"AR" SERIES Variable Displacement-Single Pumps Compensator Type,AR / AR- FR Up to MPa ( PSI),. cm /rev (.5 CU.IN./rev) Pub. EC- A Compensator Valve Adj. Screw Spool Control Piston Drain Port Flow Adj. Screw OUT Pivot Journal Bearing Graphic Symbol IN Shaft M O Port Plate Cylinder Block Yoke Slipper Retainer Spring Piston Ass'y Features Smaller in Size and Lighter in Mass As indicated in the dimensional comparison presented below, the AR is smaller than the A ( design). Also, the mass of AR is substantially lighter than the A. Low Noise The noise level of AR has been reduced by - db (A) at full flow and full cut-off compared with that of the excellent A quiet pump. [Comparison of "AR" with "A"] A, Design.5(.7) AR, Design (7. 9(7.) 7(7.) DIMENSIONS IN MILLIMETRES (INCHES) (9.5) (5. Model AR A Approx. Mass (Flange Mtg.) 9. kg (. lbs.).5 kg (. lbs.) Ratio of Mass (AR/A) % No.
"AR" Series Piston Pumps AR / AR-FR Instructions Instructions. Hydraulic Fluids Use petroleum base oils such as anti-wear type hydraulic oils or R & O (Rust and Oxidation inhibitor) type hydraulic oils equivalent to ISO VG- or. The recommended viscosity range is from to mm /s (9 to SSU) and temperature range is from to C ( to F), both of which have to be satisfied for the use of the above hydraulic oils.. Control of Contaation Due caution must be paid to maintaining control over contaation of the operating oil which can otherwise lead to breakdowns and shorten the life of the unit. Please maintain the degree of contaation within NAS Grade. The suction port must be equipped with at least a µm (5 mesh) reservoir type filter and the return line must have a line filter of under µm.. Mounting When installing the pump the filling port should be positioned upwards.. Alignment of Shaft Employ a flexible coupling whenever possible, and avoid any stress from bending or thrust. Maximum permissible misalignment is less than. mm (. inches) TIR and maximum permissible misangular is less than.. 5. Suction Permissible suction pressure at inlet port of the pump is between - and +5 kpa (5 in.hg Vacuum and 7 PSIG). For piping to the suction port, use the pipes of the same diametre as that of the specified pipe flange to be used. Make sure that the height of the pump suction port is within one metre (. ft) from the oil level in the reservoir.. Hints on Piping When using steel pipes for the suction or discharge ports, excessive load from the piping to the pump generates excessive noise. Whenever there is fear of excessive load, please use rubber hoses. 7. Suction Piping In case the pump is installed above the oil level, the suction piping and suction line filter should be located lower than the pump position to prevent air in the suction line.. Drain Piping Model AR, AR Fitting Size / [Inside Dia..5 mm (. in.) or more] Install drain piping according to the chart and ensure that pressure within the pump housing should be maintained at a normal pressure of less than. MPa (.5 PSI) and surge pressure of less than.5 MPa (7.5 PSI). Length of piping should be less than m (. ft.), and the pipe end should be submerged in oil. In case AR and AR pump, a screw-in torque of fitting is to 5 Nm (5 to IN.bs.). Do not apply bending and thrust torque to the fitting. [Recommended Drain Piping Size] Inside Dia. of Pipe mm (.9 in.) 9. Bleeding Air It may be necessary to bleed air from pump case and outlet line to remove causes of vibration. An air bleed valve (Model No. ST- -, Catalogue No.: Pub. EC- ) is recommended for this purpose. No.
