accessories-options 11b ML 10/4/13 ACCESSORIES & OPTIONS GUIDE 1
TABLE OF CONTENTS Door Limit Switches 3-5 Controllers 6 Motor Control Panels 7 Specialty Motors 8 Mounting Hardware 9 Filters 10 Special Construction 11 Colors-Materials-Finishes 11 Explosion Proof 11 Washdown/Moisture Resistant 11 Tamper Proof 11 2
DOOR LIMIT SWITCHES Mechanical Door Limit Switches - used when automatic control of an air curtain(s) is required. Door limit switches turn the air curtain on when the door opens and off when the door closes. Roller Type door limit switches are typically used for roll- up type doors. Plunger Type door limit switches are used for swinging type doors. Combination Plunger / Roller Type door limit switches are used for all types of doors. Washdown switches are used in areas of high moisture content and/or when exosed to direct water. Explosion Resistant switches are used to provide protection from the ignition of specified gases due to sparks created by the motor s internal components. (Class 1, Division 1, Group D) Contact the factory for other classifications not listed. Note: An optional motor control panel or controller will be required if the total field conditions exceed ANY of the specified voltages, phase, amps or HP parameters specified for each type of mechanical door limit switch. Combination Plunger/Roller Part # 99-014 250 Volts, 1ø, 20 Amps, 1 HP Max, NC/NO, 1 Pole, NEMA 1 Roller Type Washdown Part # 99-267 - 250 Volts, 1ø, 10 Amps, 1/2 HP Max, NC/NO, 1 Pole, NEMA 4X Part # 99-015 - 600 Volts, 1ø, 20 Amps, 1 HP Max, NC/NO, 1 Pole, NEMA 4X Part # 99-267 Part # 99-015 3
Roller Type Explosion Resistant Part # 99-016 - 250 Volts, 1ø, 15 Amps, 3/4 HP Max., NC/NO, 1 Pole, NEMA 7 Magnetic Reed Door Limit Switches - used when automatic control of an air curtain(s) is required. Magnetic door limit switches turns the air curtain on when the door opens and off when the door closes. Flush Mounted Magnetic switches are used when installation allows for conceiling the wires and switches. Surface Mounted Magnetic switches are used when wires cannot be run through the wall or frame. Floor mounted switches are used for industrial roll-up doors with forklift traffic. Commercial Plastic Wireless Surface mounted switches are used for lower traffic applications that requires no exposed wires. These switches must have a minimum light exposure 2000 Lux on the solar panel and have less than 200 cycles per hour. Note: An optional motor control panel or controller is required when a wired magnetic door limit switch is used. Commercial Plastic Flush Mounted Part # 99-275 24 Volts, 1/2 Amps, NC/NO, Wired, NEMA 1 Commercial Plastic Surface Mounted Part # 99-018 24 Volts, 1/2 Amps, NC/NO, Wired, NEMA 1 4
Commercial Plastic Wireless Surface Mounted Part # 99-118 24 Volts, 2 Amps, Wireless, Solar Charged, NEMA 1 (Kit # J0053 (115V) or Kit # J0054 (208/230V), both includes Wireless Switch and Switch Controller, not shown) Industrial Aluminum Floor Mounted Part # 99-017 24 to 120 Volts, 3 Amps, NC/NO, Wired, NEMA 1 Industrial Aluminum Surface Mounted Part # 99-081 24 to 120 Volts, 3 Amps, NC/NO, Wired, NEMA 1 5
CONTROLLERS Solid State Controllers - used when automatic control of an air curtain(s) is required with Low Voltage control voltage, with or without time delay. Door limit or magnetic switches can be used to turn the air curtain on when the door opens and off when the door closes. Note: Solid state controllers are limited to the voltages, phase, amps or HP parameters specified for each type. Controller without Time Delay Part # 99-052 ½ HP, 120 Volts, NC/NO, and Class 2 Low Voltage control Part # 99-053 ½ HP, 208/230 Volts, NC/NO, and Class 2 Low Voltage control wiring Part # 99-052 (Shown) Part # 99-052 (Shown) with 4 X 4 Junction Box Controller with Adjustable Time Delay Part # 99-050 ½ HP, 120 Volts, ½ Amps, NC/NO, 5 600 sec Time Delay, NEMA 1 Part # 99-051 ½ HP, 208/230 Volts, ½ Amps, NC/NO, 5 600 sec Time Delay, NEMA 1 Part # 99-050 (Shown) Part # 99-052 (Shown) with 4 X 4 Junction Box 6
