Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Guide Cylinder Series MGG ø, ø, ø, ø, ø, ø, ø, ø Integration of a basic cylinder and guide rods Linear Transfer Unit Guide Cylinder Series MGG Integration of a basic cylinder and guide rods. Long stroke is available. Equipped with a shock absorber as standard. Guide Cylinder/With End Lock Series MGG ore size Long stroke ore size Long stroke 4 6 7 Holds the cylinder's home position even if the air supply is cut off. When air is discharged at the stroke end position, the lock engages to maintain the rod in that position. Standard stroke 75 P. 6 P. 76 (End lock type) MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com asic cylinder with integrated guide rods linear transfer unit that achieves high lateral load Guide cylinder ø, ø, ø, ø, Can be mounted with Two types of compact auto switches. guide rod bearings Slide bearing Excellent wear resistance and heavy load capacity all bushing bearing High precision and smooth operation Standard stroke Cylinder position can be detected ll models have built-in magnets for auto switches. uto switch capable throughout entire stroke range. Non-rotating accuracy improved pplication Example by using two guide rods 4 Pusher Lifter ore size Slide bearing all bushing bearing When the cylinder is retracted (initial value), the non-rotating accuracy without loads or deflection of the guide rods will be below the values shown in the table. grease nipple is provided as standard This allows lubrication of the bearings.
in a compact configuration resistance and non-rotating precision Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Series MGG ø, ø, ø, ø Maximum ø- st ø: 75 to st ø to ø: 75 to st Maximum ø- st Maximum ø- 6 st Shock absorbers and adjusting bolts are standard. Stroke end shock absorption for high speed operation and fine stroke adjustment are possible. End lock option introduced to allow holding of cylinder position even when air supply is cut off When air is discharged at the stroke end position, the lock engages to maintain the rod in that position. Long strokes available Maximum ø- st Four mounting styles Maximum ø- st Maximum ø- st Maximum ø- st Maximum ø- st Simple adjustment of extension stroke The extension stroke can be adjusted bymoving the rear plate. () Top mounting () ottom mounting () Side mounting Movement Guide body (4) Front flange mounting Hexagon socket head cap screw ear plate full range of made-to-order specifications Close 5 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com M L Guide Cylinder Series MGG ø, ø, ø, ø, ø, ø, ø, ø MGG L Guide Cylinder earing type Slide bearing Mounting style all bushing bearing F asic style Front mounting flange style ore size mm mm mm mm mm mm mm mm 4 V -wire (NPN) Port thread type DC 5 V Nil TN TF 5 V, V V 5 V, V V 5 V, V How to Order c NPT G C MW pplicable uto Switch/efer to pages 7 to 87 for further information on auto switches. Type Special function Electrical entry eed switch Solid state switch Diagnostic indication (-color indication) Water resistant (-color indication) With diagnostic output (-color indication) Grommet Connector Grommet Indicator light Yes Yes Yes No Yes No Yes No Wiring (Output) -wire (NPN) -wire (PNP) -wire -wire (PNP) -wire 4-wire (NPN) -wire (NPN equivalent) pplicable bore ø, ø ø ø to ø ø, ø MN MP M H7C MNW MPW MW H7 H7NF 6 G5 G5P K5 G5W G5PW K5W G5 G5F uto switch Cylinder stroke efer to Standard Stroke on page 7. Load voltage uto switch model Lead wire length (m) (M) Made to Order efer to page 8 for details. Number of auto switches Nil pcs. S pc. n n pcs. Without auto switch Nil (uilt-in magnet) For the applicable auto switch model, refer to the table below..5 (Nil) (L) 5 (Z) Pre-wired None connector (N) pplicable load IC circuit IC circuit IC circuit V Grommet V or less IC circuit V, V (54) 54 V -wire 4 V V or less (64) 64 C7C Connector 4 V or less CC IC circuit Diagnostic indication (-color indication) Grommet (5W) 5W Lead wire length symbols:.5 m Nil (Example) MNW Solid state auto switches marked with are produced upon receipt of order. m M (Example) MNWM D- V/M V/M WV/M (V) types cannot be mounted. m L (Example) MNWL 5 m Z (Example) MNWZ None N (Example) H7CN Since there are other applicable auto switches than listed, refer to page 88 for details. For details about auto switches with pre-wired connector, refer to pages 784 and 785. D- /M /M W auto switches are shipped together (not assembled). (Only switch mounting brackets are assembled at the time of shipment.) 6 IC circuit elay, PLC elay, PLC Caution When using auto switches shown inside ( ), stroke end detection may not be possible depending on the One-touch fitting or speed controller model. Please contact SMC in this case.
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Specifications JIS Symbol Standard Stroke Model (earing type) ore size Standard stroke Long stroke 75,,,,,,,,, 4,,, 4,, 6 MGGM(Slide bearing),, 4,, 6, 7, 75,,,, MGGL(all bushing bearing),, 4,, 6, 7,,,,,,, 4,, 6, 7,,,,,, 4,, 6, 7,,,,,,, 4,, 6, 7,,,,,, Intermediate strokes and short strokes other than the above are produced upon receipt of order. Specifications Model asic cylinder ore size ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed asic cylinder Cushion Guide unit Stroke adjusting range (One side) [uilt-in adjusting bolts ( pcs.)] ase cylinder lubrication Stroke length tolerance Non-rotating accuracy Slide bearing all bushing bearing MGG to mm MGG MGG MGG MGG MGG MGG MGG CDGN ore size Port thread type Stroke uto switch +. +. Double acting ir.5 MPa. MPa.5 MPa (Horizontal with no load) to mm/s ubber bumper uilt-in shock absorbers ( pcs.) to 5 mm Non-lube +. mm( st or less), mm( st or more) +. to 7 mm/s Piping port size (c, NPT, G) /8 /4 /8 / When the cylinder is retracted (initial value), the non-rotating accuracy without loads or deflection of the guide rods will be below the values shown in the table above as a guideline. Shock bsorber Specifications Shock absorber model 7 4 5 7 pplicable guide cylinder MGG MGG, MGG,, MGG, Maximum energy absorption (J) 5.88.6 58.8 47 Stroke absorption 7 5 Maximum collision speed (m/s) 5 Max. operating frequency (cycle/min) 7 45 mbient temperature range ( C) to Spring force (N) Extended etracted 4. 