(UK/0126/0021) MI-008 United Kingdom of Great Britain and Northern Ireland Certificate of EC type-examination of a measuring instrument Number: UK/0126/0021 Revision 5 issued by the Secretary of State for Business, Innovation and Skills Notified Body Number 0126 In accordance with the requirements of the Measuring Instruments (Material Measures of Length) Regulations 2006 (SI 2006/1267) and the Measuring Instruments (Non-Prescribed Instruments) Regulations 2006 (SI 2006/1270) which implement, in the United Kingdom, Council Directive 2004/22/EC, this certificate of EC type-examination has been issued to: Ningbo Land Industrial Co Ltd Zhejiang Newland Industrial Holding Co Ltd 68 Chengdong Road YuYao City Zhejiang China 315400 in respect of: accuracy class: nominal length and width: Material measure of length II 2 m x 12.5 mm Additional models, lengths and widths are described in Section 7 of the descriptive annex to this certificate. This revision replaces previous versions of the certificate. Issue Date: 22 July 2010 Valid Until: 27 February 2018 Reference No: T1126/0008 Signatory: P R Dixon for Chief Executive National Weights & Measures Laboratory (part of the National Measurement Office) Department for Business, Innovation and Skills Stanton Avenue Teddington Middlesex TW11 0JZ United Kingdom
Descriptive Annex 1 REGULATIONS The measuring instrument in respect of which this certificate of EC pattern approval has been issued is subject to the provisions and requirements of the requirements of the Measuring Instruments (Material Measures of Length) Regulations 2006 (SI 2006/1267) and the Measuring Instruments (Non-Prescribed Instruments) Regulations 2006 which implement, in the United Kingdom, Council Directive 2004/22/EC. 2 DESCRIPTION OF THE PATTERN The pattern is a small, composite, retractable measure, which may be in a case. The blade has a nominal length of 2 m and a nominal width of 12.5 mm, and is made of steel with a sliding hook at the free end. The hook is stamped with the number 1. The blade has black and red markings on a yellow or white background protected by a clear film. The measure is graduated in millimetres throughout on both edges of the blade with half-centimetres also marked. The centimetre intervals are numbered consecutively from 1 to 9 which are repeated throughout the length of the blade. The 10-centimetre intervals are numbered consecutively throughout. The case is marked << 59 mm >> to allow for internal measurements. 3 TECHNICAL DATA 3.1 (a) Accuracy class: II (b) Nominal length: 2 m (c) Scale interval: 1 mm 4 INSCRIPTIONS The following inscriptions are marked at the beginning of the blade on the front face: (a) Nominal length: 2 m (b) Manufacturer's identification: LAND and/or logo (c) Class of accuracy: II (d) EC type approval certificate number: UK/0126/0021 5 APPROVAL CONDITIONS The certificate is issued subject to the following conditions. 5.1 Legends and inscriptions 5.1.1 The following markings and inscriptions are durably and legibly marked onto the blade of the tape measure: and fulfil the requirements of Paragraph 9 of Annex I of the Directive 2004/22/EC: CE mark Supplementary metrology mark Notified Body number Accuracy class Manufacturers mark or name Certificate number Tractive force (if applicable) Reference temperature (if other than 20 C) 5.1.2 The model of the tape measure cases are identified by the series number. The following codes may follow the case series number to denote the associated blade width: 2 / 16
