MAINTENANCE SPECIFICATIONS LEGISLATION WARRANTY

Transcription

1

2 CONGRATULATIONS ON YOUR PURCHASE OF THE OCL COMPLETE FIXTURE. OCL lighting provides high quality lighting by integrating experience, creative sensibility and innovation in our products. By combining pragmatism, perfectionism and high technical standards in the design and lay-out work, we are able to reach truly unique results. OCL lighting systems are the new industrial standard in professional high output fixtures. Light quality is a major focal point in the industry and the OCL X series has been designed to fulfill that specific need. The systems support both HPS & Metal halide lamps.the OCL double-ended (DE) HPS lamps are proven to be extremely high in Par output, with a broader spectrum than traditional HPS lamps and only a 5% loss of light at hours in operation. All of our ballasts come standard with PowerControl, StartSmart and dimming feature. The OCL X series are the next level in professional fixtures, with the ability for central control with the OCL controllers. With OCL lighting systems You are in control of the light! UNIQUE TECHNOLOGY Power Control : OCL s Power Control is a software based technology that allows one -at- a -time sequential lamp ignition. No matter how many OCL ballasts you are running, your lights will ignite one -at- a - time. By utilizing a staggered ignition, OCL ballasts prevent huge current draws/spikes in your electrical system and is therefore a more efficient means of lighting your garden. Start Smart Technology: When the ballast is powered on, OCL ballasts will send a mv signal through the closed circuit (between ballast and lamp), to determine a variety of different factors such as: lamp type, open/short circuits, high/low temps and thermal issues, ignition failure, over flow current, and end of lamp life. World s Lowest THD%: With an input Total Harmonic Distortion (THD) value of and an output THD% of <12%, OCL digital ballasts provide the cleanest signal for HID lamps. This provides maximum output, spectral perfection, and longevity of your equipment. INSTALLATION OCL digital ballasts can be positioned universally. The unique design of the heat sink dissipates heat away from the critical components in the ballast. OCL digital ballasts are designed for use indoors and are sealed against damage by humidity and dust. When installing your complete fixtures, we recommend to use up to 80% maximum load of your breaker capacity for electrical safety. LAMP CONNECTIONS Never turn on the ballast without the lamp cord and lamp installed. Never disconnect the lamp from a live ballast. Hot restrike: it is very important to allow the lamp to cool before attempting to reignite. Please allow minutes before restarting to avoid damage to the lamp. Ensure a snug fit when installing lamps. Make sure the mogul socket shows no signs of damage or corrosion. Confirm that power has been disconnected from the ballast before attempting to change lamps. COMPATIBLE LAMPS OCL digital ballasts operate both Metal Halide (MH) and High Pressure Sodium (HPS) lamps. While OCL digital ballasts are compatible with a majority of brand name lamps, OCL digital lamps are recommended. Our technical engineers tune and match our light systems together for optimal output and spectral balance. Using a matched OCL system has significant benefits over unmatched systems in terms of light quality and longevity. Please make sure the proper wattage lamp is installed before adjusting ballasts to full power or boost mode. OCL digital ballasts have soft start integration, ballasts ease up to full draw. OCL ballasts utilize soft dimming, power will ease up to full draw. It may take a few minutes for the ballast to dim from each setting. Visible dimming may not be noticeable to the human eye. MAINTENAN OCL digital ballasts are not self-servicable. Disassembling the ballast will void the warranty. The internal componentry of the ballast is sealed with a resin to protect the electronics. The aluminum exterior of the ballast can be cleaned with a damp cloth, however make sure the ballast is disconnected before cleaning. Checking all connections regularly to make sure that no cables have become loose or show signs of damage. TROUBLESHOOTING In case the HID lamp will not start, you can try the possible fixes below: Lamp is loose in socket Incorrect voltage Defective or poor wiring Poor electrical connections Incorrect or damaged lamp POSSIBLE FIXES OR CORRECTIVE MAINTENAN: Make sure you are using the correct voltage input. Examine wiring to confirm proper connections. Verify that you are using the proper voltage lamp, use OCL digital lamps for best results. Check to make sure there is no lamp damage, sometimes lamps are installed too firmly, look for broken connections. SPECIFICATIONS Voltage Frequency Current consumption Rated Power Power Factor THD Input Connection Operating Temp Case Temp Certification External dim External dim connector LEGISLATION LVD approval according to: EN :2015,EN :1989,EN :2015,EN :2005+A1:2010,EN 62493:2015. EMC approval according to: EN 55015:2013+A1:2015,EN 6-3-2:2014,EN 6-3-3:2013,EN 61547:2009 WARRANTY W W W 2.7A (at 100%) 621W (at 100%) 3.4A (at 100%) 785W (at 100%) OCL warrants that our complete fixtures are free from manufacturer defects in electronics and mechanical craftsmanship when used under normal operating conditions for 3 years from manufacture date. If the product shows signs of defect within this period and which is not due to user error, OCL shall, at its discretion, either replace or repair the product. In case a replacement is required, a limited warranty will apply to the replacement product for the remaining initial warranty period. For warranty service, please return the ballast to your retail store together with the original sales receipt. 4.4A (at 100%) 1048W (at 100%) Accessories included: Power cord, 1 RJ45 interlink cable for plug and play installation, OCL electronic lamp

