly is not possible.) @0! i @ r q!0 e!! t! e!!!! C Standard ø0 to ø N asic execution E Double end ront nose integrated clevis in line port t o! u o y! i r q Non-rotating Standard ø uilt-in magnet ø uilt-in magnet ø0 to ø Rod cross section Component Parts No. Description Material Qty. No. Description Material q C e r t y u i o Rod cover Head cover N Head cover E Head cover Cylinder tube Piston rod Piston Piston Piston ush rass rass rass Sintered bronze (Switch type only) (Switch type only) (Switch type only)!0!!!!!!!!! @0 umper Return spring C Spring guide Spring seat Plug Spacer Piston gasket Tube gasket Rod seal Piston seal Rod end nut Urethane Piano wire rass rass Steel rass NR NR NR NR @ Mounting nut -- Qty. ( for switch type)
ISO Cylinder: Standard/Non-rotating Type Single cting, Spring Return/Extended Series C Construction Single acting, Single rod Spring return: C/ S @0 u @ qr 0 0 e!! t!!!!!0 i C D Strokes 0mm Standard N asic execution E Double end ront nose Y ront nose integrated clevis in line port r @0 oy! @ u! q!! 0 e! t!!!!!0 i @ r@0 oy! @ u! q Strokes > 0mm Component Parts No. q C D e r t y u i o!0 0 Description Rod cover Head cover N Head cover E Head cover Head cover Y Cylinder tube Piston rod Piston Plain washer ush ush Retaining ring Retaining ring Return spring Material Sintered bronze Sintered bronze Piano wire Qty. Spring extended: C/-T Standard Hard chrome plated Chromate Zinc chromated No. 0!!!!!!!!! @0 @ @ uilt-in magnet Description Return spring Spring guide Spring holder Set screw ear ring umper umper Piston gasket Rod seal Piston seal Rod end nut Mounting nut Material Piano wire Resin Urethane Urethane NR NR NR @0 ro y! @ u q! t!!!! e!0!!! i C Standard N asic execution E Double end integrated clevis @ @0 roy! @ uq Non-rotating Rod cross section Non-rotating rod Qty. ront nose in line port Zinc chromated (Switch type only) CJ CJ CM CG M M C CS C C C CP NC - Component Parts uilt-in magnet Rod cross section No. q C e r t y u i o!0 Description Rod cover Head cover N Head cover E Head cover Cylinder tube Piston rod Piston Plain washer ush ush Retaining ring Return spring Material Sintered bronze Sintered bronze Piano wire Qty. Hard chrome plated Chromate Zinc chromated No.!!!!!!!!! @0 @ @ Description Spring guide Spring guide Set screw ear ring umper umper Piston gasket Rod seal Piston seal Rod end nut Mounting nut Material Resin Urethane Urethane NR NR NR Qty. (Switch type only) --
Series C Dimensions Single acting, Spring return C N E ore Stroke S ithout magnet, uilt-in magnet XC + Stroke ød ød S E H EE G E øcd ønd ønd HR HR Head cover E Head cover N Rail mounting type () Head cover E E d Head cover N and mounting type () or non-magnet M øc H V N S + Stroke Z + Stroke ZZ + Stroke N U RR CN, CE Non-rotating (Piston rod) Rod cross section ore M E øc øcd H ød EE E 0 M x. M x. M x. M x.. M x 0.. M x 0.. M x 0.. M x 0. M x. G / M x. 0. G / ore S XC to 0 to 00 0 to 0 to 0 to 00 0 to 0 0 (){()} (0){(0)} 0(.){0(.)} (.){(.)} {} {.}.() {(.)}. (0.) {(.)}. (0){(0)} (){()} (.){(.)} (.) {(.)} {} 0{.}.(0) {(.)}. (.) {(.)} 0. ( ): In the case of auto switch style. { }: In the case of non-rotating rod. G H 0 HR 0 0. V N N ønd h RR.. M x 0. M x 0..... 0 0.. M x M x. 0... 0... 0. M x. M0 x. to 0 (){()} (0){(0)} (.) {0(0.)} (0.) {0(.)} {0} {.} Z to 00.() {(.)}. 0 to 0 to 0 (){(0)} (0){(00)} to 00 (.) {0(.)} 0. 0(0.) {(.)} (.) {(.)} {} {0.} ZZ.() {(0.)}. S 0 0 U H 0 to 0 (.) {(.)}. --
