BMW7246 Puller / BMW7246-2 Installer For R&R the Thrust Arm (bracket) from/to the Front Control Arm on BMW E30, E36, Z3, E46. Thrust arm bushing# 31129063163 BMW334-190 Rear Wheel Carrier Kit For R&R ball joint on Rear Wheel Carrier (Lower Steering Knuckle) on BMW E38, E39, E52, E53, E60, E65, E66, E67, E70 TTS1941 Spring Compressor Strut spring compressor for the MacPherson struts. Designed to fit securely around the spring and protect the spring from damage. ( Front & Rear axle springs) Spring specification: A: dia. 190-140 B: dia. 140-110 C: dia. 110-75 B Applicable: BMW, VW, Audi, Volvo, Porsche, SAAB, Japanese cars, C BMW1941-E39/E46 Spring Dumper R&R Kit Used to fix on the top of the spring cap, avoid falling off when working on the spring on BMW E39, E46 (Use it together with TTS1941) A M204-212 Fuel Tank Lid Remover For R&R the locking ring of the fuel tank delivery sensor unit on BMW F01, F02, F10, F12, Mercedes: W204, W207, W212 TTS1385 Fuel Tank Lid Remover For R&R the locking ring of the fuel tank delivery sensor unit on BMW F01/F02/X3/F25 BMW161-020 Fuel Level Sending Unit For R&R the locking ring of the fuel tank delivery sensor unit on BMW E31, E34, E36/7, E38, E39, E46, E52, E53, E60, E61, E63, E64, E65, E66, E67, E83, E85, E87, R50, R52, R53 B-M203 Fuel Level Sending Unit For removing the plastic fuel tank lid on BMW E36/E46 Mercedes-Benz 211/203, VW-Audi TTS1312 Universal Fuel Tank Lead Remover BMW1941-E38 Spring Dumper Set Extra large Disc set for BMW E38 Range:180mm-240mm Use it together with TTS1941 spring compressor kit TTS1251-16mm Spark Plug Socket 3/8" Drive 16mm, length 93mm, outer dia: 22mm, spark plug socket with retaining spring and joint. Applicable: Mercedes M112, 113, 137, 155, 166, 271, 272, 273, 275, 902, 906, BMW X6, TTS2151-14mm Spark Plug Socket 14mm 12 point 3/8 drive BMW spark plug socket for 2007 and later BMW 135, 335, 535 and X6 with 3.0l twin-turbo, and 2007 and newer turbo charged Mini Coopers

BMW112-170 Flywheel Lock For locking flywheel with transmission installed on BMW M20, M21, M40, M41, M42, M43, M44, M47, M50, M51,M52, M54, M56, M57, S50B30, S50B32, S54 TTS4750 Universal Flywheel Lock Special design for locking the flywheel when the gearbox is dismounted. This tool can be adjusted axially and radically for almost universally by screwing in different stud bolts. Opening range: 92-107mm TTS1156 Spring Pliers For removing and installing the spring on BMW N42, N46 BMW170-030 Oil Cooler Line Pliers For releasing the hydraulic cooling lines on BMW E46, E53, E60, E61, E64, E65, E66, E70, E81, E83, E85, E86, E87, E90, E91, E92, E93, R50, R52, R53, Rr1, BMW112-120 Flywheel Lock For locking flywheel with transmission installed on M30, transmission: 3HP20, 3HP22, 4HP22 - Automatic transm. BMW118-180 Flywheel Holder Blocking flywheel when releasing and tightening down central bolts on vibration damper, when replacing timing chain on M47T2, M47TU, M57T2, M57TU, M67, N45, N45T, N46, N46T, N51, N52, N53, N54, N55, W17 BMW117-110 Intermediate Valvetronic Lever For removing and installing pressure spring for intermediate levers on BMW N20, N51, N52, N52K, N52T, N55, engines Fits the newer VVT spring block that is 58 mm wide. TTS1206 Ball Joint Separator 24 mm for splitting track-rod end, anti-roll bar mountings,ball joints,... Especially