LIFTERS. Engineering. Durability. Power

Engineering Durability Power LIFTERS For years COMP Cams lifters have set the standard for solid roller lifter technology, but today s engine s place an even greater demand on lifters. With today s aggressive cam designs and increased rpm ranges, look to the new COMP Cams Elite Race Solid Roller Lifters.

LIFTER TECH Flat Tappet vs. Roller Tappet Lifters In nearly all circumstances, a good roller camshaft design will outperform its flat tappet counterpart. Among the benefits of roller cams are higher tappet velocity, more lift and more area, along with reduced valve train friction (often a 15+ hp increase) and higher engine rpm with little effect on low speed drivability and power. Roller tappets are also reusable, which makes it possible to swap just the camshaft without the expense of new lifters. And finally, roller tappets are far less prone to wear, allowing higher spring loads, and they are more consistent with today s oils. The biggest advantage with a flat tappet cam and lifters is the up front cost. It can be significantly less expensive to use a flat tappet setup but should you decide to install a new camshaft, flat tappets are not reusable. You will need new lifters as well. Hydraulic vs. Mechanical (Solid) Lifters Both hydraulic and mechanical lifter types look the same from the outside, with both having pushrod seats held in by a retaining clip. In a hydraulic lifter the seat moves by means of a hydraulic valve and oil pressure within the lifter. The mechanical lifter does not have a valve and is solid. The pushrod seat in a solid lifter sits upon an internal step inside the lifter body, preventing it from moving. The hydraulic lifter, on the other hand, has a pushrod seat that sits on top of a moveable hydraulic mechanism which acts like a tiny hydraulic pump. Below this mechanism are a valve and spring that produce an upward force, moving the seat up against the pushrod when the lifter is on the base circle. Solid cam designs require a running clearance or valve lash. Hydraulic cams are the exact opposite. In a standard hydraulic lifter the pushrod takes up all of the clearance and submerges into the lifter s pushrod seat approximately.020"-.070". The distance that the pushrod submerges is known as the pre-load. PROS 1. Minimum amount of maintenance is required once the proper pre-load is set 2. Fully adjustable for any changes in block & cylinder head size HYDRAULIC LIFTERS Setting Valve Lash With A Solid Lifter Camshaft CONS 1. Less stiff at higher engine speeds due to hydraulic valve pumping up with high pushrod forces - forcing oil to squeeze out, reducing the running duration 3. Less valve train noise 2. Effective rpm range is limited PROS 1. More accurate & consistent valve timing throughout the entire rpm range 2. Not adversely affected by higher spring loads or increased engine speeds SOLID LIFTERS CONS 1. Takes longer to properly set up & requires regular maintenance 2. Noisier valve train First, check the spec card that came with your cam for the correct valve lash specifications. All COMP Cams valve lash settings are hot settings (set at normal engine operating temperature) but will work for initial start-up as well. Turn the crankshaft in the direction of normal engine rotation until the exhaust pushrod of the cylinder you are adjusting begins to move upward, opening the valve. Adjust the INTAKE lash by tightening the intake rocker nut with the correct thickness feeler gauge inserted between the valve stem and the rocker tip. Tighten the rocker nut until there is a slight drag when moving the feeler gauge. Next, rotate the engine until the intake pushrod fully opens the valve and then goes halfway back down. Adjust the EXHAUST rocker nut (with correct feeler gauge) using the same procedure. Repeat for all cylinders. After setting your valve lash with the engine cold, start it and follow the appropriate break-in procedures. Due to thermal expansion, your valve lash will now be tighter than it was when the engine was cold. Repeat the adjustment process to ensure that your valve lash matches that specified by your cam card at normal operating temperature. Note: Check with COMP Cams on valve lash settings if using aluminum heads or block. Setting Hydraulic Lifter Pre-load (Adjustable Valve Train) When installing a hydraulic cam, lifters or rocker arms, establishing the correct lifter pre-load improves both performance and engine life. Insufficient pre-load will create excessive valve train noise and wear. Excessive pre-load will cause rough idling and low manifold vacuum, and can even lead to severe engine damage. With an adjustable valve train, proceed as follows: Install the pushrods and rocker arms. Be sure the pushrods are seated correctly in the lifter and rocker arm. Turn the engine over in the direction of rotation until the exhaust pushrod just begins to move upward, opening the valve. Now adjust the INTAKE rocker of that cylinder. Carefully tighten the nut on the intake rocker while spinning the pushrod with your fingertips. You will feel a slight resistance in the pushrod when you have taken up all of the clearance. This is zero lash. Turn the adjusting nut to the specified pre-load typically 1/4-3/4 of a turn, but this will vary based on the lifter number. Turn the engine in its rotation direction until the intake pushrod comes all the way up and almost all the way back down. Now set the EXHAUST rocker to zero lash and add the specified pre-load. Repeat this process for all remaining cylinders. Setting Hydraulic Lifter Pre-load (Non-Adjustable Valve Train) COMP Cams recommends using an adjustable pushrod to check the pre-load. Typically, only one cylinder needs to be checked in this process. After applying lube, install the adjustable pushrods and assemble the valve train. Using the same procedure mentioned earlier, adjust the intake and exhaust valves to zero lash by changing the length of the adjustable pushrod for precise fitment. Order a pushrod that is.020"-.070" longer than the pushrod length at zero lash to ensure the proper pre-load. Short Travel Hydraulic Roller Lifters COMP Cams Short Travel Hydraulic Roller Lifters are the perfect choice for use in mandated hydraulic roller racing classes and high performance/race applications. The limited plunger travel extends the usable rpm range by up to 500+ rpm but still remains a hydraulic lifter while staying as close to a mechanical lifter as possible. See page 280 for more information. 1.800.999.0853 275 LIFTER TECH

HYDRAULIC LIFTERS HYDRAULIC LIFTERS High Energy Hydraulic Lifters Patented orifice metering valve precisely meters oil to the rocker arms Continuous contact between metering valve and pushrod seat is maintained, eliminating excessive oiling at high engine speeds Pushrod seat is made of a special powdered metal iron alloy that is heat-treated for strength and wear resistance Contain a longer piston than conventional hydraulic lifters, which provides more load bearing surface and increases lifter longevity Lightweight check valve disc allows for quicker response, which results in increases in engine speed before valve float Lightweight check valve disc maintains added control at all engine speeds and loads Make Part # Description Seat Ht. AMC 822-16 V8 290-401.904"/109g 1.88" 822-12 6 Cyl. 199-258.904"/109g 1.88" Buick 869-16 V8 350-455.842"/98g 2.05" 869-12 181-252 1962-Present.842"/98g 2.05" Cadillac 869-16 V8 472-500.842"/98g 2.05" 812-16 V8 265-400.842"/94g 1.99" 812-16 V8 396-454.842"/94g 1.99" Chevrolet 812-16 V8 348-409, 1958-65.842"/94g 1.99" 812-12 6 Cyl. 194-292.842"/94g 1.99" 802-12 V6 60º 173, 207, 2.8L-3.4L.842"/96g 2.05" 812-12 V6 90º 200-262.842"/94g 1.99" 822-16 V8 273-360.904"/109g 1.88" 824-16 V8 B-383-440, 1958-67.904"/110g 1.91" Chrysler 822-16 V8 B-383-440, 1968-Present.904"/109g 1.88" 824-16 Hemi 426.904"/110g 1.91" 820-12 6 Cyl. 170-225, 1980-Present.904"/102g 1.88" 842-8 2.2L 4 Cyl..626"/46g 2.05" 832-16 V8 289-302-351W.875"/105g 2.05" 832-16 V8 351C-351M-400M.875"/105g 2.05" 834-16 V8 352-428.875"/97g 1.88" 832-16 V8 429-460.875"/105g 2.05" Ford 832-12 6 Cyl. 240-300.875"/105g 2.05" 834-12 6 Cyl. 144-250.875"/97g 1.88" 832-12 V6 231.875"/105g 2.05" 834-12 2600-2800cc V6 (158-171c.i.).875"/97g 1.88" 846-8 2300cc 4 Cyl..842"/118g 2.49" Int. Harvester 855-16 V8 266-392.997"/138g 1.91" Oldsmobile 852-16 V8 260-455.842"/97g 2.05" Pontiac 864-8 151 4 Cyl..842"/98g 2.05" 852-16 V8 265-455.842"/97g 2.05" 5/16" Ball Gauge Roller Lifter Cross-Section Diameter *Pushrod Seat Height * Note: Pushrod seat heights, diameters, and weights are approximate (nominal). ** Note: All weights are for individual lifters, excluding link bars, unless otherwise noted. Part #812-16 276 WWW.CAMHELP.COM