ISO Cylinder: Standard/Non-rotating Type Single cting, Spring Return/Extended Series C Dimensions with Mounting racket Single acting, Spring return Rod foot, Rod and head foot: CL0, CL, CL LT NH NH -ø Rod flange, Head flange: C0, C, C Rod trunnion, Head trunnion: CT0, CT, CT Clevis: CC0, CC, CC ore 0 Head cover E T U H U TD e TM TZ Head cover E TR US Head cover E NH Head cover N U E U T U H TD e TM TZ Head cover N LT Head cover N XV Rod foot, Rod and head foot TR US Head cover N T TT XC + Stroke Rod flange, Head flange LS XL L O US ø LT NH TR JS XS V H T T U to 0 to 00 0 to 0 to 0 to 00 0 to 0 to 0 to 00 0 to 0 () ().(.).. {()} {()}.... 0. {.(.)} () ().(.).. {()} {()}.... 0. {.(.)} (.) (.) (.). {(.)} {(.)}. 0 {(.)} (.).(0) (.) (.) 0.() (.) (.). {(.)} {(.)} {(.)} {0(0.)} {(.)} {(.)}. 0 {(.)}. {} 0{} 0 0. 0 {}. {.}.. 0{.}.. 0 0 0. 0 {.}.. O TR LG CD XS -ø LS + Stroke XL + Stroke L + Stroke XZ + Stroke V T LT O TT.(0) (.) {(.)} {(.)} CJ CJ CM CG M M C CS C C C CP NC - Rod trunnion, Head trunion ore XZ XC TT U TD e TM TZ XV øcd H E ø O U TR LG NH LT to 0 to 00 0 to 0 to 0 to 00 0 to 0 () (0) {()}...... {(0)} () () 0 {()}...... {()} (.) (.) {(.)}.... {(.)} (.).(0) (.) (.).(0) {(.)} {(.)} {(.)}.... {(.)} {(.)} 0{} 0... {} 0 {.}. 0.... 0{.}.. ( ): In the case of auto switch style. { }: In the case of non-rotating rod. Clevis (.) {(.)} --
Series C Dimensions Single acting, Spring return C Y ore Stroke S ithout magnet, uilt-in magnet H ød ød S E EE G C, CY Non-rotating (Piston rod) ønd HR HR Head cover Y Head cover Head cover Y Head cover Rail mounting type () and mounting type () or non-magnet M øc H V N Z + Stroke S + Stroke N Rod cross section ore M 0 E M x. M x. M x. M x. M x. M x. øc 0 ød..... EE M x 0. M x 0. M x 0. M x 0. G / G / G H 0 HR 0 0...... 0. M x 0. M x 0. M x M x M x. M0 x. V N N ønd h..... 0... 0.. S 0 0 H ore to 0 (){()} 0 (0){(0)} 0(.){0(.)} 0(.){0(.)} {} {.} S Z to 00 0 to 0 to 0 to 00 0 to 0 (0){(0)} (){()} (.){(0.)}.(){(.)} (.){(.)} (.){(0.)} 0.(0){(.)} (.){0(.)} 0{}.. {.}.. ( ): In the case of auto switch type. { }: In the case of non-rotating. --
ISO Cylinder: Standard/Non-rotating Type Single cting, Spring Return/Extended Series C Dimensions with Mounting racket Single acting, Spring return Rod foot: CL0, CL, CL LT NH NH -ø CJ TR US TR US O V XS CJ Head cover Y Head cover CM Rod flange: C0, C, C CG M M C T U T U CS C C T C Head cover Y Head cover CP Rod trunnion: CT0, CT, CT NC TM TZ TM TZ - TD e TD e TT U Head cover Y U Head cover XV ore 0 O US ø...... LT.. NH Rod foot Rod flange Rod trunnion TR JS XS V H T T U TT U TD e TM 0 0.. 0.. 0 0........ 0 0 0 0 0 0.. TZ XV --
Series C Dimensions Single acting, Spring return C N E ore Stroke T ithout magnet, uilt-in magnet XC + x Stroke ød ød S H + Stroke V V G EE EE E øcd ønd ønd HR HR E d M øc N N U Head cover E Head cover N Rail mounting type () Head cover E Head cover N and mounting type () or non-magnet H + Stroke Z + x Stroke ZZ + x Stroke S + Stroke RR CN/E Non-rotating (Piston rod) Rod cross section ore M E 0 M x. M x. M x. M x. M x. M x. øc øcd H ød EE E 0. M x 0.. M x 0.. M x 0.. M x 0. G /. G / G H 0 HR 0 0...... 0. M x 0. M x 0. M x M x M x. M0 x. V N N ønd h..... 0... 0.. RR 0 0 S 0 0 U H ore to 0.(0.) 0.(.) 0(.) (.). ( ): In the case of auto switch style. S Z to 00 0(0.) 0 to 0 (.) to 0.(00.).(.) (.) (.) to 00 (.) 0.... 0 to 0 (.) 0. to 0.(.).(.) (.) 0(0.). XC to 00 (.). ZZ 0 to 0 (.) to 0 0.(0.) 0.(0.) (.) (.) to 00 (.) 0. 0.. 0 to 0 (.). --