in confined space conditions like on BMW E39 BMW312-240 Ball Joint Puller Kit 24/27/31/36mm For quick & easy separation of ball joint connections. BMW: E38, E39, E52, E53, E60, E61, E70, E83, E90, E91, E92, R50, R52, R53, RR1, RR2, X5 Mercedes: E-Class (W211), CLS (W219), S-Class (W220),SL-Class (W230) Audi: A4, A6 Carrera lower suspension ball joint TTS2236 Glow Plug Socket Set TTS1376 Universal Valve Spring R & R Kit Replace valve spring and oil seal of valve rod on car, without removing head gasket. Works great in the narrow engine room. Enormous time saving for replacement of valve stem seals. Special design helps compress valve spring regardless of firewall barrier. Applicable: BMW N42, N52, N54, N62, N63, M54, M52, M56, M60, Mercedes M102, 103, 104, M111, 112, 113, 271, 272, 273

BMW332-110 Output Shaft Kit (Including: BMW332-110, B MW332-150, BMW335-070 For removing and installing output shaft in drive flange as well as for removing front wheel bearing unit. Applicable: BMWE30, E31, E32, E36, E38, E39, E46, E52, E53, E60, E63, E64, E65, E66, E67, E83, E85, RR1 (On E53 used in conjunction with BMW332-150) BMW332-150 Spacer Ring For R&R output shaft in drive flange front and rear as well as for removing front wheel bearing unit on BMWE53 (Used in conjunction with BMW332-110) BMW335-070 Holding Lever Pull-out extension for BMW332-110, BMW335-040, BMW335-050, BMW335-060 BMW38-39 Hydraulic Bushing Kit For R&R the rubber mount in the front Trailing Arm (Traction Strut, Upper Sub-frame) right on the car on BMW 5 series (E34, E39), 7 series (E32, E38, E65, E66) 8 series (E31) X5 (E53) E83, E87, E70, E90, E91, E92, E93, M3, Bushing numbers# E32, E31: 31121-136607, E34: 31121-139456, E38: 31120-006482, E39: 31129068753, E53: 31121-096372 until 01/05 new#31126-769715, E60, E65, E66: 31120-303754, E 31, E32, E34 E65,E 66 E 38,E39 B90A Front Wheel Bearings/Hub Puller Kit For removing and installing front wheel bearings with the spindle on the car Applicable: Mercedes-Benz, BMW, VW/Audi, Porsche,Volvo, Toyota/Lexus, Nissan Infinity, Honda/Acura,other Asian makes, B90K Wheel Bearing Kit For removing and installing front and rear wheel bearings out of the hub while still on the car. Application: Mercedes Benz, BMW, VW, Toyota, Ford, Volvo Could be work with shop press also. TTS1089 Universal Axles Oil Pressure Extractor (Replaceable) Hydraulic hub puller with 4 and 5 hole plates. 5 holes for European Cars, Benz, BMW, VW-Audi... 4 holes for Japanese cars, Honda, Toyota... work with any kind of a general pump (not included)

BMW2336 Rear Axle Carrier Bushing Kits For R&R the Rear Axle Carrier Mount Bushings w/o completely lowering the rear axle assembly on BMW E39, E46/E85, E53, E87, E90 BMW333-360 Rear Sub-frame Differential Kit For R&R rubber mount in bottom of rear axle carrier, threaded connection of rear axle differential on BMW E46, E83/ X3, E85, E86 / Z4 (right on the car) Bushing number: 33171093175 (old number) 33176770788 (new number) BMW2336/E87/E90 E46/E85: BMW E46, E85 Bush#:33 31 092-515/516/517 TTS389-008 Rear Axle Carrier Front/ Rear Suspension Differential Bushing Kit For R&R the front and rear suspension differential bushings on BMW E38, E39. Front Bushing# 33171090389 Rear Bushing# 33171093008 BMW2336-E53: BMWE53/X5 Bush#:33 31 1 770 454 E39 