GAN Electronic 600W/750W SE US

GAN Electronic 600W/750W SE US. Introduction Thank you for purchasing the GAN Electronic 600 W / 750 W SE US. This manual describes the mounting and installing of the product and also describes how to use the product. Mounting and installing of the fixture may only be executed by certified service personnel. Please read and understand this manual completely before using the product. Only use the product as specified in this manual... Used symbols Warning! A warning indicates severe damage to the user and/or product may occur when a procedure is not carried out as described. Caution! A caution sign indicates problems may occur if a procedure is not carried out as described. It may also serve as a reminder to the user. Note: A note gives additional information, e.g. for a procedure. This symbol indicates that the reflector and lamp can reach very high temperatures (>85 Celsius / >85 Fahrenheit). Observe a cool down period before performing maintenance. This symbol is an internationally recognized symbol used to designate recyclable materials. This symbol shows that a product has been independently tested and certified to meet recognized standards for safety or performance. The symbol on the material, accessories or packaging indicates that this product may not be discarded as household waste. By disposing of the equipment in the proper way, you will be helping to prevent possible risks to the environment and public health, which might otherwise be caused by improper handling of the discarded equipment. Recycling of materials contributes to the conservation of natural resources. Therefore, please do not dispose of your old electronics and electrical appliances via household waste. A This symbol indicates the minimum distance (B) between the fixture (A) and the lit surface. B 2. Product description The GAN Electronic 600 W / 750 W SE US is an electronic horticultural fixture. It can be used to drive a single ended high frequency type (electronic) high pressure sodium lamp: 600 W SE US: Recommended lamps: Gavita Pro 600 W Electronic HPS E40. Philips Master GreenPower Plus 600 W EL. 750 W SE US: Recommended lamps: Gavita Pro 750W Electronic HPS. The GAN Electronic 600 W / 750 W SE US is intended to be used in greenhouses or in climate rooms. In this manual, the GAN Electronic 600 W / 750 W SE US will be referred to as: the fixture. 3. Product information and specifications 3.. General product information Product name GAN Electronic 600 W SE US GAN Electronic 750 W 400 V SE US Manufacturer Gavita Nederland bv Gavita Nederland bv Version 240V-277 V 277 V 400 V 277 V 400 V EAN Code 878692230002 878692230200 878692230095 87869223049 Part number.65.9.04.06 4.63.9.04.0.65.9.04.07 4.74.9.04.05 Plug type Wieland RST20i3 Wieland RST20i3 Wieland RST20i3 Wieland RST20i3 Wieland RST20i3