W E X -1 16 mm 19 mm 25 mm 10mm Alternatively no series number denotes a nominal width of 12.5 mm. 6 LOCATION OF MARKS 6.1 The inscriptions in section 4 together with the CE marking, supplementary metrology marking and notified body number are printed on the blade near the beginning. 7 ALTERNATIVES 7.1 Having alternative models of steel tape measure blade as described in Table 1 below. Accuracy class Nominal length (m) 3 / 16 Nominal widths (mm) II 2 12.5, 16 II 3 12.5, 16, 19 II 5 12.5, 16, 19, 25 II 8 25 II 10 10, 12.5, 25 II 20 10, 12.5 II 30 10, 12.5 II 50 10, 12.5 Table 1 7.1.1 The blade may be enclosed in a case which is identified by the model series number, e.g. JC-203, where: JC (model), 2 (nominal length), 03 (case series number). The following table lists those cases which are marked with a case dimension for making internal measurements. Accuracy class Case series Case marking (mm) II 03 59 II 03 66 II 03 78 II 08 63 II 08 74 II 09 64 II 53 60 II 53 70 II 53 87 II 56 65 II 56 73
Accuracy class Case series Case marking (mm) II 56 88 II 58 60 II 58 70 II 58 80 II 68 56 II 68 65 II 68 76 II 68 85 II 68 92 II 79 61 II 79 70 II 79 81 II 80 62 II 80 72 II 80 82.5 II 85 60 II 85 70 II 86 61 II 86 70 II 86 81 Table 2 7.1.2 The blade may be enclosed in a case which is identified by the model series number, e.g. LD-2N07W, where: LD (model), 2 (nominal length), N07 (case series number) and W (blade width), but which is not marked with a case dimension for making internal measurements. 7.1.3 The case may be fitted with any of the following: blade lock, belt clip wrist / carrying strap. 7.1.4 The case, which may be any colour, may be marked with a case dimension, as indicated in table 2, for making internal measurements. The strap should not interfere with the measurement when making internal dimension measurements. 7.1.5 The case may be fitted with a rubber sleeve / grip. 7.1.6 The belt clip shall not obscure case dimension markings. 4 / 16
7.1.7 Having the following markings, which are in addition to the manufacturer s identification of LAND and/or logo. FIVE STAR BTS (TOPCULAR HIRDAVAT A.S) SEB AUSONIA CROSS LUX PEVEC DOIT & GARDEN MIGROS TOPEX (Top Tools) MEISTER WERKZEUGE GmbH KWB (Karl W.Burmeister GmbH & HM Müllner MESSTECHNIK (Herbert Muellner Co.KG) DHT, (Detay Baglanti Elemanlari San. Ve Tic. A.S) Werkzeuggrosshandel GmbH) EMC DISTRIBUTION of CASINO GROUPE 7.1.8 Having the following alternative model identifications for the additional markings specified in 7.1.7. 7.1.8.1 Model number JC-G1009 JC-G2009 JC-G3009 JC-G5009 JC-GJ209 JC-GJ309 JC-GJ509 JC-290W JC-390W JC-590E JC-286W JC-386W JC-586X JC-256 JC-356W JC-556W JC-556X BTS Model Number BTS-12361 BTS-12362 BTS-12363 BTS-12365 BTS-12372 BTS-12373 BTS-12375 BTS-12309 BTS-12311 BTS-12313 BTS-12317 BTS-12319 BTS-12321 BTS-12301 BTS-12303 BTS-12305 BTS-12325 LD-381W BTS- 12331 LD-581E BTS- 12333 LD-581X BTS- 12335 Table 3 5 / 16
7.1.8.2 Model number Alternative Model Number JC-258 573522 JC-358W 573523 JC-558E 573524 JC-858X 824305 JC-282 573101 JC-382W 573102 JC-582E 573103 JC-882X 573104 JC-5N09E 870560 Table 4 7.1.8.3 Model number Alternative model number JC-GJ309 417.30 JC-GJ509 417.50 JC-G2005 402.20 JC-386W 649.3.16 JC-386E 649.3.19 JC-586E 649.5.19 JC-586X 649.5.25 JC-1086X 649.10.25 JC-2008 4.20 JC-3008 4.30 JC-J506 4.50 Table 5 7.1.8.4 Model number PEVEC Model number DOIT & GARDEN MIGROS Model Number JC-5N09E 870570 870572 Table 6 6 / 16
7.1.8.5 Model number JC-297W JC-397W JC-597E JC-GJ502 TOPEX (Top Tools) Model Number 27C214 27C216 27C218 28C450 Table 7 7.1.8.6 Model number JC385W JC385W JC585E JC585E JC885X JC885X JC-G3011 HM Müllner MESSTECHNIK Model Number RK316 RK316N RK519 RK519N RK825 RK825N RK3011 Table 8 7.1.8.7 Model number KWB Model Number LD-2N12W 0601-02 LD-3N12W 0601-03 LD-5N12E 0601-05 LD-10N12X 0608-10 Table 9 7.1.8.8 Model number MEISTER Model Number LD-5N09E 6509000 Table 10 7 / 16