HYDRAULIC LIFTERS Pro Magnum Hydraulic Lifters Specifically designed to perform at higher engine speeds Proper position of internal piston at higher rpm prevents lifters from harmful pumping up Significant power increase over standard hydraulic lifters Adjustable valve train required Pre-load lifters.002"-.004" with engine warm Make Part # Description Seat Ht. AMC 867-16 V8 290-401.904"/107g 1.84" 867-12 6 Cyl. 199-258.904"/107g 1.84" Buick 865-16 V8 350-455.842"/94g 2.01" 865-12 V6 183-252, 1962-Present.842"/94g 2.01" 858-16 V8 265-400.842"/99g 1.93" 858-16 V8 396-454.842"/99g 1.93" Chevrolet 858-16 V8 348-409, 1958-65.842"/99g 1.93" 858-12 6 Cyl. 194-292.842"/99g 1.93" 858-12 V6 90 200-262.842"/99g 1.93" Chrysler 867-16 V8 273-360.904"/107g 1.84" 867-16 V8 B-383-440 1968-Present.904"/107g 1.84" 862-16 V8 289-302-351W.875"/105g 1.95" 862-16 V8 351C-351M-400M.875"/105g 1.95" Ford 862-16 V8 429-460.875"/105g 1.95" 862-12 V6 231.875"/105g 1.95" 862-12 6 Cyl. 240-300.875"/105g 1.95" Oldsmobile 863-16 V8 260-455.842"/96g 2.01" Pontiac 863-16 V8 326-455.842"/96g 2.01" Horsepower Pro Magnum vs. Stock 425 400 Part #858 375 Stock Pro Magnum 350 4000 5000 RPM Engine: 468 BBC, 292H cam, 8:1 C.R., oval port heads, torker intake, 3310 carb, 12 timing, headers, stock rockers, premium unleaded gas HYDRAULIC LIFTERS Hi-Tech Hydraulic Lifters Variable Duration Lifters Greater bleed rate Increase vacuum Quicken throttle response Noisy valve train Make Part # Description Race Hydraulic Lifters Pre-load can be set between.030"-.060" Not recommended for extended periods on the street AMC 882-16 V8 290-401.904"/109g 1.91" Chevrolet 880-16 V8 265-400, 396-454, 348-409.842"/95g 1.99" Chrysler 882-16 V8 273-360, 383-440.904"/109g 1.19" Ford 884-16 V8 289-302, 351W, 429-460, 351C-400M.875"/106g 2.09" Oldsmobile 886-16 V8 260-455.842"/95g 2.05" Pontiac 886-16 V8 326-455.842"/95g 2.05" Note: For V6, use -12 suffix Best All-Around High Performance Hydraulic Flat Tappet Race Lifter Tighter plunger to body tolerances Super strict tolerances for the mechanical internals Premium one-piece pushrod seats Make Part # Description Extra heavy-duty snap ring Pre-load can be set between.000"-.030" Lubrited cam face Seat Ht. Seat Ht. Chevrolet 84000-16 Small & Big Block Race Lifters.842"/104g 2.01" Ford 84035-16 Small & Big Block Race Lifters.875"/122g 2.01" Note: For V6, use -12 suffix Part #884 Part #84000 1.800.999.0853 277

SOLID/MECHANICAL LIFTERS SOLID/MECHANICAL LIFTERS Solid/Mechanical Lifters Manufactured using tightest tolerances in the industry Crown of the lifter is ground to precise radius for proper break-in and to guarantee longer life Oil metering band is milled to correct depth to prevent too much oil from being delivered to the top of the engine New Part #813 Tool Steel Solid/Mechanical Lifters Make Part # Description Seat Ht. AMC 801-16 V8 290-401.904"/101g 1.79" Cadillac 813-16 V8 472-500.842"/98g 1.88" 813-16 V8 265-400.842"/98g 1.88" 833-16 V8 265-400 w/.875" Dia..875"/109g 1.95" Chevrolet 813-16 V8 396-454.842"/98g 1.88" 813-16 V8 348-409 1958-65.842"/98g 1.88" 813-12 V6 90 200-262.842"/98g 1.88" 813-12 6 Cyl. 194-292.842"/98g 1.88" 821-16 V8 273-360.904"/124g 1.63" 801-16 V8 273-360 (Oils Pushrod).904"/101g 1.79" Chrysler 821-16 V8 B-383-440 1958-Present.904"/124g 1.63" 821-16 V8 Hemi 426.904"/124g 1.63" 821-12 6 Cyl. 170-255.904"/124g 1.63" 831-16 V8 221-351W 1963-69.875"/108g 1.95" 833-16 V8 302-351W 1969-Present.875"/109g 1.95" 833-16 V8 Boss 302, 351C, 351M, 400M.875"/109g 1.95" 835-16 V8 352-428.875"/102g 1.79" Ford 837-16 V8 352-428 (Shell Type).875"/61g.46" 833-16 V8 429-460.875"/109g 1.95" 831-12 6 Cyl. 240-300.875"/108g 1.95" 2931-16 8 Cyl. 292-312 Y-Block Ford.498"/70g 2.6" 811FH-16 8 Cyl. 239-255 Flathead Ford 1.000"/102g Adj. Oldsmobile 835-12 6 Cyl. 144-250,V6 2600-2800cc.875"/102g 1.79" The newest addition to the COMP Cams lifter family is the line of Tool Steel Lifters, engineered from M2-grade Tool Steel for its hardness and ability to resist abrasion. Lighter weight but with the same strength as regular steel, these lifters are available in three different diameters, with each diameter available in a coated, non-coated and non-coated EDM version. The DLC (Diamond Like Carbon), multi-layer coating provides the lifters with extremely slick and hard surface properties, making them resistant to abrasive wear in extreme contact pressure environments and compatible with almost any camshaft material. This wear resistance coating also lowers the amount of power required to run an engine s valve train, as well as lowering friction, heat and oil temperatures. Extremely tough and strong, yet lighter in weight than regular steel DLC coating gives lifters slick and hard surface properties Wear resistance requires less power to run valve train and lowers friction, heat and oil temps Three diameters available in DLC coated, non-coated and non-coated EDM versions Part #89842C Part #89842 Part #89842H EDM Oiling Hole Make Part # Description Chevrolet Chrysler Ford 89842H-16 89842-16 89842C-16 89904H-16 89904-16 89904C-16 89875H-16 89875-16 89875C-16 Non-Coated for Use on Cast Cams w/ or w/o Nitriding,.012" Oil Hole Non-Coated for Use on Cast Cams w/ or w/o Nitriding Coated for Use on Cams Using Steel Cores Non-Coated for Use on Cams w/ or w/o Nitriding,.012" Oil Hole Non-Coated for Use on Cast Cams w/ or w/o Nitriding Coated for Use on Cams Using Steel Cores Non-Coated for Use on Cams w/ or w/o Nitriding,.012" Oil Hole Non-Coated for Use on Cast Cams w/ or w/o Nitriding Coated for Use on Cams Using Steel Cores Seat Ht..842"/76g 1.88".842"/76g 1.88".842"/76g 1.88".904"/84g 1.88".904"/84g 1.88".904"/84g 1.88".875"/76g 1.88".875"/76g 1.88".875"/76g 1.88" 278 WWW.COMPCAMS.COM

