APPLICATION HIGH PRESSURE FILTERS For Manifold Block Mounting Series DF...P Pressures to 45 psi Flows to 18 gpm HYDAC DF...P High Pressure Filters are designed to be mounted directly onto the manifold block to save space and reduce leak points and mounting hardware. These filters can be installed on the high-pressure side of the pump to protect control valves and actuators from contamination. PRODUCT FEATURES Models DF 6-24 P have a steel filter head and screw-in bowl made of cold-formed steel. The DF 33 P and DF 66 P have a filter head of ductile iron and a screw-in bowl of cold-formed steel. The filter housings are designed to withstand pressure surges as well as high static pressure loads. The screw-in bowl allows the filter element to be easily removed for replacement or cleaning. A visual (pop-up), electrical, electrical/visual (lamp), or electronic differential type clogging indicator can be installed. DF...P filters are available with or without a bypass valve so either high or low collapse pressure elements may be used. Multiple indicator port locations (DF33/66P only) also allow two different types of indicators to be installed into the filter. Indicators of the same type, but with different trip pressures can also be installed. FILTER ELEMENTS DF...P Manifold Mounting Filters DF...P Filters are available with disposable Betamicron Low Collapse (BN3HC) elements having 25 psid and Betamicron High Collapse (BH3HC) having 3 psid collapse pressure and absolute ratings of 3, 5, 1, and 2 micron. DF...P Filters are also available with cleanable elements. Metal Fiber (V) stainless steel fiber elements have a 3 psid collapse pressure and nominal ratings of 3, 5, 1, and 2 micron. Wire screen (W/HC) elements have a 25 psid collapse pressure and nominal ratings of 25, 74, and 149 micron. For nonbypass applications, Betamicron (BH3HC) or metal fiber (V) elements must be installed. If a bypass valve is used, Betamicron (BN3HC) or wire screen (W/HC) elements can be installed. All filter media is supported to achieve flow fatigue resistance. Proper support of the filter media also provides high Beta Ratio values (particle removal efficiency) even at high differential pressures. The efficiency of many competitive elements drastically deteriorates as the element clogs and differential pressure increases. High quality epoxy adhesive is used to bond the end caps to the media and to bond the seam of the media.
Filter Type DF = 45 psi (315 bar) Filter Media BH3HC = Betamicron BH3HC High Collapse BN3HC = Betamicron BN3HC Low Collapse (Disposable) V = Metal Fiber W/HC = Wire Screen (Cleanable) Size and Nominal Port Size 6 = 3/4" 11 = 3/4" 16 = 1" 24 = 1" 28 = 1" 33 = 1 1/4" 66 = 1 1/4" Type of Connection P = Manifold Block Mounting - Top of Filter Head Filtration Rating (micron) 3 5 Betamicron 1 (BH3HC or BN3HC) Absolute Filtration Rating (ßx ³ 2) 2 DF BH3HC 6 P 3 A 1. / 3 5 Metal Fiber 1 (V) 2 Nominal Filtration Rating 25 Wire Screen 74 (W/HC) 149 Type of Differential Pressure Clogging Indicator A = no clogging indicator DF B = visual (pop-up) clogging indicator (automatic