Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics ervice Axial piston pump A10V()O with electro-hydraulic pressure control ED../ER.. RE 92707/11.10 1/12 Replaces: 03.08 Data sheet for variable pumps A10V()O series 31 and 32 A10VO series 52 and 53 open circuit A10V()O...Ex../3x Position Foto (oben links): X = 147 Y = 93,9 A10VO...Ex../5x Contents Ordering code for standard program, series 3x 2 Ordering code for standard program, series 5x 3 ED - electro-hydraulic pressure control, series 3x 4 ED - electro-hydraulic pressure control, series 5x 5 ER - electro-hydraulic pressure control, series 3x 6 Features Electro-hydraulic pressure control, current dependent High control accuracy Fail safe characteristic in case of power failure e.g. ED-applications for hydraulic fan drives Compatible with the use of standard proportional amplifiers ER - electro-hydraulic pressure control, series 5x 7 Dimensions ED / ER series 3x 8 Dimensions ED / ER series 5x 8 olenoid connectors 9 Notes 10 General instructions 12 Further information: Variable pump A10VO/31 RE 92711 Variable pump A10VO/31 RE 92701 Variable pump A10VO/32 RE 92714 Variable pump A10VO/32 RE 92705 Variable pump A10VO/52; 53 RE 92703
2/12 osch Rexroth AG A10V()O with electro-hydraulic pressure control ED/ER RE 92707/11.10 Ordering code for standard program series 3x A10V() O / 3x 01 02 03 04 05 06 07 08 09 10 11 12 13 Axial piston unit 018 028 045 071 100 140 180 01 washplate design, variable Operating mode A10V A10V 02 Pump, open circuit O ize 03 Displacement V g in cm 3 018 028 045 071 100 140 180 Control device 018 028 045 071 100 140 180 Electro-hydraulic pressure control ED (negative I-p characteristic) 04 Electro-hydraulic pressure control ER (positive I-p characteristic) 1) Noal voltage (V) Nom. current I N (A) 018 028 045 071 100 140 180 12 1,2 l l l l l 71 05 24 0,6 l l l l l l l 72 eries eries 3, Index 1 l l l l 31 06 eries 3, Index 2 m 32 For all further information regarding type code items 07 to 12 please consult the data sheets RE 92701, 92711, 92712 and 92714 olenoid connectors DEUTCH - plug, permanently molded; 2-pole - without suppressor diode 13 HIRCHMANN - plug - without suppressor diode (only for A10 VO) l l l l l l l P l l l l l l l H 1) At project design, the following must be considered: Excessive current levels(i > 1200 ma at 12 V or I > 600 ma at 24 V) to the ER-solenoid can result in undesired increase of pressure which can lead to pump or system damage: - Use I -current limiter. - Use an additionsl pressure relief valve in the system or a sandwich plate pressure reducing valve. An accessory kit with pressure reducing sandwich plate can be ordered from Rexroth under part number R902490825. = available m = on request = not available
RE 92707/11.10 A10V()O with electro-hydraulic pressure control ED/ER osch Rexroth AG 3/12 Ordering code for standard program series 5x A10V O / 5x 01 02 03 04 05 06 07 08 09 10 11 12 13 Axial piston unit 01 washplate design, variable A10V Operating mode 02 Pump, open circuit O ize 03 Displacement V g in cm 3 018 028 045 063 085 Control device 018 028 045 063 085 Electro-hydraulic pressure control ED (negative I-p characteristic) 04 Electro-hydraulic pressure control l l l l l ER (positive I-p characteristic) 1) Noal voltage (V) Nom. current I N (A) 018 028 045 063 085 12 1,2 l l l l 71 05 24 0,6 l l l l l 72 eries eries 5, Index 2 l l l 52 06 eries 5, Index 3 l m m m m 53 For all further information regarding type code items 07 to 12 please consult the data sheet RE 92703. olenoid connectors DEUTCH - plug, permanently molded; 13 2-polig - without suppressor diode l l l l l P 1) At project design, the following must be considered: Excessive current levels(i > 1200 ma at 12 V or I > 600 ma at 24V) to the ER-solenoid can result in undesired increase of pressure which can lead to pump or system damage: - Use I -current limiter. - Use an additionsl pressure relief valve in the system or a sandwich plate pressure reducing valve. An accessory kit with pressure reducing sandwich plate can be ordered from Rexroth under part number R902490825. = available m = on request = not available