ISO Cylinder: Standard/Non-rotating Type Single cting, Spring Return/Extended Series C Dimensions with Mounting racket Single acting, Spring extended CN, CE Rod foot, Rod and head foot: CL0, CL, CL + Stroke LT CN, CE Rod flange, Head flange: C0, C, C CN, CE Rod trunnion, Head trunnion: CT0, CT, CT CN Clevis: CC0, CC, CC ore 0 NH T U TR US Head cover E T U H H Head cover E Head cover N TM TZ TD e U Head cover E TM TZ TD e U Head cover N NH E NH LT U Head cover N TR US Head cover N T + Stroke XV + Stroke ront foot, Rod and head foot TT XC + ( x Stroke) XS + Stroke XL + ( x Stroke) LS + Stroke L + ( x Stroke) Rod flange, Head flange LS XL L O US ø LT NH TR JS XS V H T T U to 0 to 00 0 to 0 to 0 to 00 0 to 0 to 0 to 00 0 to 0.....(.).(0.).(.).(.)........ 0..(.) 0..(.). (0.) 0(0.). 0 (.). 0(0.) (.) (.) (.) (0.) (.). 0 0(0.) (.) (.)........ 0 0 0 0 0.. 0 0... O TR LG CD -ø V XZ + ( x Stroke) -ø LT O T TT CJ CJ CM CG M M C CS C C C CP NC - Rod trunnion, Head trunnion Clevis ore XZ XC TT U TD e TM TZ XV øcd H E ø O U TR LG NH LT to 0 to 00 0 to 0 to 0 to 00 0 to 0 0.(.).(.)............(.)..(.) (.).... (.) 0(0.) (.) (.).... 0(0.) (.) (.) 0... 0.. 0....... ( ): In the case of auto switch style. --
Series C Dimensions Single acting, Spring extended C ore Stroke T ithout magnet, uilt-in magnet H + Stroke G ød S E EE C, CD Non-rotating (Piston rod) øc HR M V N N Rail mounting type () and mounting type () or non-magnet H + Stroke Z + ( x Stroke) S + Stroke Rod cross section ore M 0 E M x. M x. M x. M x. M x. M x. øc 0 ød..... EE M x 0. M x 0. M x 0. M x 0. G / G / G H 0 HR 0 0...... 0. M x 0. M x 0. M x M x M x. M0 x. V N.... N.. 0. 0... S 0 0 H ore S to 0 to 00 0.(0.).(.) 0(.) (.). (.). ( ): In the case of auto switch style. 0 to 0 (.). to 0.(.).(.) 0(.) 0(0.). Z to 00 (.). 0 to 0 (.). --
ISO Cylinder: Standard/Non-rotating Type Single cting, Spring Return/Extended Series C Dimensions with Mounting racket Single acting, Spring extend Rod foot: CL0, CL, CL + Stroke LT NH -ø CJ TR JS O V CJ US XS + Stroke CM Rod flange: C0, C, C CG M M T U C CS C C T C + Stroke CP Rod trunnion: CT0, CT, CT NC TM TZ - TD e TT U XV + Stroke ore 0 O US ø...... LT.. NH Rod foot TR JS 0 0 XS.. 0 V.. 0 0 Rod flange H...... T.. T 0 0 0 0 U 0 0.. TT U Rod trunnion TD e TM TZ XV --
Series C uto Switch Mounting Position and Mounting Height Single acting, Single return (and mounting type) (Rail mounting type) C C0 0.. CC C0C. H 0H 0.. H H HL HN.. C 0C. ø0. HC.. uto Switch Mounting Position uto switch model C C0 CC C0C 0 H/0H C/0C /J /J V V JC/ L H HC H HL HN ore 0 0 0 0 0 to 0 st.. () ()...(.).(.).. () ().. () (). () () to 00 st......... Single acting/spring return ( ) for non rotating type. The lower of ø is a number for CD/Y. im at this number. -- 0 to 0 st............ 0 0 0.... 0...... J J L JC. V V VL. ø0 C uto Switch Mounting Height ore 0 C/C0 H H HL HN Hs... im at this number. CC C0C Hs... 0 Hs.... H/0H /J /J L Hs.... C 0C Hs.... HC JC V V VL Hs. Hs Hs.. Hs..