Product name GAN Electronic 600 W 347 V CAN GAN Electronic 750 W 347 V SE CAN Manufacturer Gavita Nederland bv Gavita Nederland bv Version 347 V 347 V EAN Code 878692230309 Part number 4.64.9.04.0 Plug type Wieland RST20i3 Wieland RST20i3 3.2. Technical specifications Product name GAN Electronic 600 W SE US GAN Electronic 750 W 400 V SE US Input voltage +/-0% 240V-277 V 277 V 400 V 277 V 400 V Input wattage +/-3% 632 W 635 W 632 W 795 W Apparent power +/-3% 648 VA 652 VA 645 VA 8 VA Input current at 00% 2,29 A 2,35 A,58 A 2,9 A 2,03 A Inrush current: 34 A /,6 msec 7 A 34 A /,6 msec 30 A Product weight 3,5 kg / 7.7 lbs 3,5 kg / 7.7 lbs 3,5 kg / 7.7 lbs 3,4 kg / 7.5 lbs 3,4 kg / 7.5 lbs Ignition voltage: 4 kv 3,5 kv Product name GAN Electronic 600 W 347 V CAN GAN Electronic 750 W 347 V SE CAN Input voltage +/-0% 347 V Input wattage +/-3% 640 W Apparent power +/-3% 653 VA Input current at 00%,86 A 2,3 A Inrush current: 20 A Product weight 3,5 kg / 7.7 lbs 3,4 kg / 7.5 lbs Ignition voltage: 4 kv 3,5 kv Dimensions (LxWxH) 54,5x25,4x20,9 cm / 2.5x0x8,2 in. (height excl. mounting hooks) Temperature case 75 Celsius / 67 Fahrenheit Temperature ambient 0 ~ 35 Celsius / 32 ~ 95 Fahrenheit Power factor > 0,98 Total Harmonic Distortion < 0% Frequency 48-63 Hz Certification c CSA us Insulation Class - requires an earth connection Power inlet Wieland RST20i3 IP65 connector Earth leakage current: A 3.3. Compatible products and accessories Product name Gavita part number Replacement reflectors Gavita HR96 SE 30.46.02.0 Gavita MD 29 SE 30.07.3.08 Gavita Pro 600 W Electronic HPS 26.64.40.02 Compatible lamps Philips Master GreenPower Plus 600 W EL 400V E40 2.64.6.2 Philips Master GreenPower Plus 600 W EL 400V E39 Mogul 6.64.6.23 Gavita Pro 750 W Electronic HPS 27.74.40.33 Compatible cable plug Wieland RST20i3 female connector 60.70..7 3.4. Environment The product is intended to be used in greenhouses and climate rooms. The product can be used in damp environments. The product may not be used in wet environments or outdoors. The Gavita Pro 600 W Electronic HPS lamp, the Philips Master GreenPower Plus 600 W EL 400 V lamp and the Gavita Pro 750 W Electronic HPS lamp function optimal when the ambient temperature is between 20 ~ 30 C / 68 ~ 86 Fahrenheit. 3.5. Legal CSA approved according to: 252952.

4. Safety recommendations and warnings Warning! Carefully read the warnings below before using or working with the product! Always adhere to the local rules and regulations when installing or using the fixture. Do not open or disassemble the fixture, it contains no servicable parts inside. Opening the fixture can be dangerous and will void the warranty. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45-30 MHz. Do not use the fixture when either its lamp or its power cord are damaged. Replace the power cord only with original certified cords. Replace the lamp only with lamps specified by Gavita (see paragraph 3.3). The use of other lamps may damage the product and lamp and will void the warranty. Modifications to the cords can lead to unwanted electromagnetic effects, which makes the product not comply with legal requirements. Do not expose the fixture to: condensing humidity, heavy mist, fog or direct spray; (ambient) temperatures outside the specified range; dust and contamination; direct sunlight during use or HID light that could heat up the ballast. Always disconnect the fixture from mains before performing any maintenance. Always allow for a cool down period of at least 30 minutes before touching the lamp or reflector. Touching the lamp or the reflector when the lamp is lit or immediately afterwards will result in severe burns! Never touch the lamp with bare hands as this will cause damage to the lamp. Do not use the fixture near flammable, explosive or reactive substances. The lamp and the reflector of the fixture reach temperatures of >85 Celsius. Do not use sulfur vaporizers or water misters. Sulfur and calcium deposits on your reflector will decrease its efficiency. The installation and use of the fixture is the responsibility of the end user. Incorrect use or installation can lead to failure and damage to the fixture. Damage to the fixture and electronic circuitry as a result of incorrect installation and use revokes the warranty. 5. Contents () A. GAN Electronic 600 W / 750 W SE US. Electronic ballast 2. Lamp bracket 3. Lever to unlatch reflector 4. Lamp socket 5. Reflector Ecomax HR96 SE* 6. Mounting points *The reflector is delivery dependent, it may differ from the image B. Wieland RST20i3 female connector C. Gavita Pro 600 W Electronic HPS lamp / Philips Master GreenPower Plus 600 W EL lamp / Gavita Pro 750W Electronic HPS lamp D. Power cord 6. Controls, connections and indications (2) A. Wieland RST20i3 male connector. Ground connection 2. Phase / neutral connections B. Status LED. A B A6 A A4 A A5 A6 A2 A3 BC A2 CD Gavita HR96 SE Gavita MD 29 SE Wieland RST20i3 2. B

