Differential Pressure Control Valve www.ballorex.com
2
Table of contents Chapter Ballorex Delta DHC DN 15-150 1. Safety instructions 4 1.1 Rules/regulations 4 1.2 Intended use 5 1.3 Initial operation 5 1.4 Working on the system 5 1.5 Liability 5 2. Introduction 6 2.1 Description 6 2.2 Benefits 6 2.3 Design 7 2.4 Pressure balancing 8 2.5 With partner valve 8 2.6 Mounting 10 2.7 Operation 11 3. Applications 12 4. Product data sheet 15 4.1 Product finder 15 4.1.1 Ballorex Delta DHC DN 15-150 15 4.1.2 Ballorex Delta DHC DN 15-150 with partner valve 16 4.2 Ballorex Delta DHC DN 15-150 20 4.3 Flow diagrams 23 4.4 Valve sizing 34 4.5 Valve setting DN 15-150 59 5. Accessoires 60 6. Sizing examples 62 6.1 System with Ballorex Delta DHC and Ballorex Venturi 62 6.2 General specifications DN 15-150 64 3
1. Safety instructions Please read the instructions carefully before installation The installation and initial operation of the assembly may be carried out only by an authorised specialist company. Prior to starting work. familiarise yourself with all parts and how they are handled. The application examples in these operating instructions are ideas sketched out. Local laws and regulations have to be observed. Target group: These instructions are intended for authorised specialists exclusively. Work on the heating system. the potable water as well as gas and power network may be carried out by specialists only. Please follow these safety instructions carefully in order to avoid hazards and damage to people and property. 1.1 Rules/regulations Please observe the applicable accident prevention regulations. the environmental legislation and the legal rules for mounting. installation and operation. Moreover. please observe the appropriate guidelines of German standard DIN. EN. DVGW. VDI and VDE (including lightning protection) as well as all current relevant country-specific standards. laws and regulations. Old and newly enforced regulations and standards shall apply. if they are relevant for the individual case. Moreover. the regulations of your local energy supply company have to be observed. Electrical connection: Electrical wiring work may be carried out by qualified electricians only. The VDE regulations and the specifications of the relevant energy supply company have to be met. Excerpt: Installation and construction of heat generators as well as the drinking water heaters: DIN EN 4753. Part 1: Water heater and water heating plants for potable and process water. DIN 18 380: Heating systems and central water heating systems DIN 18 381: Gas. water. waste water installation work within buildings. DIN 18 421: Insulation work on technical plants AV B Wa s V Regulations concerning the general conditions for the supply with water DIN EN 806 ff.: Technical rules for potable water installation DIN 1988 ff.: Technical rules for potable water installation (national addition) DIN EN 1717: Protection of potable water against contaminations DIN 4751: Safety equipment Electrical connection: VDE 0100: Erection of electrical equipment. grounding. protective conductor. potential equalisation conductor. VDE 0701: Repair. modification and testing of electrical devices. VDE 0185: General aspects on the erection of lightning protection systems. VDE 0190: Main potential equalisation of electrical plants. VDE 0855: Installation of antenna plants (shall apply mutatis mutandis). 4
Additional remarks: VDI 6002 Sheet 1: General principles. system technology and use in house building VDI 6002. Sheet 2: Use in students hostels. retirement homes. hospitals. indoor swimming pools and on camping facilities Caution: Prior to any electrical wiring work on pumps and controls. these modules have to be disconnected from voltage correctly. 1.2 Intended use Inexpert installation as well as use for a purpose not intended of the assembly shall rule out all warranty claims. All shut-off valves may be closed by an approved specialist only in case of servicing as otherwise the safety valves are not effective. Do not modify the electrical components. the construction or the hydraulic components! You will impair the safe function of the plant otherwise. 1.3 Initial operation Prior to the initial operation. the plant has to be tested for tightness. correct hydraulic connection as well as accurate and correct electrical connection. In addition. the plant has to be flushed correctly and/as required in keeping with German standard DIN 4753. The initial operation has to be carried out by a trained specialist. which has to be recorded in writing. In addition. the settings have to be put down in writing. The technical documentation has to be available at the device. 1.4 Working on the system The plant has to be de-energised and to be checked for the absence of voltage (such as on the separate fuse or a master switch). Secure the plant against unintentional restart. (If gas is used as fuel. close the gas shut-off valve and secure against unintentional opening.) Repair work on component parts with a safety-relevant function is impermissible. 1.5 Liability We reserve all copyrights for this document. Wrongful use. in particular reproduction and forwarding to third parties shall not be permitted. These installation and operating instructions shall have to be handed to the customer. The executing and/or authorised tradesperson (such as fitter) shall have to explain the function and operation of the plant to the customer in an intelligible manner. 5
2. Introduction Ballorex Delta DHC Differential Pressure Control Valve (DPCV) DN 15-150 1/2-2 2.1 Description The Ballorex Delta DHC is a differential pressure control valve. typically used in district heating and district cooling applications. Ensuring a constant differential pressure across motorized valves or static balancing valves. the Ballorex Delta DHC provides conditions for achieving the correct system distribution. The Ballorex Delta DHC valve eliminates at the same time any noise nuisance caused by high differential pressure across two-way control valves. static valves. or other system components. 2.2 Benefits Wide setting range for different applications: 20-80. 50-150. 100-250. 200-500 System balance ensured regardless of pressure fluctuations Noise problems eliminated Direct installation onto bends and reducers for improved flexibility Robust construction for pressure class PN16 Accurate and easy setting of designed in combination with the Ballorex Venturi or Ballorex Vario Possible to do project handovers in stages due to zone balancing Partial close-downs possible without influencing other parts of the system Easy commissioning saves time and money No overs and unnecessary energy consumption for better thermal comfort 6
2.3 Design The Ballorex Delta DHC is installed either in the supply or the return line. The supply line pressure is received above the diaphragm and the return line pressure underneath the diaphragm. through capillary tubes. One capillary tube is to be connected to the drain of a partner valve like the Ballorex Venturi. Ballorex Vario. or Ballorex Basic. and the other capillary tube to a T-piece. When pressure increases in the system. it also increases above the Ballorex Delta DHC actuator diaphragm. This forces the valve cone downwards. and the valve gradually closes. As a result. a constant pressure drop is obtained across the circuit controlled by the Ballorex Delta DHC. The DN 15-80 valves are single seated. whereas the DN 100-150 valves are double seated. The medium pressure acts onto the bottom and top surfaces of the cone at the same time. In this way. the forces produced by the medium pressure on the cone are compensated the valve cone is pressure balanced. Without the actuator the valve is held in an open position by means of a spring. With force applied on the spindle the valve will close. 7 6 5 4 3 2 1 14 12 11 13 10 9 10 15 16 9 17 8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 - Capillary tube connection - Higher pressure diaphragm chamber - Diaphragm housing - Lower pressure diaphragm chamber - Spring - wheel - Spindle - Valve housing - Valve cone - Locking ring - Nut - Stud bolt - Gasket - Gasket for actuator - Disc - Spring - Valve seat 7
