Chassis panelwork is all In House manufactured from nominally 1.2mm Galvanised steel. Where at all possible, flanges are formed inward facing to prevent exposure to bare metal edges. Sufficient forms and folds are incorporated to provide a vibration free, robust structure. The panel work is jointed throughout using 3/16 Polygrip self adjusting and air tight rivets. Access is provided through a single panel. This covers the fan and motor sets, the coil and condensate tray do not require the removal of any panels. The fan access hooks in place on a front lip and swings closed. This is then retained by machine screws into captive Nutserts. The coil / condensate tray assembly is retained again by Machine Screws into 'Nutserts'. Fans are direct drive, double inlet, forward curved centrifugal type. oth the impellors & impellor housings are of galvanised steel. Fan & motor assemblies are mounted separately to the fan deck assembly using M6 Machine screws into captive Nutserts and can be removed individually for non routine servicing or replacement. Each fan is connected to the fan wiring loom by terminal strip. Motor & impellor assemblies are statically and dynamically balanced in twin planes. Motors are totally enclosed, external rotor, permanent split capacitor type. Power factor shall be 0.9 or better. earings are sealed for life ball race type with a manufacturers minimum life expectancy of,000 hours under typical operating conditions. Overload protection is afforded to each individual motor by an auto resetting thermal contactor. Motor insulation is to class with the enclosure to IP. Supply 2V 1Ph. Speed Control is by multi-tapped transformer. 18 speed outputs are available and 9 selected outputs are wired for on site adjustment. Controls are fed from an additional VA V output. More detail about our speed control method is given on the last page of this data sheet. Coils are manufactured from seamless 3/8 copper tube, mechanically expanded onto aluminium fins. Fins are punched with die formed collars to afford maximum heat transfer surface area with the tubes. All coils are circuited for maximum output and from bottom to top, optimising output and ensuring free venting and draining. Vents and drains are slotted type. Coils are unhanded but not interchangeable. Handings notated against direction of airflow. Coil terminations are 15mm dia plain copper at mm centres through an aluminium support plate for rigidity. Every coil is leak tested using dry air under water to bar. Pressure drop details are given on page 6 of this data sheet. The Condensate Tray covers the entire coil and valve assembly area and has a positive fall to the 15mm drain point. The pan is manufactured from galvanised steel, corners are brazed and the termination is silver soldered into position. Each pan additionally incorporates a pressure normalising external cover. Stainless steel pans are available as an option. Insulation is used throughout for both thermal and acoustic damping. Insulation is open