ISO Cylinder: Standard/Non-rotating Type Single cting, Spring Return/Extended Series C uto Switch Mounting Position and Mounting Height Single acting, Single Extended (and mounting type) (Rail mounting type) C C0 0. CC C0C H H HL HN HC uto Switch Mounting Position uto switch model C C0 CC C0C 0 H/0H C/0C /J /J V V JC/ L H HC H HL HN ore 0 0 0 0 0......... Single acting/spring extended to 0 st................... to 00 st.................. 0... 0 to 0 st................... C uto Switch Mounting Height ore 0 C/C0 H H HL HN Hs... im at this number. H 0H C 0C CC C0C Hs... J J L JC V V VL 0 Hs...... H/0H /J /J L Hs..... 0.. ø0. ø0 C 0C Hs.... HC Hs.. JC V V VL Hs Hs.. Hs.. -- CJ CJ CM CG M M C CS C C C CP NC -
ISO Cylinder: Direct Mount Type Double cting, Single Rod Series CR ø, ø0, ø, ø, ø, ø How to Order Double acting Single rod C DR 0 X Nil D uilt-in magnet None uilt-in magnet Type ottom side mounting ront side mounting Only ø, ø Symbol Y Mounting style Mounting ront nose ront nose in line port uto switch mounting type Rail mounting and mounting pplicable auto switches and bands are shown on page --. Please order auto switches and bands separately. R piston rod and rod end nut Option ore size Stroke ore size Standard stroke 0 0,, 0, 0, 0, 00 0,, 0, 0, 0, 00,, 0 0,, 0, 0, 0, 00,, 0 Other strokes on request. Max. stroke 00 0 0 Mounting racket Part No. Mounting bracket Single knuckle joint Double knuckle joint loating joint ore size 0 JD JD JD J0D GM- GM-0 GM- GM0- J0--00 J--00 J J -- -0- Replacement Parts ore size Part no. C-PS C-PS Every set includes: n rod seal n seal retaining washer n retaining ring --
ISO Cylinder: Direct Mount Type Double cting, Single Rod Series CR Square rod cover makes direct mounting possible Space-saving Mounting accuracy and rigidity made possible by means of faucet joint and direct mounting. ront nose mounting type and bottom side mounting available to suit your applications. Specifications ore size Piston rod dia. Piston rod thread Port size ction luid Proof pressure Max. operating pressure 0 0 M x 0. M x 0. M x M x M x. M0 x. M x 0. M x 0. M x 0. M x 0. G / G / Double acting, Single rod ir. MPa.0 MPa CJ ottom side mounting Min. operating pressure 0. MPa 0.0 MPa 0.0 MPa mbient and fluid temperature to 0 C (uilt-in magnet type: 0 to 0 C) CJ Cushion Lubrication Piston speed Rubber bumper (Standard) Not required. Use turbine oil Class ISO VG, if lubricated. 0 to 00 mm/s CM CG ront side mounting llowable kinetic energy Stroke tolerance 0.0 J 0.0 J 0.0 J 0.0 J 0. J 0. J 0/+ 0/+. M M C ottom side mounting ront side mounting eight ore size ottom side mounting asic weight ront side mounting dditional weight for each 0 mm of stroke 0.... (g). CS C C C JIS Symbol Double cting, Single Rod CP NC - --
Series CR uto Switch Mounting, Minimum Possible Cylinder Stroke and Mounting Style ore size: ø, ø0, ø, ø C C0 uto switch model CC C0C HC H H HL HN No. of auto switches pcs. pcs. Different sides Same side Different sides Same side 0 0 0 0 0 0 pc. 0 0 0 Rail Mounting Style ore size: ø, ø0, ø, ø uto switch model /0 C/0C H 0H J V JC J L V VL No. of auto switches pcs. pcs. 0 0 0 0 pc. cannot be mounted on bore size ø, ø0, ø cylinder. 0 0 0 and Mounting Style ore size: ø, ø uto switch model C C0 CC C0C HC H H HL HN No. of auto switches pcs. n pcs. Different sides Same side Different sides Same side 0 0 + ( n ) 0 + (n ) (n =,...) + ( n ) + 0(n ) (n =,...) + ( n ) 0 + (n ) (n =,...) pc. 0 0 0 Rail Mounting Style ore size: ø, ø uto switch model /0 H/0H C/0C V J JC J L V VL No. of auto switches pcs. n pcs. 0 0 + ( n ) (n =,...) + ( n ) (n =,...) pc. 0 --0