3 DOUBLE ENDED LAMP INSTALLATION REPLAMENT OF THE REFLECTOR PLEASE READ INTRUCTIONS BEFORE INSTALLATION Warning: Keep the reflector away from combustible materials. Ensure your reflector is mounted securely and keep lamp cords away from direct heat from both lamp and reflector. Light hangers or small chains are good options to use for hanging the reflector. Changing Lamps: Let the reflector cool down and disconnect the power from the ballast when replacing or changing out lamps. Use gloves to keep the lamp glass clean from dirt and oils. TO REMOVE A LAMP Disconnect the power from the ballast Remove holder cap [A] Open the lamp holders by sliding them outwards, the lamp will be held in place by a metal spring, however secure the lamp to prevent it from falling out [B] Note: OCL recommends replacing the reflector after 5000 lighting hours. Depending on the environment and contamination levels the reflector will degrade. The V53 Hammertone/Concave aluminum can not be cleaned without damage. Therefore we recommend to changing the reflector once every year. Also replace the lamp when replacing the reflector. Switch off mains power. Remove the lamp from the fixture. Support the reflector on the side of the reflector lever to prevent it from falling. Move the pin to the left. Remove the reflector. Place the new reflector. Ensure the reflector lever is in the opened position to allow the reflector to pass. Ensure the holes in the reflector are aligned with the pins in the fixture. Release the reflector lever so its two pins hold the reflector in place. Insert the lamp in the lamp holder. Switch on mains power. TO INSTALL A NEW LAMP Make sure power is disconnected from the ballast Confirm the lamp is clean, wear cotton gloves if possible Confirm the end wires are straight Remove holder cap [A] Open lamp holders by sliding them outwards [B] Install the lamp by gently pressing the lamp until the metal springs hold the lamp [C] Close the lamp holders by sliding them inward [D] Important: Finally? Install the spring at the back of the Holder Cap and prevent any loosening. [A] Wipe the lamp with a clean soft cloth. *Do not touch the reflective material with your bare hands

4 COMPATIBLE PRODUCTS OCL lamps qualify as one of the highest output double ended lamps on the market and have an incredible depreciation rate of 5% at hours. OCL double ended lamps feature premium quartz glass for enhanced spectrum and penetration of your plants which results in higher quality and yield. OCL lamps contain enhanced UV-spectra. Exercise caution when working around any HID lamp that contains UV, always wear protective glasses. 2K GREENPOWER - HPS De OCL 2K GreenPower HPS is optimal for the blooming phase. OUTPUT Lamp color: 2K Lamp type: High pressure sodium 30,03 INPUT 4K DAYLIGHTPOWER - MH The OCL X series, with extremely powerful and higher PAR output than traditional fixtures, ask for a smart controller. That is why OCL designed the world s smartest and yet easy to operate lighting controller. All sensors (TEMP/RH/CO2) can be calibrated, it detects sensor failures and when a connection is not set-up properly a warning will automatically be displayed. OCL 4K Daylight Power Metal Halide is a pulse-start full spectrum light, used for all stages of growth and bloom. Lamp color: 4K The OCL DLC 1.1 Smart Lighting and CO2 Controller includes a built-in clock and back-up battery with a 30-year lifetime. The DLC 1.1 simulates natural growing conditions with the RISE/FALL option, allowing plants to gradually warm up and cool down. The AUTO-SAVE TEMP option senses when indoor temperatures are getting too high and responds by automatically dimming the connected lamps, thereby reducing or even avoiding environmental stress and crop damage. The SHUTDOWN-TEMP is an extra safety feature that will shut down all lighting in the room when the temperature is not reducing after the Auto-Save Temp has set in. Causes could be a malfunctioning extraction or climate control unit. 6K BLUEPOWER - MH OCL 6K Blue Power Metal Halide is the best spectrum used for vegetative growth to encourage shorter node spacing and bushier plants. Lamp color: 6K A manual resetting of the SHUTDOWN TEMP is then required to restart the system. With the CO2 SET ppm option, the controller not only manages the lights but the CO2 generators and cool CO2 installations can be controlled also. When using an OCL DLC1.1 controller, no additional switch board is required. With the AUX BOX, to be ordered separately, it is possible to connect a dehumidifier, extra ventilation or heating. The AUX BOX is equipped with a RJ12 UTP connection and a 16A relay for 3.5KW controlled power. 10K FINALPOWER - MH OCL 10K Final Power Metal Halide is used for the last 7 14 days of bloom to allow for better ripening and finishing. Lamp color: 10K NEVER BEFORE WAS IT SO SIMPLE TO CREATE THE RIGHT CLIMATE FOR YOUR PLANTS! AVAILABLE IN // Watt

5