Yakima Towers 1A Raingutter Tower Part Number: 8000101 Produced 1980 Present High Rise Tower Part Number: 8000104 1A Raingutter Tower # 8000101 + HiRise Kit # 8001101 1B Raingutter Tower Produced 1988 No Part Number Legends whisper they still roam high prairies on a dark moonless night
1A TS Custom Tower Part Number 8001100, 8001102 Produced 1992-1997 1C SST Tower Part Number 8000102 Produced 1987-1996 Railrider 1, 2, and 3 Part Number 8000201, 8000202, and 8000203 Produced 1993-1997 Q-Tower Part Number 8000105 Produced 1993-2004 Replaced in 2004 by Q-Tower #8000124
Doublecross Tower Part Number 8000110 Produced 1995-2002 WingRider 1 and 2 Part Number 8000309, 8000310 Produced 1997-1999 Locking Railrider 1 Tower Part Number 8000208 Produced 1997-2002 Crosstop Tower Part Number 8000121 Produced 1998-2001 Designed for the factory side rails of the 98-02 Subaru Forrester
X Tower A non-locking tower for the Nissan Xterra and Frontier Quad Cab Part Number 8000109 Produced 2000 2003 LowRider Tower Part Number 8000118 Produced 2001-2009 Control Tower Part Number 8000214 Produced 2002-2016 Forester Tower A non-locking tower designed for the 03-08 Subaru Forrester Part Number 8000119 Produced 2003-2006
Q-Tower Part Number 8000124 Produced 2004 2016 Replaced Q-Tower #8000105 in 2004 EZ Rider Part Number 8000130 Produced 2004-2007 LowRider MAX Part Number 8000136 Produced 2006-2009 Locking EZ Rider Part Number 8000137 Produced 2006-2009
Railgrab Tower Part Number 8000138 Produced 2009-2016 Ridgeline Tower Part Number 8000145 Produced 2016 - Present Baseline Tower Part Number 8000146 Produced 2016 - Present Timberline Tower Part Number 8000147 Produced 2016 - Present
Skyline Tower Part Number 8000148 Produced 2016 - Present
1A Raingutter Tower Shear Block 8000101 4 pack - 8810006 Shear Block Base 4 pack - 8810007 Tower Knob Single - 8880230 Kit - 8810136 Tower Boot 4 pack - 8810008 Tower Clip Single w/ Rivet - 8810003 Produced 1980 Present Attaches to most rain-gutters or can be custom mounted with Sideloader, Widebody, or Toploader Brackets From Bottom of Tower Boot to bottom of RoundBar is 6.5, Top of Roundbar is 7.75 Pre 1993 Towers came with non-sks lock core, identified by # on lock face, Original version had a round Tower Knob Instructions can be found here Spare Parts
1A HiRise Tower 8000104 1A HiRise Spacer 4 pack - 8001101 Adds 3 inches of height to the 1A Raingutter Tower From Bottom of Tower Boot to bottom of RoundBar is 9.5 From Bottom of Tower Boot to Top of RoundBar is 10.75 Instructions can be found here Spare Parts:
1B Tower No Part Number Produced in 1988 Someone might still own one Spare Parts
1A-TS (Custom Tower) 8001100, 8001102 Produced 1992-1997 The Perfect foundation for custom racks Can be converted to Yakima crossbars at any time Spare Parts
1C - SST TOWER 8000102 TWO PARALLEL LINES DIE CASE ON TOP OF TOWER FOLD DOWN CAM LEVER TWO UNCOVERED RIVETS ON SIDES OF TOWER Produced 1987 1996 Used interchangeable metal Y Clips to attach to car frame Does not work on most cars manufactured after 1997 and none after 2002 Height from bottom of tower to top of crossbar is about 5 1/2 Lockable with SKS locks starting in 1993 The Instructions can be found here There are no Spare Parts Available for the SST Tower besides SKS keys and cores