6.86 6.86 5.8 8.4.5 8.8. It denotes the values at the maximum energy absorption per one cycle. Therefore, the operating frequency can be increased according to the energy absorption. 7 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Theoretical Output Mass ore size L Type (all bushing bearing, asic style).7.8.84 7...6 6. 7.46 LF Type (all bushing bearing, Front mounting flange style).44.7 4.87.8 4.7.58 45.8 M Type (Slide bearing, asic style).7.7.6 7.7.6..6 6.6 MF Type (Slide bearing, Front mounting flange style).4.75 4..7.8.. 44.8 dditional mass per each mm of stroke.4.7..4.6.8..48 dditional mass for long stroke.....6...6 dditional mass with bracket..8...6.6.84.548 Calculation: (Example) MGGL- (all bushing bearing) (asic type, ø, st, With bracket) Standard mass.84 (L type) dditional mass for long stroke. dditional mass for stroke./ st dditional mass with bracket. Stroke st.84 +. x / +. +. = 6.7 kg Mass of Moving Parts 8 OUT ore size Moving parts basic mass dditional mass by each mm of stroke.6..4..6...6 Calculating mass of moving parts (Example): MGGL- Moving parts basic mass.6 dditional mass for stroke./ st Stroke st.6 +. x / =.64 kg IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT OUT 78 57 IN 7 4 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm ) asic mass ore size od size Operating direction IN Piston area (mm ) 4 64 4 4 4 6 6 6 45. 6.8 5.8 8. 8.4 8 64 56 8. 4. 7. 47 4 4 7 78 8 588 45 6 8 5 6 6 Operating pressure (MPa).4 6 6 5 76 4 44 784 66 8 86.5 57 46 6 46 5 8 56 7.6 88 58 5 47 48 45 756 6 87 7 47 4.7 85 44 88 5 484 88 74 7 6 5 (kg) (kg) 5. 8.. 8.58..67.48.65 Symbol X6 X XC4 XC6 XC8 XC XC XC XC XC XC7 XC56 XC7 XC7 XC7 XC7 XC8 X4 X77 OUT.8 64 55 848 57 6 57. 8 8 44 7 74 6 54 76 4 8 45 77 64 IN Made to Order Specifications (For details, refer to pages 8 to.). 4 64 4 4 4 6 6 6 45 78 7 (N) Specifications Heat resistant cylinder ( C) Low speed cylinder (5 to mm/s) With heavy duty scraper Made of stainless steel djustable stroke cylinder/djustable extension type djustable stroke cylinder/djustable retraction type Dual stroke cylinder/single rod type uto switch rail mounting Fluororubber seals With coil scraper Larger throttle diameter of connecting port With knock pin hole Helical insert thread specifications Not possible for built-in magnet for auto switch Cylinder with lock (CDNG) Machining tapped hole, drilled hole, and pin hole additionally Cylinder with lock (MDN) With piping ports for grease With piping ports for grease, auto switch rail mounting style 8
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com ir-hydro Low pressure hydraulic cylinder of. MPa or less When used together with a Series CC air-hydro unit, constant and low speed actuation, and intermediate stopping similar to hydraulic units are possible with the use of valves and other pneumatic equipment. MGGH earing type Mounting style ore size Port thread type Stroke MGGM Mounting style ore size Port thread type ir-hydro Specifications ore size,,,,, ction Double acting Fluid Turbine oil Proof pressure.5 MPa Maximum operating pressure. MPa Minimum operating pressure.8 MPa (Horizontal with no load) Piston speed 5 to mm/s Cushion asic cylinder None Guide unit uilt-in shock absorbers ( pcs.) mbient and fluid temperature +5 to 6 C Mounting asic style Front mounting flange style For specifications other than the above, refer to page 7. uto switch can be mounted. Dimensions (Dimensions other than the above are the same as the standard type.) Front mounting flange ø to ø ø Y + Stroke Front mounting flange ore size Y Y + Stroke 4 7 4 7 4 8 5 8 4 Copper and Fluorine-free (For CT production processes) To prevent the influence of copper ions or halogen ions during CT manufacturing processes, copper and fluorine materials are not used in the component parts. -MGG earing type Mounting style ore size Port thread type Stroke Copper and Fluorine-free Specifications ore size,,,,,,, ction Double acting Fluid ir Maximum operating pressure. MPa Minimum operating pressure.5 MPa (Horizontal with no load) Cushion asic cylinder ubber bumper Guide unit uilt-in shock absorbers ( pcs.) Mounting asic style Front mounting flange style For specifications other than the above, refer to page 7. For dimensions, refer to pages 7 to 75. uto switch can be mounted. Water esistant The installation of a special scraper in front of the rod seal on the base cylinder protects against the entry of liquids from the environment into the cylinder. This type can be used in environments with machine tool coolants, and with water spray such as food processing and car washing equipment. Slide bearing Dimensions ø to ø ø to ø Water resistant cylinder N seals (Nitrile rubber) V FKM seals (Fluororubber) X X Q Y + Stroke Q H7L G5L Stroke Water resistant -color indication solid state auto switch ø to ø ø, ø ore size Q 7 4 46 47 X 48 58 6 56 68 68 ( ): Denotes the dimensions for long stroke. H7L -XC6 Made to Order Specifications Specifications ore size ction earing type Cushion uto switch mounting XC6,,,,, Double acting Slide beaning ubber bumper uilt-in shock absorbers and mounting Piston rod and rod end nut made of stainless steel Made to Order XC6 XC6 XC6C Stainless steel used for all iron parts Stainless steel rod end moving parts Stainless steel rods Specifications other than the above is the same as the standard type. Note) L (coolant resistant) type shock absorber is used. (Dimensions other than the above are the same as the standard type.) Front mounting flange Front mounting flange Y + Stroke Y 77 (85) 84 () 7 () (4) 7 (5) 8 (5) MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Slide earing llowable End Load and Deflection MGGM - Stroke MGGM - Stroke MGGM - Stroke Deflection Y.5 MGGM - Stroke Deflection Y 6 5 4 st st st: Stroke st st 6 MGGM - Stroke Deflection Y 8 7 6 5 4 (Slide bearing type) st st: Stroke st 75st llowable end load F (N) st st st st 7st 7st 6st 6st 4 st llowable end load F (N) st st st (Slide bearing type) st: Stroke st 75st 6 7 llowable end load F (N) (Slide bearing type) (Slide bearing type) st: Stroke st st st 6 6 st st F st Y st st Deflection Y llowable end load F (N) Deflection Y 4.5 4 6st st st st (Slide bearing type) st st: Stroke st 6 llowable end load F (N) 6
