Caper Chairs 1 Technical Specifications. Caper Chairs

Caper Chairs 1 Technical Specifications Caper Chairs

Caper Chairs 2 Performance Information Performance Information 3 Methodology and Dimension Description 4 ing Measurements 6 Multipurpose Chair 10 Stacking Stool 12 Multipurpose Stool 13 Cart 15 Casters and Glides 16 Specifications are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice in finishes, materials, specifications, and models and to discontinue models and finishes. Dimensions shown are approximate and given in inches. For specific information about features and options available on each model, prices, and ordering information, please refer to the Herman Miller ing Price Book. Herman Miller, Inc., Zeeland, Michigan L and Caper are among the registered trademarks of Herman Miller, Inc. FLEXNET is a registered trademark of Milliken & Company. Registered trademarks not affiliated with Herman Miller, Inc., (Santoprene) are the properties of their respective owners.

Caper Chairs 3 Performance Information Herman Miller, Inc., work chairs generally meet or exceed all American National Standards Institute/Business and Institutional Furniture Manufacturer s Association (ANSI/ BIFMA) performance requirements per ANSI X5.1-2011, which includes the following tests: strength test-static-type I, Section 5 strength test (for non-tilting chairs), Section 7 Base test-static, Section 8 Drop test dynamic, Section 9 Swivel test cyclic, Section 10 Tilt mechanism test cyclic, Section 11 ing impact test cyclic, Section 12 Stability test, Section 13 Arm strength test vertical static, Section 14 Arm strength test horizontal static, Section 15 durability test cyclic type I, Section 16 durability test (for non-tilting seats), Section 17 Caster/chair base durability test cyclic, Section 18 Leg Strength test, side application, Section 19 Leg Strength test, side application, Section 20 In addition, products have been designed and tested to Herman Miller requirements, which are derived from these ANSI minimum requirements but are much more comprehensive and generally exceed the BIFMA requirements. Herman Miller s Quality Assurance Group randomly and periodically tests standard products (seating) to ensure ongoing compliance to ANSI/BIFMA and Herman Miller corporate standards.

Caper Chairs 4 Methodology and Dimension Description The following measurements are taken with the BIFMA CMD per the Universal Measurement Procedure for the use of BIFMA Chair Measuring Device, BIFMA/CMD-1-98a, draft 18-Jan-98. Rest to Angle Range Width Lumbar Support Range Pan Angle Overall Width Distance between the floor and where the user s thigh meets the seat. Depth Distance from the rear to the front edge of the seat. Width Width of the chair seat at the narrowest point. Pan Angle angle in relation to the floor. -to- Pan Angle Angle between the back and the seat pan at centerline. Distance from the seat to the highest point of the back. Lumbar Support of the lumbar support region as measured from the bottom to the most forward point of the lumbar support. Width Narrowest width of the back. Arms, Inside Measurement Narrowest distance between the arms. Arm pad Distance from the bottom to the highest point of the arm pad. Arm pads, Outside Measurement* Overall distance from the outer edge of the right arm pad to the outer edge of the left arm pad at widest point. Overall Distance from the floor to the highest point of a chair back (unloaded).

Caper Chairs 5 Methodology and Dimension Description Depth Armrest Outside Measurement Armrest Inside Measurement Armrest Overall Depth Outside Base Diameter Base Diameter, Outside Overall diameter of the base. Overall Depth Most forward point of chair to most rearward point of chair.

Caper Chairs 6 Multipurpose Chairs Multipurpose Chairs Depth Width Pan Angle -to- Angle Lumbar Support Width Molded WC111N 16.0 21.5" 16.5" 17.5" 7.5 93.5 19.25" 10.5" 15.5" WC111P 16.0 21.5" 16.5" 17.5" 7.5 93.5 19.25" 10.5" 15.5" FLEXNET WC121N 16.0 21.5" 17.5" 17.75" 2.0 95.0 18.0" 8.0" 15.5" WC121P 16.0 21.5" 17.5" 17.75" 2.0 95.0 18.0" 8.0" 15.5" Multipurpose Chairs Arm pads Inside/Outside Overall Arm pad Base Diameter Outside Base Diameter Centerline Weight (Pounds) Molded seat WC111N 18.5"/24.5" 38.0" 9.5" 26.875 26.0 28.5 lbs. WC111P 18.5"/24.5" 38.0" 9.5" 26.875 26.0 28.5 lbs. FLEXNET seat WC121N 18.5"/24.5" 38.0" 9.0" 26.875 26.0 29.5 lbs. WC121P 18.5"/24.5" 38.0" 9.0" 26.875 26.0 29.5 lbs. Note: Some dimensions shown in this technical specification document differ from those shown in the Herman Miller ing Price Book because price book dimensions are derived from engineering drawings.