SOLID/MECHANICAL LIFTERS Performance Series Solid/Mechanical Lifters Built to extreme precision tolerances to create the most durable solid lifters available, the COMP Cams Performance Series Lifters are a premium lifter designed specifically for high-end street and race applications. Includes precision-ground crown radius and surface finish to promote performance camshaft compatibility and high-rpm durability Lightweight design and premium one-piece pushrod seat provide extended rpm range Features precision-machined and accurately located oil band to yield consistent, properly metered oil flow Designed for elevated, race application valve spring pressures Ideal for high-end street and race engines Make Part # Description Seat Ht. Cadillac 2900-16 V8 472-500.842"/86g 1.88" 2900-16 V8 265-400.842"/86g 1.88" 2900-16 V8 396-454.842"/86g 1.88" Chevrolet 2900-16 V8 348-409 1958-65.842"/86g 1.88" 2900-12 V6 90 200-262.842"/86g 1.88" 2900-12 6 Cyl. 194-292.842"/86g 1.88" 2921-16 V8 273-360.904"/95g 2.60" Chrysler 2921-16 V8 B-383-440 1958-Present.904"/95g 2.60" 2921-16 V8 Hemi 426.904"/95g 2.60" Ford 2910-16 V8 FS, FC, FF.875"/98g 1.95" Pontiac 2900-16 V8 260-455.842"/86g 1.88" Oldsmobile 2900-16 V8 265-455.842"/86g 1.88" Accessories 5305 Plastic Lifter Case (Holds 16) N/A N/A Part #2900 SOLID/MECHANICAL LIFTERS Performance Series Solid/Mechanical Lifters With EDM Injection Technology Our Performance Series Lifters with the EDM oiling hole have all of the same high-quality features as our Performance Series Solid/Mechanical Lifters with the addition of the EDM oiling hole on the lifter face. New AMC 2901-16 V8 290-401 w/.012" Oil Hole.904"/101g 1.79" Cadillac 800-16 V8 472-500 w/.012" Oil Hole.842"/86g 1.88" 800-16 V8 265-400 w/.012" Oil Hole.842"/86g 1.88" Chevrolet 800-16 V8 348-409 1958-65 w/.012" Oil Hole.842"/86g 1.88" 800-16 V8 396-454 w/.012" Oil Hole.842"/86g 1.88" 2901-16 A V8 273-360 w/.012" Oil Hole.904"/101g 1.79" Chrysler 2901-16 A V8 B-383-440 1958-Present w/.012" Oil Hole.904"/101g 1.79" 2901-16 A V8 Hemi 426 w/.012" Oil Hole.904"/101g 1.79" 817-16 V8 302-351W 1969-Present w/.012" Oil Hole.875"/97g 1.95" Ford 817-16 V8 Boss 302, 351C, 351M, 400M w/.012" Oil Hole.875"/97g 1.95" 817-16 V8 429-460 w/.012" Oil Hole.875"/97g 1.95" Pontiac 800-16 V8 260-455 w/.012" Oil Hole.842"/86g 1.88" Oldsmobile 800-16 V8 265-455 w/.012" Oil Hole.842"/86g 1.88" Universal 810-16 V8 Lightweight (No Chamfer) w/.012" Oil Hole.875"/79g 1.95" A. Oils through pushrods Note: For V6, use -12 suffix New Make Part # Description Seat Ht. EDM Oiling Hole Part #800 1.800.999.0853 279

HYDRAULIC ROLLER LIFTERS HYDRAULIC ROLLER LIFTERS 280 Hydraulic Roller Lifters Performance replacement for stock hydraulic roller lifters or retro-fit hydraulic roller lifters for non-roller blocks Decrease friction and increase longevity when directly compared to flat tappet lifters Accept much more aggressive cam profiles than flat tappet lifters will allow Part #853 New Short Travel Hydraulic Roller Lifters Part #851 Designed to perform at higher engine speeds When equipped with hydraulic lifters, high rpm is limited by improper position of lifter s internal piston as lifter pumps up Improper location results in open valves that lead to lost power and possibly engine failure Minimize internal movement to allow higher engine rpm Part #15853 WWW.CAMHELP.COM OE Style NO Link Bar Hydraulic Roller Lifters Chevrolet Ford 850-16 900-16 851-16 Small Block 305 and 350, Use in Blocks Originally Equipped w/ Hydraulic Roller Cam (1987-Present Including LT1 & LS Series) Big Block Gen VI and 8.1L, Use in Blocks Originally Equipped w/ Hydraulic Roller Cam (1996-Present) Small Block 302, Use in Blocks Originally Equipped w/ Hydraulic Roller Cam & in COMP Cams Ford Retro-Fit Kit for 289-302, 351W, 351C, 351M, & 400M (See page 281) Retro-Fit Link Bar Hydraulic Roller Lifters Chevrolet GM LS Chrysler Ford Olds. & Pont. 853-16 854-16 8959-16 8957-16 8920-16 8921-16 8931-16 8934-16 857-16 Small Block 265-400, Retro-Fit Roller Lifter for Early Model Blocks Originally Equipped w/ Flat Tappet Cam, Tall Body Fits Both Standard Blocks & Tall Lifter Bore Aftermarket Blocks Big Block 396-454, Retro-Fit Roller Lifter for Early Model Blocks Originally Equipped w/ Flat Tappet Cam, Tall Body Fits Both Standard Blocks & Tall Lifter Bore Aftermarket Blocks Big Block 348, 409, Retro-Fit Roller Lifter for Early Model Blocks Originally Equipped w/ Flat Tappet Cam, Tall Body Fits Both Standard Blocks & Tall Lifter Bore Aftermarket Blocks LS Series Captured Link Bar Retro-Fit Roller Lifter for 1997- Up, Fits Both Factory and RHS, LSX, Warhawk Blocks Small Block 273-360, Retro-Fit Roller Lifter for Early Model Blocks Originally Equipped w/ Flat Tappet Cam Big Block 383-440, Retro-Fit Roller Lifter for Early Model Blocks Originally Equipped w/ Flat Tappet Cam Small Block 289-302-351W, Retro-Fit Roller Lifter for Early Model Blocks Originally Equipped w/ Flat Tappet Cam Big Block & FE 390-428, 429, 460, Retro-Fit Roller Lifter for Early Model Blocks Originally Equipped w/ Flat Tappet Cam Oldsmobile & Pontiac, Retro-Fit Roller Lifter for Blocks Originally Equipped w/ Flat Tappet Cam OE Style NO Link Bar Short Travel Hydraulic Roller Lifters Chevrolet Ford 875-16 15850-16 Small Block 305 & 350, Use in Blocks Originally Equipped w/ Hydraulic Roller Cam (1987-Present Including LT1 & LS Series), Reduced Travel, OE Guide Small Block 305 & 350, Use in Blocks Originally Equipped w/ Hydraulic Roller Cam (1987-Present Including LT1 & LS Series), Short Travel, Link Bar Guide Small Block 302, Use in Blocks Originally Equipped w/ Hydraulic Roller Cam and in COMP Cams 877-16 Specially Designed Ford Retro-Fit Kit for 289-302, 351W, 351C, 351M, & 400M, Reduced Travel, OE Guide Retro-Fit Link Bar Short Travel Hydraulic Roller Lifters Small Block 265-400, Retro-Fit Roller Lifter for Early Model Blocks Originally Equipped w/ Flat Tappet Cam, 15853-16 Tall Body Fits Both Standard Blocks & Tall Lifter Bore Aftermarket Blocks, Short Travel, Link Bar Guide Chevrolet GM LS Part # Part # 15854-16 15956-16 Description Description Big Block 396-454, Retro-Fit Roller Lifter For Early Model Blocks Originally Equipped w/ Flat Tappet Cam, Tall Body Fits Both Standard Blocks & Tall Lifter Bore Aftermarket Blocks, Short Travel, Link Bar Guide LS Series Captured Link Bar Retro-Fit Roller Lifter for 1997-Present, Fits Both Factory & RHS, LSX, Warhawk Blocks, Short Travel, Link Bar Guide.842"/122g 2.66".842"/121g 2.66".875"/135g 2.60".842"/136g 2.49".842"/137g 2.49".842"/136g 2.49".842"/140g 2.42".904"/141g 4.57".904"/159g 2.63".875"/146g 2.60".875"/147g 2.60".842"/136g 2.49" Seat Ht. Seat Ht..842"/122g 2.60".842"/132g 2.66".875"/128g 2.60".842"/152g 2.66".842"/150g 2.66".842"/145g 2.66"

HYDRAULIC ROLLER KITS Hydraulic Roller Lifter Installation Kits COMP Cams has put together these time saving kits containing all of the necessary pieces to help you smoothly install hydraulic roller lifters in your V6 or V8 block originally equipped with a hydraulic roller cam. Each kit contains all required hardware and each piece is new. Part #08-1000 Make Part # Application Kit Contains: Chevrolet 08-1000 08-1001 09-1000 Chevy Small Block 1987-93 Non-Vortec V8 305 & 350 w/ OE Hyd. Roller Cam Chevy Small Block 1991-02 Vortec Engines, 1991-97 LT1 Chevy V6 4.3L w/ Balance Shaft (Except 1994-Present w/ Plastic Lifter Guides) Chevy V6 4.3L w/o 09-1001 A Balance Shaft (Except 1985-86 w/ Hyd. Roller Cam) Ford 35-1001 Ford 302 HO, 5.0 A. Lifter retainer not available for this engine (3) #4605-B Camshaft Bolts (8) #8105-LG Lifter Guides (1) #8105-LR Lifter Retainer (1) #8105-CR Cam Retainer (2) #8105-B Cam Retainer Bolts (3) #4605-B Camshaft Bolts (8) #8105-LG Lifter Guides (1) #8105-LR Lifter Retainer (1) #8104-CR Cam Retainer (2) #8105-B Cam Retainer Bolts (3) #4605-B Camshaft Bolts (6) #8105-LG Lifter Guides (1) #8106-LR Lifter Retainer (1) #8106-CR Cam Retainer (2) #8106-B Cam Retainer Bolts (6) #8105-LG Lifter Guides (1) #8105-CR Cam Retainer (2) #8105-B Cam Retainer Bolts (8) #8135-LG Lifter Guides (1) #8135-LR Lifter Retainer (2) #8135-B Cam Retainer Bolts HYDRAULIC ROLLER KITS Ford Hydraulic Roller Retro-Fit Kit This Ford Hydraulic Roller Retro-Fit Kit contains the pieces required to install our complete line of hydraulic roller cams in 302, 351W, 351C and 351M-400 Ford engines that did not come with an OEM hydraulic roller cam. This kit ships complete with detailed instructions and all necessary hardware. Works on all Small Block Ford engines originally equipped with a flat tappet or roller cam When using this kit in a non-roller block, a small base circle retro-fit cam must be used to ensure the lifters will not expose oil hole or band out of the lifter bores Kit must be used with Part #851-16 and Part #877-16 lifters Make Part # Application Kit Contains: (8) #8135-LG Lifter Guides Small Block 289-302, Ford 31-1000 (1) #8135-LR Lifter Retainer 351W, 351C, 351M-400M (2) #8135-CS Cap Screws Part #31-1000 1.800.999.0853 281

Endure-X Solid Roller Lifters Today s engines place a greater demand on lifters than ever before. With today s more aggressive cam lobe designs and increased rpm ranges, it takes a superior roller lifter to withstand the abuse. COMP Cams has set the industry standard with the Endure-X Solid Roller Lifters. Endure-X Lifters are fully heat-treated, machined to ultra-high tolerances, are fully rebuildable and are available for a wide variety of applications, including small base circle and offset applications. A complete application listing is on the following pages 283 through 285 of this catalog. The four main features of Endure-X Solid Roller Lifters are: 1. Removable Link Bar COMP Cams patented link bar assembly combines the benefits of a removable link bar with the safety of a captured link bar. 2. EDM Oil Injection Technology Guarantees that the bearing assembly receives a constant flow of pressurized oil via a precision hole aimed directly at the needle bearings. 3. Precision Sorted Bearings The needle bearings are precision sorted by size to distribute load evenly, preventing premature wear and failure. 2 EDM Oil Injection Technology 1 Removable Link Bar 4. Tool Steel Axle The axle is made of wear resistant Tool Steel to prolong the life of the roller assembly, particularly in high rpm applications. 4 Tool Steel Axle Endure-X Solid Roller Lifter Rebuild Program Today s roller lifters face grueling engine environments. Inadequate oiling, excessive spring pressures and valve lash, along with other factors, play a significant part in the failure of the roller, needle bearings and axle. COMP Cams recognizes the high cost of new parts and designed the Endure-X Lifter Rebuild Program to help offset some of that cost. 3 Precision Sorted Bearing The roller assembly is often the culprit in roller lifter failure. The lifter body can be buffed and the link bars replaced as necessary. However, the roller bearings and axle usually need to be replaced after each season of use or after any catastrophic engine failure. A sudden lack of motion is even more destructive than the sudden application of motion. There is a small fee to replace worn or damaged parts, and replacement lifters may be purchased to replace defective or destroyed ones. This is often less than half of the cost of new lifters and ensures long, trouble free operation. Rebuilt solid roller lifters go through the following steps: 1. Lifter bodies are disassembled and inspected for cracks. 2. Retaining grooves are inspected and cleaned. 3. Lifter bodies are thoroughly washed. 4. A new axle and roller assembly are pressed into the body, and new retaining clips are installed. 5. Lifters are reboxed and returned to the customer. Part #818 Part # 800-RB1-1 800-RB2-1 Description For.750" Wheel Diameter For.850" Wheel Diameter 282 WWW.COMPCAMS.COM