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Deflection Y 7.5 7 6 5 4 MGGM Deflection Y 8 7 6 5 4 st st st MGGM - Stroke - Stroke st MGGM - Stroke Deflection Y 7st 6st st st st st st (Slide bearing type) st: Stroke 6 6 6 llowable end load F (N) st st st st st 7st 6st (Slide bearing type) st: Stroke st st st 4 5 6 8 7 6 5 4 st st st st st st 7st 6st st st llowable end load F (N) (Slide bearing type) st: Stroke st st st 4 5 6 6 7 7 st st llowable end load F (N) 6 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com MGGL - Stroke MGGL - Stroke MGGL - Stroke Deflection Y.5 st (all bushing bearing type) st st st MGGL - Stroke Deflection Y MGGL - Stroke Deflection Y 4 st: Stroke 75st llowable end load F (N) st Deflection Y.5 st st (all bushing bearing type) st st st: Stroke st 75st 6 llowable end load F (N) (all bushing bearing type) st: Stroke 6 llowable end load F (N) st st 7st 7st 6st 6st st st st st F Y st st st st all ushing earing llowable End Load and Deflection st st (all bushing bearing type) st: Stroke 6 llowable end load F (N) Deflection Y 4 6st st (all bushing bearing type) st st st st: Stroke st 6 llowable end load F (N) 6
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com MGGL - Stroke Deflection Y.5 MGGL - Stroke Deflection Y st MGGL - Stroke Deflection Y st 7st 6st st st st st st (all bushing bearing type) st: Stroke 6 llowable end load F (N) st st 7st 6st st st st st st (all bushing bearing type) st: Stroke 6 llowable end load F (N) st st st 7st 6st st st st st st (all bushing bearing type) st: Stroke 6 6 llowable end load F (N) MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Slide earing llowable End Load and Deflection MGGM - Stroke MGGM - Stroke MGGM - Stroke Deflection Y..5 st st st st MGGM - Stroke Deflection Y MGGM - Stroke Deflection Y.5.5 (Slide bearing type) st: Stroke 75st llowable end load F (N) Deflection Y.5.5 st st st st (Slide bearing type) st: Stroke st 75st 6 7 llowable end load F (N) (Slide bearing type) st: Stroke.5 st st 6 4.5.5.5 st st st st 7st 7st 6st 6st st st st llowable end load F (N) (Slide bearing type) st: Stroke.5 st st st 6 6 st F Y st llowable end load F (N) Deflection Y..5.5 6st st st st (Slide bearing type) st: Stroke st st 6 llowable end load F (N) 64
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com MGGM - Stroke Deflection Y.7.5.5.5.5 MGGM - Stroke Deflection Y MGGM - Stroke Deflection Y 4.5.5.5.5 st st st st 7st 6st st st st st st (Slide bearing type) st: Stroke 6 6 6 llowable end load F (N) st st st st st 7st 6st st st st llowable end load F (N) (Slide bearing type) st: Stroke st st 4 5 6 4.5.5.5.5 st st st st st st 7st 6st st st st st st (Slide bearing type) st: Stroke 4 5 6 6 7 7 llowable end load F (N) 65 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com MGGL - Stroke MGGL - Stroke MGGL - Stroke Deflection Y..5 st st st st MGGL - Stroke Deflection Y MGGL - Stroke Deflection Y.5.5.5.5 (all bushing bearing type) st: Stroke 75st llowable end load F (N) Deflection Y.7.5.5 st st st (all bushing bearing type) st st: Stroke st 75st 6 llowable end load F (N) (all bushing bearing type) st: Stroke 6 llowable end load F (N) st st 7st st 7st 6st 6st st st st st st F Y st st st st all ushing earing llowable End Load and Deflection st (all bushing bearing type) st: Stroke 6 llowable end load F (N) Deflection Y.5.5 6st st (all bushing bearing type) st st st st: Stroke st 6 llowable end load F (N) 66
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com MGGL - Stroke Deflection Y..5 st MGGL - Stroke Deflection Y MGGL - Stroke Deflection Y.5.5 st 7st 6st st st st st st (all bushing bearing type) st: Stroke 6 llowable end load F (N) st st 7st 6st st st st st st (all bushing bearing type) st: Stroke 6 llowable end load F (N) st st st 7st 6st st st st st st (all bushing bearing type) st: Stroke 6 6 llowable end load F (N) 67 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com llowable Eccentric Load 68 l l Slide earing: MGGM - Stroke llowable eccentric load W (N) llowable eccentric load W (N) P =.5 MPa MGGM - MGGM - MGGM - MGGM - MGGM - MGGM - MGGM - MGGM - Eccentric distance from center of cylinder to load center of gravity l (Set the maximum allowable load so that it does not exceed the following percentages of the theoretical output: % for ø, % for ø, % for ø, 55% for ø and ø, and % for ø, ø and ø.) all ushing earing: MGGL - Stroke P=.5 MPa MGGL - MGGL - MGGL - MGGL - MGGL - MGGL - MGGL - MGGL - Eccentric distance from center of cylinder to load center of gravity l (Set the maximum allowable load so that it does not exceed the following percentages of the theoretical output: % for ø, % for ø, and 6% for ø, ø, ø, ø, ø and ø.)