2. Introduction 2.4 Pressure balancing The Ballorex Delta DHC valve is provided with a selection of actuators for different pressure ranges. Depending on the actuator type the Ballorex Delta DHC is factory pre-set at: 50 - actuator 20-80 for DN 15-150 75 - actuator 50-150 for DN 15-150 175 - actuator 100-250 for DN 15-150 350 - actuator 200-500 for DN 15-150 The Ballorex Delta DHC valve is set to a required differential pressure by means of the regulating wheel and a setting tool. By rotating the regulating wheel with a setting tool. any differential pressure. within the control range of each actuator. can be provided. 2.5 With partner valve The Ballorex Delta DHC can be used in combination with a Ballorex Venturi. a Ballorex Vario. or a Ballorex Basic. with drain. as a partner valve. In this case one capillary tube is connected to the coupling installed on the drain of the partner valve and the other to a T-piece in the system. Ballorex Delta DHC in combination with Ballorex Venturi as a partner valve. 8
The pre-setting of the differential pressure is done by rotating the regulating wheel in the Ballorex Delta DHC. The design is set on the Ballorex Venturi or Ballorex Vario using an Allen key. The Ballorex Delta DHC valve can be installed in the return line. The pressure loss across the Ballorex Venturi partner valve, installed in the supply line, is added to the pressure loss in the controlled circuit. When the Ballorex Venturi is installed in the supply line as a partner valve. it is always in the circuit controlled by the Ballorex Delta DHC. In this instance the pressure loss across the Ballorex Venturi is added to the pressure loss in the controlled circuit and needs to be taken into account when setting the Ballorex Delta DHC valve. The Ballorex Delta DHC can be installed in the supply line. The pressure loss across the Ballorex Venturi (partner valve) installed in the return line is not added to the pressure loss in the controlled circuit. When the Ballorex Venturi is installed in the return line and is used as a partner valve it is not in the circuit controlled by the Ballorex Delta DHC valve. Consequently the pressure loss is not taken into account when setting the Ballorex Delta DHC valve installed in the supply line. When the Ballorex Delta DHC valve is installed in combination with a Ballorex Vario or a Ballorex Basic. the pressure loss across the partner valve is not added to the pressure loss in the controlled circuit. provided that the capillary tube is connected to the drain on the outlet side of the partner valve. If the capillary tube is connected to the drain on the inlet side to the partner valve. the pressure loss must be taken into account when setting the Ballorex Delta DHC (see the application examples 5 and 6 for further details). 9
2. Introduction 2.6 Mounting An arrow on the Ballorex Delta DHC valve housing indicates the direction to be respected. The Ballorex Delta DHC can be installed in the return or the supply line. No straight piping before and after the Ballorex Delta DHC is required. The valve can be installed directly at bends. System flushing and pressure testing can be done when the maximum differential pressure setting is provided on the actuator. Maximum test pressure is 16 bar. It is extremely important that both sides of the rubber diaphragm in the actuator are filled with media before start up. If only media has been filled on the upper chamber the pressure can cause severe damage to the diaphragm. After mounting the capillary tubes, the diaphragm chamber has to be vented by loosening the connectors of the capillary tubes. When air is bled and water starts dripping from the capillary tubes, the connectors are tightened. The capillary tubes are to be connected in such a manner that the highest pressure (forward ) is always connected to the diaphragm side where the differential pressure adjustment is made (lower chamber). The lowest pressure (return) is always to be connected to the diaphragm side closest to the valve. To provide the required setting of the Ballorex Delta DHC, the pre-setting wheel is rotated using the setting tool. The differential pressure stabilized by the Ballorex Delta DHC can be verified with the Ballorex Balancing Computer BC2. After connecting one hose to the high pressure port on the Ballorex Venturi (if it is used as a partner valve) and the other hose to the drain valve (provided as an accessory and installed in a T-piece), the Ballorex Balancing Computer BC2 will display the pressure drop in the controlled part of the system. Differential pressure verification is also possible when the Ballorex Delta DHC is combined with the Ballorex Vario or the Ballorex Basic. It is recommended to install isolation valves to be able to service the controlled circuit. During the start-up isolation valves are opened simultaneously slowly and carefully in order to put pressure on both sides of the diaphragm. It is very important to not only put pressure on one side at a time because this will destroy the diaphragm. The differential pressure across the diaphragm must never exceed the set point pressure. 10
2.7 Operation The Ballorex Delta DHC valve is designed for district heating and district cooling systems to ensure a constant differential pressure across the motorized valve controlling through the heat exchanger or in a direct heating system. The stabilization of the differential pressure across the motorized valve improves the temperature control function. The motorized valve opens or closes only in response to the temperature signal from the controlled system and not because of the pressure fluctuation that would trigger changes. The Ballorex Delta DHC provides a constant differential pressure across a motorized valve at a heat exchanger. When the Ballorex Delta DHC is combined with a Ballorex Venturi or a Ballorex Vario. the solution can be used as both a constant pressure regulator and as a maximum limiter. This guarantees that the designed is never exceeded and that the motorized valve is operating with the required authority to provide optimal temperature control. The Ballorex Delta DHC provides a constant differential pressure across a motorized valve in a direct heating system. The Ballorex Delta DHC can be also combined with the Ballorex Basic to ensure constant differential pressure across the motorized valve and to be able to service the controlled part of the system or circuit. The Ballorex Basic can be used for verification provided that the pressure loss across the measuring points of this valve is at least 3.0. When the motorized valve is in a fully open position and the pressure loss across the measuring points of the Ballorex Basic is at least 3.0. the designed can be adjusted by providing the required differential pressure setting on the Ballorex Delta DHC. The motorized valve needs to be correctly sized for this application to operate with the desired authority. 11