STYLE A: Cutaway Oil Band STYLE C: Cutaway Solid Lifter Body Styles STYLE B: Solid Oil Band STYLE D: Solid American Motors V8 290-401 1966-89 861-16 Baseline Coverage for All Types of Motorsports Using the AMC Engine Buick V6 868-12 Best for Any Application When a Centered Pushrod Style B Can Be Used New Part #/ Style 868S-12 For Engines that Oil Through Rocker Arm Shafts, Style B Not Through Pushrods Chevrolet 90º V6 (Race) 818-12 Best All Around Set When a Centered Pushrod Can Style B Be Used 897-12 Use When an Offset Intake Pushrod Set Is Required for Clearance, Centered Exhaust Determining Offset Left Offset Right Offset Note: On offset lifters, offset is determined by looking at the lifter with the link bar away from you.904"/136g (16) 861-1 (8) 839-L All Centered Parallel 1.91".842"/119g (12) 818-1.842"/110g (12) 868S-1 (5) 818-L (1) 814-L (5) 818-L (1) 814-L All Centered All Centered N/A 1.30".842"/119g (12) 818-1 (6) 818-L All Centered.842"/114g (6) 894C-1 (2) 894R-1 (4) 894L-1 (4) 818-L (2) 814-L (6) Centered (2) Rights (4) Lefts Chevrolet V8 265-400 (*Denotes Tappets For 1987-Current, Bowtie & Some Aftermarket Blocks w/ Taller Lifter Bores) 815-16 Style B Great for Any Application w/ Enlarged Lifter Bores, Ford Diameter.875"/127g (16) 815-1 (8) 818-L All Centered 818-16 Style B Perfect Roller Lifter for Any Application w/ No Offsets.842"/119g (16) 818-1 (8) 818-L All Centered 847-16 Offset Intakes w/ Special Captured Link Bar Design.842"/111g (4) Pr. 847LC-2 (4) Pr. 847RC-2 Captured (4) Rights (4) Lefts 871-16 Style B Full Body Style of #873-16.300" Taller Body for 1987 & Up, Bowtie & Most Aluminum Blocks.842"/138g (16) 871-1 (8) 818-L All Centered 873-16.300" Taller Body for 1987 & Up, Bowtie & Most Aluminum Blocks.842"/117g (16) 873-1 (8) 818-L All Centered 888-16.300" Taller Body Lifters Designed for Street & Marine Applications.842"/116g (16) 888-1 (8) 818-L All Centered 890-16 891-16 Style B 894-16 896-16 8995-16 Description.300" Taller Body Lifters w/ Offset Intakes for Additional Clearance & Enlarged Lifter Bores Specifically Engineered for Any Application Using Small Base Circle Cams A Proven Winner When Offset Intakes are Necessary for More Pushrod Clearance For Use w/ Dart, Buick, Canted or Splayed Valve Heads, Left Offset Intakes.875"/136g (8) 890C-1 (4) 890R-1 (4) 890L-1 (8) 818-L (4) Rights (4) Lefts Perpendicular 1.91".842"/122g (16) 891-1 (8) 818-L All Centered.842"/114g.842"/114g.300" Taller Offset Lifters.842"/117g Chevrolet V8 SB2 8991-16 SB2 Block, SB2 Head.300" Tall Lifters w/.874" Lifter Bore, Centered Pushrod Seats 8992-16 Standard GM Block, SB2 Head.300" Tall Offset.842" Lifter Bore, Offset Pushrod Seat 8993-16 Standard GM Block, SB2 Head.300" Tall Offset.875" Lifter Bore, Offset Pushrod Seat Set Includes Wt. Lifters Link Bars (8) 894C-1 (4) 894R-1 (4) 894L-1 (8) 894C-1 (8) 894L-1 (8) 873-1 (4) 873R-1 (4) 873L-1.875"/122g (16) 890C-1.842"/114g.875"/122g (8) 894L-1 (8) 894R-1 (8) 890L-1 (8) 890R-1 (8) 818-L (8) 818-L (8) 818-L (4) 0894-L (4) 0895-L (8) 818-L (8) 818-L Pushrod Seat Location (4) Rights (4) Lefts (8) Lefts (4) Rights (4) Lefts (16) Centered (8) Lefts (8) Rights (8) Lefts (8) Rights Oil Hole vs. Axle Seat Ht. 1.800.999.0853 283

GM Gen III/LS1/LS2/LS6/LS7/LSX 8956-16 GM Gen III/LS1/LS2/LS6 Solid Roller Lifters Not Designed for Street Use.842"/118g (16) 8956-1 (8) 838-L (16) Centered Perpendicular 2.01" 8958-16 GM Solid Roller Lifters for LSX/Warhawk Block.842"/118g (16) 8956-1 (8) 8958-L (16) Centered Perpendicular 2.01" Chevrolet V8 396-454 1965-96 819-16 Style B Perfect for Any Application w/ No Offsets.842"/118g (16) 819-1 (8) 819-L All Centered New New Part #/ Style 823-16 Style B 866-16 883-16 893-16 Style B 895-16 897-16 898-16 899-16 8996-16 Great for Any Application w/ Enlarged Lifter Bores, Ford Diameter.300" Taller Body Designed for Street & Marine Applications.300" Taller Body for Late Model, Bowtie & Most Aluminum Blocks Specifically Engineered for Any Application Using Small Base Circle Cams Most Durable Set When Right Offsets Are Necessary for More Pushrod Clearance Best When Cutaway Style Lifter Bodies Are Necessary for Improved Clearance Best Available Lifters When Left Offsets Are Necessary for More Pushrod Clearance Proven Winner When Offset Intakes Are Necessary for More Pushrod Clearance.300" Taller Cutaway Offset Lifters for Any Application w/ Extreme Pushrod Angles.875"/127g (16) 815-1 (8) 819-L All Centered.842"/116g (16) 888-1 (8) 873-L All Centered.842"/117g (16) 873-1 (8) 873-L All Centered.842"/122g (16) 891-1 (8) 819-L All Centered.842"/114g (8) 894C-1 (8) 894R-1 (8) 819-L (8) Rights.842"/114g (16) 894C-1 (8) 819-L All Centered.842"/ 114g.842"/ 114g.842"/117g (8) 894C-1 (8) 894L-1 (8) 894C-1 (4) 894R-1 (4) 894L-1 (8) 873-1 (4) 873R-1 (4) 873L-1 (8) 819-L (8) 819-L (8) 819-L (8) Lefts (4) Rights (4) Lefts (4) Rights (4) Lefts Chrysler V8 273-360 828-16 Style C Best All Around Lifter for Engines That Oil Through Rocker Shafts, No Oil Hole.904"/125g (8) 828-2 Captured All Centered N/A 1.79" 8043-16 Solid Roller Lifters w/ Oiling And Inboard Link Bars.904"/132g (8) 8043-2 Captured All Centered Parallel 1.93" Chrysler V8 383-440 AND 426 Hemi Note: Fat Head Spread Lifter Bore Requires Special Ordering (8) Link Bars #839-L 827-16 Style C Pushrod Seat Is Located.225" Deeper Than Standard Location.904"/124g (16) 827-1 (8) 829-L All Centered N/A 1.57" 829-16 Style C Standard Pushrod Seat Location, Best for Performance Street & Drag Racing.904"/127g (16) 829-1 (8) 829-L All Centered N/A 1.79" 830-16 Style C Pushrod Seat Is Located.140" Deeper Than Standard Location.904"/122g (16) 830-1 (8) 829-L All Centered N/A 1.65" 830A-16 Style C 87019-16 Description Pushrod Seat Is Located.165" Deeper Than Standard Location.300" Tall Offset Lifters for Engines That Oil Through Rocker Shafts, No Oil Hole Set Includes Wt. Lifters Link Bars.904"/128g (16) 830A-1 (8) 829-L All Centered N/A 1.63".904"/135g Pushrod Seat Location (8) 87016C-1 (4) 87018R-1 (8) 829-L (4) Rights (4) 87017L-1 (4) Lefts Oil Hole vs. Axle N/A 1.91" Ford V8 289-351W Note: 289 & 302 Require Cylinder Head Removal To Install Lifters 838-16 Best All Around Lifter Available, Perfect for Any Style B Application w/ No Offets.875"/134g (16) 838-1 (8) 838-L All Centered Perpendicular 2.01" Ford V8 SVO Small Block Drag Race Applications w/ Yates Heads 87879-16 Lifter Designed for Drag Race Applications Using Yates Heads.875"/236g* (8) 87879-2 Captured (8) Rights.180" Parallel 2.05" Ford V8 351C, 351M, 400M Note: With 5/16" Pushrods Only 840-16 Perfect Lifter for Cleveland Applications w/ No Style B Offsets Necessary.875"/134g (16) 836-1 (8) 838-L All Centered Parallel 2.01" Ford V8 352-428 839-16 The Best FE Mechanical Roller Available, Works in Style B Any High Performance Application.875"/134g (16) 838-1 (8) 839-L All Centered Perpendicular 2.01" * Denotes weight of a set of lifters, including (2) lifters and a link bar. Seat Ht. 284 WWW.CAMHELP.COM

Part #/ Style Ford V8 429-460 836-16 Our Most Durable Lifter Set, Fits Most Combinations in Any Style B Application 841-16 Description The Same Durable Design Incorporated w/ a Unique Captured Link Bar System, for Most Hemi Type Fords 879-16 Special Arranged Set Featuring a Captured Link Bar Design w/ an Offset Intake Holden V8 881-16 The Best & Only Set Available for the Holden, Works in Any Application Oldsmobile V8 350-455 849-16 The Perfect Lifter for Street, Drag & Marine When Style B No Offset is Necessary Pontiac V8 350-455 859-16 The Best Choice for All Engine Sizes in Any Application, Especially Performance Street Set Includes Wt. Lifters Link Bars.875"/134g (16) 836-1 (8) 836-L All Centered Parallel 2.01".875"/108g (8) 841-2 Captured All Centered Parallel 2.01".875"/112g (8) 879-2 Captured Pushrod Seat Location (8) Rights.180" Oil Hole vs. Axle Seat Ht. Parallel 2.01".842"/120g (16) 881-1 (8) 829-L All Centered Parallel 2.01".842"/120g (16) 859-1 (8) 829-L All Centered Parallel 2.01".842"/120g (16) 859-1 (8) 829-L All Centered Parallel 2.01" Part #894 Endure-X Single Solid Roller Lifters Part #/ Style Description Wt. Pushrod Seat Location Offset Distance Oil Hole vs. Axle Wheel Diameter 890C-1.300" Tall Roller Lifter.875"/122g Centered 0 Perpendicular.750" 1.88" 890L-1.300" Tall Roller Lifter.875"/122g Left.180" Perpendicular.750" 1.88" 890R-1.300" Tall Roller Lifter.875"/122g Right.180" Perpendicular.750" 1.88" 892C-1.300" Tall Roller Lifter.904"/133g Centered 0 Perpendicular.800" 1.91" 892L-1.300" Tall Roller Lifter.904"/133g Left.210" Perpendicular.800" 1.91" 892R-1.300" Tall Roller Lifter.904"/133g Right.210" Perpendicular.800" 1.91" 894C-1 Roller Lifter.842"/114g Centered 0 Perpendicular.750" 1.88" 894L-1 Roller Lifter.842"/114g Left.180" Perpendicular.750" 1.88" 894R-1 Roller Lifter.842"/114g Right.180" Perpendicular.750" 1.88" 873-1.300" Tall Roller Lifter.842"/117g Centered 0 Perpendicular.750" 1.88" 873L-1.300" Tall Roller Lifter.842"/117g Left.180" Perpendicular.750" 1.88" 873R-1.300" Tall Roller Lifter.842"/117g Right.180" Perpendicular.750" 1.88" 87016C-1.300" Tall Roller Lifter w/o Oil Hole.904"/135g Centered.210" N/A.800" 1.91" 87017L-1.300" Tall Roller Lifter w/o Oil Hole.904"/135g Left.210" N/A.800" 1.91" 87018R-1.300" Tall Roller Lifter w/o Oil Hole.904"/135g Right.210" N/A.800" 1.91" Note: Individual pieces only, not sets. Link bars must be ordered separately. See p. 286 for link bars. Seat Ht. 1.800.999.0853 285

Roller Lifter Link Bars COMP Cams Roller Lifter Link Bars are precision-crafted from stainless steel and wear-coated for a long life in all applications. Part # Description Lifter Bore C/L A B C Style Chevrolet Small Block 1.560" 818-L Chevrolet V6 Cylinders #1, #2, #5 & #6 1.560" 1.350" 2.380" 2.000" Flat Buick V6 Cylinders #1, #2, #4, #5 & #6 1.525" 814-L Chevrolet V6 Cylinders #3 & #4 1.660" Buick V6 Cylinder #3 1.610" 1.475" 2.500" 2.125" Flat 838-L GM GenIII/LS1/LS2/LS6 1.730" Ford Small Block 289-302, 351W, SVO 351 1.730" 1.564" 2.594" 2.214" Flat 8958-L GM LS for LSX/Warhawk/RHS /Factory Block 1.827" 1.500" 2.470" 2.340" 836-L Ford Big Block 429-460 2.075" 2.019" 3.044" 2.669" Flat Chrysler 426-440 1.800" 829-L Pontiac 350-455 1.818" 1.654" 2.680" 2.295" Flat Oldsmobile 350-455 1.877" AMC 360-401 1.940" 839-L F.E. Style Ford 392-428 1.980" 1.884" 2.910" 2.534" Flat Chrysler "Fat Head" 2.000" 819-L Chevrolet Big Block 396-454 1.800" 1.560" 2.610" 2.250" 873-L Chevrolet Big Block 396-454 for.300" Tall Lifters 1.800" 1.560" 2.610" 2.250" 0894-L GM SB2 Cylinders #1 & #3 1.835" 1.614" 2.679" 2.304" 0895-L GM SB2 Cylinders #2 & #4 1.834" 1.614" 2.679" 2.304" 0895-L GM SB2 Cylinders #5 & #7 1.812" 1.614" 2.679" 2.304" 0894-L GM SB2 Cylinders #6 & #8 1.813" 1.614" 2.679" 2.304" Note: Dimensions are listed for popular applications New Part #8958-L Part #818-L Part #819-L 286 WWW.COMPCAMS.COM