MOTOR CONTROL PANELS Unheated, Electric, Steam, Hot Water, Indirect Fired Gas, Direct Fired Gas Heated Control Panels used when automatic control of an air curtain(s) is required, but must be used in conjunction with door limit switches to turn the air curtain on when the door opens and off when the door closes. Contact factory for panel part numbers. NOTE: All unheated panels are remote mounted (except electric heated) as standard. (Optional unit installation available). Additional panel materials available. Contact factory for details. NEMA 1 (IP 10) PANEL For indoor use only. Provides protection from dust. Enclosures may be painted metal or fiberglass. NEMA 4X (IP 56) PANEL for indoor or outdoor use. Provides protection from hose directed water and corrosion. Enclosures may be stainless steel metal or fiberglass. (Not available for Electric, Indirect Fired Gas and Direct Fired Gas heated models) NEMA 7 PANEL for indoor use. Provides protection from the ignition of specified gases due to sparks created by the panel s internal components. Enclosures is cast aluminum with milled edges. (Class 1, Division 1, Group C & D) (Not available for Electric, Indirect Fired Gas and Direct Fired Gas heated models) 7
SPECIALTY MOTORS Washdown and Explosion Resistant Motors specialty motors available to meet specified field conditions, such as washdown or sprayable motors, and explosion proof motors. NOTE: Additional motor materials and motor classifications are available. Contact factory for details. NEMA 4X (IP 56) MOTOR for indoor or outdoor use. Provides protection from hose directed water and corrosion. Motors are epoxy coated with stainless steel shafts and bearing shields. NEMA 7 MOTOR for indoor use. Provides protection from the ignition of specified gases due to sparks created by the motor s internal components. Motors are sealed and are typically totally enclosed non-vented (TENV). (Class 1, Division 1, Group D) 8
MOUNTING HARDWARE Mounting Brackets heavy gauge steel, gavenized and specificially designed to be utilized with Mars Air Curtains. Used to simplify installation or for clearing obstructions in the installation area and/or in front of or above the door header. NOTE: When selecting the appropriate brackets, choose the bracket that has the clearance slightly greater than the field clearance required. All bracket have a rust ressitant G90 Galvanized metal finish as standard. For additional bracket materials and custom finishes, contact the factory for details. Adjustable Mounting Brackets Part # J0004-2 ½ Clearance Part # J0005-4 Clearance Part # J0006-7 Clearance Part # J0007-10 Clearance (Part # J0004 Shown) (Part # J0005, J0006, and J007 Shown) Side Extension Plates Part # J0016-5 Clearance Part # J0017-7 Clearance Part # J0018-9 Clearance Extended Wall Mounting Brackets Part # J0008G - 10 Clearance Part # J0009G - 17 Clearance Shown in conjunction with an Adjustable Mounting Bracket Part # J0010G - 19 Clearance Part # J0011G - 23 Clearance 9
FILTERS Filters used to capture large particulates in the installation space. Expanded Aluminum filters are used when washable or reusable filters are required. Paper filters are used when throw away or disposable filters are required. NOTE: Additional materials and filter construction are available. Contact factory for details. Flat Bank and V-Bank Filter Sections these options are not all available for all series. See submittal sheets for details and availability. ¼, ½ 1 & 2 Aluminum Filters washable expanded aluminum. Contact factory for filter part numbers. ½, 1 & 2 Paper Filters throw away pleated filters require an externally mounted filter frame. Contact factory for frame and filter kit part numbers. 10
SPECIAL CONSTRUCTION Colors Colors available; Battleship Gray (BG), Obsidien Black (OB), Pearl White (PW), Titanium Silver (TS) Contact the factory for additional colors. Materials Stainless steel, aluminum and other materials available. Contact the factory for other materials. Finishes Brushed, grained or annodized aluminum. Brushed, grained or polished stainless steel. Heresite anticorrosion coating. Explosion Proof Class 1, Division 1, Group D, NEMA 12 Washdown / Moisture Resistant Brushed Aluminum, Annodized Aluminum, Brushed 304 SS, Brushed 316 SS, IP56, NEMA 3R, 4, 4X Tamper Proof Used for securing equipment parts within the housing or panel. Used for high risk, such as prison installations. (Tamper Proof Shown) 11