3. Applications Application 1 - Temperature control in a heating system with air handling units The Ballorex Delta DHC installed at a heat exchanger in a central heating system will stabilize the differential pressure across the motorized valve. As a result the motorized valve only reacts to the temperature signal and not to pressure fluctuations. The Ballorex Venturi is used as a partner valve to connect the capillary tube and to limit the maximum. The pressure loss across the Ballorex Venturi needs to be taken into account when setting the Ballorex Delta DHC. Application 2 - Temperature control in an air-condition cooling system The Ballorex Delta DHC installed directly in a cooling system will stabilize the differential pressure. By providing stable working conditions the motorized valve only reacts to the temperature signal and not to pressure fluctuations. The Ballorex Venturi is used as a partner valve to connect the capillary tube and to limit the maximum. The pressure loss across the Ballorex Venturi needs to be taken into account when setting the Ballorex Delta DHC. 12
Application 3 - Temperature control in a domestic water system The Ballorex Delta DHC is installed on the primary side of a domestic water system. By stabilizing the differential pressure the desired working conditions for the motorized valve are ensured. The Ballorex Basic can be used as a partner valve to measure the. During commissioning the motorized valve is in a fully open position. When the pressure loss across the measuring points of the Ballorex Basic is at least 3.0, the designed can be verified and adjusted by providing the required differential pressure setting on the Ballorex Delta DHC valve. Application 4 - By-pass across a pump The Ballorex Delta DHC can be used in the pump by-pass (or across supply and return pipes of a circuit). This prevents the pump working against a dead head when all the sub-circuits are closed down. Note: For this application the Ballorex Delta DHC with reverse acting valve needs to be ordered. The valve is provided on request only! 13
3. Applications Application 5 - Ballorex Delta DHC in combination with Ballorex Vario or Ballorex Basic When the Ballorex Vario or the Ballorex Basic is used as a partner valve to the Ballorex Delta DHC, the capillary tube must be connected to the drain installed in the P/T port on the outlet side of the valve. In this instance the pressure loss across the partner valve is not added to the pressure loss in the controlled circuit and thus the Ballorex Delta DHC setting must be equal to the differential pressure required for the controlled circuit only. ΔPdHc = ΔPc Application 6 - Ballorex Delta DHC in combination with Ballorex Vario or Ballorex Basic When the Ballorex Vario or the Ballorex Basic is used as a partner valve to the Ballorex Delta DHC, the capillary tube must be connected to the drain installed in the P/T port on the inlet side of the valve. In this instance the pressure loss across the partner valve is added to the pressure loss in the controlled circuit and the Ballorex Delta DHC setting must be equal to the differential pressure required for the controlled circuit and the pressure loss across the partner valve. ΔPdHc = ΔPc + ΔPbv 14
4. Product data sheet 4.1 Product finder 4.1.1 Ballorex Delta DHC DN 15-150 Ballorex Delta DHC DN 150 DN 125 DN 100 DN 80 DN 65 DN 50 DN 40 DN 32 DN 25 DN 20 DN 15 0 0 0.1 0.2 0.3 0.4 0.6 0.8 1 2 3 4 5 6 8 10 20 30 40 50 60 80 100 200 300 0.36 0.72 1.08 1.44 2.16 2.88 3.6 7.2 10.8 14.418.0 21.6 28.8 36.0 72.0 108 144 180 216 288 360 720 1,080 Flow rate m 3 /h 15
4. Product data sheet 4.1.2 Ballorex Delta DHC DN 15-150 with partner valve Ballorex Venturi as a partner valve to Ballorex Delta DHC DN 50 H DN 40 H DN 25 H & DN 32 H DN 20 H & DN 25 S DN 15 H DN 20 S DN 15 S & DN 20 L DN 15 L 0.005 0.007 0.01 0.02 0.03 0.04 0.06 0.08 0.1 0.2 0.3 0.4 0.5 0.6 0.8 1.0 18.0 25.2 36.0 DN 15 UL 72.0 108.0 144.0 216.0 288.0 360.0 Flow rate 2.0 3.0 4.0 720.0 1080.0 1440.0 1800.02160.0 2880.0 3600.0 7200.0 10800.0 14400.0 DN 300 DN 250 DN 200 DN 150 DN 125 DN 100 DN 80 DN 65 1 2 3 4 5 6 7 8 9 10 20 30 40 50 60 70 80 90 100 200 300 3.6 7.2 10.8 14.4 18.0 21.6 28.8 36.0 72.0 108 144 180 216 288 360 720 1,080 Flow rate m 3 /h 16
Ballorex Vario as a partner valve to Ballorex Delta DHC DN 50 DN 40 DN 32 DN 25 DN 20 0.005 0.007 0.01 0.02 0.03 0.04 0.06 0.08 0.1 0.2 0.3 0.4 0.5 0.6 0.8 1.0 18.0 25.2 36.0 DN 15 72.0 108.0 144 216 288 360 720 1080 1440 1800 2160 2880 3600 7200 10800 14400 2.0 3.0 4.0 Flow rate Ballorex Basic as a partner valve to Ballorex Delta DHC DN 15-50 bar 0.30 0.25 30 25 Pressure drop across valve - ΔPbasic DN 15 DN 20 0.20 20 DN 25 DN 32 DN 40 DN 50 0.15 15 0.10 10 0.05 5 0.00 0 Flow 0.00 1 2 3 4 5 6 7 0 3600 7200 10800 14400 18000 21600 25200 17
4. Product data sheet Flow range Dimension Differential pressures setting range 0.020-0.994 72-3580 DN 15 20-80 0.034-1.267 124-4560 50-150 0.044-1.756 160-6320 100-250 0.063-2.483 226-8940 200-500 0.031-1.564 113-5630 DN 20 DN 20 0.054-1.994 195-7180 50-150 0.070-2.767 252-9960 100-250 0.099-3.914 356-14090 200-500 0.05-2.483 179-8940 DN 25 DN 25 0.086-3.167 310-11400 50-150 0.111-4.392 400-15810 100-250 0.157-6.211 566-22360 200-500 0.079-3.975 286-14310 DN 32 20-80 0.138-5.067 496-18240 50-150 0.178-7.028 640-25300 100-250 0.251-9.939 905-35780 200-500 0.124-6.211 447-22360 DN 40 DN 40 0.215-7.917 775-28500 50-150 0.278-10.981 1000-39530 100-250 0.392-15.528 1410-55900 200-500 0.174-8.694 626-31300 DN 50 DN 50 0.300-11.086 1080-39910 50-150 0.389-15.372 1400-55340 100-250 0.550-21.739 1980-78260 200-500 18
Flow range Dimension Differential pressures setting range 0.289-14.411 1040-51880 DN 65 20-80 0.500-18.369 1800-66130 50-150 0.644-25.475 2320-91710 100-250 0.911-36.025 3280-129690 200-500 0.397-19.875 1430-71550 DN 80 20-80 0.689-25.336 2480-91210 50-150 0.889-35.136 3200-126490 100-250 1.258-49.692 4530-178890 200-500 0.622-31.056 2240-111800 DN 100 20-80 1.075-39.589 3870-142520 50-150 1.389-54.900 5000-197640 100-250 1.964-77.642 7070-279510 200-500 1.069-53.417 3850-192300 DN 125 20-80 1.850-68.094 6660-245140 50-150 2.389-94.428 8600-339940 100-250 3.378-133.542 12160-480750 200-500 1.542-77.019 5550-277270 DN 150 20-80 2.667-98.181 9600-353450 50-150 3.444-136.153 12400-490150 100-250 4.872-192.550 17540-693180 200-500 Differential pressure setting range [] Factory setting [] 20-80 50 50-150 75 100-250 175 200-500 350 19
4. Product data sheet 4.2 Ballorex Delta DHC DN 15-150 Dimensions Specifications temperature 120 C at 16 bar, 150 C at 14 bar, 250 C at 13 bar temperature -20 C diff. pressure 1600 bar pressure 16 bar (PN25 on request) Differential pressure setting range 20-80, 50-150, 100-250, 200-500 Leakage rate Less than 0.05% of Kvs Marking on valve DN, PN, arrow, Kvs, differential pressure setting range, material Connection Flange EN 1092-2 PN16 Valve housing Cast iron EN-GJS-400-15 Seat, cone and spindle Stainless steel Spring W. Nr. 1.4568 powder coated Nuts and bolts 24 CrMo 4/A4 Stag bolt, set point adjuster and spindle housing St. 42, 1.0503 electroplated Diaphragm housing Steel 1.0122 Diaphragm EPDM O-rings EPDM DN A (mm) B (mm) C (mm) D (diameter) (mm) DN 15 130 60 582 220 DN 20 150 65 595 220 DN 25 160 70 601 220 DN 32 180 75 618 220 DN 40 200 85 630 220 DN 50 230 95 660 220 DN 65 290 110 685 220 DN 80 310 155 708 220 DN 100 350 185 625 220 DN 125 400 205 650 220 DN 150 400 240 685 220 20
