INSTALLATION INSTRUCTIONS Accessory S P/N 08V31-SZA-100C Application 2015 PILOT (LX ONLY) Publications No. AII 51565 Issue Date MAY 2014 PARTS LIST 2 Fog lights Ground bolt Relay Headlight switch TOOLS AND SUPPLIES REQUIRED Fog light harness Left cover Phillips screwdriver Stubby Phillips screwdriver Ratchet 10 mm Socket 10 mm Open end wrench Diagonal cutters Blanket The following tool is available through the Honda Tool and Equipment Program. On the in, click on: Service > Serivce Bay > Tool and Equipment Program, then enter the number under Search. Or, call 888-424-6857. Trim tool set (T/N SOJATP2014) Illustration of the Fog Lights on the Vehicle Right cover RIGHT FOG LIGHT RELAY HEADLIGHT 11 Wire ties 4 Self-tapping screws LEFT QA32919AD 2014 American Honda Motor Co., Inc. All Rights Reserved. AII 51565 (1405) 08V31-SZA-1000-90 1 of 11
INSTALLATION 4. Remove the front bulkhead cover (seven clips). Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 7 CLIPS 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 3. Open the hood, and remove the intake air box (two clips). CLIP INTAKE AIR BOX BULKHEAD COVER QA30303AX 5. With the help of an assistant, remove the front bumper (eight clips, three long clips, four selftapping screws, two long self-tapping screws, four bolts, and two bolts). Place the front bumper on a blanket after removal. QA30302AX 4 SELF- TAPPING S BOLT 2 LONG SELF- TAPPING S 8 CLIPS 3 LONG CLIPS 4 BOLTS BUMPER QA51704AB 2 of 11 AII 51565 (1405) 2014 American Honda Motor Co., Inc. All Rights Reserved.
6. Remove the bezel cover from the left fog light bezel (four retaining tabs). BUMPER BUMPER 4 RETAINING TABS BEZEL COVER 9 RETAINING TABS LEFT FOG LIGHT BEZEL QA32907AD 7. Remove the left fog light bezel from the front bumper (nine retaining tabs). 8. Repeat steps 6 and 7 on the right side of the front bumper. 9. Install the fog light to the front bumper using two self-tapping screws. NEW LEFT COVER LEFT FOG LIGHT BEZEL Reuse. QA32918AD 11. Install the new left cover to the left fog light bezel. 12. Repeat steps 9 through 11 to install the right fog light assembly to the right side of the front bumper. BUMPER QA32917AD 10. Reinstall the left fog light bezel to the front bumper. 2014 American Honda Motor Co., Inc. All Rights Reserved. AII 51565 (1405) 3 of 11
13. Under the radiator reservoir, locate the vehicle 1-pin connector blue-taped to the vehicle harness. Remove the blue tape to free the connector. 1-PIN RADIATOR RESERVOIR POWER STEERING RESERVOIR WASHER TANK 16. Route the fog light harness forward, and secure the fog light harness ground terminal to the vehicle frame with the ground bolt supplied. GROUND TERMINAL GROUND BOLT Supplied. FRAME BLUE TAPE Remove. 1-PIN GROUND TERMINAL QA32909AD 17. Secure the clip on the fog light harness to the vehicle panel hole. QA32908AD 14. Get the fog light harness. Plug the fog light harness 1-pin connector into the vehicle 1-pin connector you just freed. 15. Route the ground terminal from the fog light harness down under the washer tank. PANEL HOLE CLIP QA32910AD 4 of 11 AII 51565 (1405) 2014 American Honda Motor Co., Inc. All Rights Reserved.
18. Route the other end of the fog light harness 2-pin connector along the vehicle harness. WASHER TANK 20. Route the fog light harness 2-pin connector over the fan shroud, and along the vehicle harness toward the left side of the vehicle. FAN SHROUD 4 WIRE TIES QA32911AD 19. Secure the fog light harness to the vehicle harness using four wire ties. 2-PIN QA32912AD 2014 American Honda Motor Co., Inc. All Rights Reserved. AII 51565 (1405) 5 of 11
21. Continue to route the fog light harness 2-pin connector down and through the front bulkhead. 24. Secure the fog light harness to the vehicle harness using one wire tie in the area shown. WIRE TIE 2-PIN QA32913AD QA32915BD 22. Secure the clip on the fog light harness to the vehicle panel hole. LEFT HEADLIGHT PANEL HOLE CLIP WIRE TIE CLIP QA51705AB 23. Secure the fog light harness to the vehicle harness using one wire tie. 6 of 11 AII 51565 (1405) 2014 American Honda Motor Co., Inc. All Rights Reserved.
25. Secure the fog light harness to the vehicle harness using five wire ties in the areas shown. 5 WIRE TIES 27. Lower the tilt lever and pull the steering wheel out. UPPER STEERING COLUMN COVER 4 RETAINING TABS Push. TILT LEVER 28. Remove the upper steering column cover: QA51707AB Remove two self-tapping screws. Push the upper cover in at the areas shown to release the four retaining tabs. 29. Remove the lower steering column cover (two selftapping screws and one screw). QA32916BD LOWER STEERING COLUMN COVER 26. With the help of an assistant, bring the front bumper to the vehicle, and plug two fog light harness 2-pin connectors to two fog lights. Reinstall the front bumper. 2-PIN QA51708AB BUMPER QA51706AB 2014 American Honda Motor Co., Inc. All Rights Reserved. AII 51565 (1405) 7 of 11
30. Turn the steering wheel 90 counterclockwise, and unplug the vehicle connector from the headlight switch. 32. Hold the retaining tab, then install the new headlight switch to the steering column. Secure it with the two self-tapping screws. NOTE: Do not push on the lever when installing the case. TAB HOLE STEERING COLUMN CASE HEADLIGHT STEERING WHEEL 701112AE 31. Remove two self-tapping screws from the headlight switch. While pushing the retaining tab, remove the headlight switch from the steering column. NOTE: Do not pull on the lever when removing the switch. LEVER RETAINING TAB NEW HEADLIGHT (reused) 701114AE 33. Plug the vehicle connector into the new headlight switch. TAB HOLE STEERING COLUMN CASE RETAINING TAB NEW HEADLIGHT LEVER HEADLIGHT 701113AE 701115AE 8 of 11 AII 51565 (1405) 2014 American Honda Motor Co., Inc. All Rights Reserved.
34. Remove the right front side step trim (four clips). 36. Install the relay into the vehicle relay block. RIGHT SIDE STEP TRIM RELAY RELAY BLOCK PASSENGER S SEAT 4 CLIPS 700902AE 701111CE 35. Pull away the door opening seal, and remove the right kick panel (two clips). DOOR OPENING SEAL Pull away. 37. Check that all wire harness and cables are routed properly and that all connectors are plugged in. 38. Reinstall all removed parts. 39. Reconnect the negative cable to the battery. 40. Enter the anti-theft code for the audio unit and navigation system if equipped and reset the radio station presets. 41. Reset the clock on vehicles without navigation. RIGHT KICK PANEL 2 CLIPS 700904AE 2014 American Honda Motor Co., Inc. All Rights Reserved. AII 51565 (1405) 9 of 11
Use and Care How to Operate the Fog Lights Turn the headlight switch to the position (headlights on low beam). Turn the fog light switch on (indicator is on). If the fog lights do not turn on, check the fuse and all the connectors, including the ground cable. Fog Light Aiming Adjustment 42. Release the left front inner fender (one long selftapping screw, two self-tapping screws and one bolt). LEFT INNER FENDER Release. HEADLIGHT OFF Low High OFF - - - - 053101AB NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. ON - - ON - BOLT LONG QA51709AB 43. Adjust the fog light: To adjust, turn the aiming adjustment knob in or out until the correct aim is obtained. Adjust the aim according to local laws and regulations. Adjust the aim according to local laws and regulations. To lower. To raise. STUBBY PHILLIPS DRIVER QA51801AB 44. Reinstall all removed parts. 10 of 11 AII 51565 (1405) 2014 American Honda Motor Co., Inc. All Rights Reserved.
BULB REPLACEMENT 1. Release the left front inner fender (one long selftapping screw, two self-tapping screws and one bolt). LEFT INNER FENDER Release. LONG 4. Install the new bulb to the fog light. Use only a Genuine Honda halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-STK-A01 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution. When installing the new bulb, align the cutout in the fog light with the tab on the new bulb and turn the new bulb clockwise until it locks. If not properly aligned, the fog light may annoy oncoming driver s. BOLT QA51709AB NEW BULB 2. Insert your hand inside of the left front inner fender. Unplug the connector from the fog light. BULB Turn. NEW BULB QA51803AB 3. Remove the bulb. QA51802AB 5. Reinstall the removed parts. Check that the wire harnesses are not pinched. Be sure to tighten the clip and bolts securely. 6. Check the operation of the fog light; adjust the aim if necessary. 2014 American Honda Motor Co., Inc. All Rights Reserved. AII 51565 (1405) 11 of 11