cell, class O, CFC and HFC free expanded foam. Foam complies with CAA airport and London orough flammability and toxicity requirements. Adhesive has light, ageing and temperature tolerance. Spigots as standard, are circular 0mm or 2mm dia. manufactured from galvanised steel. These are screw fixed to the front of the fan coil unit in the positions indicated. Unused spigot connections are capped off but remain available for use if layout changes occur. End spigot connections can be provided on request. Rectangular spigots are also available if requested. Controls Enclosure All controls are, as standard, fitted to a control back plate which is located on the side of the fan coil. The electrical cover then encloses the controls and gives access from both the side and below. The whole electrical assembly including switches is mounted on the side of the fan coil unit alongside the coil terminations and valve assembly. Control Valves are modulating 4 port via a stand alone controller. Standard return air sensors are bead type for mounting in the return air path. Room located sensor/set point adjustment/fan speed control is optional. The standard valve assembly (and any free issued valves) should terminates in 15mm or mm copper compression fittings at mm centres. Filters are EU2 or EU3 media secured to a wire metal frame, easily removable for routine maintenance, cleaning or replacement. Other types are available. 2
TROJAN 2 7 0 SPIGOTS (0 & 2) AND SPIGOT LANKS WILL ALWAYS E FITTED AS SHOWN. PROVISION FOR SIDE SPIGOTS WILL E PROVIDED ONLY IF REQUESTED. SPIGOTS AND COVERS CAN E CHANGED TO SUIT SITE REQUIREMENTS. EXTRA SPIGOTS AND COVERS CAN E SUPPLIED IF REQUESTED. ALL SPIGOTS, ROUND AND RECTANGULAR ARE mm DEEP. SIZE A 1 SIZE 0 & 2 5 SIZE 0 RECTANGULAR SPIGOT OPTION 3 0 SIZE 0 0 0 SIZE - 0mm SIZE 0 / 2-700mm SIZE 0-0mm SIZE 0-10mm SIZE 0 / 0-10mm SIZE 0-1900mm SIZE 0 & 0 3 4 0 0 0 3 4 FCU SIZE 0 & 2 0 0 0 & 0 0 Dim'n Dim'n WEIGHT 'A' '' Kg 805 1105 15 1705 05 7 887 1187 17 1787 87 & 66 82 93 & 97 105 SIZE 0 0 0 0 3 4 5 0 0 0 0 Hanging Centres 8 mm Dim'n 'A' = Overal Width FILTER SECTION Hanging Centres - Dim'n '' Hanging Centres '' + mm LEFT HAND UNIT AIR FLOW C H C H RIGHT HAND UNIT H C DIRECTION OF AIR FLOW 0 O/A Centres Return Flow Condensate 1 1 193 C H Electrics & Controls Enclosure Main Access Panel 900 Do Not Scale LEFT HAND UNIT SHOWN - RIGHT HAND UNIT OPPOSITE AILITY UNITS HANDED AGAINST THE AIR FLOW DIMENSIONS 3
DISCHARGE SOUND POWER 1 2 0 1k 2k 4k 8 ACOUSTICS Acoustic Selection Guide 15 17 15 The noise figures shown are for a unit operating against Pa with sufficient duct connections to keep in duct air velocities at or below 2.5m/s. As a guide, for each additional 10Pa external resistance the Sound Power figures will increase by 1 to 1.5d The inlet Sound Power figures are as measured. Introducing an inlet plenum box will reduce the inlet sound power figures by at least 2-3d. The discharge figures have been factored to allow for ductwork, a plenum and grille. Please