"AR" Series Piston Pumps AR / AR-FR Instructions. Starting Before first staring, fill pump case with clean operating oil via the fill port. In order to avoid air blockage when first starting, adjust the control valves so that the discharged oil from the pump is returned direct to the tank or the actuator moves in a free load. [Volume of Pre-fill Oil Required] A Model AR AR Volume cm (in.) (.). Setting Discharge and Delivery At the time of shipment, the unit has been preset to maximum delivery and imum discharge pressure Adjust the preset delivery and pressure to meet your system requirements. Adjustment of Discharge Turning the adjustment screw clockwise, increases pressure. Volume adjusted by each full turn of the pressure adjustment screw Model Numbers AR/AR-FRB AR/AR-FRC Adjustment Volume MPa (PSI).9 () 5. (7) Adjustment of Delivery Turning the delivery adjustment screw clockwise, decreases delivery. The imum adjustable flow and adjustable volume of each full turn of the delivery adjustment screw Model Numbers AR AR Adjustable volume with each full turn of the adjustment screw cm /rev (cu.in./rev).5 (.9). (.) Minimum adjustable flow cm /rev (cu.in./rev) (.).5 (.59) No.
"AR" Series Piston Pumps AR / AR-FR Specifications / Model Number Designation / Pipe Graphic Symbol M O Specifications Model Numbers AR-FR -// 9 Geometric Displacement cm /rev (cu.in./rev) 5. (.9). (.55) Operating Pres. MPa (PSI) Shaft Speed Range r/. Rated Intermittent Max. Min. () Approx. Mass kg (lbs.) 9. (.). When setting the pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure. Model Number Designation AR -F R B - Series Number Mounting Direction of Rotation Control Type Pres. Adj. Range MPa (PSI) Design Number Design Std. AR (5. cm /rev) AR (. cm /rev) F: Flange Mtg. Viewed from Shaft End R: Clockwise (Normal) : Compensator Type B:. - 7 {7 - } C:. - {9 - } Refer to. Available to supply pump with anti-clockwise rotation.. Design Standards: Consult Yuken for details. None...Japanese Standard "JIS"... European Design Standard 9... N. American Design Standard Pipe Flange Kits Pipe flange kits are available. When ordering, specify the kit number from the table below. Pump Model Numbers AR-FR AR-FR Name of Port Suction Discharge Japanese Standard "JIS" Threaded Connection European Design Standard Pipe Flange Kit Numbers N. American Design Standard Japanese Standard "JIS" European Design Socket Welding N. American Design Standard F5--A- F5--A- F5--A-9 F5--B- F5--B-9 Discharge port is available only for the threaded connections. No.
"AR" Series Piston Pumps AR / AR - FR Pipe Flange Kits/Mounting Bracket Kits A Pipe Flange Kit for Suction Port (.) Dia. Through Places (.) 7. (.7) (.9). (.7) F5--A-/9 F5--B-/9 "C" Thd. (.) SO-NB-G 7.7 (.9) Dia. (.) 5 (.59) SO-NB-G Soc. Hd. Cap Screw ( Pcs.) D D Soc. Hd. Cap Screw ( Pcs.) Kit Numbers "C" Thd. D mm (IN.) Soc. Hd. Cap Screw Approx. Mass kg (lbs.) F5--A- 9 Rc / 5 5 (.59) (.59) M Lg. M 5 Lg. F5--A- F5--B- / NPT.75.5 (.) (.57) /-UNC -/ Lg. /-UNC -/ Lg..5 (.). (.) (.) Dia. Through 7.5(.9) C' bore.(.) Deep Places F5--A- (.9). (.7).-.5 (.-.) (.) (.79) / BSP. F Thd. SO-NB-G 7(.7) 7. (.7) Approx. Mass....5 kg (. lbs.) Soc. Hd. Cap Screw ( Pcs.) M 5 Lg.. (.5) Mounting Bracket Kits Mounting bracket available on separate order. Pump Model Numbers Mtg. Bracket Kit Numbers Approx. Mass kg (lbs.) AR/AR-FR LP-A-. (.9) Mtg. Bracket Mtg. Bracket Kit: LP-A- 7 (.7) (.7) Dia. Through (.9) Dia. Spotface Places DIMENSIONS IN MILLIMETRES (INCHES) N ote: The mounting bracket kit consists of a mounting bracket, hex. bolts and plain washers. Hex. Bolt ( Pcs.) M 5 Lg. Plain Washer ( Pcs.) 5 5.5 (.97) (. 95 (.7) 7.5 (.) (.) 95 (. 7.5 (. 5) 7.5 (. 5) (7.9) (.55) 5 (.59) (.5) 5.5 (5.7) No.5