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Construction ø to ø/mgg Component Parts No. Description od cover Tube cover Piston 4 Piston rod 5 ushing 6 umper 7 umper 8 Magnet etaining ring Wear ring od end nut Piston gasket Head cover 4 Cylinder tube 5 Guide body Small flange Large flange 7 Front plate 8 ear plate Slide bearing all bushing bearing Guide rod 4 6 7 8 ' # @8 # @!7 #5 @ @ @! # #4 View - Material luminum alloy luminum alloy luminum alloy Carbon steel Note White hard anodized White hard anodized Chromated Hard chrome plated ø, ø are stainless steel earing alloy Urethane Urethane ø and larger are the same as bumper Stainless steal esin olled steel N luminum alloy White hard anodized luminum alloy Hard anodized For long stroke luminum alloy White anodized olled steel For basic style For front mounting flange style olled steel Cast iron earing alloy Platinum silver For slide bearing For ball bushing bearing Carbon steel Hard chrome plated For slide bearing High carbon chrome bearing steel Quenched, hard chrome plated For ball bushing bearing End bracket Carbon steel Flat washer olled steel Spring washer Steel wire Felt Felt Holder Stainless steel Type C retaining ring for hole Carbon tool steel racket Stainless steel Shock absorber!6 #8 qt $ w r!5! @4 @5 @6 y#! i! e u o @ #6!8 Front mounting flange style!4 $ Long stroke # @7 #7! Component Parts No. Description Material Note djusting bolt Nut Parallel pin Grease nipple olled steel olled steel High carbon chrome bearing steel 4 Hexagon socket head cap screw Chromium molybdenum steel Hexagon socket head cap screw Chromium molybdenum steel For cylinder mounting For large/small flange mounting Guide bolt Chromium molybdenum steel For front plate mounting 6 7 Hexagon socket head cap screw Chromium molybdenum steel Hexagon socket head cap screw Chromium molybdenum steel For rear plate mounting For bracket mounting 8 od seal Piston seal Tube gasket N N N eplacement Parts: Seal Kit all bushing bearing ore size Kit no. Contents CGN-PS CGN-PS Set of nos. above #8, #, $. CGN-PS CGN-PS Seal kit includes #8 to $. Order the seal kit, based on each bore size. Seal kit includes a grease pack ( g). Order with the following part number when only the grease pack is needed. Grease pack part no.: G-S- ( g) Caution When disassembling cylinders with bore sizes of ø through ø, grip the double flat part of either the tube cover or the rod cover with a vise and loosen the other side with a wrench or an adjustable angle wrench, and then remove the cover. When re-tightening, tighten approximately degrees more than the original position. (Cylinders with ø or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. Please contact SMC when disassemble is required.)! Slide bearing 6 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Construction ø to ø/mgg ø @! ' Component Parts @ @7 @ @!! # # No. Description Material Note 4 5 6 7 8 od cover Tube cover Piston Piston rod ushing umper Magnet etaining ring Wear ring luminum alloy luminum alloy luminum alloy Carbon steel earing alloy Urethane Stainless steel esin White hard anodized White hard anodized Chromated Hard chrome plated Not required for ø and ø od end nut Piston gasket olled steel N ø is carbon steel Head cover luminum alloy White hard anodized Cylinder tube luminum alloy Hard anodized For long stroke 4 5 Guide body Front plate ear plate luminum alloy olled steel Cast iron Platinum silver Flat nickel plated Platinum silver 7 Slide bearing earing alloy For slide bearing all bushing bearing For ball bushing 8 Guide rod Carbon steel Hard chrome plated For slide bearing High carbon chrome bearing steel Quenched, hard chrome plated For ball bushing bearing End bracket Carbon steel Flat nickel plated Flat washer olled steel Not required for ø 4 Spring washer Felt Holder Type C retaining ring for hole Steel wire Felt olled steel Carbon tool steel #!5 #6 qt#8!4!7 @ @ @4 rye#7 uo! iw!8 #4!6 # @6 @8!7 View - Slide bearing ø, ø @5 #5 y Component Parts all bushing bearing! #8! Long stroke No. Description Material Note 6 7 8 racket Shock absorber djusting bolt Nut Parallel pin Grease nipple Flat washer luminum alloy olled steel olled steel High carbon chrome bearing steel Carbon steel White anodized 4 Hexagon socket head cap screw Chromium molybdenum steel Hexagon socket head cap screw Chromium molybdenum steel Hexagon socket head cap screw Chromium molybdenum steel Hexagon socket head cap screw Chromium molybdenum steel For cylinder mounting For front plate mounting For rear plate mounting For bracket mounting 6 7 8 od seal Piston seal Tube gasket N N N Caution asic cylinders with a bore size of ø cannot be disassembled. (Cylinders with ø or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. Please contact SMC when disassemble is required.) 7
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Construction ø to ø/mgg F ø @! Component Parts ' @ @7 #!5 # #6 qt#8!4!7 @ @ @4 r y e #7 uo! iw!8 #4!6 @ @!! # $ @6 No. Description Material Note 4 5 6 7 8 od cover Tube cover Piston Piston rod ushing umper Magnet etaining ring Wear ring luminum alloy luminum alloy luminum alloy Carbon steel earing alloy Urethane Stainless steel esin White hard anodized White hard anodized Chromated Hard chrome plated Not required for ø and ø od end nut Piston gasket olled steel N ø is carbon steel Head cover luminum alloy White hard anodized Cylinder tube luminum alloy Hard anodized For long stroke 4 5 Guide body Front plate ear plate luminum alloy olled steel Cast iron Platinum silver Flat nickel plated Platinum silver 7 Slide bearing earing alloy For slide bearing all bushing bearing For ball bushing 8 Guide rod Carbon steel Hard chrome plated For slide bearing High carbon chrome bearing steel Quenched, hard chrome plated For ball bushing bearing End bracket Carbon steel Flat nickel plated Flat washer olled steel Not required for ø 4 Spring washer Felt Holder Type C retaining ring for hole racket Steel wire Felt olled steel Carbon tool steel luminum alloy White anodized @8 View - # Slide bearing y Component Parts No. 6 7 8 4 6 7 8!7 @5 ø, ø #5 all bushing bearing Description Material Shock absorber djusting bolt olled steel Nut olled steel Parallel pin High carbon chrome bearing steel Grease nipple Hexagon socket head cap screw Chromium molybdenum steel Hexagon socket head cap screw Chromium molybdenum steel Hexagon socket head cap screw Chromium molybdenum steel Hexagon socket head cap screw Chromium molybdenum steel od seal N Piston seal N Tube gasket N Large flange olled steel Hexagon socket head cap screw Chromium molybdenum steel Long stroke Note! #8! For cylinder mounting For front plate mounting For rear plate mounting For bracket mounting Flat For large flange mounting Caution asic cylinders with a bore size of ø cannot be disassembled. (Cylinders with ø or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. Please contact SMC when disassemble is required.) 