BauBuche Efficiency 07-14 - EN Sheet 4 / 19 Bending strength, density and modulus of elasticity of BauBuche laminated veneer lumber in comparison with other materials. N/mm 2 kg/m 3 N/mm 2 70 48 28 120 235 680 480 410 2,700 7,850 16,800 13,800 12,600 70,000 210,000 BauBuche Spruce laminated veneer lumber Spruce glulam (GL28) Aluminium Steel (S235) Characteristic bending strength Characteristic density Modulus of elasticity Materials Solid wood Glulam LVL BauBuche C24 GL28 Spruce GL70 Key properties Bending f m 200 / 100 % 154 / 77 % 92 / 46 % 57 / 29 % Shear f v 200 / 100 % 240 / 120 % 112 / 56 % 104 / 52 % Compression f c,0 Lower material consumption The higher strength and stiffness values of BauBuche allow smaller cross-sections, which in turn results in major savings in material consumption. The dimensioning of a structure is determined by various properties depending on the particular application. In the case of single-span beams, deformation (stiffness) is generally the key factor, whereas with continuous beams, it is bending strength or shear strength; and with columns and frameworks it is compressive and tensile strength. The table on the left shows the amount of material saved when using GL 28 glued laminated timber, spruce laminated veneer lumber and BauBuche GL70 in comparison with C24 solid wood (usual con struction timber). This is based on the following assumptions: _ Use in utilisation class 1 _ Load-duration class: medium _ Consistent cross-section height of 300 mm _ Calculation according to EN 1995-1-1 200 / 100 % 152 / 76 % 102 / 51 % 56 / 28 % Tension f t,0 200 / 100 % 129 / 64 % 68 / 34 % 44 / 22 % E-modulus E mean 200 / 100 % 175 / 87 % 159 / 80 % 132 / 66 % Required width in mm at same load % Material consumption
BauBuche Comparison of BauBuche and spruce 07-14 - EN Sheet 5 / 19 Comparison of BauBuche and spruce glulam when used in a roof truss. Due to its greater strength and density, BauBuche allows considerably slimmer beams and less connectors for the same load. 200 N d = 300 kn, tensile splice double shear, internal steel plate, dowel pins split-proof by VGS BauBuche Beam 12 bolts ø12 160 60 90 50 50 Utilisation ratio of the bolts: 100 % 74 200 160 A = 32.000 mm 2 Comparison of fasteners of BauBuche beam and spruce glulam GL28h. Fasteners for BauBuche (beech laminated veneer lumber) must be dimensioned in compliance with section 4.2 according to EN 1995-1-1 in conjunction with EN 1995-1-1/NA with the equations for solid wood. Further details for the dimensioning of fasteners can be found in the general technical approvals no. Z-9.1-837 and Z-9.1-838. Spruce glulam GL28h 20 bolts ø12 94 240 240 50 200 200 60 90 45 A = 48.000 mm 2 Static calculation: Pirmin Jung Ingenieure für Holzbau AG
BauBuche Product Overview 07-14 - EN Sheet 7 / 19 Board BauBuche S/Q Surface qualities: surfaces unsanded, sanded (80 grit); saw-cut at the edge; (BauBuche Q contains approx. 20% cross-layers) Qualities Thicknesses [mm] s [mm] s [mm] Min. quantity Small-order surcharge Standard length, standard width 1850 mm, unsanded 42, 62, 82 1850 6000; 12000; 13500; 16000; 18000 < 3 m³ per thickness & length (excl. standard packs) Standard length, standard width 1850 mm, sanded Variable length, standard width 1850 mm, unsanded Variable length, standard width 1850 mm, sanded Standard length, variable width, unsanded 40, 60, 80 42, 62, 82 40, 60, 80 42, 62, 82 1850 1850 1850 100-1850 6000; 12000; 13500; 16000; 18000 2000-18100 2000-18100 6000; 12000; 13500; 16000; 18000 < 3 m³ per thickness & length (excl. standard packs) 3 m³ per length b) 3 m³ per length