Valve Article Dimension Nom. Inch DN 15 DN 20 DN 25 DN 32 DN 40 DN 50 Kvs m 3 /h 80597.630 DN 15 ½ 4.0 20-80 ΔP Range [] 80597.631 DN 15 ½ 4.0 50-150 80597.632 DN 15 ½ 4.0 100-250 80597.633 DN 15 ½ 4.0 200-500 80597.634 DN 20 ¾ 6.3 20-80 80597.635 DN 20 ¾ 6.3 50-150 80597.636 DN 20 ¾ 6.3 100-250 80597.637 DN 20 ¾ 6.3 200-500 80597.638 DN 25 1 10 20-80 80597.639 DN 25 1 10 50-150 80597.640 DN 25 1 10 100-250 80597.641 DN 25 1 10 200-500 80597.642 DN 32 1¼ 16 20-80 80597.643 DN 32 1¼ 16 50-150 80597.644 DN 32 1¼ 16 100-250 80597.645 DN 32 1¼ 16 200-500 80597.646 DN 40 1½ 25 20-80 80597.647 DN 40 1½ 25 50-150 80597.648 DN 40 1½ 25 100-250 80597.649 DN 40 1½ 25 200-500 80597.650 DN 50 2 35 20-80 80597.651 DN 50 2 35 50-150 80597.652 DN 50 2 35 100-250 80597.653 DN 50 2 35 200-500 21
4. Product data sheet Valve Article Dimension Nom. Inch DN 65 DN 80 DN 100 DN 125 DN 150 Kvs m 3 /h 80597.654 DN 65 2½ 58 20-80 ΔP Range [] 80597.655 DN 65 2½ 58 50-150 80597.656 DN 65 2½ 58 100-250 80597.657 DN 65 2½ 58 200-500 80597.658 DN 80 3 80 20-80 80597.659 DN 80 3 80 50-150 80597.660 DN 80 3 80 100-250 80597.661 DN 80 3 80 200-500 80597.662 DN 100 4 125 20-80 80597.663 DN 100 4 125 50-150 80597.664 DN 100 4 125 100-250 80597.665 DN 100 4 125 200-500 80597.666 DN 125 5 215 20-80 80597.667 DN 125 5 215 50-150 80597.668 DN 125 5 215 100-250 80597.669 DN 125 5 215 200-500 80597.670 DN 150 6 310 20-80 80597.671 DN 150 6 310 50-150 80597.672 DN 150 6 310 100-250 80597.673 DN 150 6 310 200-500 22
4.3 Flow diagrams The graphs are used to determine the total pressure loss across the Ballorex Delta DHC at the required. DN 15 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 0.5 1.0 1.5 2.0 2.5 0 1800 3600 5400 7200 9000 23
4. Product data sheet DN 20 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 0.5 1.0 1.5 2.0 2.5 0 1800 3600 5400 7200 9000 24
DN 25 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 0 3600 7200 10800 14400 1800 21600 25200 25
4. Product data sheet DN 32 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 0 3600 7200 10800 14400 1800 21600 25200 28800 32400 36000 26
DN 40 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 0 3600 7200 10800 14400 1800 21600 25200 28800 32400 36000 39600 43200 46800 50400 54000 57600 27
4. Product data sheet DN 50 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 22.0 0 7200 14400 21600 28800 36000 43200 50400 57600 64800 72000 79200 28
DN 65 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 0 18000 36000 54000 72000 90000 108000 126000 144000 29
4. Product data sheet DN 80 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0 50.0 0 18000 36000 54000 72000 90000 108000 126000 144000 162000 180000 30
DN 100 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0 50.0 55.0 60.0 65.0 70.0 75.0 80.0 0 18000 36000 54000 72000 90000 108000 126000 144000 162000 180000 198000 216000 234000 252000 270000 288000 31
4. Product data sheet DN 125 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0 110.0 120.0 130.0 140.0 0 36000 72000 108000 144000 180000 216000 252000 288000 324000 360000 396000 432000 468000 504000 32
DN 150 - flange/flange bar 5.00 500 Pressure drop across valve - ΔPdelta dhc 4.75 475 4.50 450 4.25 425 4.00 400 3.75 375 3.50 350 3.25 325 3.00 300 2.75 275 2.50 250 2.25 225 2.00 200 1.75 175 1.50 150 1.25 125 1.00 100 0.75 75 0.50 50 0.25 25 0.00 0 Flow 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 0 36 72 108 144 180 216 252 288 324 360 396 432 468 504 540 576 612 648 684 720 m 3 /h 33
4. Product data sheet 4.4 Valve sizing The available ranges in reference to the required differential pressure setting on the Ballorex Delta DHC valve are specified in the tables. DN 15 - flange/flange 20-80 50-150 100-250 200-500 20 72 1790 22 75 1880 24 78 1960 26 82 2040 28 85 2120 30 88 2190 32 91 2260 34 93 2330 36 96 2400 38 99 2470 40 101 2530 42 104 2590 44 106 2650 46 109 2710 48 111 2770 50 113 2830 52 115 2880 54 118 2940 56 120 2990 58 122 3050 60 124 3100 62 126 3150 64 128 3200 66 130 3250 68 132 3300 70 134 3350 72 136 3390 74 138 3440 76 139 3490 78 141 3530 80 143 3580 50 113 2830 52 115 2880 54 118 2940 56 120 2990 58 122 3050 60 124 3100 62 126 3150 64 128 3200 66 130 3250 68 132 3300 70 134 3350 72 136 3390 74 138 3440 76 139 3490 78 141 3530 80 143 3580 82 145 3620 84 147 3670 86 148 3710 88 150 3750 90 152 3790 92 153 3840 94 155 3880 96 157 3920 98 158 3960 100 160 4000 105 164 4100 110 168 4200 115 172 4290 120 175 4380 125 179 4470 130 182 4560 135 186 4650 140 189 4730 145 193 4820 150 196 4900 100 160 4000 105 164 4100 110 168 4200 115 172 4290 120 175 4380 125 179 4470 130 182 4560 135 186 4650 140 189 4730 145 193 4820 150 196 4900 155 199 4980 160 202 5060 165 206 5140 170 209 5220 175 212 5290 180 215 5370 185 218 5440 190 221 5510 195 223 5590 200 226 5660 205 229 5730 210 232 5800 215 235 5870 220 237 5930 225 240 6000 230 243 6070 235 245 6130 240 248 6200 245 250 6260 250 253 6320 200 226 5660 210 232 5800 220 237 5930 230 243 6070 240 248 6200 250 253 6320 260 258 6450 270 263 6570 280 268 6690 290 272 6810 300 277 6930 310 282 7040 320 286 7160 330 291 7270 340 295 7380 350 299 7480 360 304 7590 370 308 7690 380 312 7800 390 316 7900 400 320 8000 410 324 8100 420 328 8200 430 332 8290 440 336 8390 450 339 8490 460 343 8580 470 347 8670 480 351 8760 490 354 8850 500 358 8940 34
The Ballorex Delta DHC DN 15 can be combined with the Ballorex Venturi DN 15-50 as well as the Ballorex Vario DN 15-50 or the Ballorex Basic DN 15-50 to provide a constant differential pressure in the controlled part of the system. The Ballorex Venturi and the Ballorex Vario combined with the Ballorex Delta DHC also provide the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 0.0076-0.035 27-126 DN 15UL Ballorex Venturi with drain For graphs consult chapter Ballorex Venturi. 0.0172-0.074 62-266 DN 15L 0.036-0.148 130-530 DN 15S 0.074-0.325 270-1700 DN 15H 0.036-0.148 130-530 DN 20L 0.074-0.325 270-1170 DN 20S 0.142-0.603 510-2170 DN 20H 0.142-0.603 510-2170 DN 25S 0.29-1.25 1040-4500 DN 25H 0.29-1.25 1040-4500 DN 32H 0.44-1.88 1580-6760 DN 40H 0.82-3.51 2950-12630 DN 50H 35
4. Product data sheet Partner valve Flow range Dimension Description 0.0054-0.148 19-530 DN 15 Ballorex Vario with drain For graphs consult chapter Ballorex Vario. 0.015-0.325 55-1170 DN 20 0.023-0.603 84-2170 DN 25 0.087-1.25 310-4500 DN 32 0.13-1.88 450-6770 DN 40 0.27-3.51 960-12640 DN 50 Partner valve Kvs Dimension Description m 3 /h 1.80* DN 15 Ballorex Basic with drain For graphs consult chapter Ballorex Basic. 4.65* DN 20 7.40* DN 25 15.5* DN 32 25.7* DN 40 44.0* DN 50 * For quick selection the Ballorex Basic range may be considered equal to the Ballorex Vario range. 36
DN 20 - flange/flange 20-80 50-150 100-250 200-500 20 113 2820 22 118 2950 24 123 3090 26 128 3210 28 133 3330 30 138 3450 32 143 3560 34 147 3670 36 151 3780 38 155 3880 40 159 3980 42 163 4080 44 167 4180 46 171 4270 48 175 4360 50 178 4450 52 182 4540 54 185 4630 56 189 4710 58 192 4800 60 195 4880 62 198 4960 64 202 5040 66 205 5120 68 208 5200 70 211 5270 72 214 5350 74 217 5420 76 220 5490 78 223 5560 80 225 5630 50 178 4450 52 182 4540 54 185 4630 56 189 4710 58 192 4800 60 195 4880 62 198 4960 64 202 5040 66 205 5120 68 208 5200 70 211 5270 72 214 5350 74 217 5420 76 220 5490 78 223 5560 80 225 5630 82 228 5700 84 231 5770 86 234 5840 88 236 5910 90 239 5980 92 242 6040 94 244 6110 96 247 6170 98 249 6240 100 252 6300 105 258 6460 110 264 6610 115 270 6760 120 276 6900 125 282 7040 130 287 7180 135 293 7320 140 298 7450 145 303 7590 150 309 7720 100 252 6300 105 258 6460 110 264 6610 115 270 6760 120 276 6900 125 282 7040 130 287 7180 135 293 7320 140 298 7450 145 303 7590 150 309 7720 155 314 7840 160 319 7970 165 324 8090 170 329 8210 175 333 8330 180 338 8450 185 343 8570 190 347 8680 195 352 8800 200 356 8910 205 361 9020 210 365 9130 215 370 9240 220 374 9340 225 378 9450 230 382 9550 235 386 9660 240 390 9760 245 394 9860 250 398 9960 200 356 8910 210 365 9130 220 374 9340 230 382 9550 240 390 9760 250 398 9960 260 406 10160 270 414 10350 280 422 10540 290 429 10730 300 436 10910 310 444 11090 320 451 11270 330 458 11440 340 465 11620 350 471 11790 360 478 11950 370 485 12120 380 491 12280 390 498 12440 400 504 12600 410 510 12760 420 516 12910 430 523 13060 440 529 13210 450 535 13360 460 540 13510 470 546 13660 480 552 13800 490 558 13950 500 563 14090 37
4. Product data sheet The Ballorex Delta DHC DN 20 can be combined with the Ballorex Venturi DN 20-65 as well as the Ballorex Vario DN 20-50 or the Ballorex Basic DN 20-50 to provide a constant differential pressure in the controlled part of the system. The Ballorex Venturi and the Ballorex Vario combined with the Ballorex Delta DHC also provide the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 0.036-0.148 130-530 DN 20L Ballorex Venturi with drain For graphs consult chapter Ballorex Venturi. 0.074-0.325 270-1170 DN 20S 0.142-0.603 510-2170 DN 20H 0.142-0.603 510-2170 DN 25S 0.29-1.25 1040-4500 DN 25H 0.29-1.25 1040-4500 DN 32H 0.44-1.88 1580-6760 DN 40H 0.82-3.51 2950-12630 DN 50H 0.29-1.25 1040-4500 DN 25H 0.29-1.25 1040-4500 DN 32H 0.44-1.88 1580-6760 DN 40H 0.82-3.51 2950-12630 DN 50H Partner valve Flow range Dimension Description 1.80-7.00 6480-25200 DN 65 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. 38
Partner valve Flow range Dimension Description 0.015-0.325 55-1170 DN 20 Ballorex Vario with drain For graphs consult chapter Ballorex Vario. 0.023-0.603 84-2170 DN 25 0.087-1.25 310-4500 DN 32 0.13-1.88 450-6770 DN 40 0.27-3.51 960-12640 DN 50 Partner valve Kvs Dimension Description m 3 /h 4.65* DN 20 Ballorex Basic with drain For graphs consult chapter Ballorex Basic. 7.40* DN 25 15.5* DN 32 25.7* DN 40 44.0* DN 50 * For quick selection the Ballorex Basic range may be considered equal to the Ballorex Vario range. 39
4. Product data sheet DN 25 - flange/flange 20-80 50-150 100-250 200-500 20 179 4470 22 188 4690 24 196 4900 26 204 5100 28 212 5290 30 219 5480 32 226 5660 34 233 5830 36 240 6000 38 247 6160 40 253 6320 42 259 6480 44 265 6630 46 271 6780 48 277 6930 50 283 7070 52 288 7210 54 294 7350 56 299 7480 58 305 7620 60 310 7750 62 315 7870 64 320 8000 66 325 8120 68 330 8250 70 335 8370 72 339 8490 74 344 8600 76 349 8720 78 353 8830 80 358 8940 50 283 7070 52 288 7210 54 294 7350 56 299 7480 58 305 7620 60 310 7750 62 315 7870 64 320 8000 66 325 8120 68 330 8250 70 335 8370 72 339 8490 74 344 8600 76 349 8720 78 353 8830 80 358 8940 82 362 9060 84 367 9170 86 371 9270 88 375 9380 90 379 9490 92 384 9590 94 388 9700 96 392 9800 98 396 9900 100 400 10000 105 410 10250 110 420 10490 115 429 10720 120 438 10950 125 447 11180 130 456 11400 135 465 11620 140 473 11830 145 482 12040 150 490 12250 100 400 10000 105 410 10250 110 420 10490 115 429 10720 120 438 10950 125 447 11180 130 456 11400 135 465 11620 140 473 11830 145 482 12040 150 490 12250 155 498 12450 160 506 12650 165 514 12850 170 522 13040 175 529 13230 180 537 13420 185 544 13600 190 551 13780 195 559 13960 200 566 14140 205 573 14320 210 580 14490 215 587 14660 220 593 14830 225 600 15000 230 607 15170 235 613 15330 240 620 15490 245 626 15650 250 632 15810 200 566 14140 210 580 14490 220 593 14830 230 607 15170 240 620 15490 250 632 15810 260 645 16120 270 657 16430 280 669 16730 290 681 17030 300 693 17320 310 704 17610 320 716 17890 330 727 18170 340 738 18440 350 748 18710 360 759 18970 370 769 19240 380 780 19490 390 790 19750 400 800 20000 410 810 20250 420 820 20490 430 829 20740 440 839 20980 450 849 21210 460 858 21450 470 867 21680 480 876 21910 490 885 22140 500 894 22360 40
The Ballorex Delta DHC DN 25 can be combined with the Ballorex Venturi DN 25-65 as well as the Ballorex Vario DN 25-50 or the Ballorex Basic DN 25-50 to provide a constant differential pressure in the controlled part of the system. The Ballorex Venturi and the Ballorex Vario combined with the Ballorex Delta DHC also provide the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 0.142-0.603 510-2170 DN 25S Ballorex Venturi with drain For graphs consult chapter Ballorex Venturi. 0.29-1.25 1040-4500 DN 25H 0.29-1.25 1040-4500 DN 32H 0.44-1.88 1580-6760 DN 40H 0.82-3.51 2950-12630 DN 50H Partner valve Flow range Dimension Description 1.80-7.00 6480-25200 DN 65 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. Partner valve Flow range Dimension Description 0.023-0.603 84-2170 DN 25 Ballorex Vario with drain For graphs consult chapter Ballorex Vario. 0.087-1.25 310-4500 DN 32 0.13-1.88 450-6770 DN 40 0.27-3.51 960-12640 DN 50 41
4. Product data sheet Partner valve Kvs Dimension Description m 3 /h 7.40* DN 25 Ballorex Basic with drain For graphs consult chapter Ballorex Basic. 15.5* DN 32 25.7* DN 40 44.0* DN 50 * For quick selection the Ballorex Basic range may be considered equal to the Ballorex Vario range. 42
DN 32 - flange/flange 20-80 50-150 100-250 200-500 20 286 7160 22 300 7500 24 314 7840 26 326 8160 28 339 8470 30 351 8760 32 362 9050 34 373 9330 36 384 9600 38 395 9860 40 405 10120 42 415 10370 44 425 10610 46 434 10850 48 443 11090 50 453 11310 52 462 11540 54 470 11760 56 479 11970 58 487 12190 60 496 12390 62 504 12600 64 512 12800 66 520 13000 68 528 13190 70 535 13390 72 543 13580 74 551 13760 76 558 13950 78 565 14130 80 572 14310 50 453 11310 52 462 11540 54 470 11760 56 479 11970 58 487 12190 60 496 12390 62 504 12600 64 512 12800 66 520 13000 68 528 13190 70 535 13390 72 543 13580 74 551 13760 76 558 13950 78 565 14130 80 572 14310 82 580 14490 84 587 14660 86 594 14840 88 600 15010 90 607 15180 92 614 15350 94 621 15510 96 627 15680 98 634 15840 100 640 16000 105 656 16400 110 671 16780 115 686 17160 120 701 17530 125 716 17890 130 730 18240 135 744 18590 140 757 18930 145 771 19270 150 784 19600 100 640 16000 105 656 16400 110 671 16780 115 686 17160 120 701 17530 125 716 17890 130 730 18240 135 744 18590 140 757 18930 145 771 19270 150 784 19600 155 797 19920 160 810 20240 165 822 20550 170 834 20860 175 847 21170 180 859 21470 185 870 21760 190 882 22050 195 894 22340 200 905 22630 205 916 22910 210 927 23190 215 938 23460 220 949 23730 225 960 24000 230 971 24270 235 981 24530 240 991 24790 245 1000 25040 250 1010 25300 200 905 22630 210 927 23190 220 949 23730 230 971 24270 240 991 24790 250 1010 25300 260 1030 25800 270 1050 26290 280 1070 26770 290 1090 27250 300 1110 27710 310 1130 28170 320 1140 28620 330 1160 29070 340 1180 29500 350 1200 29930 360 1210 30360 370 1230 30780 380 1250 31190 390 1260 31600 400 1280 32000 410 1300 32400 420 1310 32790 430 1330 33180 440 1340 33560 450 1360 33940 460 1370 34320 470 1390 34690 480 1400 35050 490 1420 35420 500 1430 35780 43