RailRider 1, 2, 3 8000201, 8000202, 8000203 3 2 1 Produced 1993 1997 A Non-Locking tower Attached to Factory or Yakima Tracks Different versions used different NutPlates Replaced in 1997 with the Locking Railrider Spare Parts:
Q-TOWER 8000105 DIE FORMED IDENTIFICAION STAMP HOLE TO ACCESS WEDGE BOLT REMOVEABLE SIDE PANELS Produced 1993 2004 Uses Metal Q-Clips to attach into a vehicle doorframe Does not work on most cars manufactured after 2004 and none after 2008 Replaced by Q-Tower 8000124 in 2004 Die Form Stamp Smooth
DoubleCross 8000110 3 3/8 LONG T-BOLT OBLONG SHAPED CLAW CAM (BLACK OR RED) Rpl DoubleCross Claw Pad Single - 8710036 SKS COMPATIBLE Produced 1995-2002 Replaced with the LowRider in 2002 Attached to factory side rails Switched from a Claw to a wedge in 1996 Top of Roundbar Usually sits above the racks side rail by about 2 The flat base with a U cut-out was 2.5 long SKS Compatible CAM LIFTS UP FROM THE BOTTOM OF THE TOWER The Doublecross no longer has any spare parts besides SKS keys and cores
WingRider 8000309 (Wing Rider 1), 8000310 (Wing Rider 2) Produced 1997 1999 Packaged with 4 verticle and 8 horizontal Wing MightyMounts for attaching accessories 4 from base to top of Wing bar 5 Wide at base, 3 ½ wide at top Spare Parts
Locking Railrider 8000208 CAM FOLDS DOWN FROM UNDER THE BAR SLIDING BASE Produced from 1997-2002 Replaced Railrider in 1997, Replaced by Control Tower in 2002 Came in three versions for different shaped tracks Instructions: Locking Railrider 1; Locking Railrider 2; Locking RailRider 3 Used Anchor Plates A, B or C depending on the track Replaced by control tower 2003 SKS COMPATIBLE Spare Parts: No Longer Available
CrossTop Tower 8000121 Produced 1998-2001 Designed for the factory side rails of the 98-02 Subaru Forrester Flat base that goes under rail 1.5 (1 shorter than Doublecross) Replaced by the Instructions can be found here
X-Tower 8000109 Produced 2000-2003 A non-locking tower designed for the Nissan Xterra and Frontier Quad Cab Attached to factory side rails Replaced by the LowRider Max in 2006 The Instructions can be found here Spare Parts
LowRider 8000118 SKS COMPATIBLE CLAW OPENS BY LIFTING CAM THEN SPINNING Produced 2001-2009 Attaches to factory raised side rails Replaced the DoubleCross in 2002, replaced by the Railgrab in 2009 The Instructions can be found here Spare Parts: No Longer Available
Control Tower 8000214 SKS COMPATIBLE COVER FOLDS OPEN BY PULLING TABS SYMMETRICAL SLIDING PINS Produced 2002-2016 Attaches to a Landing pad, which connects to fixed points or tracks Could use many different Anchor Plates A, B, C, or D Anchor Plate A for Landing Pad 1 measures 5/8 x 11/16 Replaced the Locking RailRider in 2001, replaced by the Skyline Tower in 2016 SKS Compatible The Instructions can be found here Spare Parts
Forester Tower 8000119 Produced 2003-2006 A non-locking tower designed for the side rails of a 2003-2008 Subaru Forester The Instructions can be found here Spare Parts
Q-TOWER 8000124 Cam Cover Assembly Single - 8810071 PIVOTING SIDE PANELS (Inside on Cam Cover) Q-Lock U Fastener 4 pack - 8810073 Lock Housing and U Fastener Single - 8870026 (Under Cam Cover) Q-Tower Adjustment Post Single - 8810077 Produced 2004 2016 Updated Base pads from Clear to Black in April 2011 Recall on wedges produced from Jan 26 th 2015 to May 26 th 2015 Clips and rubber foot pads are vehicle specific Clips, rubber foot pads, and clip protection pads packaged with Clips SKS Compatible Spare Parts:
EZ Rider 8000130 Produced 2004 2007 Attached to a vehicles factory Flush Side rails Replaced with locking version in 2007 Circular Yakima cap can be removed to expose a 2.25 1/4x20 bolt that used a 5/32 Standard Hex Wrench Spare Parts No Longer Available
LowRider Max 8000136 WEDGE TIGHTENS TOWER TO BAR SKS COMPATIBLE Produced 2006 2009 Designed to fit tall/wide side rails that the lowrider would not fit Replaced by Railgrab in 2009 The Lowrider Max cannot be converted into a Lowrider Had 3 claws designed for different vehicles SKS compatible Spare Parts No Longer Available No Longer Available
Locking EZ Rider 8000137 SKS COMPATIBLE Produced 2006 2009 Replaced the EZ Rider in 2006, replaced by the Railgrab tower in 2010 SKS compatible Spare Parts No Longer Available
RailGrab Tower 8000138 Black Claw Base Bolt 90mm M6 SHCS Wedge Assembly 1 wedge and silver bolt - #8810150 SKS COMPATIBLE Silver bar wedge bolt 35mm M6 SHCS Produced 2009-2016 Attached to Raised or Flush Factory SideRails Used three different claw sizes Small claw- For most factory rail heights less than 1 1/16" (27mm) Medium claw- For most factory rail heights between 1 1/16"-1 3/4" (27-44.5mm) Large claw- For most factory rail heights between 1 3/4"-2 1/2" (44.5-63.5mm) Some Vehicles Require a Railgrab Pin Adapter Kit - #8880201 Tightens with a 5mm hex wrench Spare Parts: 8-32 x.5 w/ cap
Ridgeline 8000145 Ridgeline Rubber Topper Single Pad - #8880625 SKS COMPATIBLE PRESS BOTH 3 DOT CLUSTERS ON EACH SIDE TO TILT OPEN Clip Bolt Single - #8880627 Produced 2016 Present Ridgeclips can be located here Each tower uses 2 clips (1 outboard, 1 inboard) to tighten to a Flush Siderail Bolts tighten to 3.5NM with a 4mm torque wrench (Part #8880613) Replaced Railgrab #8000138 SKS Compatible Works with Jetstream bars, Corebar and Roundbars (Roundbar needs Roundbar SL Adapter #8003536) Ridgeline Instructions can be found here Spare Parts:
Baseline Baseline Rubber Topper Single Pad - #8880619 8000146 Baseline Swing Screw Single - #8880669 PRESS BOTH 3 DOT CLUSTERS ON EACH SIDE TO TILT OPEN SKS COMPATIBLE Produced 2016 Present Uses vehicle specific Baseclips to attach in the door-jam of a naked (bare) roof Replaced Q-Tower #8000124 Bolts tighten to 3.5NM with a 4mm torque wrench (Part #8880613) SKS Compatible Works with Jetstream bars, Corebar and Roundbars (Roundbar needs Roundbar SL Adapter #8003536) Baseline Instructions can be found here Spare Parts:
Timberline Timberline Rubber Topper 8000147 Single Pad - #8880629 SKS COMPATIBLE PRESS BOTH 3 DOT CLUSTERS ON EACH SIDE TO TILT OPEN Rubber Coated Metal Strap Produced 2016 Present Attaches to a raised side rail Replaced Railgrab #8000138 SKS Compatible Bolts tighten to 3.5NM with a 4mm torque wrench (Part #8880613) Works with Jetstream bars, Corebar and Roundbars (Roundbar needs Roundbar SL Adapter #8003536) Timberline Instructions can be found here Spare Parts:
Skyline Rubber Topper Single Pad - #8880629 Skyline 8000148 SKS COMPATIBLE PRESS BOTH 3 DOT CLUSTERS ON EACH SIDE TO TILT OPEN SYMMETRICAL SLIDING PINS Produced 2016 Present Compatible with Landing Pads Bolts tighten to 3.5NM with a 4mm torque wrench (Part #8880613) Replaced the Control Tower SKS Compatible The Symmetrical sliding pins are not a replacement part Works with Jetstream bars, Corebar and Roundbars (Roundbar needs Roundbar SL Adapter #8003536) The Skyline Tower Instructions can be found here Spare Parts: