SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.ssvworks.com Phone: 818-991-1778 Fax: 866-293-6751 Yamaha YXZ 1000 R Behind Seat 10 Subwoofer Enclosure WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.! Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle. TOOLS NEEDED FOR INSTALLATION PARTS LIST - 10mm and 12mm Socket and Ratchet - 4mm Allen Key - Panel Removal Tool - 1/4 drill bit - #3 Phillips Screw Driver - Air Saw or High Speed Cutting Tool Enclosure x1 M6x0 Screws x 16 M6 Washer x17 4. M6 Lock Nut x 1 5. Top Mounting Bracket 6. Side Mounting Bracket 7. T-Bracket 8. Cut Template PARTS LIST IMAGES Enclosure x 1 M6 x 0 Screws x 16 M6 Washers x 17 4. M6 Nuts x 1 5. Top Mounting Bracket 6. Side Mounting Bracket 7. T-Bracket 8. Template x 1 INSTALLATION NOTES The use of a thread locker is recommended on all screws to prevent loosening due to vibration.
Removing the Passenger Seat Lift the front of the seat pan to release it from the retaining clip securing it down. Using a 12mm socket or wrench remove the (4) bolts securing the base of passenger seat. Lift the passenger seat up and away. A The center console is split into two pieces, a battery cover and dash cover. The battery cover is secured by 2 panel snaps at the rear of the panel. To remove the battery cover simply lift in an upward direction to release it from the 2 panel snaps securing it down. B To remove the dash cover you will need to extract the panel snap that is exposed after removing the battery cover. C Next remove the hood and extract (2) 10mm bolts securing the top of the dash cover. D Remove the dash by lifting up and away. E
F Remove the Center Console Passenger Side Panel The passenger side panel is secured by 5 panel snaps & 3 bolts Remove all panel snaps using a panel removal tool Extract the 3 bolts along the lower perimeter of the panel & remove G Removed Center Console Passenger Side Panel I H Remove Passenger Quarter Panel Fairing / Body Panel Removing the Lower Side Panel The quarter panel is secured by 4 (4mm) hex screws, 2 (10mm) bolts, and 2 panel snaps. The side panel is secured by 1 bolt, 2 panel snaps & gas cap. Remove the 4 hex screws and 2 bolts first. Remove both panel snaps near the front of the panel. Remove the 2 panel snaps located at the top of the panel. Next remove the one bolt near the seat belt bolt. 4. Once all are removed safely pull the panel away from the vehicle. 4. Remove the gas cap 5. Lift away and remove J Removing Under Seat Tank Cover Shroud is secured by 4 panel snaps & 1 (17mm) seat belt bolt Remove the 4 panel snaps using a panel removal tool Using a 17mm socket remove the seat belt bolt. 4. Pull the seatbelt out of the plastic shroud & remove the tank cover K Rear panel is secured by 5 (10mm) bolts and 3 panel snaps extract and remove.
Illustration A Illustration B Cut Panel L Cutting the Rear Panel to size for the Subwoofer Cut the included template to size. Line up the holes along the top of the template to the holes located at the top of the panel. (Illustration A) Use the illustration above to understand how to line up the template. 4. The template will provide you with the guides to mark along the top of the panel. 5. Once marked you will need to follow the segmented lines on Illustration B to mark the rest of the panel. 6. This part is easy because you will follow factory panel lines to remove. M When the Subwoofer Enclosure is mounted in position it will be really difficult to remove the oil sump cover. We recommend cutting it in half to easily remove it for future serviceability. Before you put the sub enclosure into position remove the oil sump cover by extracting (3) 10mm bolts along the parameter. Cut the cover in half leaving the front half with the 2 factory bolt hole provisions and the back half with the one bolt hole position. Be sure to split it before the cover wraps around the back of the oil sump. 4. This will allow you to remove the front half of the cover and gain access to the oil drain when needed in the future.
N O Install the subwoofer enclosure into position by approaching 4. it from the inner wheel well. 5. First you will want to place the top bracket around the chassis tube to use as a guide for positioning the sub enclosure. Lift up and angle the top of the enclosure towards the bracket. Gently place the enclosure on the floor in front of the rear tire with the sub facing towards the cab of the vehicle. Next loosely install the side cage bracket using (4) Philips bolts and (4) Washers. 6. Once in position fasten the top bracket loosely around the chassis to the enclosure with (4) Philips screws and (4) Washers. P Install the T bracket using (2) Philips Screws and (2) washers. Q Use a (1) Philips Screw (2) Washer and (1) Nut to through bolt the T bracket to the vehicle chassis. Use (3) M6 Philips screws and (3) M6 washers to fasten the bottom of the sub enclosure to the panel below. R Next, go back and tighten all the screws securing the brackets to the sub enclosure.
T Install the new seat belt shroud by using a factory 10mm bolt to secure in position. Install the cut rear panel back into position. Use (2) Philips screws to secure the rear panel to the threaded inserts on the sub enclosure to help minimize vibration. Run all necessary cabling and re-assemble factory panels WIRING INSTRUCTIONS + - + - Amplifier For proper sound, ensure the speaker polarity is correct connect the + to the + and the - to the - from the speaker wire to the amplifier. If using with an SSV Works complete system refer to the amplifier wiring instructions for more detailed wiring information. 2017 SSV Works, Oxnard, CA 93030 Rev. B 4-11-17