7 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Dimensions asic style: MGG ø to ø I ore size N M J Stroke range 75,,,, 75,,, 4 x O K L 7 C D E 4 4 7 ore size * O P Q M6 x depth M6 x depth M6 x depth M8 x. depth M x.5 depth /8 /8 /8 /8 /4 4 Note) c, NPT and G ports can be selected. 7.5 7.5 4 75 85 S X 6 8 47 58 C F M5 x.8 depth M6 x depth M6 x depth M8 x. depth 45 M x.5 depth T C Q L U 8 4 8 4 V 48 57 65 84 4 D x P (c, NPT, G) Y + Stroke Z + Stroke D E W 46 5 6 75 E øs L 6 6 6 X 46 46 56 67 P 45 C 8 5 7.5 7 4 Y 7 7 7 4 x øf through, counterbore øg ottom 4 x H racket (efer to the table below.) 8 x F Z 57 75 8 85 D 6 65 E øt F G H 8 7 5.5 6.6 6.6.5 depth 6 M8 x. depth 4 depth 8 M x.5 depth 8 depth 8 M x.5 depth 8 4 depth M x.75 depth 7 depth M4 x depth 55 Long Stroke ore size Stroke range to to to 6 to to 4 4 4 5 Y 7 7 8 8 4 U W I J 55 65 7 K 6 7 5 5 ore size P V L 4 5 M 56 N 45 54 6 75 racket Mounting Stroke racket mounting stroke st or more st or more st or more st or more st or more 7
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Dimensions asic style: MGG ø to ø I ore size ore size N M J Stroke range 75,,, O 4 x O K L ø piston rod end connection M x.75 depth M x.75 depth 8 M4 x depth /4 /8 / Note) c, NPT and G ports can be selected. P X Y + Stroke Z + Stroke Q C C 4 D 5 7 7 5 7.5 45 C Q S E 7 8 T U D x P (c, NPT, G) D F E V 8 4 8 6 4 øs P M x.75 depth 4 6 55 M x.75 depth 4 7 7 M4 x depth 8 W 86 4 8 X 8 6 4 54 66 66 8 x F Y 4 x øf through, counterbore øg ottom 4 x H racket (efer to the table below.) C Z D 7 8 5 4 E E F Long Stroke ore size øt G 7 4.5 depth 4.5.5 depth 4.5 M x depth 8 M x depth 8 65 75 74 5 depth 7 M8 x.5 depth 85 Stroke range to to to H U W Y 45 45 I J K racket Mounting Stroke ore size L 7 8 4 5 45 P V M 66 76 N 5 racket mounting stroke st or more st or more st or more MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual 7
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Dimensions Front mounting flange style: MGG F ø to ø H G 4 x øk hole ore size Stroke range 75,,,, I N M J I J 75,,, 7 4 x O 4 4 7 K L ore size * P Q S T /8 /8 /8 /8 /4 4 4 6 8 47 58 Note) c, NPT and G ports can be selected. G H 4 4 7 86 U 8 4 8 4 V 48 57 65 84 4 W X 46 5 6 75 I 8 4 X Q 46 46 56 67 L J 5 8 8 x P (c, NPT, G) Y 7 7 7 K 6.6 Z 57 75 8 85 L øs Y + Stroke Z + Stroke M N 65 5 75 85 5 75 5 ore size O M6 M8 M8 M8 M Long Stroke racket (efer to the table below.) P 45 øt 8 7 4 Stroke range to to to 6 to to I 55 4 4 4 5 J 55 65 7 Y 7 7 8 8 4 U W K 6 7 5 5 Cutout window L 4 5 M 56 ore size G N N 45 54 6 75 V M P Mounting dimensions racket Mounting Stroke O M6 x depth M6 x depth M6 x depth M8 x. depth M x.5 depth racket mounting stroke st or more st or more st or more st or more st or more For 4 x O I 74
Guide Cylinder Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Dimensions Front mounting flange style: MGG F ø to ø H G 4 x øk hole ore size ore size Stroke range 75,,, Q I 4 N M J I J S 7 8 T 4 x O U K L ø piston rod end connection V 8 4 8 6 4 Note) c, NPT and G ports can be selected. G H W 86 4 8 X X 54 66 66 Q L I Y J 8 58 7 6 84 78 6 6 Z 7 8 5 4 x P (c, NPT, G) K 4 4 øs Y + Stroke Z + Stroke L M N O P Long Stroke ore size 4 M 55 68 M 75 M4 Stroke range to to to racket (efer to the table below.) 6 7 8 6 4 Y 45 45 øt I 65 75 85 J K racket Mounting Stroke ore size U W L 7 8 4 5 45 Cutout window M 66 76 N G N racket mounting stroke st or more st or more st or more V M P Mounting dimensions O I M x.75 depth 5 M x.75 depth 8 M4 x depth For 4 x O P * /4 /8 / MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual 75
Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Guide Cylinder mm mm mm mm M L MGG L earing type Slide bearing all bushing bearing Mounting style F ore size mm mm mm mm asic style Front mounting flange style Port thread type Nil c TN NPT TF G Cylinder stroke efer to Standard Stroke on page 77. 4 V -wire (NPN) DC 5 V, V V 5 V, V V 5 V, V 5 V How to Order C H N MW Manual release type N Non-lock type L Lock type Lock position H Head end lock od end lock pplicable uto Switch/efer to pages 7 to 87 for further information on auto switches. Type Special function Electrical entry eed switch Solid state switch Diagnostic indication (-color indication) Water resistant (-color indication) With diagnostic output (-color indication) Grommet Connector Grommet Indicator light Yes Yes Yes No Yes No Yes No Wiring (Output) -wire (NPN) -wire (PNP) -wire -wire (PNP) -wire 4-wire (NPN) -wire (NPN equivalent) Load voltage uto switch model Lead wire length (m) pplicable bore ø, ø ø ø to ø ø, ø MN MP M H7C MNW MPW MW H7 H7NF 6 G5 G5P K5 G5W G5PW K5W G5 G5F.5 (Nil) (M) (L) Made to Order efer to page 78 for details. Number of auto switches Nil pcs. S pc. n n pcs. uto switch Without auto switch Nil (uilt-in magnet) For the applicable auto switch model, refer to the table below. 5 (Z) Pre-wired None connector (N) pplicable load IC circuit IC circuit IC circuit V Grommet V or less IC circuit V, V (54) 54 V -wire 4 V V or less (64) 64 C7C Connector 4 V or less CC IC circuit Diagnostic indication (-color indication) Grommet (5W) 5W Lead wire length symbols:.5 m Nil (Example) MNW Solid state auto switches marked with are produced upon receipt of order. m M (Example) MNWM D- V/M V/M WV/M (V) types cannot be mounted. m L (Example) MNWL 5 m Z (Example) MNWZ None N (Example) H7CN Since there are other applicable auto switches than listed, refer to page 88 for details. For details about auto switches with pre-wired connector, refer to pages 784 and 785. D- /M /M W auto switches are shipped together (not assembled). (Only switch mounting brackets are assembled at the time of shipment.) 76 Guide Cylinder/With End Lock Series MGG ø, ø, ø, ø, ø, ø, ø, ø IC circuit elay, PLC elay, PLC Caution When using auto switches shown inside ( ), stroke end detection may not be possible depending on the One-touch fitting or speed controller model. Please contact SMC in this case.