Caper Chairs 7 Multipurpose Stools Stools Depth Width Pan Angle -to- Angle Lumbar Support Width Molded WC7511N 23.5 33.5" 16.5" 17.5" 7.5 93.5 19.25" 10.5" 15.5" WC7511P 23.5 33.5" 16.5" 17.5" 7.5 93.5 19.25" 10.5" 15.5" FLEXNET WC7521N 23.5 33.5" 17.5" 17.75" 2.0 95.0 18.0" 8.0" 15.5" WC7521P 23.5 33.5" 17.5" 17.75" 2.0 95.0 18.0" 8.0" 15.5" Stools Arm pads Inside/Outside Overall Arm pad Base Diameter Outside Base Diameter Centerline Weight (Pounds) Molded seat WC7511N - 51.25" 9.5" 26.875 26.0 33.5 lbs. WC7511P 18.5"/24.5" 51.25" 9.5" 26.875 26.0 34.9 lbs. FLEXNET seat WC7521N - 51.25" 9.0" 26.875 26.0 34.7 lbs. WC7521P 18.5"/24.5" 51.25" 9.0" 26.875 26.0 36.1 lbs. Note: Some dimensions shown in this technical specification document differ from those shown in the Herman Miller ing Price Book because price book dimensions are derived from engineering drawings.

Caper Chairs 8 Stacking Chairs Stacking Chairs Depth Width Pan Angle -to- Angle Lumbar Support Width at Lumbar Overall Chair Width Molded WC410N 17.5" 16.5" 17.5" 11.5 95.4 18.75" 10.5" 16.0 24.25" WC410P 17.5" 16.5" 17.5" 11.5 95.4 18.75" 10.5" 16.0 24.25" FLEXNET WC420N 18.0 17.5 17.75" 4.5º 99.0º 18.0 8.0 16.0 24.25" WC420P 18.0 17.5 17.75" 4.5º 99.0º 18.0 8.0 16.0 24.25" Stacking Chairs Arm pads Inside/Outside Overall Arm pad Chair Footprint Weight (Pounds) Molded WC410N N/A 32.0" N/A 21.5"wx19.25"d 9.5 pounds WC410P 19.75 /24.5 32.0" 9.5" 21.5"wx19.25"d 10.5 pounds FLEXNET WC420N N/A 32.0" N/A 21.5"wx19.25"d 10.5 pounds WC420P 19.75 /24.25 32.0" 9.0" 21.5"wx19.25"d 11.5 pounds Note: Some dimensions shown in this technical specification document differ from those shown in the Herman Miller ing Price Book because price book dimensions are derived from engineering drawings.

Caper Chairs 9 Stacking Stools Stacking Stool Depth Width Pan Angle -to- Angle Lumbar Support Width Molded Counter (24 ) WC742410P 22.50 16.5" 17.5" 11.5 95.4 18.75" 10.5" 24.25" WC742410N 22.50 16.5" 17.5" 11.5 95.4 18.75" 10.5" 24.25" Bar (30 ) WC743010P 28.50 16.5" 17.5" 11.5 95.4 18.75" 10.5" 24.25" WC743010N 28.50 16.5" 17.5" 11.5 95.4 18.75" 10.5" 24.25" FLEXNET Counter (24 ) WC742420P 22.25 17.5" 17.75" 4.5 99.0 18.0" 8.0 24.25" WC742420N 22.25 17.5" 17.75" 4.5 99.0 18.0" 8.0 24.25" Café (30 ) WC743020P 30.25 17.5" 17.75" 4.5 99.0 18.0" 8.0 24.25" WC743020N 30.25 17.5" 17.75" 4.5 99.0 18.0" 8.0 24.25" height and overall height shown with standard glides. Stacking Stool Chair Description Armpads Inside/Outside Overall Armpad Chair Footprint Overall Depth Weight (lbs.) Molded Counter (24 ) WC742410P 19.75 /24.25 32.5" 9.5" 21.5 W x 21 D 18.75" *13.9 lbs. WC742410N 19.75 /24.25 32.5" 9.5" 21.5 W x 21 D 18.75" *13.9 lbs. Bar (30 ) WC743010P 19.75 /24.25 38.5" 9.5" 21.5 W x 22.25 D 18.75" *14.9 lbs. WC743010N 19.75 /24.25 38.5 9.5" 21.5 W x 22.25 D 18.75" *14.9 lbs. FLEXNET Counter (24 ) WC742420P 19.75 /24.25 32.5" 9.0" 21.5 W x 21 D 18.0" **15.2 lbs. WC742420N 19.75 /24.25 32.5" 9.0" 21.5 W x 21 D 18.0" **15.2 lbs. Bar (30 ) WC743020P 19.75 /24.25 38.5" 9.0" 21.5 W x 22.25 D 18.0" **16.2 lbs. WC743020N 19.75 /24.25 38.5 9.0" 21.5 W x 22.25 D 18.0" **16.2 lbs. *without arms **with arms Note: Some dimensions shown in this technical specification document differ from those shown in the Herman Miller ing Price Book because price book dimensions are derived from engineering drawings.