Sedan/Wagon BMW2262 Front Upper Bushing Kit Suitable for the removal / installer of the upper sub frame bushing BMW E90/M3. Can be used in-situ without removing the arm from the car. Bushing No. 31120393540K / 31126763719, 31102283579. Application: BMW 90 / M3 BMW334-180 Rear Suspension Differential Bushing Kit Replacing All Rubber Mounts for front final drive suspension For removing and installing rubber mount in bottom of rear axle carrier, threaded connection of rear axle differential on BMW 3 E46/E83 (X3), E85/E86 (Z4) Bushing numbers: 33317 6 751 808 (new) 3317 1 093 565 (old) TTS1487 Lower Control Arm Bushing Kit For BMW E87, E90, E93 and M3 BMW1054 Suspension Bushing Master Kit For R and R Rubber Suspension bushing ons BMW cars 1Series (E81/87), 3Series (E36/46/83/90/91/92/93), 5Series (E60/61), 6Series (E63/64), 7Series (E38/65/66/67), 8Series (E31), Z4 Series (E85/86), Mini Cooper S, R53

BMW244-110 5HP-24/5HP30 Socket 6 pin grooved nut socket for R&R slotted nut on the output shaft flange TTS1332 Front Camber Adjuster Kit Adjust the front camber on late model 3 series with KDS Applicable: BMW E38, E39, E46, E53, E65, E66, E67, E81, E83, E85 E87, E90, E91, E92, E93 BMW241-170 Transmission Socket 5HP18 / 5HP19 For R&R slotted nut on the output flange TTS1438 Front and Rear Oil Seal R&R Kit For removing and installing the front and rear crankshaft seal on BMW N40 N42, N45, N45T, N46, N46T, N52, N53, N54 TTS1512 Front Crankshaft Oil Seal R/R Kit Used to loosen the seal for removal and installation of new front crankshaft seals on BMW N40, N42, N45, N46, N52, N53, N54, N55 TTS1352 BMW Line Disconnect Tool Power steering and Transmission Line Disconnect tool for 1999-2005 BMW 3-Series and X5 Also covers the transmission cooler line BMW221-010 Transfer Case Bushing Mount Kit For R&R the transmission rubber mount bushing on BMW X1/X3 (up to2003) X5 1999-2006 BMW112-450 Crankshaft Counter Holder For locking hub in position when releasing and tightening central bolt on BMW E31, E32, E34, E38, E39, (M60, M62) BMW119-280 Holder For crankshaft when releasing/tightening central bolt on BMW N12, N14, N40, N42, N45, N46, N52 (when replacing timing chain) TTS2095 Transfer Case Bushing Mount Kit For R&R the transmission rubber mount bushing on BMW X5 1999-2006 BMW112-150 Crankshaft Counter Holder Locks crankshaft vibration damper to allow removal of crankshaft bolt with the engine in or out of the car. Applicable: M20, m40, M41, M43, M44, M50, M51, M52 Use with shim 112-410 for M41, M42 and M52 engines. BMW118-190 Holder/Brace/Hub Puller For gripping vibration damper when removing retaining bolts on BMW M52TU, M54, M56 Kit including: BMW118-200, BMW118-210

BMW M52 Big Camshaft Alignment Kit Master tool set contains a comprehensive set of tools to perform camshaft + VANOS timing on M52TU, M54, M56 Engines. The tools are also applicable for camshaft timing on non-vanos engines ( M42, M44, M50, M52, MS50US and S52US). Including: BMW113-240 Camshaft Locking Tool Kit, BMW112-300 Locking Pin, BMW116-150 Camshaft Tool BMW116-180 Fixture, BMW114-220 Chain Tensioner BMW113-450 Banjo Fitting BMW115-490 Sprocket BMW119-291 Pin NST2022 VANOS Cam Timing Kit Including:BMW118-200, BMW116-150, BMW116-180, BMW114-220, BMW113-450 NST2008 Camshaft Timing Master Kit Kit Including: BMW112-440 for