"AR" Series Piston Pumps AR-FR Typical Pump Characteristics Type "AR " Efficiency % Viscosity mm /s ( SSU) [ISO VG Oils,5 C ( F)] Performance Characteristic Curve N=5 r/ Volumetric Efficiency Overall Efficiency L/ MPa U.S.GPM Efficiency % N= r/ Volumetric Efficiency Overall Efficiency L/ U.S.GPM MPa 5 5 PSI N=5 r/ P=MPa(PSI) P= () P= (7) P= (5) P= () P= (7) P= (5) P= (9) P=.7 () 5 5 5 L/ 5 7 U.S.GPM Power Drain in. / 5 5 PSI N= r/ 5 5 5 L/ L/. P=MPa(PSI) P= () P= (7) P= (5) P= () P= (7) P= (5) P= (9) P=.7 () 5 7 U.S.GPM Power..5.5..5..5 r/ 5 r/ MPa Drain.5..5 5, r/ N= r/ N=5 r/ MPa db(a) 5 5 PSI Noise Level [One metre (. ft.) horizontally away from pump head cover] N=5 r/ db(a) 5 5 PSI N= r/ Noise Level 7 5 MPa Noise Level 7 5 MPa No. 5 5 PSI 5 5 PSI
Type "AR " Efficiency Typical Pump Characteristics Viscosity mm /s ( SSU) [ISO VG Oils,5 C ( F)] Performance Characteristic Curve % N=5 r/ Volumetric Efficiency L/ Overall Efficiency U.S.GPM MPa "AR" Series Piston Pumps AR-FR Efficiency % N= r/ Volumetric Efficiency L/ U.S.GPM Overall Efficiency MPa A 5 5 PSI N=5 r/ P=MPa(PSI) P= () P= (7) P= (5) P= () P= (7) P= (5) P= (9) P= (5) 5 L/ 5 5 PSI N= r/ P=MPa(PSI) P= () P= (7) P= (5) P= () P= (7) P= (5) P= (9) P= (5) 5 L/ Power..5..5.5..5 U.S.GPM Power r/ 5 r/ MPa in. / Drain Drain L/..5..5 U.S.GPM 5 r/ r/ 5, r/ MPa db(a) 5 5 PSI Noise Level [One metre (. ft.) horizontally away from pump head cover] N=5 r/ db(a) 5 5 PSI N= r/ Noise Level 7 Noise Level 7 5 MPa 5 MPa 5 5 PSI 5 5 PSI No.7
"AR" Series Variable Displacement Piston Pumps Single Pump, Compensator Type Response Characteristics / Installation Drawing Response Characteristics Change in Accordance with Circuits and Operating Conditions. Test Circuit and Conditions Circuit Result of Measurement t t Ps SOL Hydraulic High Hose /" m (. ft.) P M O Conditions Drive Speed : 5 r/ Hydraulic Fluid : ISO VG oil Oil Temperature : 5 C ( F) Viscosity : mm /s ( SSU) MPa (9 PSI) MPa (9 PSI) Time SOL OFF ON OFF Model P MPa (PSI) AR AR () Response Time ms t t 7 5 7 Overshoot MPa (PSI) 5. () 7. () AR-FR -//9 AR-FR -//9 "E" Thd. 7(.7) Deep Places Suction Port 9(.75) Dia. 7. (. 7). (.7).5.5 (. (. ) ) (.7) Lock Nut (.5) Hex. Flow Adj. Screw (.5) Hex. DEC. 5 (.97) Gauge Connection "F" Thd Discharge Port "C" Thd. 95.5(7. 7 (5.79) 7 (.77) Filling Port [(.7) Hex. Head Plug Furnished] (.).5 (..5 (.) 5 (. (.9) 9.5(.75) 9.(.7) Dia..(..(. Drain Port "D" Thd..55(.5).5(.) Dia.. Install the pump so that the "Filling port" is at the top.. A screw-in torque of fitting is - 5 Nm (5- IN. lbs.). Do not apply bending and thrust torque to the fitting. 77 (.) (.7) DIMENSIONS IN MILLIMETRES (INCHES) 5.5(..5 (.9).79(.).7(.7) (.7) (5.) (.) Lock Nut (.5) Hex. Adj. Screw (.5) Hex. 9 (.7) (.9) 7 (.99) 95(.7) Dia. INC. Model Numbers AR/AR-FR - AR/AR-FR - "C" Thd. Rc / / BSP.F "D" Thd. Rc / / BSP.F "E" Thd. M "F" Thd. Rc / / BSP.Tr / NPT / NPT /- UNC / NPT No.