refer to the bottom of this column for the factors used. Reducing the lowest fan speed using the fine trimming device will lower the Ultra Low SWL. NR levels can only be used as a guide as they cannot be accurate for every office environment. An evaluation must be undertaken by an acoustician to reliably ascertain the final NR levels in the air conditioned space. Independent test data to qualify the SWL s and the discharge factors shown below is available from the office upon request. 14 16 13 12 10 18 14 11 19 15 DISCHARGE FACTORS 1 2 0 1 k 2 k 4 k 8 k -5-5 -5-9 -12-12 -12-3 16 ( SWL ) d REF 10-12 w 4
INLET SOUND POWER 1 2 0 1k 2k 4k 8 NR AC FULL LOAD AMPS AC START AMPS 17 0.15 0. 0. 0. 0. 0. 0.66 0.90 1.11 1. 16 0 0.15 0. 0. 0.66 0. 0.90 0. 1.11 0. 1. 2 0. 0. 0. 0.74 0.92 0.87 1. 1.77 2. 2.76 0 0. 0. 0.87 1. 0. 1.77 0.74 2. 0.92 2.76 62 0 0. 0.65 0.89 1.11 1. 1. 2.67 3. 4.14 0 0. 0.65 1. 0.89 2.67 1.11 3. 1. 4.14 0 0. 1. 1. 1.84 2.64 3. 4. 5. 62 64 0 0.75 1. 1.85 2. 2. 3. 4. 5. 6.90 ( SWL ) d REF 10-12 w 5
COOLING DUTY - PERFORMANCE The cooling duties are based on Pa external resistance, Summer Entering Air at o C db - % RH and the heating duties are based on Winter Entering Air at o C. Cooling are the maximum available. Leaving air temperature or pressure drop constraints may reduce outputs. HYDRAULIC PRESSURE DROPS NEW NEW ( KNOWN FLOW) 2 PRESS X DROP = 4 ROW COOLING COIL 1 ROW HEATING COIL SIZE 0 SIZE 0 SIZE 0 / 0 SIZE 0 FLOW L/S FLOW L/S SIZE 0 / 2 0.05 3.05 0.08 0.10 0.10 0.10 KNOWN PRESS DROP KPa SIZE 0.10 13.05 SIZE 0 / 2 0.15 13.97 SIZE 0 SIZE 0 0. 0. 13.14 13. SIZE 0 / 0 0.. SIZE 0 0..99 KPa SIZE 0.05 2. 9.66 18.00 6.00 6. 1. 1.64 2.07 2. 0.97 1. 2. 2.66 1. 2. 3. 4.01 4.77 2.64 3. 4. 5. 2. 3.72 5. 6.17 7. 2.85 4. 5.84 7.03 8. 1.04 1. 2. 2.88 1.16 2.71 3.16 1.89 2.84 3.88 4.77 5.88 3.14 4. 5. 6. 3.09 4. 6. 7. 8.64 3. 5.11 6.95 8. 9.77 0.82 1.18 1. 1.92 2. 0.91 1. 2.12 2. 1. 2. 3.04 3.72 4. 2. 3. 4. 5.02 2. 3. 4.86 5.75 6.75 2.65 4.00 5. 6. 7.64 0.96 1. 1.79 2. 2.65 1.06 1. 2. 2.91 1.74 2. 3. 4. 5. 2.89 3.95 5.00 5.91 2.84 4.07 5.71 6.76 7.94 3.12 4.70 6. 7.70 8.99 0.77 1.13 1. 1.83 0.86 1. 1. 2.01 2. 1. 2.11 2.89 3. 4. 1. 2. 3. 4.04 4.77 2. 3. 4.62 5. 6. 2. 3.80 5.17 6. 7. 0.85 1. 1. 2.01 2. 0.94 1. 1.75 2. 2. 1. 2. 3.17 3.90 4.64 1.75 2. 3. 4. 5. 2. 3.62 5.07 6.00 7.05 2.77 4.18 5.68 6.84 7.98 0. 1.13 1. 0.67 0.97 1. 1. 1.84 1.65 2. 2.78 3. 1. 1.83 2. 3.16 3.73 2. 3. 4. 5.02 2.97 4.04 4.87 5.68 0. 1.13 1. 0.67 0.97 1. 1. 1.84 1.65 2. 2.78 3. 1. 1.83 2. 3.16 3.73 2. 3. 4. 5.02 2.97 4.04 4.87 5.68 Direct Current FCUs The Trojan fan coil units illustrated in this catalogue are also available in Direct Current (DC) motor versions. These reduce electrical loads by 65-75%, have infinite speed conrtrol effected by a 0-10v signal, they give off no motor heat and last twice as long as their AC equivelants. 6 Chilled Water Temp F&R 3. 5. 6.79 8.19 9. 4. 6. 8. 9.91 11. 4.07 6. 8.09 9.76 11. 5. 7.84 9.85 1 13.66 3.18 4.88 6. 7. 8.86 4. 6.13 7.70 9. 10.67 3.74 5.75 7. 8.97 10. 5.07 7. 9.06 10.85 12.65 3.03 4.65 6.01 7. 8. 4.10 5.83 7. 8.77 10.15 3. 5.10 6. 7.97 9. 4. 6. 8.04 9.64 11.15 2. 3.64 4.70 5.67 6. 3. 4. 5.73 6.86 7.94 2. 3.64 4.70 5.67 6. 3. 4. 5.73 6.86 7.94 5.5 O C/11 O C 6 O C/12 O C 8 O C/12 O C 11 O C/15 O C