b) < 3 m³ per board size Standard length, variable width, sanded 40, 60, 80 100-1850 6000; 12000; 13500; 16000; 18000 < 3 m³ per board size Variable length, variable width, unsanded 42, 62, 82 100-1850 2000-18100 6 lin. m per cross-section < 3 m³ per board size Variable length, variable width, sanded 40, 60, 80 100-1850 2000-18100 6 lin. m per cross-section < 3 m³ per board size BauBuche Panel Surface qualities: surface sanded (80 grit), chamfered edge c) Standard length, range of widths, fixed quantity per cross-section Exposed Variable length, range of widths, fixed quantity per cross-section Exposed Standard length, range of widths, variable quantity per cross-sectionexposed Variable length, range of widths, variable quantity per cross-section Exposed Variable length, range of widths, variable quantity per cross-section Exposed 14, 20, 25, 45, 50, 60 d) 14, 20, 25, 45, 50, 60 d) 14, 20, 25, 45, 50, 60 d) 14, 20, 25, 45, 50, 60 d) 14, 20, 25, 45, 50, 60 d) 120, 160, 200, 440, 520, 560, 640, 680 120, 160, 200, 440, 520, 560, 640, 680 120, 160, 200, 440, 520, 560, 640, 680 120, 160, 200, 440, 520, 560, 640, 680 120, 160, 200, 440, 520, 560, 640, 680 6000, 12000, 13500 2000-13500 6000, 12000, 13500 2000-16500 500-2000 see standard pack units 8 lin. m per cross-section < 0.5 m³ per board size Beam BauBuche S Surface qualities: surfaces unsanded, edge precise saw-cut and chamfered c) ; surfaces sanded (80 grit), edge planed and chamfered c) Qualities [mm] Height [mm] s [mm] Min. quantity Small-order surcharge for Standard length, height in 40 mm steps, unsanded Standard length, height in 40 mm steps, sanded Variable length, height in 40 mm steps, unsanded Variable length, height in 40 mm steps, sanded 42, 62, 82 40, 60, 80 42, 62, 82 40, 60, 80 120, 160, 200, 240, 280, 320, 360, 400, 440, 480, 520, 560, 600 d) 120, 160, 200, 240, 280, 320, 360, 400, 440, 480, 520, 560, 600 d) 120, 160, 200, 240, 280, 320, 360, 400, 440, 480, 520, 560, 600 d) 120, 160, 200, 240, 280, 320, 360, 400, 440, 480, 520, 560, 600 d) 6000; 12000; 13500; 16000 6000; 12000; 13500; 16000 2000-18100 2000-18100 6 lin. m per cross-section 6 lin. m per cross-section < 3 m³ per beam size < 3 m³ per beam size Beam BauBuche GL70 Surface qualities: surface and edge sanded (80 grit), chamfered edge c) Camber up to 150 mm possible Standard length, height in 40 mm steps, fixed quantity per cross-section Variable length, height in 40 mm steps, variable quantity per cross-section a) National Technical Approval not yet issued b) Quantities below 3 m³ are invoiced with the prices for variable length, variable width c) Also available unchamfered, on request. d) Other dimensions on request 80 f), 120, 160, 200, 240, 280 d) 120, 160, 200, 240, 280, 320, 360, 400, 440, 480, 520, 560, 600, 12000, 13500, 16000, 18000 see standard pack units e) (640, 680, 720, 760, 800, 840, 880, 920, 960, 1000, 1040, 1080, 1120, 1160, 1200, 1240, 1280, 1320, 1360) a) 80 f), 120, 160, 200, 240, 280 d) 120, 160, 200, 240, 280, 320, 360, 400, 440, 480, 520, 560, 600, 2000-18100 (640, 680, 720, 760, 800, 840, 880, 920, 960, 1000, 1040, 1080, 1120, 1160, 1200, 1240, 1280, 1320, 1360) a) 8 lin. m per cross-section (with : at least 2 pcs per cross-section and length) < 1 m³ per order e) Quantities differing from standard packs (see standard pack dimensions) are invoiced with the prices for variable length (Example: Pack size = 8 pcs; calculation as per standard length, standard packs. If 9 pcs are ordered, the one extra piece is invoiced at the price for variable length.) f) For width the beam length is limited to 16500 mm.