AR-FR -//9 AR-FR -//9 "AR" Series Piston Pumps AR / AR - FR Spare Parts List CAUTION When making replacement of seals or bearing, please do it carefully after reading through the relevant instructions in the Operator's Manual. A 5 9 5 7 7 5 Z Z 9 9 5 9 7 7 5 5 5 5 55 5 57 5 59 Section Z-Z Item 5 7 9 5 Name of Parts Gasket Bearing Bearing Oil Seal Pump Model Numbers AR-FR -//9 AR-FR -//9 Seal Kit Number KS-AR-- AR-FR HMK 75 V Part Numbers -PK9-5 5 TCN 55 SO-NB-P9 SO-NA-P SO-NB-P SO-NA-A SO-NB-P AR-FR Z--PK- When ordering seals, please specify the seal kit number from the table below. Qty. No.9
Specifications Model Description Geometric Displacement Operating Rated Pres. Intermittent Shaft Speed Range Approx. Mass (Flange Mtg.) Interchangeability in Installation "A" Series A- -R-- -K- A- -R-- -K- Model Numbers A/A-F-R-- -K Flow Adj. Screw Interchangeability in Installation between "A" Series and "AR" Series A- -R-- -K- AR-FR - A- -R-- -K- AR-FR - 5. cm /rev (.9 cu.in./rev). cm /rev (.55 cu.in./rev) MPa ( PSI) MPa (5 PSI) MPa ( PSI) - r/.5 kg (. lbs.) 9. kg (. lbs.) "AR" Series AR-FR - AR-FR - Adj. Screw "AR" Series Piston Pumps AR / AR - FR MPa ( PSI) MPa ( PSI) - r/.5 kg (. lbs.) 9. kg (. lbs.) Interchangeability in Installation Mtg. Flange & Piping Shaft End Suction Port Discharge Port Drain Port Yes Yes No No Comparison of dimensions between "A" series and "AR" series are shown below. Note:Dimensions with star mark are identical to each other. 9.5 59.5.5 Filling Port Drain Port "D" Thd. 7. 7 9 5 φ9.5-..-. -.5 φ.55 9 +..7 Suction Port 9 Dia. 5. "E" Thd. 7 Deep Places Discharge Port 9 Dia. 7 φ95 R No. AR/AR-FR "E" Thd. 7 Deep Places 7. Suction Port 9 Dia... Flow Adj. Screw. 5 Gauge Connection "F" Thd. Model Numbers A/A-F-R-- -K- A/A-F-R-- -K- AR/-FR - AR/-FR - AR/-FR -9 Filling Port. Drain Port "D" Thd. 95.5. 7 7 Discharge Port "C" Thd. 5 φ9.5-.. -. -.5 φ.55 77 "C" Thd. Rc / / BSP.F / NPT "D" Thd. Rc / / BSP.F / NPT Rc / / BSP.F / NPT 5.5. +..7 9 φ95 "E" Thd. M /- UNC M /- UNC 7 "F" Thd. Rc / / BSP.Tr / NPT Adj. Screw DIMENSIONS IN MILLIMETRES