SERVICE MANUAL (SRKF shown) Battery-powered Pistol Grip T/X Tools Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. 0000 0 Sherman + Reilly, Inc. /
Battery-powered Pistol Grip T/X Tools Table of Contents Safety... Purpose of this Manual... Other Publications... Important Safety Information... Main Illustration All Tools... Main Parts List All Tools... Motor Illustration and Parts List All Tools... Release Lever Illustration and Parts List All Tools... Pump Illustration and Parts List SRKF, SRG, SRKAF, SRKA, SRS... SRKI, SRK, SRKK, SRK, SRKC SRKF, SRG, SRG, SRS... Relief Valve Illustration and Parts List All Tools... Piston Pump Illustration and Parts List All Tools... Head and Ram Illustration and Parts List SRKA... 0 SRKAF... SRKF... SRKP... - SRK, SRKC... SRKI... Indenter and Head Replacement... SRKK... SRK... 0 SRKF... SRG... SRG... SRG... SRS... SRS... Safety Safety is essential in the use and maintenance of Sherman + Reilly tools and equipment. This manual and any markings on the tool provide information for avoiding hazards and unsafe practices related to the use of this tool. Observe all of the safety information provided. Purpose of this Manual This manual is intended to familiarize authorized Sherman + Reilly service personnel with the service parts for the Sherman + Reilly Battery-powered Pistol Grip Tools listed on this page. Keep this manual available to all personnel. Replacement manuals are available upon request at no charge at www.sherman-reilly.com. Other Publications Operation Manuals SRG T/X 000 SRG T/X 000 SRG T/X 000 SRKA T/X 0 SRKAF T/X 0 SRKF T/X 000 SRKC T/X 000 SRKI T/X 000 SRK T/X 000 SRKK T/X 000 SRK T/X 000 SRKF T/X 000 SRKP T/X 0 SRS T/X 000 SRS T/X 000 Do not discard this product or throw away! For recycling information, go to www.sherman-reilly.com. KEEP THIS MANUAL All specifications are nominal and may change as design improvements occur. Sherman + Reilly shall not be liable for damages resulting from misapplication or misuse of its products.
Battery-powered Pistol Grip T/X Tools IMPORTANT SAFETY INFORMATION SAFETY ALERT SYMBOL This symbol is used to call your attention to hazards or unsafe practices which could result in an injury or property damage. The signal word, defined below, indicates the severity of the hazard. The message after the signal word provides information for preventing or avoiding the hazard. Skin injection hazard: Do not use hands to check for oil leaks. Oil under pressure easily punctures skin. If injured, seek medical attention immediately to remove oil. Failure to observe this warning could result in serious injury, gangrene, or death. Immediate hazards which, if not avoided, WILL result in severe injury or death. Hazards which, if not avoided, COULD result in severe injury or death. Do not use solvents or flammable liquids to clean the tool body. Solvents or flammable liquids could ignite and cause serious injury or property damage. Hazards or unsafe practices which, if not avoided, MAY result in injury or property damage. Do not dispose of batteries in a fire. They will vent fumes and may explode. Failure to observe this warning could result in severe injury from harmful fumes or burns from flying debris. Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Refer also to the Operation Manual, which is listed under Other Publications. Failure to observe this warning could result in severe injury or death. Do not perform any service or maintenance other than as described in this manual. Injury or damage to the tool may result. Failure to observe this precaution may result in injury and property damage. Wear eye protection when operating or servicing this tool. Failure to wear eye protection could result in serious eye injury from flying debris or hydraulic oil. Note: Keep all decals clean and legible, and replace when necessary.