Guide Cylinder/With End Look Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Specifications JIS Symbol Head end lock Standard Stroke Model (earing type) ore size Standard stroke Long stroke 75,,,,,,,,, 4,,, 4,, 6 MGGM(Slide bearing),, 4,, 6, 7, 75,,,, MGGL(all bushing bearing),, 4,, 6, 7,,,,,,, 4,, 6, 7,,,,,, 4,, 6, 7,,,,,,, 4,, 6, 7,,,,,, Intermediate strokes and short strokes other than the above are produced upon receipt of order. Specifications Model MGG MGG MGG MGG MGG MGG MGG MGG asic cylinder CDGN ore size Port thread type Stroke Lock position Manual release uto switch XC7 ore size ction Double acting Fluid ir Proof pressure.5 MPa Maximum operating pressure. MPa Minimum operating pressure.5 MPa (Horizontal with no load) mbient and fluid temperature Piston speed to mm/s to 7 mm/s asic cylinder ubber bumper Cushion Guide unit uilt-in shock absorbers ( pcs.) Stroke adjusting range (One side) [uilt-in adjusting bolts ( pcs.)] to mm to 5 mm ase cylinder lubrication Non-lube +. +. Stroke length tolerance +. mm( st or less), +. mm( st or more) Non-rotating Slide bearing accuracy all bushing bearing Piping port size (c, NPT, G) /8 /4 /8 / When the cylinder is retracted (initial value), the non-rotating accuracy without loads or deflection of the guide rods will be below the values shown in the table above as a guideline. Lock Specifications ore size Holding force (Max.) (N) 5 5 86 Lock position Head end, od end acklash mm or less Manual release Non-lock type, Lock type djust switch positions for operation at both the stroke end and backlash ( mm) movement positions. Shock bsorber Specifications Shock absorber model pplicable guide cylinder Maximum energy absorption (J) Stroke absorption Maximum collision speed (m/s) Max. operating frequency (cycle/min) mbient temperature range ( C) 7 MGG 5.88 7 7 od end lock 4 5 7 MGG, MGG,, MGG,.6 58.8 5 47 5 Extended 4. 6.86 8.4 8.8 Spring force (N) etracted 6.86 5.8.5. It denotes the values at the maximum energy absorption per one cycle. Therefore, the operating frequency can be increased according to the energy absorption. 45 to 4 5 77 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Theoretical Output ore size od size 8 Operating direction OUT ore size (kg) L Type (all bushing bearing, asic style) LF Type (all bushing bearing, Front mounting flange style) M Type (Slide bearing, asic style) MF Type (Slide bearing, Front mounting flange style) dditional mass per each mm of stroke dditional mass for long stroke dditional mass with bracket Non-lock type (N).7.44.7.4.4...5.8.7.7.75.7..8.7.84 4.87.6 4.....8 7..8 7.7.7.4...7. 4.7.6.8.6.6.6.6.6.58...8..6.44 6..6....84.8 7.46 45.8 6.6 44.8.48.6.548.5 Head end lock (H) od end lock () Lock type (L) Non-lock type (N) Lock type (L).7.7..8.8....4......4.48.5.54.88..7... Calculation: (Example) MGGL--HN (all bushing type) (asic style, ø, st, With bracket) Standard mass.84 (L type) dditional mass for long stroke. dditional mass for stroke./ st dditional mass with bracket. Stroke st dditional mass of lock unit.8.84 +. x / +. +.+.8 = 6.45 kg (Head side, Non-lock type) ore size Moving parts basic mass.6.4.6. dditional mass by each mm of stroke....6 Calculating mass of moving parts (Example) MGGL--HN Moving parts basic mass..6 dditional mass for stroke./ st Stroke st.6 +. x / =.64 kg IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT OUT 78 57 IN 7 4 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm ) Mass asic mass dditional mass of lock unit Mass of Moving Parts IN Piston area (mm ) 4 64 4 4 4 6 6 6 45. 6.8 5.8 8. 8.4 8 64 56 8. 4. 7. 47 4 4 7 78 8 588 45 6 8 5 6 6 Operating pressure (MPa).4 6 6 5 76 4 44 784 66 8 86.5 57 46 6 46 5 8 56 7.6 88 58 5 47 48 45 756 6 87 7 47 4.7 85 44 88 5 484 88 74 7 6 5 (kg) 5. 8.. 8.58..67.48.65 Symbol -XC7 OUT.8 64 55 848 57 6 57. 8 8 44 7 74 6 54 76 4 8 45 77 64 IN Made to Order Specifications (For details, refer to page 847.) Specifications. 4 64 4 4 4 6 6 6 45 78 7 Machining tapped hole, drilled hole and pin hole additionally (N) 78 efer to pages 6 to 68 for the allowable end load and deflection, as well as the allowable eccentric load.
Guide Cylinder/With End Look Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Construction ø to ø/mgg! @ q t #!4 r y e # i!! u o! Component Parts No. 4 5 6 7 8 4 5 7 8 4 Description od cover Tube cover Piston Piston rod ushing umper umper Magnet etaining ring Wear ring Material luminum alloy luminum alloy luminum alloy Carbon steel earing alloy Urethane Urethane Stainless steel esin Note White hard anodized White hard anodized Chromated Hard chrome plated ø, ø are stainless steel Description is umper for ø and larger ø or larger: Same as umber Not required for ø, ø od end nut Piston gasket olled steel N ø is carbon steel Head cover luminum alloy White hard anodized For head side locking type Cylinder tube luminum alloy Hard anodized and long stroke Lock piston Lock bushing Lock spring umper Carbon steel earing alloy Stainless steel Urethane Hard chrome plated, Heat treated Hexagon socke thead cap screw Chromium molybdenum steel lack zinc chromated Cap Cap luminum die-casted Carbon steel lack painted Oxide film treated For non-lock type For lock type