4. Product data sheet The Ballorex Delta DHC DN 32 can be combined with the Ballorex Venturi DN 32-80 as well as the Ballorex Vario DN 32-50 or the Ballorex Basic DN 32-50 to provide a constant differential pressure in the controlled part of the system. The Ballorex Venturi and the Ballorex Vario combined with the Ballorex Delta DHC also provide the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 0.29-1.25 1040-4500 DN 32H Ballorex Venturi with drain For graphs consult chapter Ballorex Venturi. 0.44-1.88 1580-6760 DN 40H 0.82-3.51 2950-12630 DN 50H Partner valve Flow range Dimension Description 1.80-7.00 3.5-15.0 6480-25200 12600-54000 DN 65 DN 80 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. Partner valve Flow range Dimension Description 0.087-1.25 310-4500 DN 32 Ballorex Vario with drain For graphs consult chapter Ballorex Vario. 0.13-1.88 450-6770 DN 40 0.27-3.51 960-12640 DN 50 Partner valve Kvs Dimension Description m 3 /h 15.5* DN 32 Ballorex Basic with drain For graphs consult chapter Ballorex Basic. 25.7* DN 40 44.0* DN 50 * For quick selection the Ballorex Basic range may be considered equal to the Ballorex Vario range. 44
DN 40 - flange/flange 20-80 50-150 100-250 200-500 20 447 11180 22 469 11730 24 490 12250 26 510 12750 28 529 13230 30 548 13690 32 566 14140 34 583 14580 36 600 15000 38 616 15410 40 632 15810 42 648 16200 44 663 16580 46 678 16960 48 693 17320 50 707 17680 52 721 18030 54 735 18370 56 748 18710 58 762 19040 60 775 19360 62 787 19690 64 800 20000 66 812 20310 68 825 20620 70 837 20920 72 849 21210 74 860 21510 76 872 21790 78 883 22080 80 894 22360 50 707 17680 52 721 18030 54 735 18370 56 748 18710 58 762 19040 60 775 19360 62 787 19690 64 800 20000 66 812 20310 68 825 20620 70 837 20920 72 849 21210 74 860 21510 76 872 21790 78 883 22080 80 894 22360 82 906 22640 84 917 22910 86 927 23180 88 938 23450 90 950 23720 92 960 23980 94 970 24240 96 980 24490 98 990 24750 100 1000 25000 105 1020 25620 110 1050 26220 115 1070 26810 120 1100 27390 125 1120 27950 130 1140 28500 135 1160 29050 140 1180 29580 145 1200 30100 150 1220 30620 100 1000 25000 105 1020 25620 110 1050 26220 115 1070 26810 120 1100 27390 125 1120 27950 130 1140 28500 135 1160 29050 140 1180 29580 145 1200 30100 150 1220 30620 155 1240 31120 160 1260 31620 165 1280 32110 170 1300 32600 175 1320 33070 180 1340 33540 185 1360 34000 190 1380 34460 195 1400 34910 200 1410 35360 205 1430 35790 210 1450 36230 215 1470 36660 220 1480 37080 225 1500 37500 230 1520 37910 235 1530 38320 240 1550 38730 245 1570 39130 250 1580 39530 200 1410 35360 210 1450 36230 220 1480 37080 230 1520 37910 240 1550 38730 250 1580 39530 260 1610 40310 270 1640 41080 280 1670 41830 290 1700 42570 300 1730 43300 310 1760 44020 320 1790 44720 330 1820 45410 340 1840 46100 350 1870 46770 360 1900 47430 370 1920 48090 380 1950 48730 390 1970 49370 400 2000 50000 410 2020 50620 420 2050 51230 430 2070 51840 440 2100 52440 450 2120 53030 460 2140 53620 470 2170 54200 480 2190 54770 490 2210 55340 500 2240 55900 45
4. Product data sheet The Ballorex Delta DHC DN 40 can be combined with the Ballorex Venturi DN 40-100 as well as the Ballorex Vario DN 40-50 or the Ballorex Basic DN 40-50 to provide a constant differential pressure in the controlled part of the system. The Ballorex Venturi and the Ballorex Vario combined with the Ballorex Delta DHC also provide the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 0.44-1.88 1580-6760 DN 40H Ballorex Venturi with drain For graphs consult chapter Ballorex Venturi. 0.82-3.51 2950-12630 DN 50H Partner valve Flow range Dimension Description 1.80-7.00 3.5-15.0 6480-25200 12600-54000 DN 65 DN 80 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. 6.2-26.0 22300-93600 DN 100 Partner valve Flow range Dimension Description 0.13-1.88 450-6770 DN 40 Ballorex Vario with drain For graphs consult chapter Ballorex Vario. 0.27-3.51 960-12640 DN 50 Partner valve Kvs Dimension Description m 3 /h 25.7* DN 40 Ballorex Basic with drain For graphs consult chapter Ballorex Basic. 44.0* DN 50 * For quick selection the Ballorex Basic range may be considered equal to the Ballorex Vario range. 46
DN 50 - flange/flange 20-80 50-150 100-250 200-500 20 626 15650 22 657 16420 24 686 17150 26 714 17850 28 741 18520 30 767 19170 32 792 19800 34 816 20410 36 840 21000 38 863 21580 40 885 22140 42 907 22680 44 929 23220 46 950 23740 48 970 24250 50 990 24750 52 1010 25240 54 1030 25720 56 1050 26190 58 1070 26660 60 1080 27110 62 1100 27560 64 1120 28000 66 1140 28430 68 1150 28860 70 1170 29280 72 1190 29700 74 1200 30110 76 1220 30510 78 1240 30910 80 1250 31300 50 990 24750 52 1010 25240 54 1030 25720 56 1050 26190 58 1070 26660 60 1080 27110 62 1100 27560 64 1120 28000 66 1140 28430 68 1150 28860 70 1170 29280 72 1190 29700 74 1200 30110 76 1220 30510 78 1240 30910 80 1250 31300 82 1270 31690 84 1280 32080 86 1300 32460 88 1310 32830 90 1330 33200 92 1340 33570 94 1360 33930 96 1370 34290 98 1390 34650 100 1400 35000 105 1430 35860 110 1470 36710 115 1500 37530 120 1530 38340 125 1570 39130 130 1600 39910 135 1630 40670 140 1660 41410 145 1690 42150 150 1710 42870 100 1400 35000 105 1430 35860 110 1470 36710 115 1500 37530 120 1530 38340 125 1570 39130 130 1600 39910 135 1630 40670 140 1660 41410 145 1690 42150 150 1710 42870 155 1740 43570 160 1770 44270 165 1800 44960 170 1830 45630 175 1850 46300 180 1880 46960 185 1900 47610 190 1930 48240 195 1950 48870 200 1980 49500 205 2000 50110 210 2030 50720 215 2050 51320 220 2080 51910 225 2100 52500 230 2120 53080 235 2150 53650 240 2170 54220 245 2190 54780 250 2210 55340 200 1980 49500 210 2030 50720 220 2080 51910 230 2120 53080 240 2170 54220 250 2210 55340 260 2260 56440 270 2300 57510 280 2340 58570 290 2380 59600 300 2420 60620 310 2460 61620 320 2500 62610 330 2540 63580 340 2580 64540 350 2620 65480 360 2660 66410 370 2690 67320 380 2730 68230 390 2760 69120 400 2800 70000 410 2830 70870 420 2870 71730 430 2900 72580 440 2940 73420 450 2970 74250 460 3000 75070 470 3040 75880 480 3070 76680 490 3100 77480 500 3130 78260 47
4. Product data sheet The Ballorex Delta DHC DN 50 can be combined with the Ballorex Venturi DN 50-100 as well as the Ballorex Vario DN 50 or the Ballorex Basic DN 50 to provide a constant differential pressure in the controlled part of the system. The Ballorex Venturi and the Ballorex Vario combined with the Ballorex Delta DE also provide the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 0.82-3.51 2950-12630 DN 50H Ballorex Venturi with drain For graphs consult chapter Ballorex Venturi. Partner valve Flow range Dimension Description 1.80-7.00 3.5-15.0 6480-25200 12600-54000 DN 65 DN 80 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. 6.2-26.0 22300-93600 DN 100 Partner valve Flow range Dimension Description 0.27-3.51 960-12640 DN 50 Ballorex Vario with drain For graphs consult chapter Ballorex Vario. Partner valve Kvs Dimension Description m 3 /h 44.0* DN 50 Ballorex Basic with drain For graphs consult chapter Ballorex Basic. * For quick selection the Ballorex Basic range may be considered equal to the Ballorex Vario range. 48