Caper Chairs 10 Multipurpose Chair Description WC111 WC121 This multipurpose chair has a molded, flexible back that is perforated and contoured. It has a biomechanical tilt mechanism that synchronizes the movement of the chair's seat and back, pneumatic seat-height adjustment, and 5-star base with casters. The chair has 2 seat options: the molded seat is perforated and contoured; the FLEXNET seat is suspension material. It is available with or without arms. All chairs meet CAL 133 requirements. The multipurpose chair is breathable and distributes the user's weight evenly. Each chair is lightweight and mobile and has a cutout in the back for easy movement. Construction and Molded The back and molded seat shall be injection-molded, glass-filled, textured, integral-color nylon. attaches to frame with lock fit between arm plug or arm support. The frame shall be made of 7/8 diameter tubular steel, and finished with a powder-coat paint. has molded-in handhold to assist user in moving or stacking of chair. FLEXNET The FLEXNET seat shall consist of an injection-molded, glass-filled polypropylene frame with locking pins to which the durable, breathable FLEXNET material (69% elastomer and 31% polyester) is attached. The FLEXNET material shall be a knitted blend of 69% elastomer and 31% polyester yarns. Snap fit cover of injection-molded, glass-filled polypropylene completes the seat assembly. At the seat s waterfall front edge, a cushioning insert of molded urethane foam shall be fitted between the FLEXNET material and the seat frame. Arms (Optional) Arms shall be self-skinning urethane with a cast steel insert. Arms can be added or removed on site. (See Herman Miller Service Parts Information.) Base The 5-star base shall be die-cast aluminum, with a powder-coat epoxy finish. The chair shall swivel 360 degrees. The base shall house a unitized pneumatic seat height adjustment mechanism contained in 2 steel tubes; an inner tube shall slide and rotate in an Acetal bushing within an outer tube. The outer tube shall be coated in black and shall have a tapered end that will be pressed into the base and an upper end that will be pressed into the tilt mechanism. See Adjustments for seat height ranges. Chairs shall be furnished with interchangeable casters. See the Casters and Glides section for additional information.

Caper Chairs 11 Multipurpose Chair Adjustments Adjustments Continued height shall be controlled by an injection-molded push button attached to a steel lever and located on the chair s right front side. The approximate seat height range shall be 16 to 21 ½. Tilt The bio-mechanical, synchronous tilt mechanism shall be comprised of a 2 3/8 coiled steel compression spring, a gear-driven tension adjustment and a die-cast aluminum housing finished in powder-coat epoxy to match base. The tilt-tension adjustment lever shall extend from the right side of the tilt and shall be steel, with a powder-coat epoxy finish. A textured, molded tilt-tension knob shall be pressed onto the lever. The tilt shall allow the user s body to recline to support a range of postures, pivoting at the ankles, knees and hips. The back-to-seat ration shall be 2:1 when the chair is reclined from a neutral angle. The chair will have a total reward recline of 16 degrees. Performance Data This chair is tested and warranted for use by people 300 pounds and under. This chair shall meet CAL 133 fire code requirements.