4/12 osch Rexroth AG A10V()O with electro-hydraulic pressure control ED/ER RE 92707/11.10 ED - Electro-hydraulic pressure control; series 3x The. pump output pressure is set through a command current signal to the ED-valve solenoid When system pressure (load pressure) reaches this pressure level, the pump s control valve spool shifts and causes an increase or decrease in the pump s swivel angle (flow) in order to maintain this set pressure level. The pump output flow matches the needed input flow to the actuators. The desired pressure level can be set steplessly by varying the solenoid current. When the solenoid current signal drops towards a zero value, the imum output pressure is limited by an adjustable mechanical pressure cut off (secure fail safe function in case of a loss of power e.g. for use as fan drives). The response time characteristic of the ED-control was optimized for the use as a fan drive system. When ordering, state the type of application in clear text. Influence of pressure setting on standby level tand by [bar] 30 28 26 24 22 20 18 16 14 120 140 160 180 200 220 240 260 280 Max. pressure setting [bar] chematic A10V()O...ED../3x tatic current-pressure characteristic (negative characteristic) (measured with pump in standby) L Operating pressure [bar] 280 140 0 ED De-activation of control Amperage Max. adjustable control pressure Min. adjustable control pressure I/I 1 Hysteresis of static current-press. characteristic < 3bar Port for ervice line Inlet line L, L 1 Case drain (L 1 plugged) L 1 tatic flow-pressure characteristic (at n= 1500-1; t fluid = 50 C) operating pressure p [bar] etting range 280 140 Flow q v [L/] Hysteresise / pressure rise p Control data tandby standard settings (see diagramm to the right), other values on request. Hysteresis and pressure rise p < 4bar. Pilot flow consumption: 3-4,5 L/. Technical data, solenoids ED71 ED72 Voltage 12 V (±20 %) 24 V (±20 %) Control current Control begin at q v 100 ma 50 ma End of control at q v 1200 ma 600 ma Limit current 1,54 A 0,77 A Nom. resistance (at 20 C) 5,5 Ω 22,7 Ω Dither frequency 100-200 Hz 100-200 Hz Duty cycle 100 % 100 % olenoid class of material Type of protection H (T = 180 C) see connector selection page 9 Operating temperature range at valve -20 C to +115 C
RE 92707/11.10 A10V()O with electro-hydraulic pressure control ED/ER osch Rexroth AG 5/12 ED - Electro-hydraulic pressure control; series 5x The. pump output pressure is set through a command current signal to the ED-valve solenoid When system pressure (load pressure) reaches this pressure level, the pump s control valve spool shifts and causes an increase or decrease in the pump s swivel angle (flow) in order to maintain this set pressure level. The pump output flow matches the needed input flow to the actuators. The desired pressure level can be set steplessly by varying the solenoid current. When the solenoid current signal drops towards a zero value, the. output pressure is limited by an adjustable mechanical pressure cut off (secure fail safe function in case of a loss of power e.g. for use as fan drives). The response time characteristic of the ED-control was optimized for the use as a fan drive system. When ordering, state the type of application in clear text. chematic A10VO...ED../5x L tatic current-pressure characteristic (negative characteristic) (measured with pump in standby) Operating pressure [bar] 250 140 0 Hysteresis static current-pressure characteristic < 3bar tatic flow-pressure characteristic (at n= 1500rpm; t fluid = 50 C) Operating pressure p [bar] etting range 250 140 ED De-activation of control Amperage Max. adjustable control pressure Min. adjustable control pressure Flow q v [L/] I/I 1 Hysteresis / pressure rise p Port for ervice line Inlet line L, L 1 Case drain (L 1 plugged) Technical data, solenoids ED71 ED72 Voltage 12 V (±20 %) 24 V (±20 %) Control current Control begin at q v 100 ma 50 ma End of control at q v 1200 ma 600 ma Limit current 1,54 A 0,77 A Nom. resistance (at 20 C) 5,5 Ω 22,7 Ω Dither frequency 100-200 Hz 100-200 Hz Duty cycle 100 % 100 % olenoid class of material Type of protection H (T = 180 C) see connector selection page 9 Operating temperature range at valve -20 C to +115 C L 1 Control data tandby standard settings 20bar, other values on request. Hysteresis and pressure rise p < 4bar. Pilot flow consumption: 3-4,5 L/.