HEATING DUTY - AIR VOLUMES L/S 82 O C/71 O C O C/ O C O C/ O C 10Pa Pa Pa Pa Pa 1. 1. 1.81 1.99 0.81 1.00 1. 1. 0. 0.71 0.78 0.85 0.93 65 95 111 1 1 85 107 1 1 80 103 1 1 75 97 1 1 70 93 1 1 1. 1.76 2.11 2. 0.95 1.16 1. 1. 1. 0.67 0.82 0.91 0.99 1.09 0 77 110 1 1 172 66 94 118 1 169 88 113 1 167 83 107 1 165 77 102 1 1 2.05 2. 2.95 3. 3. 1. 1.73 1.94 2. 0.96 1. 1. 1. 2 1 170 8 0 0 115 1 2 2 6 1 5 2 0 91 1 198 2 6 77 1 190 2 9 2. 2.98 3. 3.69 4.06 1. 2. 2. 2.68 1.09 1. 1. 1.73 1.90 0 1 194 2 7 3 1 179 2 0 3 113 166 7 7 3 101 1 2 2 3 85 1 9 2 8 3. 4. 4.98 5. 6.02 2. 2.95 3. 3. 3.97 2.09 2. 2. 2.82 0 0 0 4 8 0 180 2 3 5 7 1 2 8 8 6 1 2 5 8 4 1 2 0 4 0 3.88 4.86 5. 5.95 6. 2. 3. 3. 3.93 4. 1.82 2. 2. 2.78 3.06 0 6 8 2 8 7 199 0 2 3 6 179 0 7 2 6 1 2 3 1 5 1 2 2 5 5 4. 5.65 6. 6.99 7.68 2.93 3.73 4.17 4. 5.07 2.08 2.64 2.96 3. 3. 0 9 9 5 7 6 2 3 3 0 2 5 3 7 5 8 191 5 3 0 5 174 0 0 6 0 5. 7.06 7.71 8. 9. 3. 4.66 5.09 5.64 6. 2. 3. 3. 4.00 4. 0 3 6 4 6 7 9 4 5 6 7 1 4 0 6 7 0 0 0 7 708 2 7 1 9 690 7
USEFUL INFORMATION Speed Control. Every fan coil is supplied with a speed controlling transformer incorporating 6 speed tappings. Ability will wire each fan coil to the 3 speeds selected as the most appropriate for your project. Notwithstanding this, on site changes can be made if another set of speeds is felt more suitable for a particular area. Each fixed speed is additionally complemented with two fine adjustments. These are effected by adjusting the fine tune three position switch. The fine tune at setting one gives the selected speed unmodified with the two other fine tune settings giving two reductions on the main speed set. SETTING TRIMMER SETTING CONTROL ST'D LOW EXTRA LOW ULTRA LOW A OOST AOVE THOSE SHOWN IS AVAILALE AT MED MED - 5% MED - 10% AT - 5% - 10% AT ST'D LOW ST'D LOW - 5% ST'D LOW - 10% AT EXTRA LOW EXTRA LOW - 5% EXTRA LOW - 10% AT ULTRA LOW ULTRA LOW - 5% ULTRA LOW - 10% EXTRA LOW STANDARD LOW LOWER - FAN - HIGHER FANS 0 HORIZONTAL FAN COIL STANDARD UNIT WIRING MAINS SUPPLY 2-2VAC 1PH EARTH NEUTRAL V SUPPLY TO CONTROLS IF FITTED LIVE CONTROL TRANSFORMER ON / OFF V 0V L N TRIMS TAPPINGS 5 AMP FUSE ROWN FINE TUNING 3 SWITCH LUE LACK L N E CAPACITOR Options & Extras Inlet Plenums. Electric Heating. 0 or 2mm Spigots. Side Spigots Upon Request. Condensate Pumps. Fresh Air Connections. All Control Packages Catered For. As part of our continuous improvement initiative we have to reserve the right to alter the specifications and or dimensions without notice. Therefore, please check your selections and any recent updates by calling the Ability internal sales office. AILITY PROJECTS LTD, JOHNSON ROAD, FERNSIDE PARK, WIMORNE, DORSET. H 7SE. TEL 012 80 FAX 012 8711 email : sales@abilityprojects.co.uk 8 LIT T0 - Feb 05