Caper Chairs 12 Stacking Chair Description WC4 This stacking chair has a tubular steel frame, a molded back that is perforated and contoured, and a 4-leg base with glides or casters. It has 2 seat options: the molded seat is perforated and contoured; the FLEXNET seat is suspension material. Each chair is breathable and distributes the user s weight evenly. All chairs meet CAL 133 requirements. The chair is lightweight and mobile. The molded seat chair without arms weights 9.5 lbs. for the and 10.5 lbs. with arms, and the FLEXNET chair without arms weights 10.5 lbs. and with arms 11.5 lbs. All styles of this chair can be stacked up to 6 high on the floor. Construction and Molded The stacking stool shall have a seat and a back of textured, integral color, injection-molded, glass-filled polypropylene. attaches to frame with lock fit between arm plug or arm support. The back shall have a molded-in handhold to assist users in moving or stacking the stool. FLEXNET The FLEXNET seat shall consist of an injection-molded, glass-filled polypropylene frame with locking pins to which the durable, breathable FLEXNET material (69% elastomer and 31% polyester) is attached. The FLEXNET material shall be a knitted blend of 69% elastomer and 31% polyester yarns. Snap fit cover of injection-molded, glass-filled polypropylene completes the seat assembly. At the seat s waterfall front edge, a cushioning insert of molded urethane foam shall be fitted between the FLEXNET material and the seat frame. Arms (Optional) The stacking stool shall be available without arms or with fixed arms. Arm support shall be diecast aluminum finished with powder-coat epoxy. Armpads shall be made from Hytrel synthetic rubber. Arms can be added or removed on site. (See Herman Miller Service Parts Information.) Frame The stool frame shall be high-strength, low-alloy (HSLA), 7/8 diameter, 16-gauge tubular steel and shall be finished with powder-coat epoxy. Four Santoprene bumpers shall be attached to the frame to ensure proper stacking. Chairs shall be furnished with interchangeable glides and casters specific to floor surface treatment. See the Casters and Glides section for additional information. Performance Data The stool will be rated for 300 pounds. This stool shall meet CAL 133 fire code requirements.

Caper Chairs 13 Stacking Stool Description WC74 This stool has a tubular steel frame, a molded back that is perforated and contoured, and a 4- leg base with glides. It has 2 seat options: the molded seat is perforated and contoured; the FLEXNET seat is suspension material. Each stool is breathable and distributes the user s weight evenly. The stool is available with or without arms. All chairs meet CAL 133 requirements. The stool is lightweight and mobile. The molded seat stool without arms weights 13.9 lbs. for the counter height and 14.9 lbs. for the bar height, and the FLEXNET stool with arms weights 15.2 lbs. for the counter height and 16.2 lbs. for the café height. All styles of this stool can be stacked up to 5 high on the floor. Construction and Molded The stacking stool shall have a seat and a back of textured, integral color, injection-molded, glass-filled polypropylene. attaches to frame with lock fit between arm plug or arm support. The back shall have a molded-in handhold to assist users in moving or stacking the stool. FLEXNET The FLEXNET seat shall consist of an injection-molded, glass-filled polypropylene frame with locking pins to which the durable, breathable FLEXNET material (69% elastomer and 31% polyester) is attached. The FLEXNET material shall be a knitted blend of 69% elastomer and 31% polyester yarns. Snap fit cover of injection-molded, glass-filled polypropylene completes the seat assembly. At the seat s waterfall front edge, a cushioning insert of molded urethane foam shall be fitted between the FLEXNET material and the seat frame. Arms (Optional) The stacking stool shall be available without arms or with fixed arms. Arm support shall be diecast aluminum finished with powder-coat epoxy. Armpads shall be made from Hytrel synthetic rubber. Arms can be added or removed on site. (See Herman Miller Service Parts Information.) Frame The stool frame shall be high-strength, low-alloy (HSLA), 7/8 diameter, 16-gauge tubular steel and shall be finished with powder-coat epoxy. Four Santoprene bumpers shall be attached to the frame to ensure proper stacking. Chairs shall be furnished with interchangeable glides, specific to floor surface treatment. See the Casters and Glides section for additional information. Performance Data The stool will be rated for 300 pounds. This stool shall meet CAL 133 fire code requirements.

