HYDRAULIC APPLICATION Conveyors; Metal working machines; Machines for agriculture; Road building machines; Mining machinery; Food industries; Special vehicles; Plastic and rubber machinery etc. CONTENTS Specification data... 87 Function diagrams... 88 90 Dimensions and mounting... 91 Shaft extensions... 92 Dimensions and mounting- S, V... 9 94 Internal Spline data... 95 Permissible shaft loads... 95 Tacho connection... 96 Order code... 96 OPTIONS Model- Disc valve, geroler; Flange with wheel mount; Short motor; Tacho connection; Side and rear ports Shafts- straight, splined and tapered; Metric and BSPP ports; Other special features. GENERAL Displacement, [cm /rev.] Max. Speed, [RPM] Max. Torque, [danm] Max. Output, [kw] Max. Pressure Drop, [bar] Max. Oil Flow, [l/min] Min. Speed, [RPM] Permissible Shaft Loads, [dan] Pressure fluid O Temperature range, [C] 2 Optimal Viscosity range, [mm /s] Filtration 161,1 725 625 1 47,2,5 0 115 0 5 P =1700; P =00 rad Mineral based- HLP(DIN 51524) or HM(ISO 674/4) -0 90 ISO code /16 (Min. recommended fluid filtration of 25 micron) a Pressure drop (bar) Oil flow in drain line Viscosity 2 (mm /s) 5 5 Oil flow in drain line (l/min) 1,5 1 2 Pressure Losses P bar 14 12 8 6 4 2 0 0 0 50 60 70 80 90 0 1 1 Q, l/min 86
SPECIFICATION DATA Type 160 0 15 0 500 60 725 Displacement [cm /rev.] Max. Speed, [RPM] Max. Torque [danm] Max. Output [kw] Max. Pressure Drop [bar] Max. Oil Flow [l/min] Max. Inlet Pressure [bar] Max. Return Pressure without Drain Line or Max. Pressure indrainline,[bar] Max. Return Pressure with Drain Line [bar] peak** int.* peak** peak** peak** 0-0 RPM 0-00 RPM >00 RPM 0-max. RPM 161,1 625 780 47 56 66 26,5 2 0 2 280 0 00 1 Max. Starting Pressure with Unloaded Shaft, [bar] Min. Starting Torque [danm] Min. Speed***, [RPM] Weight, [kg] at max. press. drop at max. press. drop W S V 4 41 22 15 11 1,4 625 0 59 71 82,5 0 2 280 150 00 1 4 52 9,5 22,5 15,5 11,5 251,8 500 600 7 88 2,5 0 2 280 150 00 1 5 6 8 21 2 16 12 26, 80 460 95 114 1,5 0 2 280 150 00 1 74 89 7 22 24 17 1 4,9 05 65 8 126 144 0 5 180 2 150 00 1 84 97 6 2 25 18 14 52,6 2 285 122 17 160 26,5 0 160 180 150 00-1 95 6 5 24 26 19 15 612, 6 247 12 18 161 24, 27,5 160 190 151,4 00-1 95 8 5 25 27 16 725 172 5 165,2 26,8 115 160 151,4 00-1 95 1 5 26 28 21 17 * Intermittent operation: the permissible values may occur for max. % of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds of 5 RPM lower than given, consult factory or your regional manager. 1) Intermittent speed and intermittent pressure must not occur simultaneously. 2) Recommended filtration is per ISO cleanliness code /16. A nominal filtration of 25 micron or better. ) Recommend using a premium quality, anti-wear type mineral based hydraulic oil, HLP(DIN51524) or HM(ISO674/4). If using synthetic fluids consult the factory for alternative seal materials. 4) Recommended minimum oil viscosity 1 mm²/s at 50ºC. 5) Recommended maximum system operating temperature is 82ºC. 6) To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for -15 minutes. 87
160 FUNCTION DIAGRAMS 0 The function diagrams data was collected at back pressure 5 bar and oil with viscosity of 2 mm²/s at 50 C. 88
FUNCTION DIAGRAMS 15 89
0 FUNCTION DIAGRAMS 500 The function diagrams data was collected at back pressure 5 bar and oil with viscosity of 2 mm²/s at 50 C. 90
DIMENSIONS AND MOUNTING DATA Port A Port B Porting Side Ports Mounting Square Mount (4 Holes) C T P (A,B) P (A,B) E Rear Ports plugged W Wheel Mount Port A Port B T Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW C: 4xM- mm depth P (A,B): 2xG/4 or 2xM27x2-17 mm depth T: G 1/4 or M14x1,5-12 mm depth (plugged) Type 160 0 15 0 500 60 725 L, mm 190 195 1 211 221 25 242,5 260 Type E 160 E 0 E E 15 E 0 E 500 E 60 E 725 L, mm 0 5 211 221 21 245 252,5 270 L,mm 2 Type L, mm Type L, mm L,mm 2 *L 1, mm 145 151 161 171 185 192,5 W 160 W 0 W W 15 W 0 W 500 W 60 W 725 12 128 14 144 154 168 1,5 19 WE 160 WE 0 WE WE 15 WE 0 WE 500 WE 60 WE 725 1 18 144 154 164 178 185,5 19 7 78 84 94 4 118,5 14 16,5 21,5 27,8 7,0 47,5 61,5 72,5 86,5 * The width of the gerolor is,5 mm greater than L. 1 91
