MATERIALS INCLUDED e TOOLS NEEDED 5/16" hex it or tmper-resistnt srews penil rthet steel wire rush loking pin epoxy 1/4", 1/2" & 7/8" rill its or onrete hmmer rill epoxy gun Bse plte top view- noth etil Test it tle olumn with se plte Align tle olumn to se plte mounting holes eore mounting se plte; the olt pttern is not squre. Mrk hole lotions Ple the sunshe se plte in esire lotion. Mrk enter o eh hole lotion with penil. Mounting holes re lote on the sunshe s se plte. To show multiple Soleris Sunshes in the sme orienttion, lign the noth on the se pltes (etil ove) in the sme iretion. Drill holes Use hmmer rill to rill 5 eep x 7/8 imeter nhor holes t eh mrke lotion using 7/8 rill it suitle or onrete rilling. NOTE: Forms+Sures reommens strting holes with 1/4 imeter rill it ollowe y 1/2 n inlly 7/8 or mximum ury. 2014 Forms+Sures All imensions re nominl. Speiitions n priing sujet to hnge without notie. For the most urrent version o this oument, plese reer to our wesite t www.orms-sures.om. pge 1 o 5 10-27-14
Fill holes & insert nhors Use ompresse ir n steel wire rush to len eh nhor hole in orne with epoxy instrutions. Use epoxy in epoxy gun to ill eh nhor hole 5/8 o the hole epth in orne with epoxy instrutions. Insert 1/2-13 x 5 epoxy nhor () into eh nhor hole so nhor top is lush with groun. Allow proper uring time oring to ure sheule on epoxy instrutions eore moving on to the next step. Position seplte Position seplte so tht mounting holes line up with nhors. Atth seplte Slie 1/2 stinless steel lok wsher (), n 1/2 stinless steel lt wsher (), onto eh 1/2-13 x 1.5 tmperresistnt utton he p srew (). Insert srews into mounting holes in the sunshe s se plte n thre into nhors using provie 5/16 hex it or tmper-resistnt srews. 2014 Forms+Sures All imensions re nominl. Speiitions n priing sujet to hnge without notie. For the most urrent version o this oument, plese reer to our wesite t www.orms-sures.om. pge 2 o 5 10-27-14
7 8 9 Tighten srews Tighten srews until snug. Atth tle olumn to se plte Slie 1/2 stinless steel lok wsher (), n 1/2 stinless steel lt wsher (), onto eh 1/2-13 x 1.25 tmperresistnt utton he p srew (). Insert srews into mounting holes in the tle olumn n thre into nhors using provie 5/16 hex it or tmperresistnt srews. Atth tle top to tle olumn Use 7/32" Allen wrenh to tth tle top to tle olumn using our (4) 3/8" -16 x 1" utton he p srews (e). NOTE: Tle top must e supporte uring this step. 2014 Forms+Sures All imensions re nominl. Speiitions n priing sujet to hnge without notie. For the most urrent version o this oument, plese reer to our wesite t www.orms-sures.om. pge 3 o 5 10-27-14
10 11 12 Put sunshe pole into the mounting pole Ple sunshe pole, with noth ing up, through the tle into the mounting pole. Insert loking pin to ix mounting pole to mounting ssemly Line up the pre-rille holes in the mounting pole n mounting pole sleeve, n insert the loking pin. Slie sunshe ssemly onto sunshe pole Slie the tue in the enter o the sunshe ssemly onto the sunshe pole, linking the two piees together. 2014 Forms+Sures All imensions re nominl. Speiitions n priing sujet to hnge without notie. For the most urrent version o this oument, plese reer to our wesite t www.orms-sures.om. pge 4 o 5 10-27-14
13 14 Rotte sunshe Rotte sunshe until it engges with pins. Tighten srew on top o sunshe Tighten srew on top o sunshe with rthet until snug. 2014 Forms+Sures All imensions re nominl. Speiitions n priing sujet to hnge without notie. For the most urrent version o this oument, plese reer to our wesite t www.orms-sures.om. pge 5 o 5 10-27-14