reset) VD5B.1 BM = visual (pop-up) clogging indicator (manual reset) VD5BM.1 C = electrical clogging indicator (electric switch) VD5C. D = electrical/visual (lamp) clogging indicator (electric switch & light) VD5D./L... J = electric switch (Brad Harrison, 5 pin mini) VDH5J. J4 = electric switch (Brad Harrison, 4 pin micro) VDH5J4. Type Number 1 = Standard Connection Modification Number = Sizes 6-28 1 = Sizes 33 & 66 Seals (omit) = Nitrile (NBR) (standard) V = Fluoro Rubber (FKM) EPR = Ethylene Propylene (EPDM) Bypass Valve (omit) = Without Bypass (BH3HC or V elements recommended) B3 = 43 psid Bypass (optional) B6 = 87 psid Bypass (standard) Supplementary Details SO13H = Modification of BN3HC (Low Collapse) & W/HC Element For Phosphate Ester Fluids SO155H = Modification of BH3HC (High Collapse) Element For Phosphate Ester Fluids SO184 = G-1/2 Drain in Bowl Option For Sizes 6-28 (standard for sizes 33 & 66) SO11 Model Code: Filter Assembly DF...P = Indicator with brass piston (for water based fluids) L24 = Lamp for 24 Volts T7 - Indicator Thermal Lockout, 7 F L48 = Lamp for 48 Volts (D-type clogging T1 - Indicator Thermal Lockout, 1 F L115 = Lamp for 115 Volts indicator only) L23 = Lamp for 23 Volts Model Codes Containing Red are non-stock items Contact HYDAC for availability (Consult factory on B & BM Indicators for thermal lockout) 2
Element Size Housing Size 6 = DF 16 P 11 = DF 11 P 16 = DF 16 P 24 = DF 24 P 28 = DF 28 P 33 = DF 33 P 66 = DF 66 P High Pressure Element Model Code: High Pressure Filter Elements 6 D 3 BH3HC Filtration Rating (micron) 3 = 3 µm 5 = 5 µm Betamicron Absolute Filtration Rating (ßx ³ 2) 1 = 1 µm (BH3HC or BN3HC) 2 = 2 µm 3 = 3 µm 5 = 5 µm Metal Fiber 1 = 1 µm (V) 2 = 2 µm Nominal Filtration Rating 25 = 25 µm Wire Screen 74 = 74 µm (W/HC) 149 = 149 µm Filter Element Material BH3HC = Betamicron BH3HC High Collapse BN3HC = Betamicron BN3HC Low Collapse V = Metal Fiber W/HC = Wire Screen (Disposable) (Cleanable) Seals (omit) = Nitrile (NBR) (standard) V = Fluoro Rubber (FKM) EPR = Ethylene Propylene (EPDM) Supplementary Details SO13H = Modification of BN3HC & W/HC Elements for Phosphate Ester Fluids SO155H = Modification of BH3HC Element for Phosphate Ester Fluids Model Codes Containing Red are non-stock items Contact HYDAC for availability 3
Engineering Data: DF...P Design: Pressure Filter for Manifold Mounting Mounting Method: 4 Mounting holes in filter head (DF 6-28 P) 6 mounting holes in filter head (DF 33-66 P) Connections: Manifold Mount Direction of Flow: Inlet: Top Outlet: Top Housing Pressure Ratings: Operating: 45 psid (315 bar) Proof: 6 psid (414 bar) Fatigue: Contact HYDAC office Burst: Contact HYDAC office Element Collapse Standard Elements: BN3HC: 25 psid (17 bar) Pressure Ratings: W/HC: 25 psid (17 bar) (ISO 2941) High Collapse Elements: BH3HC: 3 psid (27 bar) V: 3 psid (27 bar) Fluid Temperature Range: Fluid Compatibility: (ISO 2948) Flow Fatigue Resistance: (ISO 3724) Trip Pressure of Differential Pressure Indicator: Cracking Pressure of Bypass Valve: Hydraulic Symbol: -15 F to +25 F (-26 C to 121 C) Based on Nitrile