6/12 osch Rexroth AG A10V()O with electro-hydraulic pressure control ED/ER RE 92707/11.10 ER - Electro-hydraulic pressure control; series 3x The. pump output pressure is set through a command current signal to the ED-valve solenoid When system pressure (load pressure) reaches this pressure level, the pump s control valve spool shifts and causes an increase or decrease in the pump s swivel angle (flow) in order to maintain this set pressure level. The pump output flow matches the needed input flow to the actuators. The desired pressure level can be set steplessly by varying the solenoid current. When the solenoid current signal drops towards a zero value, the pump s output pressure will also drop to the standby level. Observe the instructions regarding the project design on page 2 tatic current-pressure characteristic (positive characteristic) (measured with pump in standby) chematic A10V()O...ER../3x L 350 L 1 Operating pressure [bar] 250 150 Max. adjustable control pressure 50 Min. adjustable control pressure 0 0 1 Amperage I/I Port for ervice line Inlet line L, L 1 Case draint (L 1 plugged) Hysteresis static current-pressure characteristic < 3bar Influence of pressure setting on stand by ± 2bar tatic flow-pressure characteristic (at n= 1500 rpm; t fluid = 50 C) 280 Operating pressure p [bar] etting range 140 Flow q v [L/] Hysteresis / pressure rise p Technical data, solenoids ER71 ER72 Voltage 12 V (±20 %) 24 V (±20 %) Control current Control begin at q v 100 ma 50 ma End of control at q v 1200 ma 600 ma Limit current 1,54 A 0,77 A Nom. resistance (at 20 C) 5,5 Ω 22,7 Ω Dither frequency 100-200 Hz 100-200 Hz Duty cycle 100 % 100 % olenoid class of material Type of protection H (T = 180 C) see solenoid selection page 7 Operating temperature range at valve -20 C to +115 C Control data tandby standard setting 20bar, other values on request. Hysteresis and pressure rise p < 4bar. Pilot flow consumption: 3-4,5 L/.
RE 92707/11.10 A10V()O with electro-hydraulic pressure control ED/ER osch Rexroth AG 7/12 ER - Electro-hydraulic pressure control; series 5x The. pump output pressure is set through a command current signal to the ED-valve solenoid When system pressure (load pressure) reaches this pressure level, the pump s control valve spool shifts and causes an increase or decrease in the pump s swivel angle (flow) in order to maintain this set pressure level. The pump output flow matches the needed input flow to the actuators. The desired pressure level can be set steplessly by varying the solenoid current. When the solenoid current signal drops towards a zero value, the pump s output pressure will also drop to the standby level. Observe the instructions regarding the project design on page 2 tatic current-pressure characteristic (positive characteristic) (measured with pump in standby) chematic A10VO...ER../5x L 350 L 1 Operating pressure [bar] 250 150 Min. 50 adjustable control pressure 0 0 1 I/I Hysteresis static current-pressure characteristic < 3bar Influence of pressure setting on stand by ± 2bar tatic flow-pressure characteristic (at n= 1500 rpm; t fluid = 50 C) Operating pressure p [bar] etting range 250 140 Max. adjustable control pressure Amperage Flow q v [L/] Hysteresis / pressure rise p Port for ervice line Inlet line L, L 1 Case drain (L 1 plugged) Technical data, solenoid ER71 ER72 Voltage 12 V (±20 %) 24 V (±20 %) Control current Control begin at q v 100 ma 50 ma End of control at q v 1200 ma 600 ma Limit current 1,54 A 0,77 A Nom. resistance (at 20 C) 5,5 Ω 22,7 Ω Dither frequency 100-200 Hz 100-200 Hz Duty cycle 100 % 100 % olenoid class of material Type of protection H (T = 180 C) see connector selection page 7 Operating temperature range at valve -20 C to +115 C Control data tandby standard setting 20bar, other values on request. Hysteresis and pressure rise p < 4bar. Pilot flow consumption: 3-4,5 L/.