Battery-powered Pistol Grip T/X Tools Main Illustration All Tools 0 T=. Nm max. F A E T=0 Nm B T= Nm max. T= Nm T=. Nm T=0 Nm D
Battery-powered Pistol Grip T/X Tools Main Parts List All Tools 00 Housing unit, -ton... 00 Housing unit, -ton... A Left housing... B Right housing... D Retract button... E Spring... F Screw... 0 Motor gearbox unit... 0 Release lever unit... 000 Pump housing unit (SRKF)... 00 Pump housing unit (SRKA, SRKAF)... 00 Pump housing unit (-ton crimper)... 00 Pump housing unit (-ton crimper)... 00 Pump housing unit (SRS, SRG)... 000 Pump housing unit (SRS, SRG)... 00 Pump housing unit (SRG) 0 Relief valve unit (all except SRS,... SRG)... 00 Relief valve unit (SRS, SRG)... 0 Piston pump unit... 00 Sensor (CRIMPERS)... 0 Screw (ECCXL, ECCXL, CUTTERS)... Seal (included in 00 seal kit)... 00 Circuit board (T version)... 000 Circuit board (X version)... 0 Decal, -ton, brand... 0 Decal, -ton, brand... 0 0 Identification decal (SRKAT)... 0 Identification decal (SRKAX)... 00 Identification decal (SRKAFT)... 0 Identification decal (SRKAFX)... 0 Identification decal (SRKFT)... 0 Identification decal (SRKFX)... 0 Identification decal (SRKT)... 00 Identification decal (SRKX)... 0 Identification decal (SRKCT)... 0 Identification decal (SRKCX)... 0 Identification decal (SRKIT)... 00 Identification decal (SRKIX)... 0 Identification decal (SRKKT)... 0 Identification decal (SRKKX)... 0 Identification decal (SRKT)... 0 Identification decal (SRKX)... 0 Identification decal (SRKFT)... 0 Identification decal (SRKFX)... 0 Identification decal (SRGT)... 00 Identification decal (SRGX)... 0 Identification decal (SRGT)... 0 Identification decal (SRGX)... 0 Identification decal (SRGT)... 0 Identification decal (SRGX)... 0 Identification decal (SRST)... 0 Identification decal (SRSX)... 0 Identification decal (SRST)... 0 Identification decal (SRSX)... 0 Identification decal (SRKPT)... 0 Identification decal (SRKPX)... 000 Decal, FCC, T version 000 Decal, FCC, X version 0 Trigger 00 Ring 0000 Pin 00 Ring, hang 000 Carrying case (SRKF) 0 Carrying case (All Others) 000 Carrying case (SRG, SRS) 00 Connector compatibility decal (SRKP) 00 Connector compatibility decal (SRKF) 00 Connector compatibility decal ( & Ton Tools) 00 Connector compatibility decal (SRKA) 0 Connector compatibility decal(srkaf) 00 Connector chart decal (SRKI) 00 Seal kit 00 0 VAC corded adapter 00 0 VAC corded adapter 0 V, Ah lithium-ion battery 00 0 VAC, V charger 00 0 VAC, V charger 00 VDC, V charger 0 Li ( V) to NiCd, NiMH ( V) charger adapter 0 Carrying strap 0 Biodegradable hydraulic fluid ( qt)
Battery-powered Pistol Grip T/X Tools Motor Illustration and Parts List All Tools T= Nm T= 0 Nm 0 Motor gearbox unit 00 Motor and pinion... Gearbox with eccentric... Retaining ring... Grooved ball bearing... Screw... Eccentric case... Flange... Screw... 0 Gear box screw... Release Lever Illustration and Parts List All Tools T=. Nm 0 Release lever unit Release lever... Socket head screw... Compression spring...
Pump Illustration and Parts List SRKA, SRKAF, SRKF, SRS, SRG Battery-powered Pistol Grip T/X Tools T= Nm T= Nm Screw in valve body until disc springs are flat. A, B T=0. Nm 0 T= Nm C T=. Nm 00 Pump housing unit (A) (SRS, SRG) 000 Pump housing unit (B) (SRKF) 00 Pump housing unit (C) (SRKA, SRKAF) Reservoir plug... 00 Reservoir... Cable tie (included in 00)... 000 Threaded bushing... A Pump housing... B Pump housing... 00 Threaded bushing... Filter... Bearing... Switch lever... 0 Screw... Bearing... O-ring (included in 00)... Pin... Screw... Needle valve... O-ring... Compression spring... Disc spring... Solenoid... Cable tie (included in 00)... 000 Solenoid kit, cutters [includes, (), ] 00 Solenoid kit, crimpers (includes ) 00 Switch lever kit (includes 0) 00 Wrench, bushing
Battery-powered Pistol Grip T/X Tools Pump Illustration and Parts List SRKI, SRK, SRKC, SRKK, SRK, SRKF, SRG, SRG, SRS T= Nm T= Nm 0 Screwed down until disc spring is flat. 0 T= Nm T=0. Nm T=. Nm 00 Pump housing unit (-TON CRIMPER) 00 Pump housing unit (-TON CRIMPER) 000 Pump housing unit (SRG, SRS) 00 Pump housing unit (SRG) Reservoir plug... Cable tie (included in 00)... 00 Reservoir... Cable tie (included in 00)... 000 Threaded bushing... Pump housing... Hanging ring... 00 Threaded bushing... Filter... 0 Bearing... Switch lever... Screw... Bearing... O-ring (included in 00)... Pin... Screw... Needle valve... O-ring... Compression spring... 0 Disc spring... Solenoid... 000 Solenoid kit, cutters [includes -, 0 (), ] 00 Solenoid kit, crimpers (includes -) 00 Switch lever kit (includes 0 ) 00 Wrench, bushing
Relief Valve Illustration and Parts List All Tools Battery-powered Pistol Grip T/X Tools 0 Relief valve unit (all except SRS, SRG) 0 Relief valve unit (SRG, SRS) Seal (included in 00)... 000 Valve seat (all except SRS, SRG)... 0 Valve seat (SRS, SRG)... Needle valve... Plunger... Washer... Compression spring... O-ring (included in 00)... Pressure relief valve... O-ring (included in 00)... 0 Screw... 0 Piston Pump Illustration and Parts List All Tools 0 Piston pump unit Pump piston... Screw plug... Piston seal (included in 00)... Washer (included in 00)... Pump piston... Valve stem... Spring...