Seals under maximum continuous operating pressure. Please contact HYDAC for information on extreme low temperature applications (below -15 F.) Compatible with all petroleum oils, water glycols, oil/water emulsions, high water base fluids, and synthetic fluids compatible with Fluoro Rubber or EPR seals. Filter medium is supported to achieve flow fatigue resistance. Contact HYDAC office for information. DP = 72 psid (5 bar) - 1%(Standard) Optional trip pressures available, contact HYDAC office for information. DP = 87 psid (6 bar) + 1% (Standard) Optional trip pressures available, contact HYDAC office for information. INLET DF...P Bypass Valve Filter Element Pop-up Indicator Weights: Model With Element Without Element lbs. kg. lbs. kg. DF 6 P 11. 5. 1.6 4.8 DF 11 P 13. 5.9 12.3 5.6 DF 16 P 19.2 8.7 18.1 8.2 DF 24 P 22.7 1.3 21.2 9.6 DF 28 P 35. 15.9 31. 14.1 DF 33 P 5.2 22.8 48.1 21.8 DF 66 P 68.2 31. 63.4 28.8 Filtration Efficiency: Multi-Pass Filtration Efficiency Ratings to ISO 4572 for Betamicron Elements OUTLET For all micron ratings (3, 5, 1, & 2), both High and Low Collapse Betamicron Elements Absolute Filtration Rating = ßx ³ 2 Terminal ÆP Across Element = 72 psid (5 bar) Above subject to Technical Modifications. 4
Filter Sizing Calculations: Assembly: To calculate the pressure drop of the filter assembly use the equation: ÆP Assembly = ÆP Housing + ÆP Element Housing: The housing curve is based on test results using mineral oil with a specific gravity of.86. Differential pressure increases in proportion to specific gravity of applicable fluid. To adjust the housing ÆP for the fluid being used, use the equation: ÆP Housing = ÆP Curve x Actual Specific Gravity.86 DF 6/11 P Housing DF 16/24/28 P Housing DF 33/66 P Housing 2. 3 4. 6 2. 3 1.5 2 3. 4 1.5 2 ÆP in bar 1..5 1 ÆP in bar 2. 1. 2 ÆP in bar 1..5 1 5 1 15 2 25 3 1 2 3 4 5 6 5 1 15 2 2 4 6 8 1 12 Q in l/min 4 8 12 16 2 24 Q in l/min 12 24 36 48 6 72 Q in l/min Bypass Valves Curve: Curves shown are applicable for mineral oil with a specific gravity of.86. Differential pressure increases in proportion to the specific gravity of the fluid. To adjust the bypass ÆP for the fluid being used, use the equation: ÆP Valve = ÆP Curve x Actual Specific Gravity.86 12 1 8 6 4 2 DF 6/11 P 2 DF 16-28 P 16 12 DF 33/66 P 8 4 1 2 3 4 5 6 7 8 9 1 5 1 15 2 25 3 35 4 5
Element ÆP Calculations: All element curves are based on test results using mineral oil with a kinematic viscosity of 141 SUS and a specific gravity of.86. The differential pressure across the element changes proportionally to the viscosity and specific gravity. ÆP Element = ÆP Curve x Actual Specific Gravity Actual Viscosity x.86 141 Wire Screen Elements: To find ÆP across clean wire screen element divide application flow by maximum recommended flow and find percentage; then read ÆP from graph. Application Flow Max. Recommended Flow Example: 25 Wire Mesh, 1 gpm, Size 6 x 1 = % of Flow Model Max. Recommended Flow (gpm) DF 6 P 16 DF 11 P 29 DF 16 P 42 DF 24 P 63 DF 28 P 63 DF 33 P 87 DF 66 P 174 1 gpm = 63% of Flow 16 gpm 63% of flow = 1 psi ÆP for 6D25W element ÆP in bar 2. 