ISO Cylinder: Direct Mount Type Double cting, Single Rod Series CR Construction Double acting, Single rod CR to (Disassembly is not possible.)!! y q r e i! o!0 C D CJ Standard ø0 to ø ront nose Y ront nose in line port u Standard ø uilt-in magnet Component Parts No. Description Material Qty. No. Description Material Qty. q C D e r Rod cover Head cover Head cover Y Cylinder tube Piston rod Piston Piston rass rass (Switch type piston) y u i o!0!!! ush umper Piston gasket Tube gasket Rod seal Piston seal Rod end nut Sintered bronze Urethane NR NR NR NR (Switch type only) ( for switch type) CR /! i y! u q r e! t!!!0! o C D! CJ CM CG M M C CS C C C CP NC - Standard ront nose Y ront nose in line port uilt-in magnet Component Parts No. Description Material q C D e r t y u i Rod cover Head cover Head cover Y Cylinder tube Piston rod Piston Plain washer ush Retaining ring Sintered bronze Qty. Hard chrome plated Chromate No. o!0!!!!!!! Description Retaining ring ear ring umper umper Piston gasket Rod seal Piston seal Rod end nut Material Resin Urethane Urethane NR NR NR Qty. (Switch type only) --
Series CR Dimensions Double acting, Single rod ase mounting/cr Y to Stroke ithout magnet, uilt-in magnet (and mounting type) X ød ød S H G EE EE G -øld M øc N N LX LH H S + Stroke L Head cover Y Head cover ZZ + Stroke ore M 0 øc ød EE M x 0. M x 0. M x 0. M x 0. G G H M x 0. M x 0. M x M x L øld ø., ø. depth of counterbore ø., ø. depth of counterbore ø., ø depth of counterbore ø., ø depth of counterbore LH 0 0 LX N N S..... 0... 0.. S H 0 0 X ZZ ase mounting/cr Y / Stroke ithout magnet, uilt-in magnet (and mounting type) ød ød S øc X H G E EE G -øld ønd LH Head cover Y Head cover M H N S + Stroke ZZ + Stroke N LX L ore M.. øc ød EE G / 0. G / G G H L øld M x.. ø., ø. depth of counterbore. M0 x. ø., ø depth of counterbore. LH LX N N ønd h S 0 0.0 0 0.0 S H 0 X ZZ 0 ront mounting/cr Y / Stroke ithout magnet, uilt-in magnet (and mounting type) ød ød S øc H G EE EE G -ø ønd M N N X Head cover Y Head cover H S + Stroke ZZ + Stroke ore M øc ød EE G /. 0. G /. M x 0. depth M x depth X G G H M x. M0 x. N N ønd h 0 0.0 0 0.0 S S H 0 ZZ 0 --
ISO Cylinder: Direct Mount Type Double cting, Single Rod Series CR uto Switch Mounting Position and Mounting Height Double acting, Single rod (and mounting type) (Rail mounting type) C C0 0. CC C0C H H HL HN HC uto Switch Mounting Position ore 0 C H/0H H C0 0 C/0C HC CC /J H C0C /J HL V HN V JC/ L........................ H 0H C 0C J J L JC.. V V VL 0... ø0. ø0. CJ CJ CM CG M M C CS C C C CP NC - C uto Switch Mounting Height ore 0 C/C0 H H HL HN Hs... im at this number. CC C0C 0 H/0H /J /J L C 0C HC JC V V VL Hs Hs Hs Hs Hs Hs Hs Hs.................... --
Series C pplicable uto Switch Type Reed switch Solid state switch Special function Diagnostic indication (-color) Diagnostic indication (-color) ater resistant (-color) ith timer ith diagnostic output (-color) Electrical entry Grommet Connector Grommet Grommet Connector Grommet Indicator light Yes No Yes No Yes Yes iring (Output) -wire (NPN) -wire -wire (NPN) -wire (PNP) -wire -wire -wire (NPN) -wire (NPN) Load voltage DC V V V, V V V V, V V, V V -wire (NPN) V, V -wire (PNP) V Lead wire length symbols: 0. m Nil (Example) CC m Z (Example) CCZ m L (Example) CCL None N (Example) CCN V V, V Solid state switches marked with are manufactured upon receipt of order. cannot be mounted on bore size ø, ø0, ø cylinder. C 0 V 00 V 00 V V uto switch model Lead wire length and Rail mounting 0. None mounting Perpendicular In-line () (L) (Z) (N) C C C0 CC C0C H H H HC HN HP H H HN 0 C 0C NV PV V JC NV V V H H H 0H P J P J NT pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PLC Relay, PLC --