New Elite Race Solid Roller Lifters If you re looking for the ultimate lifter to withstand even the most demanding racing conditions, look no further. The COMP Cams Elite Race Solid Roller Lifters feature a host of advantages over competing race lifter designs, including an REM polished 8620 alloy body that is CNC-machined, SAE 9310 steel alloy wheels that are micro-polished and micro-sized and needles that are made from 52100 bearing steel and micro-sorted with a controlled contour profile. These lifters feature an exclusive body design that does not include an oil band, maximizing rigidity and reducing lifter bushing wear. While the construction and body design make them incredibly strong, the Elite Race Solid Roller Lifters are also lightweight, with each lifter weighing approximately 100 grams individually. All lifter bodies are tall and will clear both stock and aftermarket.300" tall lifter bores and will properly fit either 5/16" or 3/8" ball pushrods. Possibly the most critical element of this lifter design is the fact that the oversized (.400") axles are dual-pinned pins go through the lifter ears at each end and leave a small gap in between for oiling. And with this pressure fed oiling you get wear-reducing engine lubrication when and where you need it the most. The oil actually flows through the center and the top of the axle directly to the needles. For maximum control and durability in high rpm race applications, these lifters also feature captured link bars and an exclusive modular pushrod design that allows the pushrod insert to be swapped out for centered, left or right offsets. And with our patent-pending oil control through the pushrod insert, engine builders can modify the lifter to meter extra oil to the top as desired. Elite Race Solid Roller Lifters are fully heat-treated, machined to high tolerances, are fully rebuildable and are available for a number of Chevy, Ford and Chrysler applications. A complete application listing is on the following pages but look for new applications at www.compcams.com. Elite Race Solid Roller Lifter Oiling Path Pressurized Oil 1. Modular Design Pushrod insert can be changed for centered, left or right offsets. A patent-pending design allowing oil control through the pushrod insert lets builders modify lifters to meter extra oil to the top. 2. Tool Steel, Dual-Pinned Axles.400" Axles (extra large for maximum load support) allow for extra needle bearings (total of 23) for optimum load distribution. Needles are constructed from 52100 bearing steel and are micro-sorted with a controlled contoured profile. Dual-pinned axles are pinned through the lifter ears on both sides to allow oiling between them, whereas competitors lifters only use a single pin. 3. Pressure-Fed Oiling Center and top axle oil inlets for lubrication through the axle, directly to the needles exactly where you need it. 4. Captured Link Bars Designed specifically for race and high rpm applications, captured link bars offer maximum control and durability. 1.800.999.0853 287

Elite Race Solid Roller Lifters Lightweight Arm Design for Reduced Mass Interchangeable Pushrod Seats (Offsets Available) - COMP Exclusive Oil Metering Circuit Through Insert Easily Modified to Customize Oil Flow COMP Exclusive Column Design for Strength, Reduced Sidewear, Lifter Bore Stability & Reduced Mass 9310 Steel, Precision Ground & Polished Wheels Micro-Sorted Precision Ground Needle Bearings Captured Link Bars for Maximum Stability at High RPM Precision CNC-Machined Hollow Axle (Pressurized Oiling Feed Circuit & Reduced Mass) COMP Exclusive Dual Pinned Axle for Interlocking Body & Axle, Maintains Stability Under Extreme Loads CNC-Machined & Ground, REM Polished 8620 Steel Body, Fits Both Standard &.300" Tall Blocks Increased Surface for Support & Less Lifter Bore Wear EDM Oiling Hole for Pressurized Oiling Through Hollow Axle Directly to Needle Bearings.400" Diameter Oversized Axle for Ultimate Load Capacity & Longevity (Largest in Industry) 288 WWW.CAMHELP.COM

Part # Description Wt. Small Block Chevrolet V8 265-400 A Set Includes: Lifters Pushrod Seat Location Wheel Diameter Seat Ht. 98818-16 Roller Lifters.842"/99g (8) 98842C-2 8 Pairs Centered.750" 1.91" 98894-16.160" Offset Roller Lifters.842"/99g 98815-16 98890-16 98891-16 98892-16 98893-16 Roller Lifters for Applications w/ Enlarged Lifter Bores (.875").160" Offset Roller Lifters for Applications w/ Enlarged Lifter Bores (.875") Roller Lifters for Applications w/ Enlarged Lifter Bores (.904").180" Offset Roller Lifters for Applications w/ Enlarged Lifter Bores (.904").180" Offset Roller Lifters for Applications w/ Enlarged Lifter Bores (.904") Big Block Chevrolet V8 396-454 B (4) 98842CL-2 (4) 98842CR-2 4 Pairs Centered & Left 4 Pairs Centered & Right.750" 1.91".875"/102g (8) 98874C-2 8 Pairs Centered.750" 1.93".875"/102g (4) 98874CL-2 (4) 98874CR-2 4 Pairs Centered & Left 4 Pairs Centered & Right.785" 1.93".904"/102g (8) 98904C-2 8 Pairs Centered.785" 1.95".904"/102g (4) 98904CL-2 (4) 98904CR-2 4 Pairs Centered & Left 4 Pairs Centered & Right.820" 1.95".904"/102g (8) 98904LR-2 8 Pairs Left & Right.820" 1.95" 98819-16 Roller Lifters.842"/99g (8) 98852C-2 8 Pairs Centered.750" 1.91" 98996-16.160" Offset Roller Lifters.842"/99g 98823-16 98997-16 98995-16 98998-16 98999-16 LS Series, GM Gen III/IV C Roller Lifters for Applications w/ Enlarged Lifter Bores (.875").160" Offset Roller Lifters for Applications w/ Enlarged Lifter Bores (.875") Roller Lifters for Applications w/ Enlarged Lifter Bores (.904").180" Offset Roller Lifters for Applications w/ Enlarged Lifter Bores (.904").180" Offset Roller Lifters for Applications w/ Enlarged Lifter Bores (.904") (4) 98852CL-2 (4) 98852CR-2 4 Pairs Centered & Left 4 Pairs Centered & Right.750" 1.91".875"/102g (8) 98851C-2 8 Pairs Centered.750" 1.93".875"/102g (4) 98851CL-2 (4) 98851CR-2 4 Pairs Centered & Left 4 Pairs Centered & Right.785" 1.95".904"/102g (8) 98850C-2 8 Pairs Centered.820" 1.95".904"/102g (4) 98850CL-2 (4) 98850CR-2 4 Pairs Centered & Left 4 Pairs Centered & Right.820" 1.95".904"/102g (8) 98850LR-2 8 Pairs Left & Right.820" 1.95" 98956-16 Roller Lifters.842"/99g (8) 98956C-2 8 Pairs Centered.750" 1.91" 98954-16 98952-16 Chrysler V8 383-440 D Roller Lifters for Applications w/ Enlarged Lifter Bores (.875") Roller Lifters for Applications w/ Enlarged Lifter Bores (.904").875"/102g (8) 98954C-2 8 Pairs Centered.785" 1.93".904"/102g (8) 98952C-2 8 Pairs Centered.820" 1.95" 98829-16 Roller Lifters.904"/102g (8) 98829C-2 8 Pairs Centered.820" 1.95" 98827-16.180" Offset Roller Lifters.904"/102g (4) 98829CL-2 (4) 98829CR-2 4 Pairs Centered & Left 4 Pairs Centered & Right.820" 1.95" Ford V8 289-351W C 98838-16 Roller Lifters.875"102g (8) 98838C-2 8 Pairs Centered.785" 1.93" 98837-16.160" Offset Roller Lifters.875"/102g (8) 98838CR-2 8 Pairs Centered & Right.785" 1.93" 98835-16.180" Offset Roller Lifters for Applications w/ Enlarged Lifter Bores (.904") Ford V8 352-428 & 429-460 D.904"/102g (8) 98835CR-2 8 Pairs Centered & Right.820" 1.95" 98836-16 Roller Lifters.875"/102g (8) 98836C-2 8 Pairs Centered.785" 1.93" 98839-16 Roller Lifters for Applications w/ Enlarged Lifter Bores (.904").904"/102g (8) 98839C-2 8 Pairs Centered.820" 1.95" A. Lifter bore spacing min. 1.435 & max. @.450" lift is 1.700/@.500" lift is 1.670 B. Lifter bore spacing min. 1.765 & max. @.450" lift is 2.040/@.500" lift is 2.020 C. Lifter bore spacing min. 1.700 & max. @.450" lift is 1.975/@.500" lift is 1.950 D. Lifter bore spacing min. 1.840 & max. @.450" lift is 2.120/@.500" lift is 2 The footnotes list the min. allowable lifter bore spacing for each of the given Elite Race link bars, along with the max. allowable spacing for.450" &.550" lift lobe applications. With internal oiling, the Elite Race design can be used in many non-listed applications, and this spacing info. can be used to select the correct configuration. 1.800.999.0853 289