Battery-powered Pistol Grip T/X Tools Head and Ram Illustration and Parts List SRKA 0 0 00 Quad point head assembly (includes ) 00 Cam yoke assembly... Roller bearings... Bearing retainers... 0000 Compression spring... 0000 Screw... 000 Fixed jaw... 000 Moving jaw... 000 Pivot roller... 000 Pivot pin... 0 000 Screw... 000 Head kit (includes, ) Head cover (LH)... Head cover (RH)... 00 Spring pin... 00 Spring pin... 0 O-ring (included in 00)... Backup ring (included in 00)... 00 Piston... 000 Pin... 00 Compression spring... 000 Sleeve... 00 Bearing retainer kit (includes, ) 0
Battery-powered Pistol Grip T/X Tools Head and Ram Illustration and Parts List SRKAF 0 0 0 00 Quad point flip-top head assembly (includes ) 00 Cam yoke assembly... 00 Latch (includes )... 00 Moving jaw... Roller bearing... Bearing retainer... 00 Latch mounting pin... Latch nib (included in 00)... 000 Lock pin... 000 Side jaw roller... 0 0000 Compression spring... 000 Ball screw... 00 Snap ring... 0000 Screw... 000 Screw... 00 Set screw... 00 Spring pin... 0 Head cover... 0 O-ring (included in 00)... Backup ring (included in 00)... 00 Piston... 000 Pin... 00 Compression spring... 000 Sleeve... 00 Bearing retainer kit (includes, )
Head and Ram Illustration and Parts List SRKF Battery-powered Pistol Grip T/X Tools T= Nm 0 0 T= Nm 0 Head assembly (includes ) 0 Ram... 00 Adapter disk... * O-ring (included in 00)... 00 Compression spring... 0 Pin kit (includes, ) Spring... Pin... Pin... 0 Die retainer kit (includes 0,, ) 0 Die retainer... Compression spring... 00 Screw... 000 Bottom crimp head... 0 Latch... 0 Top die holder... 0 Bottom die holder... Retaining ring... Die release button... Die retainer... 0 Roll Pin... Die release button... Locking pin... 0 Die holder kit (includes, ) Threaded stud... Pin... 00 Piston cup... * Backup ring (included in 00)... * O-ring (included in 00)...
Battery-powered Pistol Grip T/X Tools Ram Illustration and Parts List SRKP T= Nm 0 0000 Ram unit (includes )... 00 Sheath... 0 Spring kit (includes ) Shoulder bolt... Disc... Compression spring... Washer... * O-ring (included in 00)... 0 Screw... Jaw holder... 000 Latch kit (includes ) Compression spring... 0 Locking pin... Compression spring... Pin... 00 Roller kit (includes, ) Roller... Ram... 0000 Bushing with seal... * Seal bushing (included in 00)...
Battery-powered Pistol Grip T/X Tools Jaw Units Illustration and Parts List 0 CJ CJXPJ C B 0 CJB A 0 CJ crimping jaw unit for cul and UL classified crimps 0 CJXPJ crimping jaw unit (includes -) 0 CJB single-use lock cutter (includes -) 00 Jaw pivot kit (includes, ) Retaining ring... Pivot pin... A Jaw, sharp CJB... B Jaw, CJXPJ... C Jaw, CJ... 0 Extension spring... Jaw, flat CJB... 0 Die retaining pin kit (includes 0) Die retaining pin... Compression spring... Release button... 0 Retaining ring...