DN 65 - flange/flange 20-80 50-150 100-250 200-500 20 1040 25940 22 1090 27200 24 1140 28410 26 1180 29570 28 1230 30690 30 1270 31770 32 1310 32810 34 1350 33820 36 1390 34800 38 1430 35750 40 1470 36680 42 1500 37590 44 1540 38470 46 1570 39340 48 1610 40180 50 1640 41010 52 1670 41820 54 1700 42620 56 1740 43400 58 1770 44170 60 1800 44930 62 1830 45670 64 1860 46400 66 1880 47120 68 1910 47830 70 1940 48530 72 1970 49210 74 2000 49890 76 2020 50560 78 2050 51220 80 2080 51880 50 1640 41010 52 1670 41820 54 1700 42620 56 1740 43400 58 1770 44170 60 1800 44930 62 1830 45670 64 1860 46400 66 1880 47120 68 1910 47830 70 1940 48530 72 1970 49210 74 2000 49890 76 2020 50560 78 2050 51220 80 2080 51880 82 2100 52520 84 2130 53160 86 2150 53790 88 2180 54410 90 2200 55020 92 2230 55630 94 2250 56230 96 2270 56830 98 2300 57420 100 2320 58000 105 2380 59430 110 2430 60830 115 2490 62200 120 2540 63540 125 2590 64850 130 2650 66130 135 2700 67390 140 2750 68630 145 2790 69840 150 2840 71040 100 2320 58000 105 2380 59430 110 2430 60830 115 2490 62200 120 2540 63540 125 2590 64850 130 2650 66130 135 2700 67390 140 2750 68630 145 2790 69840 150 2840 71040 155 2890 72210 160 2930 73360 165 2980 74500 170 3020 75620 175 3070 76730 180 3110 77820 185 3160 78890 190 3200 79950 195 3240 80990 200 3280 82020 205 3320 83040 210 3360 84050 215 3400 85040 220 3440 86030 225 3480 87000 230 3520 87960 235 3560 88910 240 3590 89850 245 3630 90780 250 3670 91710 200 3280 82020 210 3360 84050 220 3440 86030 230 3520 87960 240 3590 89850 250 3670 91710 260 3740 93520 270 3810 95300 280 3880 97050 290 3950 98770 300 4020 100460 310 4080 102120 320 4150 103750 330 4210 105360 340 4280 106950 350 4340 108510 360 4400 110050 370 4460 111570 380 4520 113060 390 4580 114540 400 4640 116000 410 4700 117440 420 4750 118860 430 4810 120270 440 4870 121660 450 4920 123040 460 4980 124400 470 5030 125740 480 5080 127070 490 5140 128390 500 5190 129690 49
4. Product data sheet The Ballorex Delta DHC DN 65 can be combined with the Ballorex Venturi DN 65-125 to provide a constant differential pressure in the controlled part of the system as well as to ensure the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 1.80-7.00 3.5-15.0 6480-25200 12600-54000 DN 65 DN 80 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. 6.2-26.0 22300-93600 DN 100 9.0-40.0 32400-144000 DN 125 50
DN 80 - flange/flange 20-80 50-150 100-250 200-500 20 1430 35780 22 1500 37520 24 1570 39190 26 1630 40790 28 1690 42330 30 1750 43820 32 1810 45250 34 1870 46650 36 1920 48000 38 1970 49320 40 2020 50600 42 2070 51850 44 2120 53070 46 2170 54260 48 2220 55430 50 2260 56570 52 2310 57690 54 2350 58790 56 2390 59870 58 2440 60930 60 2480 61970 62 2520 62990 64 2560 64000 66 2600 64990 68 2640 65970 70 2680 66930 72 2720 67880 74 2750 68820 76 2790 69740 78 2830 70650 80 2860 71550 50 2260 56570 52 2310 57690 54 2350 58790 56 2390 59870 58 2440 60930 60 2480 61970 62 2520 62990 64 2560 64000 66 2600 64990 68 2640 65970 70 2680 66930 72 2720 67880 74 2750 68820 76 2790 69740 78 2830 70650 80 2860 71550 82 2900 72440 84 2930 73320 86 2970 74190 88 3000 75050 90 3040 75890 92 3070 76730 94 3100 77560 96 3140 78380 98 3170 79200 100 3200 80000 105 3280 81980 110 3360 83900 115 3430 85790 120 3510 87640 125 3580 89440 130 3650 91210 135 3720 92950 140 3790 94660 145 3850 96330 150 3920 97980 100 3200 80000 105 3280 81980 110 3360 83900 115 3430 85790 120 3510 87640 125 3580 89440 130 3650 91210 135 3720 92950 140 3790 94660 145 3850 96330 150 3920 97980 155 3980 99600 160 4050 101190 165 4110 102760 170 4170 104310 175 4230 105830 180 4290 107330 185 4350 108810 190 4410 110270 195 4470 111710 200 4530 113140 205 4580 114540 210 4640 115930 215 4690 117300 220 4750 118660 225 4800 120000 230 4850 121330 235 4910 122640 240 4960 123940 245 5010 125220 250 5060 126490 200 4530 113140 210 4640 115930 220 4750 118660 230 4850 121330 240 4960 123940 250 5060 126490 260 5160 129000 270 5260 131450 280 5350 133870 290 5450 136240 300 5540 138560 310 5630 140850 320 5720 143110 330 5810 145330 340 5900 147510 350 5990 149670 360 6070 151790 370 6160 153880 380 6240 155950 390 6320 157990 400 6400 160000 410 6480 161990 420 6560 163950 430 6640 165890 440 6710 167810 450 6790 169710 460 6860 171580 470 6940 173440 480 7010 175270 490 7080 177090 500 7160 178890 51
4. Product data sheet The Ballorex Delta DHC DN 80 can be combined with the Ballorex Venturi DN 80-150 to provide a constant differential pressure in the controlled part of the system as well as to ensure the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 3.5-15.0 6.2-26.0 12600-54000 22300-93600 DN 80 DN 100 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. 9.0-40.0 32400-144000 DN 125 16.8-57.0 60480-205200 DN 150 52
DN 100 - flange/flange 20-80 50-150 100-250 200-500 20 2240 55900 22 2350 58630 24 2450 61240 26 2550 63740 28 2650 66140 30 2740 68470 32 2830 70710 34 2920 72890 36 3000 75000 38 3080 77060 40 3160 79060 42 3240 81010 44 3320 82920 46 3390 84780 48 3460 86600 50 3540 88390 52 3610 90140 54 3670 91860 56 3740 93540 58 3810 95200 60 3870 96820 62 3940 98430 64 4000 100000 66 4060 101550 68 4120 103080 70 4180 104580 72 4240 106070 74 4300 107530 76 4360 108970 78 4420 110400 80 4470 111800 50 3540 88390 52 3610 90140 54 3670 91860 56 3740 93540 58 3810 95200 60 3870 96820 62 3940 98430 64 4000 100000 66 4060 101550 68 4120 103080 70 4180 104580 72 4240 106070 74 4300 107530 76 4360 108970 78 4420 110400 80 4470 111800 82 4530 113190 84 4580 114560 86 4640 115920 88 4690 117260 90 4740 118590 92 4800 119900 94 4850 121190 96 4900 122470 98 4950 123740 100 5000 125000 105 5120 128090 110 5240 131100 115 5360 134050 120 5480 136930 125 5590 139750 130 5700 142520 135 5810 145240 140 5920 147900 145 6020 150520 150 6120 153090 100 5000 125000 105 5120 128090 110 5240 131100 115 5360 134050 120 5480 136930 125 5590 139750 130 5700 142520 135 5810 145240 140 5920 147900 145 6020 150520 150 6120 153090 155 6220 155620 160 6320 158110 165 6420 160570 170 6520 162980 175 6610 165360 180 6710 167710 185 6800 170020 190 6890 172300 195 6980 174550 200 7070 176780 205 7160 178970 210 7250 181140 215 7330 183290 220 7420 185400 225 7500 187500 230 7580 189570 235 7660 191620 240 7750 193650 245 7830 195660 250 7910 197640 200 7070 176780 210 7250 181140 220 7420 185400 230 7580 189570 240 7750 193650 250 7910 197640 260 8060 201560 270 8220 205400 280 8370 209170 290 8510 212870 300 8660 216510 310 8800 220090 320 8940 223610 330 9080 227070 340 9220 230490 350 9350 233850 360 9490 237170 370 9620 240440 380 9750 243670 390 9870 246860 400 10000 250000 410 10120 253110 420 10250 256170 430 10370 259210 440 10490 262200 450 10610 265170 460 10720 268100 470 10840 270990 480 10950 273860 490 11070 276700 500 11180 279510 53
4. Product data sheet The Ballorex Delta DHC DN 100 can be combined with the Ballorex Venturi DN 100-200 to provide a constant differential pressure in the controlled part of the system as well as to ensure the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 6.2-26.0 9.0-40.0 22300-93600 32400-144000 DN 100 DN 125 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. 16.8-57.0 60480-205200 DN 150 28.0-100 101000-360000 DN 200 54