7. Installation Warning! Mounting and installing of the fixture may only be executed by certified service personnel, in accordance with the applicable local laws and regulations. Warning! The fitter is responsible for correct and safe installation. Warning! Ensure the local cabling can support the voltage and current requirements of the fixture. Warning! Avoid coiled cords and keep mains leads separated. This prevents electromagnetic interference. Warning! Do not connect or disconnect the Wieland RST20i3 plug under load. B B3 B2 7.. Installation preparations Switch off mains power. Read the Gavita light distribution plan. If not done already, install the lamp in the fixture (see paragraph 0.2). If not done already, screw the mounting point into the fixture (3). 3. 7.2. Installing the fixture Mount the suspension bracket* according to the light distribution plan. Hang the fixture by its two mounting points onto the suspension bracket (4). The two mounting points are spaced 30-32 cm /.8-2.59 inches apart. Caution! Always hang the fixture horizontally. Adjustments can be made by screwing the mounting point in or out. B To install other fixtures, repeat the steps at paragraph 7. and 7.2. * The suspension bracket is delivery dependent, it may differ from the image. B2 600W 750W 24 in 30 in 4.

7.3. Connecting the fixture to the mains Warning! Make sure mains power is switched off. Warning! Always install the lamp before connecting the fixture to the mains. Warning! Ensure the cord is not coiled and does not touch any hot surfaces. Warning! Connect the cables according to local rules, safety regulations and electrical code. Warning! Ensure external switching gear can cope with the inrush current of the fixture (see paragraph 3.2). Always use a double throw contactor suitable for switching a capacitive load. Never use household timers to switch the fixture! Note: A power cord is not included in the package. If not done already, remove the top part of Wieland RST20i3 female connector from the bottom part (5). Pull the mains cable through the bottom part (6). Strip the wiring (7). The insulation strip length is 8 mm / 0.3 and the dismantling length is 32 mm /.26. Connect the wiring to the top part connections (8). N = Neutral (Phase at 400 V models). L = Phase. = Ground. Slide the top part into the bottom part and tighten the gland nut (9). Note: When the parts connect correctly, you will hear a CLICK sound. Plug the Wieland RST20i3 female connection onto the Wieland RST20i3 male connection on the fixture (0). Switch on mains power. Warning! Do not connect or disconnect the Wieland RST20i3 plug under load. 5. 2 6. 32 mm /.26 8 mm / 0.3 N/L 7. 2 2 8. 9. 0.

8. Precautions when using the fixture Warning! Never use the fixture without a lamp or reflector! Warning! Always wait 20-30 minutes for the reflector to cool down! 9. Troubleshooting using the status LED Note: The status LED is not present on all models. The status LED provides information on the condition of the lamp. Consult table to interpret the status LED. LED signals are represented by colored red dots. 9.. Status indications Status LED message Status fixture Description Action/Solution No error The lamp is working correctly No action required. EOL timer expired Cycle error Maximum number of ignition attempts done without succesfull ignition or a driver is locked or has failed Maximum number ignition attempts done (lamp stopped for unknown reason) Low mains Mains voltage too low Reset mains cycle manually. If the problem persists, it could be the end of the lamp s lifecycle. Replace the lamp Check the lamp. Replace the lamp when damaged Check the voltage, mains cycle automatically resets Thermal overload Maximum driver temperature exceeded Reset mains cycle manually Lamp voltage out of range Lamp voltage too low, lamp voltage too high or DC shift detected This could be the end of the lamp s lifecycle. Replace the lamp High mains Mains voltage too high and/or DC-bus voltage too high Check the voltage, mains cycle automatically resets Ignition busy Ballast is trying to ignite the lamp No action required. Table Legend LED message Time 256 ms. 52 ms.