BauBuche Product Data Sheet 07-14 - EN Sheet 8 / 19 SURFACE QUALITY Sanded, 80 grit, flaws which impare the look are corrected with a beech-look filler compound. Board and Beam BauBuche S also available unsanded. The top surface of boards has a high-quality finish Board BauBuche S/Q Beam BauBuche S Beam BauBuche GL70 BauBuche Panel for visible applications, while the bottom surface has a lower-quality finish for hidden areas. PACKAGING Standard packs of Beam BauBuche S, Beam BauBuche GL70 Beams individually film-wrapped Packs wrapped in stretch film Base/liner also encompassed by strapping Consignment packs only outer film-wrapping of whole pack; individual film-wrapping on request (surcharge) Board packs > 1350 mm width: packed with centre-folded film Board packs < 1350 mm width: outer film-wrapping of whole pack Panel packs: outer film-wrapping of whole pack SPECIFICATIONS Dimensional tolerances tolerance ± 5 mm tolerance ± 2 mm Height tolerance h 400 mm + 4 mm/- 2 mm h > 400 mm + 1%/- 0.5% Thickness tolerance (board) ± 1 mm Cross-section angle Max. deviation from right angle: 1.1 Wood moisture content approx. 8% The stated tolerances refer to a target moisture of 8% ex works Creuzburg. The swelling and shrinking behaviour of higher equilibrium moisture contents must be taken into account. Note: BauBuche must never be directly exposed to weather, so suitable storage must be ensured! Gluing Formaldehyde class Utilisation class Fire behaviour class Declaration of performance National technical approval Mean density Scarf jointing with melamine resin adhesive (light glued joint), BauBuche S/Q: one surface, Beam BauBuche GL70: top and bottom surface Middle layers: phenolic resin adhesive (dark glued joint) E 1 as per EN 13986 1 and 2 as per EN 1995-1-2 Class E as per EN 13501:2007 + A1:2009 Available in the download area at Laminated veneer lumber made of beech for the construction of bar-shaped and flat load-bearing structures Z-9.1-838 Glued laminated timber made from beech laminated veneer lumber Z-9.1-837 ρ = 740 kg/m³ PAINT COAT/WOOD PROTECTION VARNISH A protective varnish can be applied for transport and installation protection on request. PRE-CUTTING On request SUPERELEVATION Up to 150 mm max. on request
BauBuche S/Q Specifications 07-14 - EN Sheet 9 / 19 Characteristic strength and stiffness values in N/mm 2 and characteristic density in kg / m 3 for Beech LVL with longitudinal layers and Beech LVL with crosswise layers according to the manufacturer s declaration of performance. BauBuche S BauBuche Q Type of load Laminated veneer lumber Laminated veneer lumber Beech LVL with longitudinal layers Beech LVL with crosswise layers Nominal thickness in mm 20 B 80 20 B 80 Strength values Flatwise bending Bending f m,0,k 65 45 Compression f c,90,k 10 10 Shear f v,0,k 8 3.3 Shear (rolling) f v,k not declared 3.3 Edgewise bending Bending a) f m,0,k 70 60 Tension to the grain f t,0,k 60 40 Tension to the grain f t,90,k 1.5 17 Compression to the grain f c,0,k 41.6 24.2 Compression to the grain f c,90,k 14 14 Shear f v,0,k 8 9 Stiffness values Modulus of elasticity E 0,mean 16,800 11,800 Modulus of elasticity E 0,05 14,900 10,700 Modulus of elasticity E 90,mean 470 3,700 Shear modulus, edgewise G mean 760 890 Shear modulus, flatwise G mean 850 430 Density ρ k 680 680 a) Values apply for h 300 mm. For 300 < h 1,000 mm, the characteristic strength must be multiplied by the factor k h =(300/h) 0.12. h is the dimension of the overall cross-section in mm, which is decisive for the bending stress.
Beam BauBuche GL70 Specifications 07-14 - EN Sheet 10 / 19 Characteristic strength, stiffness and density values for glued laminated timber made from beech laminated veneer lumber (BauBuche GL70) Strength class GL 70 Strength values (N/mm²) f m,y,k f m,z,k Characteristic bending strength for flatwise bending stress on the laminations of glued laminated timber 70 a) Characteristic bending strength for edgewise bending stress on the laminations of glued laminated timber 70 f t,0,k Characteristic tensile strength along the grain 55 b) f t,90,k Characteristic tensile strength perpendicular to the grain 1.2 f c,0,k Characteristic compressive strength parallel to the grain 49.5 c), d) f c,90,k Characteristic compressive strength perpendicular to the grain 8.3 c) f v,k Characteristic shear strength 4.0 e) Stiffness values (N/mm²) E 0,mean Mean value of modulus of elasticity along the grain 16,700 E 0,05 5 % percentile value of modulus of elasticity parallel to the grain 15,300 E 90,mean Mean value of modulus of elasticity perpendicular to the grain 470 E 90,05 5 % percentile value of modulus of elasticity perpendicular to the grain 400 G mean Mean value of shear modulus 850 G 05 5 % percentile of shear modulus 760 Density value (kg/m³) ρ k Characteristic density 680 a) For the flatwise bending strength of the laminations of the glued laminated timber, the characteristic strength may be multiplied by the factor k h,m = (600/h) 0.14. h = height of the glued laminated timber cross-section in mm. b) The characteristic compressive strength parallel to the grain may be multiplied by the factor k h,t = (600/h) 0.10. h = larger side length of the glued laminated timber cross-section perpendicular to the longitudinal axis in mm. c) If the glued laminated timber is used exclusively in the environmental conditions of utilisation class 1, the characteristic compressive strength may be increased by the factor 1.2. d) If there are more than three laminations of laminated veneer lumber, the characteristic compressive strength parallel to the grain may be increased by the factor k c,0 = min (0.0009 x h + 0.892; 1.18). h = height of the glued laminated timber cross-section in mm. e) The characteristic shear strength may be multiplied by the factor k h,v = (600/h) 0.25. h = height of the glued laminated timber cross-section in mm.