uto Switch Series C Mounting racket and mounting type <pplicable auto switch> C/C0, CC/C0C, H, HC Mounting and Moving Method of uto Switch Mounting racket Rail mounting type <pplicable auto switch> /0, C/0C, /J, JC Mounting and Moving Method of uto Switch. Put a mounting band on the cylinder tube and position the auto switch.. Put the mounting part of auto switch in the middle of the stationary fitting, aligning the mounting hole with the hole of the stationary fitting.. Screw in the auto switch mounting screw through the mounting hole into the threaded part of the band fitting.. Set the whole body to the detecting position by sliding, then tighten the mounting screw to fix the auto switch (the tightening torque of M screw should be about 0 to 00 N/cm).. Modification of the detecting position should be made following step #. uto Switch Mounting and Part No. Series C J-00 The distance from the operating position of auto switch to the returning position is called the differential response. This response is included in part of the operating range (one side). Switch operating position (ON) 0 J-00 Switch operating position (O) ore size J-0 J-0 uto switch Differential Response of uto Switch uto switch Differential response uto switch mounting screw M x 0. x uto switch mounting band (ith bracket) M-0 M-0 The difference between the operating position (ON) of switch and the returning position (O) is mm or less in a reed switch and mm or less in a solid state switch. uto switch mounting screw Nut for fixing Maximum Piston Speed uto switch uto switch mounting rail. Slide the nut located inside the mounting rail and set it at the auto switch mounting position.. it the convex part of the auto switch mounting arm into the slot of the rail and slide it to the nut position.. llow the auto switch mounting screw to match gently in the nut for attachment and screw it in.. Check the detecting position again and tighten the mounting screw to fix the auto switch definitely (the tightening torque of M screw should be about 0 to 0 N/cm).. Modification of the detecting position should be made following step #. If an auto switch is set at mid-stroke, the electrical device to which it is connected, may not operate if piston speed is too high. Maximum allowable piston speed V is given by V (mm/s) = Example The operating range of a L reed switch on a CDE0 cylinder is mm. It is necessary to use a solenoid valve with an electrical response time of ms. Maximum piston speed, V = x 000 = mm/s Operating Range of uto Switch Mounting and Rail Operating range of auto switch Response time of electrical device (ms) Model C/C0/CC/C0C H/H/HL HC /0, H/0 C/0C /J//J V/V/ JC/ 0 x 000 ore size 0. 0.. CJ CJ CM CG M M C CS C C C CP NC - --