M60, M62 engines, BMW113-240 for M42, M44, M50, M52 engines, BMW113-190 for M40, M43, M70, M73 engines BMW112-300 Locking Pin BMW114-230, and BMW113-190 Chain Tensioners BMW M60-62 Big Camshaft Timing Kit Kit Including: BMW 112-440 Locking Fixture For locking camshaft in position when adjusting timing on BMW M60, M62, M62Van,M62TU, BMW116-450 Locking Fixture (1999-2002) For fixing camshaft sensor wheel in position during assembly on BMW M62 VANOS BMW117-380 Tensioning Bracket For screwing in chain tensioner with top right timing case cover removed on BMW M62, M62VAN BMW116-420 Socket Wrench WAF32 For removing and installing solenoid valves on BMW M54, M62 VANOS, BMW116-440 Hook Wrench For adjusting VANOS to left stop during assembly as well as for adjusting valve timing on M62 VANOS BMW115-180 Locking Pin For locking flywheel in TDC position on M62, M62VAN BMW114-230 Chain Tensioner For tensioning primary chain when adjusting valve timing M60, M62, M62VAN. BMW112-300 Locking Pin For locating crankshaft in ignition TDC position in order to adjust valve timing on M60, M62 BMW113-420 Locking Clip Set For secondary chain tensioner (2) to lock chain tensioner piston in position, e.g when removing and installing sprockets on M60 BMW113-290 Locking Pin Set TTS2092 Variable Camshaft Timing Kit Variable camshaft timing tool kit. Checking or adjustment of timing. Applicable:M40,M43 Twin camshaft M42, M44, M50/52/54/56 BMW112-400 Tensioning Bracket For Screwing in chain tensioner with top right timing case cover removed on BMW M60 VAN BMW113-290 Locking Pin Set For secondary chain tensioner to lock chain tensioner piston e.g. when removing and installing sprockets on M50, M52, M 54.

BMWN51, N52, N53, N54, N55 Camshaft Timing Kit / Build your own version BMW119-340 Chain Tensioner To tension the primary timing chain on BMW N40, N42, N45, N46, N51, N52, N53, N54, N55, engines when setting valve, camor VANOS timing BMW110-300 Locking Pin For locking flywheel in TDC position on N51, N52, N53, N54... BMW118-520 Gauge For disconnecting camshaft sensor gears when adjusting timing on BMW N53, N54 BMW114-290 Gauge For disconnecting camshaft sensor gears when adjusting timing on BMW N51, N52, N52K, N55, BMW114-280 Gauge For rotating camshaft in TDC Position on N51, N52, N53, N54 BMW114-285 Camshaft Top Plate To lock the camshaft in Top Dead Center when adjusting the valve timing on BMW N55 engines (F07, F10 * 535i, 535iX, Hybrid5) BMW114-450 Locating Fixture For locating guide blocks during installation on the BMW N52 BMW114-280/285/290 Camshaft Timing Kit with BMW114-460 Locating Fixture For locking camshaft in TDC position when checking/ adjusting camshaft timing, replacing inlet camshaft or timing chain on BMW N51, N52, N52K, N53, N54, N55, E60 (523i, 523Li, 525i, 525Li, 525xi, 528i, 528xi, 530i, 530Li, 530xi, 535i, 535xi), E61 (523i, 525i, 525xi, 530i, 530xi, 535xi), E63 (630i), E64 (630i), E65 (730i), E66 (730Li), E70 (X5 3.0Si), E81 (130i,) E82 (135is), E83 (X3 2.5i,2.5Si, 3.0i, 3.0Si), E85 (Z4 2.5i, 2.5Si, 3.0i, 3.0Si), E86 (Z4 3.0Si) E87 (130i), E90 (323i, 325i, 325xi, 328i, 328xi, 330i, 330xi, 335i, 335xi), E91 (323i, 325i, 325xi, 328i, 328xi 330i, 330xi, 335i, 335xi), E92 (323i, 325i, 325xi, 328i, 328xi, 330i, 330xi, 335i), E93 (325i, 328i, 330i, 335i) F01, F02, (740i, Hybrid7, 