Board BauBuche S/Q Standard Pack Sizes 07-14 - EN Sheet 11 / 19 Standard width 1850 mm If the ordered volume is more than one pack but less than two, it will be divided into two packs. (Example: standard pack size = 8 pcs. If 10 pcs are ordered, they will be supplied in two packs of 5 pcs each). Pack volume rounded to one decimal. Calculation is made with an accuracy of 3 decimals. 6 m length Thickness Pcs/pack Volume Area Weight (mm) (m 3 ) (m 2 ) (t) 40 8 3.6 88.8 2.6 42 8 3.7 88.8 2.7 60 6 4.0 66.6 2.9 62 6 4.1 66.6 3.0 80 4 3.6 44.4 2.6 82 4 3.6 44.4 2.7 16 m length Thickness Pcs/pack Volume Area Weight (mm) (m 3 ) (m 2 ) (t) 40 3 3.6 88.8 2.6 42 3 3.7 88.8 2.7 60 2 3.6 59.2 2.6 62 2 3.7 59.2 2.7 80 1 2.4 29.6 1.7 82 1 2.4 29.6 1.8 12 m length 40 4 3.6 88.8 2.6 42 4 3.7 88.8 2.7 60 3 4.0 66.6 2.9 62 3 4.1 66.6 3.0 80 2 3.6 44.4 2.6 82 2 3.6 44.4 2.7 18 m length 40 3 4.0 99.9 2.9 42 3 4.2 99.9 3.0 60 2 4.0 66.6 2.9 62 2 4.1 66.6 3.0 80 1 2.7 33.3 1.9 82 1 2.7 33.3 2.0 13.5 m length 40 4 4.0 99.9 2.9 42 4 4.2 99.9 3.1 60 2 3.0 50.0 2.2 62 2 3.1 50.0 2.3 80 2 4.0 50.0 2.9 82 2 4.1 50.0 3.0
Beam BauBuche S Standard Pack Sizes 07-14 - EN Sheet 12 / 19 Unsanded packs contain the same number of beams per pack, but volume and weight are up to 5% higher. If the ordered volume is more than one pack but less than two, it will be divided into two packs. (Example: standard pack size = 80 pcs. If 100 pcs are ordered, they will be supplied in two packs of 50 pcs each). Pack volume rounded to one decimal. Calculation is made with an accuracy of 3 decimals. 6 m 12 m 13.5 m 16 m 40 mm 60 mm 40 mm 60 mm 40 mm 60 mm 40 mm 60 mm 120 160 200 240 280 320 360 400 440 480 520 560 600 Height (mm) 80 56 48 40 32 24 24 24 16 16 16 16 16 Pcs/pack 2.3 2.2 2.3 2.3 2.2 1.8 2.1 2.3 1.7 1.8 2.0 2.2 2.3 Volume [m³] 1.7 1.6 1.7 1.7 1.6 1.3 1.5 1.7 1.2 1.3 1.5 1.6 1.7 Weight [t] 80 56 48 40 32 24 24 24 16 16 16 16 16 Pcs/pack 3.5 3.2 3.5 3.5 3.2 2.8 3.1 3.5 2.5 2.8 3.0 3.2 3.5 Volume [m³] 2.5 1.6 1.7 1.7 1.6 1.3 1.5 1.7 1.2 1.3 1.5 1.6 1.7 Weight [t] 60 42 30 24 24 18 18 18 12 12 12 12 12 Pcs/pack 3.5 3.2 2.9 2.8 3.2 2.8 3.1 3.5 2.5 2.8 3.0 3.2 3.5 Volume [m³] 2.5 2.4 2.1 2.0 2.4 2.0 2.3 2.5 1.9 2.0 2.2 2.4 2.5 Weight [t] 40 28 24 20 16 12 12 12 8 8 8 8 8 Pcs/pack 2.3 2.2 2.3 2.3 2.2 1.8 2.1 2.3 1.7 1.8 2.0 2.2 2.3 Volume [m³] 