Series C Contact Protective ox CP, CP / and C/C reed switches do not incorporate contact protection circuits. Contact protection is required if:. Operating load is inductive.. The wiring length to load is m or more.. Load voltage is 00 VC or more. Contact Protective ox/specifications Part no. CP CP Load voltage 00 VC 0 VC VDC Max. load current m. m 0 m Lead wire lengh Switch connecting side 0. m Load connecting side 0. m Contact Protective ox/internal Circuit CP CP Surge absorber Choke coil Choke coil rown lead wire (~) lue lead wire (+) rown lead wire ( ) lue lead wire Contact Protective ox/dimensions Connection Method of Contact Protector, Connect lead wires from reed switch to those on protector box indicated with switch. Length of lead between switch body and protector should be less than m., CP VOLT ø. switch, --
Option Series C High Temperature X Low Temperature X C Mounting ore size Stroke X N, E,, Y, 0,,,, mm Standard cylinder seals are replaced with special ones and other modifications are made in order to enable the cylinder to operate at a high ambient temperature ( 0 to 0 C). C Mounting N, E,, Y, mm ore size Stroke X Standard cylinder packing are replaced with special ones and other modifications are made in order to enable the cylinder to operate at a low ambient temperature ( to 0 C). Possible applications: - ore size to mm - Rubber bumper - ithout magnets (uto switches cannot be used at high temperature.) - Single rod Double acting - Double rod Double acting () Dimensions unchanged Specifications Type pplicable size ction mbient temperature range Piston speed Cushion Material Grease ) Contact SMC for non-rotating type. C Mounting ir cylinder ø, ø0, ø, ø, ø mm Double acting 0 to 0 C 0 to 00 mm/s Rubber bumper Seal: luorocarbon rubber ear ring: luorocarbon resin luorinated grease ore size Stroke X Possible applications: - ore size and mm - Rubber bumper - ithout magnets (uto switches cannot be used at low temperature.) - Single rod Double acting - Double rod Double acting () Dimensions unchanged Specifications Type pplicable size ction mbient temperature range Cushion Material Grease ir cylinder ø, ø mm Double acting to 0 C Rubber bumper Seal: Low nitrile rubber ear ring: luorocarbon resin luorinated grease Low Speed X Heavy-duty Scraper XC N, E,, Y, mm The cylinder does not generate any stick-slip phenomenon even at the rated low speed of 0 to 0 mm/s. ll strokes drive at a constant speed smoothly. Possible applications: - ore size and mm - Rubber bumper type only - ith or without magnets - Single rod Double acting Dimensions unchanged Specifications Type pplicable size ction Piston speed Cushion ) Contact SMC for non-rotating type. ir cylinder ø, ø mm Double acting 0 to 0 mm/s Rubber bumper ) Contact SMC for non-rotating type. C Mounting N, E,, Y, mm ore size Stroke XC heavy-duty scraper is used as wiper ring. Ideal for severe applications where the cylinder is exposed to dust, earth and sand. pplicable to casting machines, construction machines, industrial vehicles, etc. Possible applications: - ore size and mm - Rubber bumper type only - ith or without magnets - Single rod Double acting - Double rod Double acting () Dimensions unchanged Specifications Type pplicable size Max. operating pressure Min. operating pressure Cushion iper ring ) Not applicable for non-rotating type. Construction ir cylinder ø, ø mm MPa (0 bar) 0.0 MPa (0. bar) Rubber bumper NR (SC) CJ CJ CM CG M M C CS C C C CP NC - --