740Li, 740LiX, Hybrid7L, F07, F10 (535i, 535iX, Hybrid5), F12, F13 (640i, 640ixdr) F20, F21 (M135l, M135lXD), F22, F23 (235i), F31 (335i, 335iX), F32, F36 (435i xdr), X Series (X35i, 40iX...) BMW114-460 Locating Fixture For locating upper and lower bearing stip when installing exhaust camshaft on N51, N52 Complete Kit including: BMW114-280 (114-281, 114-282, 114-283, 114-284, 114-285) BMW114-290, BMW110-300, BMW118-520, BMW114-460 (114-461, 114-463, 114-463) BMW114-461/462 Locating Fixture For locating upper and lower bearing strip when installing exhaust camshaft on N51, N52 BMW118-550 Exhaust Valve Spring Compressor For holding the bearing strips in place when fitting intake camshaft on BMW N54/N54T/N55 BMW114-280/114-460 Camshaft Timing Kit For locating camshaft in TDC position when checking/adjusting camshaft timing, replacing inlet camshaft or timing chain. Kit also including the fixture for locating upper and lower bearing strip when installing exhaust camshaft on BMW N51, N52 engines. Per request the BMWN55 kit also available separately

BMW119-450/460 N62, N73 Big Kit For locating camshaft in TDC position when checking or adjusting camshaft timing on BMW N62, N62TU, N73 E53 (X5 4.4i, 4.8is), E60 (540i, 545i, 550i), E61(545i, 550i), E63 (645 Ci, 650i), E64 (645Ci, 650i), E65 (735i, 740i, 745i, 750i, 760i, AlpinaB7), E66 (735Li, 740Li 745Li,750Li, 760Li) E70 (X5 4.8i), Including: BMW119-461/462 Cam Lock, BMW117-270 Socket for releasing & tightening VVT intermediate shaft on N73 BMW119-190 Plug Mandrel for locking flywheel in TDC position on N62, N62TU, N73 BMW119-463 Holder with Screw BMW119-450 Counter Holder with Socket, and pointer for gripping charnkshaft when releasing/tightening central bolt on N62, N62TU, N73 Angle Position Gauge (protractor) for fitting on brace 112-450 (M60/M62), 112-420 (M73) or 119-450 (N62/N73) when tightening central bolt using trosion angle tightening method. BMWN63-74 Camshaft Alignment Master Kit Checking / adjusting camshaft timing on N63 (F-6 series), S63 (X6 E70, E71) N74 (F-7series) Kit including: BMW 119-190, BMW 119-900, BMW 118-570, BMW118-090, BMW 119-890, BMW114-480 Plastic case is included BMW119-450 Counter Holder with Pointer 27mm Socket and Disc with hexagon screw For gripping crankshaft when releasing/tightening central bolt on BMW N62/N62TU/N73 BMW113-460 Angle Position Gauge/Protractor For fitting on brace 112-450 (M60/M62), 112-420 (M73) or 119-450 (N62/N73) when tightening central bolt using torsion angle tightening method on M60, M62, M73, N62, N62TU, N73 NST2079 N63 Camshaft Alignment Kit Applicable: All N63 engine from 2009 (F series) Factory tool numbers: BMW119-890, 118-090, 118-570, 119-190 Models: 750i, 750ix, BMW Alpina - F01 series 750Li, 750Lix, BMW Alpina - F02 series active hybrid 750Li, 750i, - F04 series 550i, 550ix, - F07 series 550i - F10 series 650i - F12 series 650i - F13 series BMW117-270 Cylinder Head Socket For releasing and tightening VVTintermediate shaft on BMW N73 BMW119-460 Cam Timing Kit for N62/N73 For setting timing on cams of both cylinder head. Kit including: BMW119-190, BMW119-461/462/463 BMW114-460 Camshaft Locating Tool Used for locating the upper and lower cam bearing strips when installing the exhaust camshaft on BMW models with the BMW N51, N52 engines (6 cylinder).