1.7 1.6 1.7 1.7 1.6 1.3 1.5 1.7 1.2 1.3 1.5 1.6 1.7 Weight [t] 40 28 24 20 16 12 12 12 8 8 8 8 8 Pcs/pack 3.5 3.2 3.5 3.5 3.2 2.8 3.1 3.5 2.5 2.8 3.0 3.2 3.5 Volume [m³] 2.5 2.4 2.5 2.5 2.4 2.0 2.3 2.5 1.9 2.0 2.2 2.4 2.5 Weight [t] 30 21 15 12 12 9 9 9 6 6 6 6 6 Pcs/pack 3.5 3.2 2.9 2.8 3.2 2.8 3.1 3.5 2.5 2.8 3.0 3.2 3.5 Volume [m³] 2.5 2.4 2.1 2.0 2.4 2.0 2.3 2.5 1.9 2.0 2.2 2.4 2.5 Weight [t] 40 28 24 20 16 12 12 12 8 8 8 8 8 Pcs/pack 2.6 2.4 2.6 2.6 2.4 2.1 2.3 2.6 1.9 2.1 2.2 2.4 2.6 Volume [m³] 1.9 1.8 1.9 1.9 1.8 1.5 1.7 1.9 1.4 1.5 1.6 1.8 1.9 Weight [t] 40 28 24 20 16 12 12 12 8 8 8 8 8 Pcs/pack 3.9 3.6 3.9 3.9 3.6 3.1 3.5 3.9 2.9 3.1 3.4 3.6 3.9 Volume [m³] 2.8 2.6 2.8 2.8 2.6 2.3 2.6 2.8 2.1 2.3 2.5 2.6 2.8 Weight [t] 30 21 15 12 12 9 9 9 6 6 6 6 6 Pcs/pack 3.9 3.6 3.2 3.1 3.6 3.1 3.5 3.9 2.9 3.1 3.4 3.6 3.9 Volume [m³] 2.8 2.6 2.4 2.3 2.6 2.3 2.6 2.8 2.1 2.3 2.5 2.6 2.8 Weight [t] 40 28 24 20 16 12 12 12 8 8 8 8 8 Pcs/pack 3.1 2.9 3.1 3.1 2.9 2.5 2.8 3.1 2.3 2.5 2.7 2.9 3.1 Volume [m³] 2.2 2.1 2.2 2.2 2.1 1.8 2.0 2.2 1.6 1.8 1.9 2.1 2.2 Weight [t] 30 21 18 15 12 9 9 9 6 6 6 6 6 Pcs/pack 3.5 3.2 3.5 3.5 3.2 2.8 3.1 3.5 2.5 2.8 3.0 3.2 3.5 Volume [m³] 2.5 2.4 2.5 2.5 2.4 2.0 2.3 2.5 1.9 2.0 2.2 2.4 2.5 Weight [t] 20 14 10 8 8 6 6 6 4 4 4 4 4 Pcs/pack 3.1 2.9 2.6 2.5 2.9 2.5 2.8 3.1 2.3 2.5 2.7 2.9 3.1 Volume [m³] 2.2 2.1 1.9 1.8 2.1 1.8 2.0 2.2 1.6 1.8 1.9 2.1 2.2 Weight [t]
Beam BauBuche GL70 Standard Pack Sizes 07-14 - EN Sheet 13 / 19 Pack volume rounded to one decimal. Calculation is made with an accuracy of 3 decimals. 12 m 13.5 m 120 mm 160 mm 200 mm 240 mm 2 120 mm 160 mm 200 mm 240 mm 2 120 160 200 240 280 320 360 400 440 480 520 560 600 Height (mm) 20 14 12 10 8 6 6 6 4 4 4 4 4 Pcs/pack 2.3 2.2 2.3 2.3 2.2 1.8 2.1 2.3 1.7 1.8 2.0 2.2 2.3 Volume [m³] 1.7 1.6 1.7 1.7 1.6 1.3 1.5 1.7 1.2 1.3 1.5 1.6 1.7 Weight [t] 10 7 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack 1.7 1.6 1.7 1.7 1.6 1.4 1.6 1.7 1.3 1.4 1.5 1.6 1.7 Volume [m³] 1.3 1.2 1.3 1.3 1.2 1.0 1.1 1.3 0.9 1.0 1.1 1.2 1.3 Weight [t] - 7 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack - 2.2 2.3 2.3 2.2 1.8 2.1 2.3 1.7 1.8 2.0 2.2 2.3 Volume [m³] - 1.6 1.7 1.7 1.6 1.3 1.5 1.7 1.2 1.3 1.5 1.6 1.7 Weight [t] - - 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack - - 2.9 2.9 2.7 2.3 2.6 2.9 2.1 2.3 2.5 