Jaw Units Illustration and Parts List (cont d) Battery-powered Pistol Grip T/X Tools CJDBG CJDO CJD A A C 0A 0C 0D A A C 0 glued in with Loctite 0 (green) B 0 CJK Kearney 0B B 0 CJDBG crimping jaw unit (includes 0 ) 0 CJDO crimping jaw unit (includes 0 ) 00 CJD crimping jaw unit (includes 0 ) 00 CJK Kearney crimping jaw unit (includes 0, -) 0A Jaw, CJDBG... 0B Jaw, CJK... 0C Jaw, CJDO... 0D Jaw, CJD... 0 Extension spring... 00 Jaw pivot kit (includes, ) Retaining ring... Pin pivot... Bushing... Compression spring... Lock adapter... A 0 Jaw covers, CJDO/CJDBG (set of )... B 0 Jaw covers, CJK (set of )... C 00 Jaw covers, CJD (set of )... Bushing... 0 Ball, mm... Locking pin... 000 Die pin kit, W -style dies (includes ) 000 Die pin kit, Kearney-style dies (includes, )
Battery-powered Pistol Grip T/X Tools Head and Ram Illustration and Parts List SRK, SRKC 0 0 00 C-head assembly, mm (includes ) 00 C-head assembly, mm PVC-Covered (includes ) C-head, mm... 00 Compression spring... 00 Groove pin... 00 Die release button... 00 Die release pin... Set screw, M-0. x mm skt cup pt... 00 Ram assembly (includes items ) 00 Compression spring... 00 Die release pin... 0 00 Release shaft... 00 Spring pin... Ram... 000 Spring kit (includes -) Stop... Disc... Spring stop... Screw, M-0. x 0 mm skt head cap... Screw, M-.0 x 0 mm skt head cap... O-ring (included in 00)... Ram spring... 0 O-ring (included in 00)... Backup ring (included in 00)... 00 Piston...
Head and Ram Illustration and Parts List SRKI Battery-powered Pistol Grip T/X Tools 0 0 00 Head and ram unit (includes, ) 00 Yoke... O-ring (included in 00)... 000 Ram... 00 Spacer,.00 x. x...(as needed) 000 Spacer,.0 x. x...(as needed) 00 Indenter... 0 Retaining ring... 00 Pivot pin... Screw, #0- x. skt set cone pt... 0 0 Crimp head... 00 Latch... 00 Torsion spring... Spring... Screw, M-.0 x 0 mm skt head cap... End cap... Screw, M-0. x 0 mm skt head cap... Stop... 0 O-ring (included in 00)... Backup ring (included in 00)... 00 Piston... 00 Spring kit (includes, )
Battery-powered Pistol Grip T/X Tools Indenter and Head Replacement SRKI This procedure is separated into two sections, one for the indenter and one for the head. Indenter. Lift the latch and open the crimping head.. Remove set screw (), indenter (), and any spacers ( and ).. Lubricate indenter tangs that slide against the yoke. Reinstall spacers ( and ) and indenter ().. Close crimping head and check that latch and head are fully engaged.. Reinstall the battery and advance the indenter to full stoke. Release trigger when the sound of motor speed begins to slow down.. Measure the distance between the bottom of the indenter and head as shown below. The distance should measure. mm to.0 mm (0." to 0.0"). If the dimension is outside this range, remove set screw () and indenter (). to increase distance, remove a spacer (, ). to decrease distance, add a spacer (, ). Head. Lift the latch and open the crimping head.. Remove the retaining ring (), pin (), head (0), and spring ().. Install spring () with long end into the yoke hole. Reinstall head (0), pin (), and retaining ring ().. Close crimping head and check that latch and head are fully engaged.. Reinstall the battery and advance the indenter to full stoke. Release trigger when the sound of motor speed begins to slow down.. Measure the distance between the bottom of the indenter and head as shown below. The distance should measure. mm to.0 mm (0." to 0.0"). If the dimension is outside this range, remove set screw () and indenter (). to increase distance, remove a spacer (, ). to decrease distance, add a spacer (, )..0..0.. Install indenter () and secure with set screw ().. Install indenter () and secure with set screw ().
Head and Ram Illustration and Parts List SRKK Battery-powered Pistol Grip T/X Tools 0 00 C-head assembly, Kearney (includes ) 00 C-head assembly (includes ) C-head... 00 Set screw... 0 Ball detent... 00 Set screw... 0 Ball detent... 00 Ram... 000 Spring kit (includes ) Stop spring... Disc... Stop... 0 Screw, M-0. x 0 mm skt head cap... Screw, M-.0 x 0 mm skt head cap... O-ring (included in 00)... Ram spring... O-ring (included in 00)... Backup ring (included in 00)... 00 Piston...