Elite Race Individual Pair Captured Link Bar Lifter Part Numbers Part # Description Wt. Small Block Chevrolet V8 265-400 Pushrod Seat Location Offset Distance Wheel Diameter 98842C-2 Roller Lifter Pair Both Centered.842"/99g Both Centered 0.750" 1.91" 98842CL-2 98842CR-2 98842LR-2 98874C-2 98874CL-2 98874CR-2 98874LR-2 98904C-2 98904CL-2 98904CR-2 98904LR-2 Offset Left Offset Right Roller Lifter Pair One Offset Left & One Offset Right Roller Lifter Pair Both Centered For Enlarged Lifter Bores (.875") Offset Left For Enlarged Lifter Bores (.875") Offset Right For Enlarged Lifter Bores (.875") Roller Lifter Pair One Offset Left & One Offset Right For Enlarged Lifter Bores (.875") Roller Lifter Pair Both Centered For Enlarged Lifter Bores (.904") Offset Left For Enlarged Lifter Bores (.904") Offset Right For Enlarged Lifter Bores (.904") Roller Lifter Pair One Offset Left & One Offset Right For Enlarged Lifter Bores (.904") Big Block Chevrolet V8 396-454 1965-1996 Seat Ht..842"/99g Centered & Left 0,.160".750" 1.91".842"/99g Centered & Right 0,.160".750" 1.91".842"/99g Left & Right.160",.160".750" 1.91".875"/102g Both Centered 0.785" 1.93".875"/102g Centered & Left 0,.160".785" 1.93".875"/102g Centered & Right 0,.160".785" 1.93".875"/102g Left & Right.160",.160".785" 1.93".904"/102g Both Centered 0.820" 1.95".904"/102g Centered & Left 0,.180".820" 1.95".904"/102g Centered & Right 0,.180".820" 1.95".904"/102g Left & Right 0,.180".820" 1.95" 98852C-2 Roller Lifter Pair Both Centered.842"/99g Both Centered 0.750" 1.91" 98852CL-2 98852CR-2 98852LR-2 98851C-2 98851CL-2 98851CR-2 98851LR-2 98850C-2 98850CL-2 98850CR-2 98850LR-2 Roller Lifter Pair One Centered & One Offset Left Offset Right Roller Lifter Pair One Offset Left & One Offset Right Roller Lifter Pair For Enlarged Lifter Bores (.875") Roller Lifter Pair One Centered & One Offset Left - For Enlarged Lifter Bores (.875") Offset Right - For Enlarged Lifter Bores (.875") Roller Lifter Pair One Offset Left & One Offset Right - For Enlarged Lifter Bores (.875") Roller Lifter Pair Both Centered For Enlarged Lifter Bores (.904") Offset Left For Enlarged Lifter Bores (.904") Offset Right For Enlarged Lifter Bores (.904") Roller Lifter Pair One Offset Left & One Offset Right For Enlarged Lifter Bores (.904").842"/99g Centered & Left 0,.160".750" 1.91".842"/99g Centered & Right 0,.160".750" 1.91".842"/99g Left & Right.160",.160".750" 1.91".875"/102g Both Centered 0.785" 1.93".875"/102g Centered & Left 0,.160".785" 1.93".875"/102g Centered & Right 0,.160".785" 1.93".875"/102g Left & Right.160",.160".785" 1.93".904"/102g Both Centered 0.820" 1.95".904"/102g Centered & Left 0,.180".820" 1.95".904"/102g Centered & Right 0,.180".820" 1.95".904"/102g Left & Right.180",.180".820" 1.95" 290 WWW.COMPCAMS.COM

Elite Race Individual Pair Captured Link Bar Lifter Part Numbers Cont. Part # Description Wt. Pushrod Seat Location Offset Distance Wheel Diameter LS Series, GM Gen III/IV 98956C-2 Roller Lifter Pair Both Centered.842"/99g Both Centered 0.750" 1.91" 98954C-2 Roller Lifter Both Centered for Enlarged Lifer Bores (.875").875"/102g Both Centered 0.785" 1.93" 98952C-2 Roller Lifter Both Centered for Enlarged Lifer Bores (.904").904"/102g Both Centered 0.820" 1.95" Chrysler V8 383-440 98829C-2 Roller Lifter Pair Both Centered.904"/102g Both Centered 0.820" 1.95" 98829CL-2 Offset Left.904"/102g Centered & Left 0,.180".820" 1.95" 98829CR-2 Offset Right.904"/102g Centered & Right 0,.180".820" 1.95" Ford V8 289-351W 98838C-2 Roller Lifter Pair Both Centered.875"/102g Both Centered 0.785" 1.93" 98838CL-2 98838CR-2 98835C-2 98835CL-2 98835CR-2 Ford V8 352-428 & 429-460 Offset Left Offset Right Roller Lifter Pair Both Centered For Enlarged Lifter Bores (.904") Offset Left For Enlarged Lifter Bores (.904") Offset Right For Enlarged Lifter Bores (.904") Seat Ht..875"/102g Centered & Left 0,.160".785" 1.93".875"/102g Centered & Right 0,.160".785" 1.93".904"/102g Both Centered 0.820" 1.95".904"/102g Centered & Left 0,.180".820" 1.95".904"/102g Centered & Right 0,.180".820" 1.95" 98836C-2 Roller Lifter Pair Both Centered.875"/102g Both Centered 0.785" 1.93" 98836CL-2 98836CR-2 98839C-2 98839CL-2 98839CR-2 Offset Left Offset Right Roller Lifter Pair Both Centered For Enlarged Lifter Bores (.904") Offset Left For Enlarged Lifter Bores (.904") Offset Right For Enlarged Lifter Bores (.904").875"/102g Centered & Left 0,.160".785" 1.93".875"/102g Centered & Right 0,.160".785" 1.93".904"/102g Both Centered 0.820" 1.95".904"/102g Centered & Left 0,.180".820" 1.95".904"/102g Centered & Right 0,.180".820" 1.95" Pushrod Seat Inserts With the new Elite Race Solid Roller Lifters, COMP Cams has made it possible to remove the pushrod seat inserts and swap them out. Offered in centered, left offset and and right offset options for each diameter lifter, the pushrod seats can be switched out and any combination of seats can be used. With our Pushrod Seat Insert Removal Tool, this is a simple process that allows the user to easily adjust the pushrod angle for clearance if necessary. Part # Description Dia. Pushrod Seat Location 98500C-1 Centered Pushrod Seat Insert.842"/.875" Centered 98500L-1 Left Offset Pushrod Seat Insert.842"/.875".160" Left 98500R-1 Right Offset Pushrod Seat Insert.842"/.875".160" Right 98600C-1 Centered Pushrod Seat Insert.904" Centered 98600L-1 Left Offset Pushrod Seat Insert.904".180" Left 98600R-1 Right Offset Pushrod Seat Insert.904".180" Right 98501-1 O-Ring.842"/.875" N/A 98601-1 O-Ring.904" N/A 5350 Pushrod Seat Insert Removal Tool N/A N/A 1.800.999.0853 291