Caper Chairs 14 Multipurpose Stool Description WC751 WC752 The stool have a molded, flexible back that is perforated and contoured. It has a biomechanical tilt mechanism that synchronizes the movement of the stool's seat and back, pneumatic seatheight adjustment, and 5-star base with casters. The stool has 2 seat options: the molded seat is perforated and contoured; the FLEXNET seat is suspension material. It is available with or without arms. All chairs meet CAL 133 requirements. The multipurpose stool is breathable and distributes the user's weight evenly. Each stool is lightweight and mobile and has a cutout in the back for easy movement. Construction and Molded The back and molded seat shall be injection-molded, glass-filled, textured, integral-color nylon. attaches to frame with lock fit between arm plug or arm support. The frame shall be made of 7/8 diameter tubular steel, and finished with a powder-coat paint. has molded-in handhold to assist user in moving or stacking of chair. FLEXNET The FLEXNET seat shall consist of an injection-molded, glass-filled polypropylene frame with locking pins to which the durable, breathable FLEXNET material (69% elastomer and 31% polyester) is attached. The FLEXNET material shall be a knitted blend of 69% elastomer and 31% polyester yarns. Snap fit cover of injection-molded, glass-filled polypropylene completes the seat assembly. At the seat s waterfall front edge, a cushioning insert of molded urethane foam shall be fitted between the FLEXNET material and the seat frame. Arms (Optional) Arms shall be self-skinning urethane with a cast steel insert. Arms can be added or removed on site. (See Herman Miller Service Parts Information.) Base The 5-star base shall be die-cast aluminum, with a powder-coat epoxy finish. The stool shall swivel 360 degrees. The base shall house a unitized pneumatic seat height adjustment mechanism contained in 2 steel tubes; an inner tube shall slide and rotate in an Acetal bushing within an outer tube. The outer tube shall be coated in black and shall have a tapered end that will be pressed into the base and an upper end that will be pressed into the tilt mechanism. See Adjustments for seat height ranges. Stools shall be furnished with interchangeable casters. See the Casters and Glides section for additional information.

Caper Chairs 15 Multipurpose Stool Adjustments Adjustments Continued height shall be controlled by an injection-molded push button attached to a steel lever and located on the stool s right front side. The approximate seat height range shall be 23 ½ to 21 ½. Tilt The bio-mechanical, synchronous tilt mechanism shall be comprised of a 2 3/8 coiled steel compression spring, a gear-driven tension adjustment and a die-cast aluminum housing finished in powder-coat epoxy to match base. The tilt-tension adjustment lever shall extend from the right side of the tilt and shall be steel, with a powder-coat epoxy finish. A textured, molded tilt-tension knob shall be pressed onto the lever. The tilt shall allow the user s body to recline to support a range of postures, pivoting at the ankles, knees and hips. The back-to-seat ration shall be 2:1 when the chair is reclined from a neutral angle. The chair will have a total reward recline of 16 degrees. Performance Data This stool is tested and warranted for use by people 300 pounds and under. This chair shall meet CAL 133 fire code requirements.

Caper Chairs 16 Cart Description WC904 This cart stores and transports up to 15 Caper stacking chairs (total stacked height of 68 ). It has molded-in handles and 4"-diameter casters: 2 swivel and 2 rigid. The cart is single-piecemolded construction that ships fully assembled. Finish is black. Dimensions Width Length 17 28 1/4 42 3/4 Construction Body The cart body shall be of a single piece, thermoformed, black ABS plastic construction with molded-in handles. Casters Cart has four, 4"-diameter nylon casters, 2 that swivel and 2 that are fixed for control and steering.

Caper Chairs 17 Casters & Glides Multipurpose Size Type Materials Use Chair & Stool (Diameter) BB 2 1/2" hard double wheels black nylon yoke and wheels carpet only C7 2 1/2 soft double wheels black nylon yoke and wheels, soft polyurethane tread hard floors or carpet C9 2 1/2 soft double wheels, braking GF (Glide, Stool Only) black nylon yoke and wheels, soft polyurethane tread, internal brake 2 1/2 black nylon stem and steel-plated swivel hard floors or carpet hard floors or carpet Stacking Chair Size (Diameter) Type Materials Use U4 1 7/8 hard, double wheel black nylon yoke and wheels carpet only U5 1 7/8 soft, double wheel black nylon yoke and wheels, with hard floors or carpet urethane tread Y7 (Glides) 1 7/8 black acetal carpet only YX (Glides) 1 7/8 black nylon stem and steel-plated swivel foot with floor saver glide insert hard floors only Stacking Stool Size (Diameter) Type Materials Use Y7 (Glides) 1 7/8 black acetal carpet only YX (Glides) 1 7/8 black nylon stem and steel-plated hard floors only swivel foot with floor saver glide insert