Head and Ram Illustration and Parts List SRK Battery-powered Pistol Grip T/X Tools 0 0 Head unit (includes ) Crimp head... Ram... Piston guide... 0 Ball plunger... 00 Die retainer kit (includes ) Disk... Spring... Die pin... Nut... 00 Handle... 0 Spring... Screw, M-.0 x 0 mm skt head cap... 0000 End cap... 00 Piston... Backup ring (included in 00)... O-ring (included in 00)... 00 Screw... 0 Stop... 0
Head and Ram Illustration and Parts List SRKF Battery-powered Pistol Grip T/X Tools 0 0 0 Head assembly (includes ) Crimping head base... Head, movable... Die retaining pin... Compression spring... Die releasing button... Ram... Pin... Retaining ring... Pull pin... 0 Compression spring... Lock pin... Compression spring... O-ring... Washer... Spring... End cap... Screw, M x 0 mm socket head cap... 00 Stop... Screw, M x 0 mm socket head cap... 0 O-ring (included in 00)... Backup ring (included in 00)... 00 Piston cup... 00 Handle... 00 Die pin kit (includes two each of ) 0 Pivot pin kit (includes ) 0 Seal kit (includes, 0, ) 0 Ram kit (includes, )
Head and Ram Illustration and Parts List SRG Battery-powered Pistol Grip T/X Tools 0 00 Head unit (includes 0) 00 Cutting head... 00 Cutting blade... 00 Pin... 00 Spring... 00 Screw... 000 Cutting head base... 00 Adapter disk... O-ring (included in 00)... 00 Latch... 0 000 Retaining ring... O-ring (included in 00)... Piston backup ring (included in 00)... 00 Compression spring... 00 Piston... 00 Pin...
Head and Ram Illustration and Parts List SRG Battery-powered Pistol Grip T/X Tools 0 0 00 Head and ram unit (includes ) 00 Spring bolt... 0000 End cap... Spring... Spring guide... Adapter disk... O-ring (included in 00)... Screw... Stop... Cutting head base... 0 Handle block... Compression spring... Ball pin indent... Pin assembly... Pin guide... Frame plate... Screw... Spacer... Retaining ring... 0 Pin... Blade holder... Pin... 0 Cutting blade... Screw... 0 Cutting head... Blade guide... O-ring (included in 00)... Backup ring (included in 00)... 00 Piston... 00 Fastener kit (includes,,,,,,.. 0,, )... 0 Plate kit (includes, 0,,,, )... 0 Spring kit (includes -, )...
Battery-powered Pistol Grip T/X Tools Head and Ram Illustration and Parts List SRG 0 0 0 Cutting head (includes ) 0 Movable cutting blade... 0 Pin... 0 Fixed cutting blade... Cutting head base... Handle block... Frame plate... Spacer... Pin guide... Blade guide... 0 Socket head cap screw... End cap... Spring, 0 mm... Cylinder sleeve... Blade holder... Screw... Pin... Retaining ring... Screw... Compression spring... 0 Ball pin detent... Pin assembly... Fillister head screw... Stop... O-ring... Backup ring (included in 00)... 00 Piston 0 Plate kit (includes ) 00 Spring kit (includes 0 ) 0 Fastener kit (includes, )
Head and Ram Illustration and Parts List SRS Battery-powered Pistol Grip T/X Tools 0 0 0 Cutting head (includes ) Shrink cover... M x mm socket head cap screw... 00 Piston rod... 00 Return spring... 0 Spring cup... Bearing block... 0 Blade... 00 Clevis pin... 00 Blade guide... 0 00 M socket head cap screw... Link... Pin... Retaining ring... 00 M hex nut... Screw... Yoke... 00 Stop... 00 Handle... 00 Piston... 0 Piston backup ring (included in 00)... O-ring (included in 00)... 0 Pin kit (includes,)
Head and Ram Illustration and Parts List SRS Battery-powered Pistol Grip T/X Tools 0 0 0 Cutting head (includes ) Screw... Piston rod... Spring... Cylinder sleeve... Cutter body... Tubing... 00 Socket head cap screw... Socket head cap screw... Cutter blade... 0 Blade guide... Pivot pin... Attachment block... Hex nut... Retaining ring... Pin... Double fork... 00 Handle... O-ring (included in 00)... Backup ring (included in 00)... 0 00 Piston... 0 Stop... 0 Blade kit (includes 0) 0 Pin kit (includes, ) 0 Attachment block kit (includes, )
Phone 00--0 --00 Fax -- www.sherman-reilly.com