BMW-S65 Camshaft Timing Tool Kit To locate the camshaft in TDC position and correct the VANOS angle on 2008-13, BMW M3 E90/E92/93 with S65 engine 2009-Present Wiesmann MF4-S GT/Roadster Kit including: BMW119-970 cam lock (updated version), BMW115-370 Locking Device (updated version) BMW115-320, Pin, BMW112-300 Pin TTS1477 S54 Camshaft Alignment Kit Applicable: E46/M3 (S54) Cabriolet 2000-2006, M3 (S54) Sports coupe 1999-2006, M3 CSL (S54) Sport Coupe 2003-2004 E85/Z M Roodster 2005-2007,E86/Z M Coupe 2006-2007 Kit including: BMW119-140 Camshaft Timing Gauge For checking camshaft timing when installing VANOS adjustment unit, BMW119-130 Camshaft Lead Angle Gauge For setting camshaft lead angle (1.5 degree)when installing VANOS adjustment unit on S50B32 and S54, BMW119-170 VANOS Spacer For set up the VANOS unit, BMW117-340/342 Pin, BMW115-100Adapter For turning engine at crankshaft when adjusting valve timing, BMW117-160 VANOS Spanner Wrench, BMW112-300 TDC Pin BMWN42-N46 Camshaft/Carrier Bracket Remover/Installer Kit Including: BMW119-320, BMW119-310, BMW119-300 BMW Torsion spring Remover/Installer BMW 119-290 Camshaft Timing Kit For locking camshaft in TDC position when checking/adjusting timing, or replacing inlet camshaft on BMW N42, N46 N46T E46(316i, 316ti, 318Ci, 318i, 318ti), E60 (520i, E81(118i, 120i), E83 (X3 2.0i),E85 (Z4 2.0i), E87(118i,120i), E90 (318i, 320i) E91 (318i, 320i) E92 (320i), E93 (320i), Kit including: BMW112-300, 119-290, 119-190, 119-340, 119-350, BMWN40-45 Camshaft Timing Kit For checking /adjusting camshaft timing, Removing/installing inlet camshaft on N40, N45, N45T 116 1.6i (E81/E87), 316 1.6i, (E46/E90) 316 1.6Ci (E46), 316 1.6ti (E46) Kit including: BMW117-250 Camshaft Kit BMW117-260 Gauge, 1199-190 Pin, BMW119-340 Chain Tensioner BMW118-760 Camshaft Alignment Kit For securing camshaft at TDC on N47, N47S 2.0 Diesel engines (E60, E61, E81, E82, E83, E87, E90, BMW 119-290 BIG Camshaft Timing Kit For locking camshaft in TDC position when checking/adjusting timing, or replacing inlet camshaft on BMW N42, N46 N46T E46(316i, 316ti, 318Ci, 318i, 318ti), E60 (520i, E81(118i, 120i), E83 (X3 2.0i),E85 (Z4 2.0i), E87(118i,120i), E90 (318i, 320i) E91 (318i, 320i) E92 (320i), E93 (320i), Kit including: BMW119-290, 119-190, 119-350, 119-300, 119-310,

BMW60-63/S85 Camshaft Alignment Kit BMW115-300:For locating camshaft in TDC position when checking/adjusting camshaft timing on BMW engine S85 Series: E60 (M5), E61 (M5), E63 (M6), E64 (M6) Kit incl: BMW115-301 gauge, cylinders 1-5, BMW115-302 gauge, cylinder 6-10, BMW115-320: For blocking crankshaft in TDC position when checking/adjusting camshaft timing on S85 engine BMW115-100: For turning over engine at crankshaft when adjusting VANOS timing on S50B30, S50B32, S54, S85 engines BMW115-380:For VANOS basic setting on S85 engine Kit incl: 115-381 gauge cylinders 1-5, 115-382, cylinders 6-10 BMW115-410: For VANOS removal on BMW engine S85 BMW116-320 Camshaft Alignment Kit For locking camshaft in position when adjusting timing/replacing camshaft on M47,M47T2, M47TU, M57, M57T2, M57TU, Diesel 2.0 d, 3.0 d BMW models: E38, E39, E46, E53/E70 (X5), E60, E63, E83(X3), E87, E90/91,92,93, Land Rover Freelander (Td4), Range Rover (Td6), BMW-N43 Camshaft Timing Tool Kit Engine Timing Tool Kit for BMW 1/3/5 Series with chain driven engines Includes Vanos sensor alignment tool BMW 1 series E81/82/87/88, 3 series E90/91/92/93 and 5 series E60/E61 Engine Codes: N43 B16A/AA, N43 B20A/AA and N43 B20AY 2006 onwards BMW118-690 Gauge: For locating camshaft at TDC position BMW118-700 Gauge: For locating balancing shafts BMW118-710 Gauge: For disconnecting VANOS sensor gear BMW119-340 Chain Tensioner: for tensioning timing chain when adjusting camshaft timing BMW113-340 Locking Pins: for locking chain tensioner piston in position (e.g. when removing and installing cylinder head) as well as for locking drive belt tensioner BMW115-120 Plug Mandrel: for locking flywheel in TDC position BMW119-330 Gauge For locking balancing shafts in firing TDC position on BMW N40, N42, N45, N46 BMW115-140 Locking Fixture For securing balancing shafts on BMW N45, N46, N46T BMW113-190 Camshaft Tool For locking camshaft in position when adjusting timing on M40, M43, M43TU, M70, M73. For V-12 engines you must buy 2 blocks. BMW345-311-009 Rear Axle Bushing R & R Kit (Rear Axle Support) For R&R the rubber mounts in the Rear Axle Carrier Trailing Arm (Semi-trailing arm) on E36, E46, E85 BMW345-311-009/#1 Ball Joint in Semi Trailing Arm E36, E46, E85 (Z4) Ball joint: 33321138722, 333211403345 - older mumbers - 33326775551 - new bushing number - BMW345-311-009/#2 Ball Joint in Trailing Arm for lower control arm E36, E46, E85 (Z4) Ball joint: 33321136311 - old number, 33326771828 - new number - BMW345-311-009/#3 Trailing Arm (front) Kit E36, E46, E85 (Z4) Trailing arm front: 33321097009 -old number, 33326770786 - new number

BMW119-270 Spanner For rotating camshaft on BMW N42, N46, N46T BMW115-120 Plug Mandrel For locking flywheel in TDC position on BMW N45, N45T, N46, N46T BMW112-300 Locking Pin For locating crankshaft in ignition TDC position in order to adjust valve timing on M21, M40, M41, M42, M43, M44, M47, M50, M51, M52, M54, M57, M60, M62, M67, M70, M73, S50B30, S50B32 BMW130-320 Fuel Injector R and R Tool For R&R the high pressure, direct-injection fuel injectors on BMWN20, N55 engine. N55: single turbo inline 6, produced from 2009-present featuring turbo VANOS, Valvetronic and Direct Injection. BMW9054 Injector/Chamber Tool Kit Set used to install new seals onto the injectors. Applicable: BMW N14, N18, N54 & N63 engines. Comparable to BMW Tools 130192, 130193, 130194 and 130195. BMW1488 Harmonic Balance Holder Holds vibration damper when loosening and tightening center crankshaft bolt. Application: BMW E81 120d 163PS, BMW E46 318d 116PS - 318td 115PS - 318dt 115PS - 318d 115PS - 320d 136PS - 320td 150PS - 320d 150PS BMW E90 318d 150PS - 320d 150PS - 320d 163PS BMW E91 318d 122PS - 320d 150PS - 320d 163PS BMW E39 520d 136PS BMW E60 520d 163PS - 520d 150PS BMW E61 520d 150PS - 520d 163PS BMW X3 E83 2.0d 150P3 BMW641-040 Fixture Aid to fitting power steering pump drive belt on N62 (V8) in 2004 through 2006 models with the stretch belt M271-T50 Alternator Pulley Remover 1/2" Dr, T50 Star, for assembling and dismantling the free wheel pulley while changing the alternator or pulley on BOSCH alternators on BMW, Mercedes, Audi, VW.. BMW2258 Fuel Injector R and R Tool For removing and installing the fuel injector on BMW N63 (after 2012 september) engines. BMW118-740 Removal Tool For removing high-pressure pump on BMW N47 BMW131-100 Screwdriver 5mm hex head screwdriver for setting CO value (L-Jetronic)- As from model year 1983 on BMW M10, M20, M30