2.7 2.9 Volume [m³] - - 2.1 2.1 2.0 1.7 1.9 2.1 1.5 1.7 1.8 2.0 2.1 Weight [t] - - - 5 4 3 3 3 2 2 2 2 2 Pcs/pack - - - 3.5 3.2 2.8 3.1 3.5 2.5 2.8 3.0 3.2 3.5 Volume [m³] - - - 2.5 2.4 2.0 2.3 2.5 1.9 2.0 2.2 2.4 2.5 Weight [t] - - - - 4 3 3 3 2 2 2 2 2 Pcs/pack - - - - 3.8 3.2 3.6 4.0 3.0 3.2 3.5 3.8 4.0 Volume [m³] - - - - 2.7 2.4 2.6 2.9 2.2 2.4 2.6 2.7 2.9 Weight [t] 20 14 12 10 8 6 6 6 4 4 4 4 4 Pcs/pack 2.6 2.4 2.6 2.6 2.4 2.1 2.3 2.6 1.9 2.1 2.2 2.4 2.6 Volume [m³] 1.9 1.8 1.9 1.9 1.8 1.5 1.7 1.9 1.4 1.5 1.6 1.8 1.9 Weight [t] 10 7 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack 1.9 1.8 1.9 1.9 1.8 1.6 1.7 1.9 1.4 1.6 1.7 1.8 1.9 Volume [m³] 1.4 1.3 1.4 1.4 1.3 1.1 1.3 1.4 1.0 1.1 1.2 1.3 1.4 Weight [t] - 7 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack - 2.4 2.6 2.6 2.4 2.1 2.3 2.6 1.9 2.1 2.2 2.4 2.6 Volume [m³] - 1.8 1.9 1.9 1.8 1.5 1.7 1.9 1.4 1.5 1.6 1.8 1.9 Weight [t] - - 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack - - 3.2 3.2 3.0 2.6 2.9 3.2 2.4 2.6 2.8 3.0 3.2 Volume [m³] - - 2.4 2.4 2.2 1.9 2.1 2.4 1.7 1.9 2.0 2.2 2.4 Weight [t] - - - 5 4 3 3 3 2 2 2 2 2 Pcs/pack - - - 3.9 3.6 3.1 3.5 3.9 2.9 3.1 3.4 3.6 3.9 Volume [m³] - - - 2.8 2.6 2.3 2.6 2.8 2.1 2.3 2.5 2.6 2.8 Weight [t] - - - - 4 3 3 3 2 2 2 2 2 Pcs/pack - - - - 4.2 3.6 4.1 4.5 3.3 3.6 3.9 4.2 4.5 Volume [m³] - - - - 3.1 2.6 3.0 3.3 2.4 2.6 2.9 3.1 3.3 Weight [t] >>
Beam BauBuche GL70 Standard Pack Sizes 07-14 - EN Sheet 14 / 19 16 m 18 m 120 mm 160 mm 200 mm 240 mm 2 120 mm 160 mm 200 mm 240 mm 2 120 160 200 240 280 320 360 400 440 480 520 560 600 Height (mm) 20 14 12 10 8 6 6 6 4 4 4 4 4 Pcs/pack 3.1 2.9 3.1 3.1 2.9 2.5 2.8 3.1 2.3 2.5 2.7 2.9 3.1 Volume [m³] 2.2 2.1 2.2 2.2 2.1 1.8 2.0 2.2 1.6 1.8 1.9 2.1 2.2 Weight [t] 10 7 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack 2.3 2.2 2.3 2.3 2.2 1.8 2.1 2.3 1.7 1.8 2.0 2.2 2.3 Volume [m³] 1.7 1.6 1.7 1.7 1.6 1.3 1.5 1.7 1.2 1.3 1.5 1.6 1.7 Weight [t] - 7 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack - 2.9 3.1 3.1 2.9 2.5 2.8 3.1 2.3 2.5 2.7 2.9 3.1 Volume [m³] - 2.1 2.2 2.2 2.1 1.8 2.0 2.2 1.6 1.8 1.9 2.1 2.2 Weight [t] - - 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack - - 3.8 3.8 3.6 3.1 3.5 3.8 2.8 3.1 3.3 3.6 3.8 Volume [m³] - - 2.8 2.8 2.6 2.2 2.5 2.8 2.1 2.2 2.4 2.6 2.8 Weight [t] - - - 5 4 3 3 3 2 2 2 2 2 