ubber cap Synthetic rubber For non-lock type M/O knob Zinc die-casted lack painted For lock type M/O bolt Chromium molybdenum steel lack zinc chromated, ed painted For lock type M/O spring Front mounting flange style Steel wire Zinc chromated Head end lock w od end lock (ase cylinder only) For lock type ø, ø, ø: Stainless steel! y Component Parts No. Description Material Note 6 Stopper ring Carbon steel Zinc chromated For lock type 7 8 Piston holder Seal retainer od seal Piston seal Tube gasket Lock piston seal Urethane olled steel N N N N Used for ø and larger Used for ø and ø Since the guide unit parts are the same as the standard type, refer to pages 6 to 7. eplacement Parts: Seal Kit ore size!7 @5 @4 @ @6 @ @8 #!6!8!5 ø to ø ø to ø Kit no. CGN-PS CGN-PS CGN-PS CGN-PS Manual release (Lock type) @ @ Contents Set of nos. above @, #, #, #. Seal kit includes @ to #. Order the seal kit, based on each bore size. Seal kit includes a grease pack ( g). Order with the following part number when only the grease pack is needed. Grease pack part no.: G-S- ( g) ø, ø Manual release (Non-lock type) ø, ø ø, ø ø, ø Caution asic cylinders with a bore size of ø cannot be disassembled. (Cylinders with ø or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. Please contact SMC when disassemble is required.) @7 Since the guide unit figure is the same as the standard type, refer to pages 6 to 7. @8 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual 7
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Dimensions asic style: MGG ø to ø Dimensions not marked with an are the same as standard. ore size ore size O P S T M6 x depth M6 x depth M6 x depth M8 x. depth M x.5 depth /8 /8 /8 /8 /4 6 8 47 58 Note) c, NPT and G ports can be selected. Long Stroke ore size I N M J 4 x O K L Stroke range 75,,,, 75,,, Stroke range to to to 6 to to 7 4 4 7 racket Mounting Stroke ore size X C 7.5 7.5 U C C 8 4 8 4 Q L D 75 85 V 48 57 65 84 4 E W 46 5 6 75 racket mounting stroke st or more st or more st or more st or more st or more D x P (c, NPT, G) øs E D E od end lock Q Y + Stroke Z + Stroke X 46 46 56 67 Y + Stroke Head end lock F M5 x.8 depth M6 x depth M6 x depth M8 x. depth 45 M x.5 depth Z 57 75 8 85 L 6 6 6 4 x øf through, counterbore øg ottom 4 x H 8 x F P ore size racket (efer to the table below.) øt C D E For lock type For non-lock type HN H 7. 8. 4. 5.5 8. 58.5 44.5 F U W 8 5 7.5 6 65 8 5.5.5 depth 6 M8 x. depth 4 6.6 depth 8 M x.5 depth 8 6.6 depth 8 M x.5 depth 8 45 7 4 depth M x.75 depth 4 7 7 depth M4 x depth 55 G H H P V Non-lock type I ore size od end lock Head end lock Q 8.5 4 47 (4) (4) (4) (5) 4() Y 8() 8() () (8) (7) Q 4 Y 5 5 7 8 Note) ( ): Denotes the dimensions for long stroke. J HN (Max.) K L 55 65 7 6 7 5 5 4 5 Lock type M 56 N 45 54 6 75
Guide Cylinder/With End Look Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Dimensions asic style: MGG ø to ø I Dimensions not marked with an are the same as standard. ore size ore size O P S T M x.75 depth M x.75 depth 8 M4 x depth /4 /8 / 7 8 Note) c, NPT and G ports can be selected. Long Stroke ore size N M J Stroke range 75,,,, Stroke range to to to 4 x O K L ø piston rod end connection X racket Mounting Stroke ore size C C Q C 5 7 7 5 7.5 45 U Q D V D x P (c, NPT, G) D E W 8 86 4 8 4 6 4 8 racket mounting stroke st or more st or more st or more Y + Stroke Z + Stroke E od end lock Head end lock øs Y + Stroke X 54 66 66 F Z 8 5 4 P M x.75 depth 4 6 55 M x.75 depth 4 7 7 M4 x depth 8 4 x øf through, counterbore øg ottom 4 x H racket (efer to the table below.) 8 x F 8 6 4 ore size C E D øt E F G 7 4.5 depth 4.5 M x depth 8.5 depth 4.5 M x depth 8 65 75 74 5 depth 7 M8 x.5 depth 85 For lock type For non-lock type HN H 5 45 68 5.5 7 64.5 U W H H V I P Non-lock type J HN (Max.) K L 7 8 4 5 45 Lock type M 66 76 N 5 ore size od end lock Head end lock Q 8 85 4() () () Y 4(54) 75(8) (4) Q 5 7 Y 47 8 88 Note) ( ): Denotes the dimensions for long stroke. 8 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Dimensions Front mounting flange style: MGG F ø to ø H G I L J 4 x øk holes X Y + Stroke I Z + Stroke J Dimensions not marked with an are the same as standard. ore size ore size 46 5 6 75 Long Stroke ore size 8 Stroke range 75,,,, W 75,,, X 46 46 56 67 N M Stroke range to to to 6 to to Z 57 75 8 85 7 4 x O K L 4 4 7 HN H 7. 8. 4. 5.5 8. 58.5 44.5 racket Mounting Stroke ore size G H ore size Q Q I J racket mounting stroke st or more st or more st or more st or more st or more x P (c,npt,g) øs K 4 4 7 86 8 4 5 8 8 6.6 For lock type For non-lock type od end lock Y + Stroke Head end lock L P 45 8 7 4 racket (efer to the table below.) øt I 55 J K U W 55 65 7 6 7 5 5 4 5 ore size od end lock Head end lock Q 8.5 4 47 (4) (4) (4) (5) 4() Y 8() 8() () (8) (7) Q 4 Y 5 5 7 8 Note) ( ): Denotes the dimensions for long stroke. L M 56 N 45 54 6 75 H P V Non-lock type O M6 x depth M6 x depth M6 x depth M8 x. depth M x.5 depth P /8 /8 /8 /8 /4 HN (Max.) Lock type S 6 8 47 58 T U 8 4 8 4 V 48 57 65 84 4 Note) c, NPT and G ports can be selected.
Guide Cylinder/With End Look Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Dimensions Front mounting flange style: MGG F ø to ø H G 4 x øk holes ore size ore size 86 4 8 Long Stroke ore size I Stroke range 75,,,, W N M J I J X 54 66 66 Stroke range to to to Z 8 5 4 4 x O K L ø piston rod end connection Dimensions not marked with an are the same as standard. ore size HN H 5 45 68 5.5 7 64.5 racket Mounting Stroke ore size X G H 7 L Q Q I 8 58 6 84 78 6 6 For lock type For non-lock type racket mounting stroke st or more st or more st or more x P (c, NPT, G) J øs Y + Stroke Z + Stroke od end lock Y + Stroke Head end lock K 4 4 L racket (efer to the table below.) P 6 7 8 6 4 I 65 75 85 øt J K 7 8 4 5 45 ore size od end lock Head end lock Q 8 85 4() () () Y 4(54) 75(8) (4) Q 5 7 Y 47 8 88 Note) ( ): Denotes the dimensions for long stroke. L U W M 66 76 N H P V Non-lock type O M x.75 depth 5 M x.75 depth 8 M4 x depth P /4 /8 / HN (Max.) S 7 8 Lock type T U V 8 4 8 6 4 Note) c, NPT and G ports can be selected. MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual 8