BMW114-180 T60 Torx Socket For releasing and tightening dual mass flywheel. Model year as from January 1994. M60, M62, S62. Applicable: E34, E39, V8 4.0 and 4.4 L with standard transmission. BMW118-580 T60 Long Torx Socket Cylinder Head Bolt Socket for BMW N52 engines non turbo, and N54Turbo engines BMW321-110 Pin Wrench Socket For releasing and tightening nut on cylinder tube of rack and pinion steering on E30. TTS2167 Star-E Socket Set For cylinder head bolts on BMW, Mercedes CDI engines Length - 140 mm, Size: E10, E12, E14, E16, E18, E20 BMW37 Timing Chain Guide 4 and 6 cylinder Engines (Early Version, E30..) BMW600-143 Screwdriver Special 5 sided screwdriver to release anti-theft radio mount. US117-020 Oxygen Sensor Socket TTS4897 Self Ajdusting Clutch Centering Tool Special designed to reset and center the centering ring on self adjusting clutches on BMWE34,E36, E38,E39, E46, E52,E53, E85 TTS4896 Self Adjusting Clutch Installer For installing and setting self adjusting clutches on BMW E34, E36, E38, E39, E46,E52, E53, E85, Z3 BMW1842 Rail Guide Pin Puller 8 mm For removing even the most stubborn pins from the cylinder head, unlike to the short slide hammer previously used to attempt his job TTS1250 Vibration Damper Locking Tool Kit For removing and installing the vigration damper on BMW N47, N57 Kit including: BMW 117-221, 117-222, 117-223, 116-480 TTS1808 Ball Joint Separator Removes steering track rod ball joints from the steering gear (drop) arm and the steering idler arm on E24, E28, E34 Singing Power Probe The inside of may electrical parts has coil. When the vehicle power is on the magnetic power starts flow the coil, than the coil becomes magnet in a moment. At this very moment, Singing probe detect a line of magnetic force with beeping and blinking. Just touch the coiled part. Beep & Lights on? That means the part itself has no problem at all. If there is no sound or light on Singing probe, that means the part is not working or the power is off. Can test a various kind of parts: Gasoline injector, Lpi Injector, CRDi Injector, Ignition coil, Solenoid Valve, EGR Valve, ISA Valve Relay Alternator, Motors...etc.. (any parts if it is coiled inside.)

BMW616-060 Windshield Wiper Arm Remover For removing the windshield wiper arm. Special hinge allows easy access against windscreen on E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39, E46, E52, E53, E60, E65, E66, E67, E85, RR1 Oil Filter Sockets TTS2403-36: 3/8" Dr. 36 mm for OM604, 605, 606, M116 BMW M52, M60, M62, M70, M73 engines TTS2402-76: 3/8" Dr. 76 mm 12 point for BMW Motorcycles 2007-2009, M102, M103 TTS2402-86: ½"Dr. 86 mm 16 point for Volvo S40, S60, S70, S80...(from 1999-2003), BMW(316i, 318i, 2001-onwards) N40, N42, N45,N46 engines TTS1204 A/C Compressor Clutch Remover For removing the plate of clutch on BMW cars TTS1008 Radio Remover Set Use to remove and install navigation units and some radios on BMW E38, E39 BMW1412 Belt Installation Kit Special designed set of tools for installing the new belt onto the pulley on BMW, Volvo, Mazda, Ford, Chrysler, Fiat, and etc... BMW111-240 V-Belt Installation Tool Special designed for installing the V-belt without causing damage. BMW OEM number: 111 240 Applicable: BMW N52K engine (2006~2010) BMW110-330 Assembly Tool For installing elasto-belt.(v-belt) Applicable: M47T2, M47TU, M57T2, M57TU TT1017B Diesel Injector Seat Cutter Set For cleaning and repair of the sealing surfaces of injectors KIT Including: 14 x 14 mm Flat cutter, 15 x 19 mm Flat cutter, 15.5 x 15.5 mm Flat cutter, 15.5 x 15.5 mm Angled cutter, 17 x 17 mm Angled cutter, suitable for Mercedes-Benz CDI 17 x 17 mm Flat cutter, suitable for BMW, Ford, Peugeot, Citroen, Renault,Delphi and Bosch 17 x 17.5 mm Flat cutter, for various models 17 x 19 mm Flat cutter, suitable for Mercedes-Benz CRD, Bosch 17 x 19.5 mm Flat cutter, for various models 17 x 20 mm Flat cutter, for various models 17 x 21 mm Angled cutter, suitable for e.g. Fiat and Iveco 17.5 x 20.5 mm Angled cutter, for various models 19 x 21.5 mm Flat cutter, for various models T-handle, 19 x 170 mm Pilot Hex 15.5 x 250 mm Cutter, 2.5 mm Hex Key