1.5 1..5 3 2 1 D...W/HC % 2% 4% 6% 8% 1% 12% as % of max. recommended flow Betamicron 3 Plus & Metal Fiber Elements: To find ÆP across clean Betamicron & Metal Fiber elements, use the equation below with the K Factors from the charts ÆP Element = K Factor x Flow (gpm) x Act. Spec. Gravity Act. Viscosity x.86 141 Betamicron Low Collapse K Factors for...d...bn3hc Elements Size 3µm 5µm 1µm 2µm 6 2.25184 1.5123 1.6344.63445 11 1.26133.7341.593.33433 16.8327.4682.36675.22615 24.4856.34364.1984.12695 28.24889.15763.11511.6992 33.3497.25519.15847.8921 66.16517.12362.7676.4321 Betamicron High Collapse K Factors for...d...bh3hc Elements Size 3µm 5µm 1µm 2µm 6 3.1556 1.73264 1.25471.6526 11 1.8544.9398.66311.33196 16 1.1859.62163.6323.32134 24.61757.39648.33622.18932 28.36155.1919.17375.7937 33.5261.36779.36383.1885 66.24441.16999.16294.8159 Metal Fiber K Factors for...d...v Elements Size 3µm 5µm 1µm 2µm 6.8788.6368.35672.1811 11.4555.32928.235.11525 16.24696.17562.12622.7683 24.17561.13171.1427.637 28.8232.6586.5488.2744 33.11525.8232.7134.4281 66.637.4939.3293.171 6
Dimensons: DF 6-28 P B11 B12 B8 B9 D4 B3 B5 B7 Hex Indicator Port G 1/2 1 1/16 27 D5 x T1/T2 B14 B15 B1 B6 B4 B2 B1 T3 D2 D3 H3 H1 HEX for bowl removal D1 H2 (Clearance Required for element removal) Size B1 B2 B3 B4 B5 B6 B7 B8 B9 B1 B11 B12 B13 B14 B15 DF 6 P.24 4.9 3.15 3.54 1.252 1.244.295 2.21.949 DF 11 P 6 14 8 89 31.8 31.6 7.5 55.9 24.1 DF 16 P.24 4.53 4.33 3.543 3.386 2.42 2.244 1.496.55.492 2.264.354.472 1.43.41 DF 24 P 6 115 11 9 86 61 57 38 14 12.5 57.5 9 12 26.5 1.5 DF 28 P Size D1 D2 D3 D4 D5 UNC H1 H2 H3 T1 T2 T3 HEX DF 6 P 6.22 Ø.24 Ø.996 Ø.69.33 158 2.95 2.99.79 1 1/16 Ø DF 11 P 68 25.3 17.5 8.5 8.88 75 76 2 27 225.5 DF 16 P 7.83 199 DF 24 P 3.74 1.126.84.35 7/16-14 1.2 3.35 3.27.51.71.79 1 5/16 Ø Ø Ø Ø 95 28.6 21.4 9 259 85 83 13 18 2 32 DF 28 P 17.4 442 Dimensions are in inches/millimeters. Dimensions are for general information only. Due to constant development and updating of details, we ask that all critical dimensions be verified by requesting a certified print. 7
Dimensons: DF 33/66 P B3 B5 D6 B8 B4 B7 B1 H1 H3 H6 H4 B6 T1 B1 Drain G 1/2 H2 (Clearance Required for element removal) D1 D2 D3 D4 D2 B9 D5 B1 H5 Hex 1 1/16 27 Indicator Port G 1/2 HEX for bowl removal Size B1 B2 B3 B4 B5 B6 B7 B8 B9 B1 D1 D2 DF 33 P.24 2.76 3.811 3.311 1.96.658 1.656.843.748 1.996 6.22 5.12 DF 66 P 6 7 96.8 84.1 48.4 16.7 42.5 21.4 19 5.7 158 13 Size D3 D4 D5 D6 H1 H2 H3 H4 H5 H6 T1 HEX DF 33 P 13.35 1.614 1.18.45.24 339 3.74 6.87 3.86 3.78.79.12 1 7/16 DF 66 P 41 3 11.5 6 2.8 95 174.5 98 96 2 2.6 36 51 Dimensions are in inches/millimeters. Dimensions are for general information only. Due to constant development and updating of details, we ask that all critical dimensions be verified by requesting a certified print. Copyright 1999 HYDAC TECHNOLOGY CORPORATION - Brochure - High Pressure Filters for Manifold Mounting Series DF...P #268121 / 7.99 HYDAC TECHNOLOGY CORPORATION 226 City Line Road Bethlehem, PA 1817 Phone (61) 266-1 Fax (61) 264-354 www.hydacusa.com powerup@hydacusa.com