7.1.8.9 Model number EMC Model Number LD-2015 558120 LD-3015 558130 LD-5015 558150 Table 11 7.2 Having alternative models of tape measure blade as described in table 11 below, manufactured from fibreglass. The blade is enclosed in a case with a winder and handstrap. Accuracy class Nominal length (m) Table 13 8 / 16 Nominal width (mm) III 10 12.5 III 15 12.5 III 20 12.5 III 30 12.5 III 50 12.5 Table 12 7.2.1 The blade is graduated in 2-millimetre intervals along one edge on both sides of the blade. The centimetre intervals are numbered consecutively from 1 to 9 for each decimetre; this pattern is repeated throughout the blade. Half-decimetres are marked with an arrow. The number of metres is stated in red just before the decimetre designation. The scale markings are in black on a white background. The blade is terminated by a plastic ring, which is attached to it by a riveted metal strip approximately 2 cm long. A transparent plastic strip reinforces the blade for its first 14 cm (approximately). 7.2.2 The blade may have the zero mark offset by approximately 10 cm inwards from the end of the blade (Figure 34), a plastic strip is used to reinforce part of the offset area. 7.2.3 The blade may be enclosed in a case which is identified by the model series number, e.g. JC-1008, where: JC (model), 10 (nominal length), 08 (case series number). The cases are not marked with a case dimension for making internal measurements. 7.2.4 The blade may be enclosed in a case which is identified by the model series number, e.g. JC-1001, where: JC (model), 10 (nominal length), 01 (case series number). The cases are not marked with a case dimension for making internal measurements. Model number Nominal length (m) Nominal width (mm) JC-1001 10 13 JC-2001 20 13 JC-3001 30 13 JC-5001 50 13
7.2.5 The blade may be enclosed in a case which is identified by the model series number, e.g. JC-J202, where: JC (model), 10 (nominal length), J*2 (case series number). The model may have alternative model identifications for the additional markings specified in 7.1.7. The cases are not marked with a case dimension for making internal measurements. Model number DHT Model Number Nominal length (m) Nominal width (mm) JC-J202 J2-JC-2002 20 13 JC-J302 J2-JC-3002 30 13 JC-J502 J2-JC-5002 50 13 Table 14 7.3 Having the following models of steel long tape, series G11, as described in table 14 below. Model number Nominal length (m) Nominal width (mm) JC-G1011 10 10 JC-G2011 20 10 JC-G3011 30 10 Table 15 7.3.1 The steel blade has the zero mark offset by approximately 14 cm inwards from the end of the blade (Figure 32). The blade is terminated by a metal end ring, which is attached by means of a metal clamp approximately 15 mm long. The number of metres is also marked in the centre of every decimetre. 7.4 Having the following models: Model number Nominal length (m) Nominal width (mm) JC385W 3 16 JC585E 5 19 JC585X 5 25 JC1085X 10 25 LD-3N09W 3 16 LD-5N09E 5 19 LD-5N09X 5 25 JC-GJ209 20 12.5 JC-GJ309 30 12.5 JC-GJ509 50 12.5 Table 16 9 / 16
8 ILLUSTRATIONS Figure 1 The pattern Figure 2 Series 03 case Figure 3 Series 08 case Figure 4 Series 09 case Figure 5 Series 53 case Figure 6 Series 56 case Figure 7 Series 58 case Figure 8 Series 68 case Figure 9 Series 79 case Figure 10 Series 80 case Figure 11 Series 86 case Figure 12 Series 57 case Figure 13 Series 67 case Figure 14 Series 82 case Figure 15 Series 84-1 case Figure 16 Series 87 case Figure 17 Series 88 case Figure 18 Series 90 case Figure 19 Series 92 case Figure 20 Series 96 case Figure 21 Series N02 case Figure 22 Series N05 case Figure 23 Series G09 case Figure 24 Series 85 case Figure 25 Series N07 case Figure 26 Series N09 case Figure 27 Additional ID mark Figure 28 Additional ID mark Figure 29 Additional ID mark Figure 30 Additional ID mark Figure 31 Additional ID marks Figure 32 Offset zero mark Figure 33 Fibreglass blade example Figure 34 Offset Fibreglass blade Figure 35 Fibreglass Series 01 case Figure 36 Fibreglass Series 08 case Figure 37 Fibreglass Series 12 case Figure 38 Fibreglass Series J06 case Figure 39 Fibreglass