SHAFT EXTENSIONS C -ø straight, Parallel key A12x8x70 DIN 6885 Max. Torque 12,8 danm K -tapered 1:, Parallel key B12x8x28 DIN 6885 Max. Torque,7 danm S=46 Tightening Torque 50± danm max 114 max 114 -ø1½" straight, Parallel key "x CO 8 8 "x 2¼" BS46 Max. Torque 12,8 danm SH -ø1½" splined 17T, DP 12/24 ANSI B92.1-1976 Max. Torque 12,8 danm max 114 max 114 SL -ø4,85 p.t.o. DIN 9611 Form 1 Max. Torque 77 danm - Motor Mounting Surface max 14 92
DIMENSIONS AND MOUNTING DATA - S and V max L T Port A Port B Porting Side Ports Mounting S - Short Mount C 4xø14,2 max 6,1 min 2,9 P (A,B) "O" Ring x T 8±0,2 P (A,B) 72±0,2 E Rear Ports plugged V - Very Short Mount Port A max 25 Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Port B max L Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW 72±0,2 Drain port max L "O" Ring 0x +0,5 90,5-1,6 C: 4xM- mm depth P(A,B) : 2xG/4 or 2xM27x2-17 mm depth T: G ¼ or M14x1,5-12 mm depth (plugged) Type S 160 S 0 S S 15 S 0 S 500 S 60 S 725 L, mm 146 151 157 166 177 191 198,5 216 Type SE 160 SE 0 SE SE 15 SE 0 SE 500 SE 60 SE 725 L, mm 156 161 167 176 187 1 8,5 226 L,mm 2 Type L, mm Type L, mm L,mm 2 *L 1, mm 96 1 7 116 127 142 146,5 167 V 160 V 0 V V 15 V 0 V 500 V 60 V 725 1 6 112 121 12 146 15,5 171 VE 160 VE 0 VE VE 15 VE 0 VE 500 VE 60 VE 725 111 116 122 11 142 156 16,5 181 51,5 16,5 56,5 21,5 62,8 27,8 72 7,0 82,5 47,5 96,5. 61,5 4 72,5 121,5 86,5 * The width of the gerolor is,5 mm greater than L. 1 9
DIMENSIONS OF THE ATTACHED COMPONENT S ø92 +1 F: Oil circulation hole G: Internal drain channel H: Hardened stop plate I: O- Ring xmm 0 J: 4xM12-18 mm depth, 90 T: Drain connection G1/4 or M14x1,5 V Four depth min F: Oil circulation hole G: Internal drain channel H: Hardened stop plate I: O- Ring 0xmm DRAIN CONNECTION A drain line ought to be used when pressure in the return line can exceed the permissible pressure. It can be connected: - For S at the drain port of the motor; - For V at the drain connection of the attached component. The maximum pressure in the drain line is limited by the attached component and its shaft seal. The drain line must be possible for oil to flow freely between motor and attached component and must be led to the tank. The maximum pressure in the drain line is limited by the attached component and its seal. 94
INTERNAL SPLINE DATA FOR THE ATTACHED COMPONENT Standard ANSI B92.1-1976, class 5 [m=2.1166; corrected x.m=+1,0] Fillet Root Side Fit mm Number of Teeth z 16 Diametral Pitch DP 12/24 Pressure Angle 0 O Pitch Dia. D,8656 Major Dia. Dri 8,4 +0,4 Minor Dia. Di 2,15 +0,04 Space Width [Circular] Lo 4,516±0,07 Fillet Radius Rmin 0,5 Max. Measurement between Pin L 26,9 +0, Pin Dia. d 4,85±0,001 L Hardening Specification: HRC 60±2 HRC 52 0,7±0,2 mm effective case depth Material MoCr4 DIN 17 or better PERMISSIBLE SHAFT LOADS The output shaft runs in tapered bearings that permit high axial and radial forces. Curve " 1" shows max. radial shaft load. Any shaft load exceeding the values quoted in the curve will seriously reduce motor life. The two other curves apply to a B bearing life of 000 hours at 0 RPM. P rad (dan) 1 5000 00 000 00 Pa=0 Pa=00 dan 00 0 max 114 50 0 150 180 (mm) Pa =00 dan max max 181 Pa =00 dan max 95
WITH TACHO CONNECTION ORDER CODE 1 2 4 5 6 7 8 9 Pos.1 - Mounting Flange S V W Pos.2 - Port type E - Side ports - Rear ports Pos. - Displacement code Pos.4 - Shaft Extensions* C CO K SL SH - Square mount, four holes - Short mount - Very short mount - Wheel mount 160-161,1[cm /rev] 0-1,4[cm /rev] - 251,8[cm /rev] 15-26,[cm /rev] 0-4,9[cm /rev] 500-52,6[cm /rev] 60-612,[cm /rev] (without Function diagram) 725-725,0[cm /rev] (without Function diagram) - ø straight, Parallel key A12x8x70 DIN6885 - ø1½ straight, Parallel key / 8 x / 8 x2¼ BS46 - ø45 tapered 1:, Parallel key B12x8x28 DIN6885 - ø4,85 p.t.o. DIN 9611 Form 1 - ø1½" splined 17T ANSI B92.1-1976 Pos. 5 - Ports - BSPP (ISO 228) M - Metric (ISO 262) Pos. 6 - Speed Monitoring T Pos. 8 - Rotation R - Standard Rotation - Reverse Rotation Pos. 9 - Option (Paint)** P PC - no Paint - Painted - Corrosion Protected Paint Pos. - Design Series - none - with tacho connection Pos. 7 - Special Features LL LSV - none -Low Leakage - Low Speed Valve - Factory specified (only for side ports) NOTES: * The permissible output torque for shafts must be not exceeded! ** Color at customer's request. The hydraulic motors are mangano-phosphatized as standard. 96