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com uto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height D- D-M/M W D-C7/C8 D-H7 D-5/6 D-G5/K5 D-7/8 D-G7/K7 uto Switch Proper Mounting Position uto switch model ore size D- 4 4 (8) (8) () () 8 () 8 () D-M D-M W 4 46 46 4 () 4 () () 7 (6) (6) (6).5.5 (.5).5.5 (.5).5.5 (.5) 6.5 4.5 (.5) 4.5.5 (4.5).5 4.5 (4.5) *( ): Set values for long stroke, double rod Note) djust the auto switch after confirming the operating conditions in the actual setting. 84 ~= Hs ~ = D-7/8 D-C7 D-7C D-C D-C D-C7C D-G7/K7 D-CC D-K7C.5.5.5.5 4.5 4.5.5 (8.5).5 (8.5).5 (.5).5 (.5) 8.5 (.5) 8.5 (.5).5 ~= Hs ~ =.5 ~= Hs ~ = 4.5 4.5 ~= Hs ~ = 4.5 D-5 D-64.5.5 4.5.5 6.5 6.5 46.5 46.5 5.5 (.5) 5.5 (.5) 5.5 (.5) (6.5).5 (4.5).5 (4.5).5 (44.5).5 (44.5) D-5W 6.5 6.5 7.5.5.5 4.5 4.5 7.5 (.5) 7.5 (.5) 8.5 (6.5).5 (.5).5 (7.5).5 (7.5).5 (47.5).5 (47.5) D-H7 D-H7C D-H7NF D-H7 W D-H7L 8.5 8.5.5 4.5 4.5 4.5.5 (7.5).5 (7.5).5 (8.5).5 (.5) 7.5 (.5) 7.5 (.5) 8.5 8.5 8.5 8.5 D-G5F D-G5 D-K5 D-G5 W D-K5W D-G5NTL D-G5L 6 8 8 48 48 (4) (4) 7 () (8) 4 (6) 4 (6) (46) (46) uto Switch Mounting Height uto switch model ore size uto switch D- D-M/M W uto switch D-C7/C8 D-H7 uto switch D-5/6 D-G5/K5 uto switch D-7/8 D-G7/K7 D- D-M D-M W Hs 4 6.5 4.5 47 D-C7 D-C D-H7 D-H7 W D-H7NF D-H7L Hs 4.5 7.5.5 47.5 D-C7C D-CC Hs 7.5 7.5 4 D-7/8 D-7C D-C D-G7/K7 D-K7C D-H7C Hs 7.5.5 8 4.5.5 D-G5/K5 D-G5 W D-K5W D-G5NTL D-5/6 D-5W D-G5L D-G5F Hs 7.5.5 8 4.5.5 5 6.5
Guide Cylinder/With End Look Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com uto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height/End Lock Type: With Head End Lock D- D-M/M W D-C7/C8 D-H7 D-5/6 D-G5/K5 D-7/8 D-G7/K7 uto Switch Proper Mounting Position uto switch model D- ore size 4 4 44 44 45 54 64 68 D-M D-M W 4 46 46 48 48 4 58 68 7 ~= Hs ~ = ~= Hs ~= Hs.5.5 6.5 4.5 4.5 45.5 46.5 55.5 65.5 6.5.5.5.5 4.5 4.5 44.5 45.5 54.5 64.5 68.5.5 ~=.5 ~= 4.5 4.5 ~= Hs ~ = 4.5 D-G5F D-7/8 D-H7 D-G5 D-C7 D-7C D-H7C D-K5 D-C D-5 D-C D-C7C D-64 D-5W D-H7NF D-G5 W D-G7/K7 D-H7 W D-K5W D-CC D-K7C D-H7L D-G5NTL D-G5L.5 45.5.5 44.5.5 8.5 6.5 4.5 8.5 4.5.5 4.5.5 6.5 6.5 46.5 46.5 8.5.5 48.5 58.5 6.5 8.5 87.5 6.5 7.5.5.5 4.5 4.5 4.5 4.5 5.5 6.5 65.5 84.5.5 8.5.5 4.5 4.5 4.5 4.5 44.5 5.5.5 67.5 8.5 8.5 8.5 8.5 6 8 8 48 48 4 6 64 8 8 uto Switch Mounting Height uto switch model ore size uto switch D- D-M/M W uto switch D-C7/C8 D-H7 uto switch D-5/6 D-G5/K5 uto switch D-7/8 D-G7/K7 D- D-M D-M W Hs 4 6.5 4.5 47 D-C7 D-C D-H7 D-H7 W D-H7HF D-H7L Hs 4.5 7.5.5 47.5 D-C7C D-CC Hs 7.5 7.5 4 D-7/8 D-7C D-C D-G7/K7 D-K7C D-H7C Hs 7.5.5 8 4.5.5 D-G5/K5 D-G5 W D-K5W D-G5NTL D-5/6 D-5W D-G5L D-G5F Hs 7.5.5 8 4.5.5 5 6.5 MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual Note) djust the auto switch after confirming the operating conditions in the actual setting. 85
Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com uto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height/End Lock Type: With od End Lock D- D-M/M W D-C7/C8 D-H7 D-5/6 D-G5/K5 D-7/8 D-G7/K7 uto Switch Proper Mounting Position uto switch model D- ore size 56 56 58 64 75 77 (8) (8) () () 8 () 8 () D-M D-M W 6 6 6 68 7 8 4 () 4 () () 7 (6) (6) (6) 57.5.5 (.5) 57.5.5 (.5) 5.5.5 (.5) 65.5 4.5 (.5) 76.5.5 (4.5).5 78.5 (4.5).5 (8.5).5 (8.5).5 (.5).5 (.5) 8.5 (.5) 8.5 (.5) 4.5 (.5) 4.5 (.5) 5.5 (.5) 7.5 (6.5).5 (4.5).5 (4.5).5 (44.5).5 (44.5) 7.5 (.5) 7.5 (.5) 8.5 (6.5).5 (.5).5 (7.5).5 (7.5).5 (47.5).5 (47.5) *( ): Set values for long stroke, double rod Note) djust the auto switch after confirming the operating conditions in the actual setting. 86 ~= Hs ~ = D-7/8 D-C7 D-7C D-C D-C D-C7C D-G7/K7 D-CC D-K7C 56.5 56.5 58.5 64.5 75.5 77.5.5 ~= Hs ~ =.5 ~= Hs ~ = 4.5 4.5 ~= Hs ~ = 4.5 D-5 D-64.5.5 5.5 58.5 6.5 7.5.5 5.5 D-5W 5.5 5.5 55.5 6 7.5 74.5.5 8.5 D-H7 D-H7C D-H7NF D-H7 W D-H7L 55.5 55.5 57.5.5 74.5 76.5.5 (7.5).5 (7.5).5 (8.5).5 (.5) 7.5 (.5) 7.5 (.5) 8.5 8.5 8.5 8.5 D-G5F D-G5 D-K5 D-G5 W D-K5W D-G5NTL D-G5L 5 5 54 6 7 7 7 (4) (4) 7 () (8) 4 (6) 4 (6) (46) (46) uto Switch Mounting Height uto switch model ore size D- D-M D-M W Hs 4 6.5 4.5 47 uto switch D- D-M/M W uto switch D-C7/C8 D-H7 uto switch D-5/6 D-G5/K5 uto switch D-7/8 D-G7/K7 D-C7 D-C D-H7 D-H7 W D-H7NF D-H7L Hs 4.5 7.5.5 47.5 D-C7C D-CC Hs 7.5 7.5 4 D-7/8 D-7C D-C D-G7/K7 D-K7C D-H7C Hs 7.5.5 8 4.5.5 D-G5/K5 D-G5 W D-K5W D-G5NTL D-5/6 D-5W D-G5L D-G5F Hs 7.5.5 8 4.5.5 5 6.5
Guide Cylinder/With End Look Series MGG Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Minimum uto Switch Mounting Stroke uto switch model D- D-M D-M W D-C7 D-C D-H7 D-H7 W D-H7L/H7NF D-C7C D-CC D-H7C D-5 /64 D-G5 /K5 D-5W D-7 / D-G7/K7 Operating ange uto switch model D- D-M /M W D-7 / D-7C/C D-C7 /C D-C7C/CC D-5 /64 D-5W D-G7/K7/K7C 7 5 8 8 8 8 6 5.5 pc. 6 65 8 5 4 ore size 8 5.5 4 n: No. of auto switches No. of auto switches mounted pcs. n pcs. Same surface Same surface 45 note) 75 45 Note) For cylinders with auto switches D-/M /M W. With auto switches Same surface uto switch model D- D-M D-M W The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. Less than strokes Less than 55 strokes 8 6.5 4 7 7 8 45 + 45 (n-) + 45 (n-) 6 + 45 (n-) 65 + (n-) 75 + 55 (n-) + 45 (n-) uto switch ore size model D-H7 /H7 W D-H7L/H7NF D-H7C D-G5 /K5 D-G5 W/K5W D-G5NTL/G5L D-G5F D-G5NL 4 7 4 5 4 8.5 4 5 4.5 4.5 5.5 5 5 6 45 6.5 6 7 45 6.5.5 6.5 7.5 45 6.5 7.5 45 7 8 Since this is a guideline including hysteresis, not meant to be guaranteed. (ssuming approximately ±% dispersion) There may be the case to change substantially depending on an ambient environment. MGJ MGP MGQ MGG MGC MGF MGZ MGT D- Individual 87