Series J03 case Figure 40 Fibreglass Series J02 case Figure 41 Additional identification mark Figure 42 Additional identification mark Figure 43 Fibreglass Series 81 case 9 CERTIFICATE HISTORY ISSUE NO. DATE DESCRIPTION UK/0126/0021 28 February 2008 Type examination certificate first issued. UK/0126/0021 Revision 1 7 September 2009 Additional manufactures markings; PEVEC, DOIT & GARDEN MIGROS, TOPEX and HM Müllner MESSTECHNIK added to section 7.1.7 Additional models added to Table 3 section 7.1.9.1 Sections 7.1.9.4 to 7.1.9.6 added. UK/0126/0021 Revision 2 21 September 2009 Additional manufactures markings; MEISTER WERKZEUGE GmbH and KWB (Karl W.Burmeister GmbH & Co.KG) added to section 7.1.7 Section 7.1.8 removed and Section 7.1.9 renumbered Sections 7.1.8.7, 7.1.8.8, 7.3 and 7.3.1 added. UK/0126/0021 Revision 3 25 March 2010 Section7.1.7 Additional manufactures markings; DHT, (Detay Baglanti Elemanlari San. Ve Tic. A.S). Figure 41 Additional identification mark UK/0126/0021 Revision 4 08 April 2010 Addition of Sections7.2.4 and 7.2.5 Modification to section 7.3: reference to Table 12 changed to Table 14 10 / 16
UK/0126/0021 Revision 5 22 July 2010 Modification to section 7.1.7 i) BTS (MAR IC VE DIS TICARET A.S.) replaced with BTS (TOPCULAR HIRDAVAT A.S.). ii) Addition of : EMC DISTRIBUTION of CASINO GROUPE Modification to section 7.1.8.1: i) Revision of BTS references, from:- BTS09-10M, BTS09-20M, BTS09-30M, BTS09-50M, BTSJ09-20M, BTSJ09-30M, BTSJ09-50M, BTS82-2M, BTS82-3M, BTS82-5M, BTS75-2M, BTS75-3M, BTS75-5M, BTS07-2M, BTS07-3M, BTS07-5M, BTS81-3M, BTS81-5M*19MM, BTS81-5M*25MM. to:- BTS-12361, BTS-12362, BTS-12363, BTS-12365, BTS-12372, BTS-12373, BTS-12375, BTS-12309, BTS-12311, BTS-12313, BTS-12317, BTS-12319, BTS-12321, BTS-12301, BTS-12303, BTS-12305 ii) Addition of models:- LD-381W, JC-556X, LD-581E and LD-581X, including BTS item nos. iii) Revision of Item references:- JC-290, JC-286 (addition of suffix W), JC-G1009, JC-G2009, JC- G3009, JC-G5009, JC-GJ209, JC-GJ309 &, JC- GJ509 (removal of suffix -1). Addition of: Section 7.1.8.9, Section 7.4, Figure 42 & Figure 43 Figure 1 Example of the Pattern Figure 2 Case style 03 series Figure 3 Case style 08 series 11 / 16
Figure 4 Case style 09 series Figure 5 Case style 53 series Figure 6 Case style 56 series Figure 7 Case style 58 series Figure 8 Case style 68 series Figure 9 Case style 79 series Figure 10 Case style 80 series Figure 11 Case style 86 series 12 / 16
Figure 12 Case style 57 series Figure 13 Case style 67 series Figure 14 Case style 82 series Figure 15 Case style 84-1 series Figure 16 Case style 87 series Figure 17 Case style 88 series Figure 18 Case style 90 series Figure 19 Case style 92 series 13 / 16
Figure 20 Case style 96 series Figure 21 Case style N02 series Figure 22 Case style N05 series Figure 23 Case style G09 series Figure 24 Case style 85 series Figure 25 Case style N07 series Figure 26 Case style N09 series 14 / 16
Figure 31 Additional identification marks: LUX Figure 27 Additional identification mark: BTS Figure 28 Additional identification mark: FIVE STAR Figure 29 Additional identification mark: SEB Figure 30 Additional identification mark: Ausonia Figure 32 Offset Zero Mark Figure 33 Fibreglass blade Figure 34 Fibreglass Blade with offset zero mark 15 / 16
Figure 35 Fibreglass Case style 01 series Figure 36 Fibreglass Case style 08 series Figure 37 Fibreglass Case style 12 series Figure 38 Fibreglass Case style J06 series Figure 39 Fibreglass Case style J03 series Figure 40 Fibreglass Case style J02 series 16 / 16
Figure 41 Additional identification mark Figure 42 Additional identification mark Figure 43 Fibreglass Case style 81 series Crown copyright 2010. NATIONAL WEIGHTS AND MEASURES LABORATORY (part of the National Measurement Office) This material may be freely reproduced except for sale. 17 / 17