8/12 osch Rexroth AG A10V()O with electro-hydraulic pressure control ED/ER RE 92707/11.10 Dimensions ED / ER series 3x Valve mounting on port plate 11; 41 for size 71 Connector H Connector P efore finalising your design request a certified installation drawing. Dimensions in mm. Dimensions series 31 for port plate 11 (41 size 71) and 12 (42 size 71) Port plate 11 (41size71) Port plate 12 (42 size 71) A2 Z View Z ize A 1 ED/ER 1) A 1 ER 2) A 2 A 3 A 4 18 126 140 28 255 290 143 136 140 45 244 279 140 146 140 71 278 313 140 160 140 100 344 379 140 165 140 140 349 384 138 179 129 A 1 Clockwise rotation Valve mounting C. clockwise rotation Valve mounting on port plate 12; 42 for size 71 Z Connector H View Z Clockwise rotation Connector P A 3 Valve mounting A4 C. clockwise rotation Dimensions series 32 for port plate 11 and 12 Port plate 11 Port plate 12 ize A 1 A 1 A 2 A 3 ED/ER 1) A 3 ER 2) A 4 Mounting flange C/D 45 245 245 140 146 181 140 71 288 291 140 160 195 140 100 338 342 140 165 200 140 140 358 362 138 179 214 129 180 374 374 138 179 214 129 For detailed dimensions and technical data on the variable pumps see data sheets A10VO 18...140 RE 92711; 45...180 RE 92714 und A10VO 18...140 RE 92701. Additional information can be found unde olenoid connectors on page 9 Dimensions ED / ER series 5x Valve mounting ED / ER Dimensions series 52 ize A 1 A 2 ED/ER 1) A 2 ER 2) 28 240 124 159 A 1 A2 View Z Connector P 45 250 132 167 63 250 137 172 85 272 156 191 Dimensions series 53 Z ize A 1 A 2 ED/ER 1) A 2 ER 2) 18 213 121.9 156.9 For detailed dimensions and technical data on the variable pump see data sheet A10VO RE 92703. Additional information can be found under olenoid connectors on page 9 1) 2) without pressure reducing sandwich plate with pressure reducing sandwich plate
RE 92707/11.10 A10V()O with electro-hydraulic pressure control ED/ER osch Rexroth AG 9/12 olenoid connectors DEUTCH DT04-2P-EP04, 2-pole permanently molded, without bidirectional suppressor diode (tandard) P Type of protection to DIN/EN 60529: IP67K Type of protection to DIN 40050-9 IP 69K Mating connector DEUTCH DT06-2-EP04 Rexroth Mat.-Nr. R902601804 Comprising: DT-Designation 1 Housing DT06-2-EP04 1 Key W2 2 ushings 0462-201-16141 The mating plug is not included in the supply. This item is available on request from Rexroth. HIRCHMANN DIN EN 175 301-803-A /IO 4400 (only A10VO) without bi-directional suppressor diode H Protection to DIN/EN 60529: IP65 The cable joint sealing ring is suitable for cable diameters from 4,5 mm to 10 mm. The HIRCHMANN-connector is included in the supply of the pump. Fastening screw M3 Tightening torque: M A = 0.5 Nm 65.4 (2) Cable joint M16x1.5 Tightening torque: M A = 1.5-2.5 Nm (1) 36 (2) (1) 50 Ø37 Ø37 68.5 50 68.5 Note: Plug orientation can be changed by rotation of the solenoid body. Please observe the following procedure: 1. Loosen the fastening nut (1) 2. Rotate the solenoid body (2) into the desired orientation 3. Retighten fastening nut Tightening torque: 5 +1 Nm (wrench size across flats W26, 12kt DIN 3124) Electronic controls Control Electronic function Electronics Further information Elektric pressure control Regulated current output 1)Current outputs for 2 valves, separately controllable 2)Only 24V noal voltage RA analogue RE 95 230 RC2-2/21 1) digital RE 95 201 VT2000 2) analogue RE 29 904 VT 11029 2) ; VT 11030 2) analogue RE 29741