DN 125 - flange/flange 20-80 50-150 100-250 200-500 20 3850 96150 22 4030 100840 24 4210 105330 26 4390 109630 28 4550 113770 30 4710 117760 32 4860 121620 34 5010 125370 36 5160 129000 38 5300 132530 40 5440 135980 42 5570 139340 44 5700 142610 46 5830 145820 48 5960 148960 50 6080 152030 52 6200 155040 54 6320 157990 56 6440 160890 58 6550 163740 60 6660 166540 62 6770 169290 64 6880 172000 66 6990 174670 68 7090 177290 70 7200 179880 72 7300 182430 74 7400 184950 76 7500 187430 78 7600 189880 80 7690 192300 50 6080 152030 52 6200 155040 54 6320 157990 56 6440 160890 58 6550 163740 60 6660 166540 62 6770 169290 64 6880 172000 66 6990 174670 68 7090 177290 70 7200 179880 72 7300 182430 74 7400 184950 76 7500 187430 78 7600 189880 80 7690 192300 82 7790 194690 84 7880 197050 86 7980 199380 88 8070 201690 90 8160 203970 92 8250 206220 94 8340 208450 96 8430 210660 98 8510 212840 100 8600 215000 105 8810 220310 110 9020 225490 115 9220 230560 120 9420 235520 125 9620 240380 130 9810 245140 135 9990 249810 140 10180 254390 145 10360 258890 150 10530 263320 100 8600 215000 105 8810 220310 110 9020 225490 115 9220 230560 120 9420 235520 125 9620 240380 130 9810 245140 135 9990 249810 140 10180 254390 145 10360 258890 150 10530 263320 155 10710 267670 160 10880 271960 165 11050 276170 170 11210 280330 175 11380 284420 180 11540 288450 185 11700 292430 190 11850 296360 195 12010 300230 200 12160 304060 205 12310 307830 210 12460 311560 215 12610 315250 220 12760 318900 225 12900 322500 230 13040 326060 235 13180 329590 240 13320 333080 245 13460 336530 250 13600 339940 200 12160 304060 210 12460 311560 220 12760 318900 230 13040 326060 240 13320 333080 250 13600 339940 260 13870 346680 270 14130 353280 280 14390 359760 290 14650 366130 300 14900 372390 310 15140 378550 320 15380 384600 330 15620 390570 340 15860 396440 350 16090 402230 360 16320 407930 370 16540 413560 380 16760 419110 390 16980 424590 400 17200 430000 410 17410 435340 420 17620 440620 430 17830 445830 440 18040 450990 450 18240 456080 460 18440 461120 470 18640 466110 480 18840 471040 490 19040 475920 500 19230 480750 55
4. Product data sheet The Ballorex Delta DHC DN 125 can be combined with the Ballorex Venturi DN 125-250 to provide a constant differential pressure in the controlled part of the system as well as to ensure the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 9.0-40.0 16.8-57.0 32400-144000 60480-205200 DN 125 DN 150 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. 28.0-100 101000-360000 DN 200 41.0-157 148000-565000 DN 250 56
DN 150 - flange/flange 20-80 50-150 100-250 200-500 20 5550 138640 22 5820 145400 24 6070 151870 26 6320 158070 28 6560 164040 30 6790 169790 32 7010 175360 34 7230 180760 36 7440 186000 38 7640 191100 40 7840 196060 42 8040 200900 44 8230 205630 46 8410 210250 48 8590 214770 50 8770 219200 52 8940 223540 54 9110 227800 56 9280 231980 58 9440 236090 60 9600 240120 62 9760 244090 64 9920 248000 66 10070 251850 68 10230 255630 70 10370 259360 72 10520 263040 74 10670 266670 76 10810 270250 78 10950 273780 80 11090 277270 50 8770 219200 52 8940 223540 54 9110 227800 56 9280 231980 58 9440 236090 60 9600 240120 62 9760 244090 64 9920 248000 66 10070 251850 68 10230 255630 70 10370 259360 72 10520 263040 74 10670 266670 76 10810 270250 78 10950 273780 80 11090 277270 82 11230 280720 84 11360 284120 86 11500 287480 88 11630 290810 90 11760 294090 92 11890 297340 94 12020 300560 96 12150 303740 98 12280 306880 100 12400 310000 105 12710 317660 110 13010 325130 115 13300 332440 120 13580 339590 125 13860 346590 130 14140 353450 135 14410 360190 140 14670 366800 145 14930 373290 150 15190 379670 100 12400 310000 105 12710 317660 110 13010 325130 115 13300 332440 120 13580 339590 125 13860 346590 130 14140 353450 135 14410 360190 140 14670 366800 145 14930 373290 150 15190 379670 155 15440 385950 160 15680 392120 165 15930 398200 170 16170 404190 175 16400 410090 180 16640 415910 185 16870 421650 190 17090 427310 195 17320 432890 200 17540 438410 205 17750 443850 210 17970 449230 215 18180 454550 220 18390 459800 225 18600 465000 230 18810 470140 235 19010 475220 240 19210 480250 245 19410 485230 250 19610 490150 200 17540 438410 210 17970 449230 220 18390 459800 230 18810 470140 240 19210 480250 250 19610 490150 260 19990 499860 270 20380 509380 280 20750 518730 290 21120 527910 300 21480 536940 310 21830 545810 320 22180 554540 330 22530 563140 340 22860 571610 350 23200 579960 360 23530 588180 370 23850 596300 380 24170 604300 390 24490 612200 400 24800 620000 410 25110 627700 420 25410 635310 430 25710 642830 440 26010 650260 450 26300 657610 460 26600 664880 470 26880 672060 480 27170 679180 490 27450 686210 500 27730 693180 57
4. Product data sheet The Ballorex Delta DHC DN 150 can be combined with the Ballorex Venturi DN 150-300 to provide a constant differential pressure in the controlled part of the system as well as to ensure the option of limiting the maximum. See the application examples for further details. Partner valve Flow range Dimension Description 16.8-57.0 28.0-100 60480-205200 101000-360000 DN 150 DN 200 Ballorex Venturi with drain (provided as an accessory) For graphs consult chapter Ballorex Venturi. 41.0-157 148000-565000 DN 250 72.0-226 259000-814000 DN 300 58
4.5 Valve setting DN 15-150 The Ballorex Delta DHC valve is provided with four differential pressure setting ranges. The differential pressure setting is done turning a regulating wheel operated by a setting tool. Differential pressure setting range Factory setting 20-80 50 50-150 75 100-250 175 200-500 350 Other settingsfactory setting To provide any other setting on the Ballorex Delta DHC valve, the regulating wheel must be rotated using a setting tool. The rotations of the regulating wheel change the spring compression and thus the force counteracting the force produced by the pressure in the membrane chamber. Each time the regulating wheel is rotated, a new force equilibrium is obtained ensuring the desired differential pressure in the controlled circuit. In order to control the setting, pressure gauges must be installed in the supply and the return lines. The differential pressure can be also checked with the Ballorex Balancing Computer BC2 provided that the medium temperature does not exceed 90 C. The balancing computer must be connected to the measuring point on a partner valve and to a measuring point installed in the pipe inside the controlled loop of the Ballorex Delta DHC valve. The Ballorex Delta DHC is provided with two capillary tubes for installation in the supply or the return line. The valve does not provide the shut-off function. It is therefore recommended to install isolation valves in the system. 59
5. Accessoires Accessories Article Dimension Description 80597.530 DN 15UL Ballorex Venturi with Combi Drain Midi 80597.531 DN 15L 80597.532 DN 15S 80597.533 DN 15H 80597.534 DN 20L 80597.535 DN 20S 80597.536 DN 20H 80597.537 DN 25S 80597.538 DN 25H 80597.539 DN 32H 80597.540 DN 40H 80597.541 DN 50H 80597.706 DN 15 Ballorex Vario with Combi Drain Midi 80597.707 DN 20 80597.708 DN 25 80597.709 DN 32 80597.710 DN 40 80597.711 DN 50 60
Accessories Article Dimension Description 80597.726 DN 15 Ballorex Basic with drain 80597.727 DN 20 80597.728 DN 25 80597.729 DN 32 80597.730 DN40 80597.731 DN 50 80597.471 80597.472 DN 65 DN 80 Ballorex Venturi - When used as a partner valve a Combi Drain Maxi for capillary tube connection is required. The drain is provided as an accessory to 80597.473 DN 100 be ordered separately 80597.474 DN 125 80597.475 DN 150 80597.476 DN 200 80597.477 DN 250 80597.478 DN 300 80597.0204 R 1/4 connection 3/8 UNF measuring point G 3/4 drain Combi Drain Maxi - drain with measuring point for Ballorex Venturi DN 65-600. The capillary tube from the Ballorex Delta DHC is connected to the R 1/4 coupling delivered along with the Combi Drain Maxi and installed on the drain 80597.0210 R ¼ A coupling installed on the drain of the Ballorex Venturi, the Ballorex Vario or the Ballorex Basic DN 15-50 to connect the capillary tube with R 1/4 connector from the Ballorex Delta DHC On request 1.0 m, Ø 4 mm Capillary tube with ¼ connector 61