0. Inspection, maintenance and repair Warning! Disconnect the product from mains before performing any maintenance or repairs. Warning! Do not connect or disconnect the Wieland RST20i3 plug under load. Warning! Do not open or disassemble the fixture, it contains no servicable parts inside. Opening the fixture can be dangerous and will void the warranty. Warning! Always allow for a cool down period of at least 30 minutes before touching the lamp or reflector. Caution! Do not clean the fixture with detergents, abrasives or other agressive substances. Caution! Do not touch the inside of the reflector. Note: Gavita recommends to measure the lamp and reflector for aging every year. Replace the lamp and/or reflector when they are aged. B2 B Regularly check the fixture for dust or dirt buildup. Clean if necessary. Contamination may couse overheating and decreased performance. Clean the inside of the reflector with soapy water, but use demineralised water to rinse the reflector; Clean the electronic ballast and the outside of the fixture using a dry or damp cloth. Check the lamp monthly for discolorations or black markings. Always replace a damaged lamp. Note: Before initial use, the lamp could have black markings. This will disappear when the lamp runs on full power. If not, replace the lamp. Regularly check the wiring of the product to ensure it is undamaged.. 2 0.. How to disconnect the Wieland RST20i3 plug Warning! Do not connect or disconnect the Wieland RST20i3 plug under load. Switch off mains power. Press the pin on the Wieland RST20i3 male connection downwards and pull the Wieland RST20i3 female connection from the fixture (). 2. 0.2. Placement and replacement of the lamp Warning! Always allow for a cool down period of at least 30 minutes before touching the lamp or reflector. Caution! Do not touch the lamp with bare hands as this will damage the lamp. Always use a fabric glove to handle the lamp. Caution! Only use lamps specified by Gavita (see paragraph 3.3). Note: Gavita recommends replacing the lamp after 0000 lighting hours. Note: Loosen the reflector (see paragraph 0.3) if there are any problems with removing or placing the lamp. 2 Switch off mains power. Use a fabric glove to carefully unscrew the lamp from the socket (2). Use a protective glove if the lamp is damaged. Use a fabric glove to carefully screw a new lamp into the socket (3). Switch on mains power. 3.

0.3. Placement and replacement of the reflector Warning! Always allow for a cool down period of at least 30 minutes before touching the lamp or reflector. Note: Gavita recommends replacing the reflector* after 0000 lighting hours. Depending on the environment and contamination levels the reflector will degrade. The vega/miro aluminum can be cleaned with soapy water, but we recommend to change the reflector every two to four years. Also replace the lamp when replacing the reflector. * The reflector is delivery dependent, it may differ from the image. Switch off mains power. Remove the lamp from the fixture (see paragraph 0.2). Support the reflector on the side of the reflector lever to prevent it from falling (4). Move the reflector lever up to retract the two pins holding the reflector in place (5). Remove the reflector (6). Place the new reflector. Ensure the reflector lever is in the opened position to allow the reflector to pass. Ensure the holes in the reflector are aligned with the pins in the fixture (7). Release the reflector lever so its two pins hold the reflector in place. Insert the lamp in the lamp holder (see paragraph 0.2). Switch on mains power.. Storage and disposal Store the fixture in a dry and clean environment, with an ambient temperature of -20 ~ 85 Celsius. The product must not be discarded as unsorted municipal waste, but must be collected separately for the purpose of treatment, recovery and environmentally sound disposal. Caution! The lamps are chemical hazardous waste and must be delivered to the designated authorities. Caution! The lamp contains mercury. 2. Warranty The warranty conditions are delivery dependent and can be found on a separate sheet. 4. 5. 6. 7. Manual: GAN Electronic 600 W / 750 W SE US Changes reserved - Version 5/47 Gavita Nederland bv Oosteinderweg 27 432 AH Aalsmeer The Netherlands Tel: +3(0)297-380 450 Fax: +3(0)297-380 45 E: info@gavita.nl W: www.gavita.nl Gavita Canada inc. 360 York Road, Unit 3 & 4 Glendale Industrial Mall Niagara-on-the-lake Ontario L0S J0 Tel: + 905 988 3590 Fax: + 905 988 367 E: info@gavita.ca W: www.gavita.ca