Pcs/pack - - - 3.9 3.6 3.1 3.5 3.9 2.9 3.1 3.4 3.6 3.9 Volume [m³] - - - 2.8 2.6 2.3 2.6 2.8 2.1 2.3 2.5 2.6 2.8 Weight [t] - - - - 4 3 3 3 2 2 2 2 2 Pcs/pack - - - - 5.0 4.3 4.8 5.4 3.9 4.3 4.7 5.0 5.4 Volume [m³] - - - - 3.7 3.1 3.5 3.9 2.9 3.1 3.4 3.7 3.9 Weight [t] 20 14 12 10 8 6 6 6 4 4 4 4 4 Pcs/pack 3.5 3.2 3.5 3.5 3.2 2.8 3.1 3.5 2.5 2.8 3.0 3.2 3.5 Volume [m³] 2.5 2.4 2.5 2.5 2.4 2.0 2.3 2.5 1.9 2.0 2.2 2.4 2.5 Weight [t] 10 7 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack 2.6 2.4 2.6 2.6 2.4 2.1 2.3 2.6 1.9 2.1 2.2 2.4 2.6 Volume [m³] 1.9 1.8 1.9 1.9 1.8 1.5 1.7 1.9 1.4 1.5 1.6 1.8 1.9 Weight [t] - 7 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack - 3.2 3.5 3.5 3.2 2.8 3.1 3.5 2.5 2.8 3.0 3.2 3.5 Volume [m³] - 2.4 2.5 2.5 2.4 2.0 2.3 2.5 1.9 2.0 2.2 2.4 2.5 Weight [t] - - 6 5 4 3 3 3 2 2 2 2 2 Pcs/pack - - 4.3 4.3 4.0 3.5 3.9 4.3 3.2 3.5 3.7 4.0 4.3 Volume [m³] - - 3.2 3.2 2.9 2.5 2.8 3.2 2.3 2.5 2.7 2.9 3.2 Weight [t] - - - 5 4 3 3 3 2 2 2 2 2 Pcs/pack - - - 5.2 4.8 4.1 4.7 5.2 3.8 4.1 4.5 4.8 5.2 Volume [m³] - - - 3.8 3.5 3.0 3.4 3.8 2.8 3.0 3.3 3.5 3.8 Weight [t] - - - - 4 3 3 3 2 2 2 2 2 Pcs/pack - - - - 5.6 4.8 5.4 6.0 4.4 4.8 5.2 5.6 6.0 Volume [m³] - - - - 4.1 3.5 4.0 4.4 3.2 3.5 3.8 4.1 4.4 Weight [t]
BauBuche Panel Standard Pack Sizes 07-14 - EN Sheet 15 / 19 Pack volume rounded to one decimal. Calculation is made with an accuracy of 3 decimals. 120 160 200 440 520 560 640 680 (mm) Thickness 6 m 14 mm 20 mm 25 mm 45 mm 50 mm 60 mm Thickness 12 m 14 mm 20 mm 25 mm 45 mm 50 mm 60 mm 200 160 120 60 40 40 40 40 Pcs/pack 2.0 2.2 2.0 2.2 1.7 1.9 2.2 2.3 Volume [m³] 1.5 1.6 1.5 1.6 1.3 1.4 1.6 1.7 Weight [t] 160 128 96 48 32 32 32 32 Pcs/pack 2.3 2.5 2.3 2.5 2.0 2.2 2.5 2.6 Volume [m³] 1.7 1.8 1.7 1.9 1.5 1.6 1.8 1.9 Weight [t] 80 64 48 24 16 16 16 16 Pcs/pack 1.4 1.5 1.4 1.6 1.2 1.3 1.5 1.6 Volume [m³] 1.1 1.1 1.1 1.2 0.9 1.0 1.1 1.2 Weight [t] 80 64 48 24 16 16 16 16 Pcs/pack 2.6 2.8 2.6 2.9 2.2 2.4 2.8 2.9 Volume [m³] 1.9 2.0 1.9 2.1 1.6 1.8 2.0 2.1 Weight [t] 60 48 36 18 12 12 12 12 Pcs/pack 2.2 2.3 2.2 2.4 1.9 2.0 2.3 2.4 Volume [m³] 1.6 1.7 1.6 1.7 1.4 1.5 1.7 1.8 Weight [t] 40 32 24 12 8 8 8 8 Pcs/pack 1.7 1.8 1.7 1.9 1.5 1.6 1.8 2.0 Volume [m³] 1.3 1.3 1.3 1.4 1.1 1.2 1.3 1.4 Weight [t] 100 80 60 30 20 20 20 20 Pcs/pack 2.0 2.2 2.0 2.2 1.7 1.9 2.2 2.3 Volume [m³] 1.5 1.6 1.5 1.6 1.3 1.4 1.6 1.7 Weight [t] 80 64 48 24 16 16 16 16 Pcs/pack 2.3 2.5 2.3 2.5 2.0 2.2 2.5 2.6 Volume [m³] 1.7 1.8 1.7 1.9 1.5 1.6 1.8 1.9 Weight [t] 40 32 24 12 8 8 8 8 Pcs/pack 1.4 1.5 1.4 1.6 1.2 1.3 1.5 1.6 Volume [m³] 1.1 1.1 1.1 1.2 0.9 1.0 1.1 1.2 Weight [t] 40 32 24 12 8 8 8 8 Pcs/pack 2.6 2.8 2.6 2.9 2.2 2.4 2.8 2.9 Volume [m³] 1.9 2.0 1.9 2.1 1.6 1.8 2.0 2.1 Weight [t] 30 24 18 9 6 6 6 6 Pcs/pack 2.2 2.3 2.2 2.4 1.9 2.0 2.3 2.4 Volume [m³] 1.6 1.7 1.6 1.7 1.4 1.5 1.7 1.8 Weight [t] 20 16 12 6 4 4 4 4 Pcs/pack 1.7 1.8 1.7 1.9 1.5 1.6 1.8 2.0 Volume [m³] 1.3 1.3 1.3 1.4 1.1 1.2 1.3 1.4 Weight [t] >>
BauBuche Panel Standard Pack Sizes 07-14 - EN Sheet 16 / 19 120 160 200 440 520 560 640 680 (mm) Thickness 13.5 m 14 mm 20 mm 25 mm 45 mm 50 mm 60 mm 100 80 60 30 20 20 20 20 Pcs/pack 2.3 2.4 2.3 2.5 2.0 2.1 2.4 2.6 Volume [m³] 1.7 1.8 1.7 1.8 1.4 1.5 1.8 1.9 Weight [t] 80 64 48 24 16 16 16 16 Pcs/pack 2.6 2.8 2.6 2.9 2.2 2.4 2.8 2.9 Volume [m³] 1.9 2.0 1.9 2.1 1.6 1.8 2.0 2.1 Weight [t] 40 32 24 12 8 8 8 8 Pcs/pack 1.6 1.7 1.6 1.8 1.4 1.5 1.7 1.8 Volume [m³] 1.2 1.3 1.2 1.3 1.0 1.1 1.3 1.3 Weight [t] 40 32 24 12 8 8 8 8 Pcs/pack 2.9 3.1 2.9 3.2 2.5 2.7 3.1 3.3 Volume [m³] 2.1 2.3 2.1 2.3 1.8 2.0 2.3 2.4 Weight [t] 30 24 18 9 6 6 6 6 Pcs/pack 2.4 2.6 2.4 2.7 2.1 2.3 2.6 2.8 Volume [m³] 1.8 1.9 1.8 2.0 1.5 1.7 1.9 2.0 Weight [t] 20 16 12 6 4 4 4 4 Pcs/pack 1.9 2.1 1.9 2.1 1.7 1.8 2.1 2.2 Volume [m³] 1.4 1.5 1.4 1.6 1.2 1.3 1.5 1.6 Weight [t]
BauBuche Open-plan kitchen Visualisation open-plan kitchen Wooden beam construction made of BauBuche GL70, staircase, ceiling, kitchen cabinets, table and chairs made of BauBuche panel, pattern of flooring: plait with cube Design: Architekten Hermann Kaufmann ZT GmbH 07-14 - EN Sheet 17 / 19
BauBuche Sports hall 07-14 - EN Sheet 18 / 19 Visualisation sports hall Framework, purlins and columns of Beam BauBuche GL70 / S, stiffening wall panels of Board BauBuche Q Design: Architekten Hermann Kaufmann ZT GmbH
BauBuche Car park 07-14 - EN Visualisation car park Timber structure made of BauBuche used for car park, joists and posts from BauBuche GL70, soffit from BauBuche boards; research project of TUM.Wood with participation of the professors Hermann Kaufmann, Florian Nagler, Stefan Winter, Klaus Richter, Jan-Willem van de Kuilen Sheet 19 / 19