10/12 osch Rexroth AG A10V()O with electro-hydraulic pressure control ED/ER RE 92707/11.10 Notes
RE 92707/11.10 A10V()O with electro-hydraulic pressure control ED/ER osch Rexroth AG 11/12 Notes
12/12 osch Rexroth AG A10V()O with electro-hydraulic pressure control ED/ER RE 92707/11.10 General instructions The pump A10VO/A10VO has been designed to be used in open and closed circuits. Project planning, assembly and commissioning of the axial piston unit require the involvement of qualified personnel. efore operating the axial piston unit read the relevant operating manual thoroughly and completely. If needed request this information from Rexroth During and shortly after operation, there is a risk of burns on the axial piston unit and especially on the solenoids. Take appropriate safety measures (e.g. by wearing protective clothing). Depending on the operating conditions of the axial piston unit (operating pressure, fluid temperature), the characteristic may shift. --Pressure ports: The ports and mounting bolts threads are designed for the specified imum pressure. The machine or system manufacturer must ensure that the connecting elements and lines correspond to the specified operating conditions (pressure, flow, hydraulic fluid, temperature) with the necessary safety factors. The service line ports and function ports are only designed to accommodate hydraulic lines. The data and notes contained herein must be adhered to. The product is not approved as a component for the safety concept of a general machine according to DIN EN IO 13849. The following tightening torques apply: --Fittings: Observe the manufacturer s instructions regarding the tightening torques of the fittings used. --Mounting bolts: For mounting bolts according to DIN 13, we recommend checking the tightening torque individually according to VDI 2230. --Mounting bolts threads and threaded ports in the axial piston unit: The imum permissible tightening torques M G are imum values for the female threads and must not be exceeded. For values, see the relevant A10VO/A10VO data sheets. --Threaded plugs: For the threaded plugs, supplied with the axial piston unit, the required tightening torques M V apply. For values see the appropriate data sheets of the A10VO/A10VO pumps. osch Rexroth AG Hydraulics Axial Piston Units An den Kelterwiesen 14 72160 Horb a.n., Germany Telephone +49 (0) 74 51 92-0 Fax +49 (0) 74 51 82 21 info.brm-ak@boschrexroth.de www.boschrexroth.com/axial-piston-motor Alle Rechte bei osch Rexroth AG, auch für den Fall von chutzrechtsanmeldungen. Jede Verfügungsbefugnis, wie Kopier- und Weitergaberecht, bei uns. Die angegebenen Daten dienen allein der Produktbeschreibung. Eine Aussage über eine bestimmte eschaffenheit oder eine Eignung für einen bestimmten Einsatzzweck kann aus unseren Angaben nicht abgeleitet werden. Die Angaben entbinden den Verwender nicht von eigenen eurteilungen und Prüfungen. Es ist zu beachten, dass unsere Produkte einem natürlichen Verschleiß- und Alterungsprozess unterliegen. Änderungen vorbehalten.