TROL PNEUMTIC CONTROL VLVES PV16 ON-OFF (V16 globe valves series with linear actuators P series) DESCRIPTION The PV16G ON-Off valves are single seated, two-way body constructed with in-line straight connections. The P pneumatic actuator is rubber diaphragm and multi-springs. Its action can be D -direct action (air to close) or R-reverse action (air to open). Their wide application ranges allows to use this valve with the most common process fluids such as water, superheated water, steam, air, gas and other non corrosive fluids. MIN FETURES Single seated, two ways, direct or reverse action valve.valve top flange permanently attached to the body, removal is unnecessary for replacing the actuator. Soft sealing as standard. OPTIONS: USE: ir filter regulator Top-work manual handwheel Stainless steel construction. Saturated and superheated steam. Hot and superheated water. ir, gases and other noncorrosive fluids. VLVE BODY LIMITING CONDITIONS PV16G-OF Press. Temp. 16 bar -10 / 120ºC 15,5 bar 150ºC 14,7 bar 200ºC 13,9 bar 250ºC 12,8 bar 300ºC PV16I-OF Press. Temp. 16 bar -10 / 100ºC 14,5 bar 150ºC 13,4 bar 200ºC 12,7 bar 250ºC 11,8 bar 300ºC VILBLE MODELS: PV16G-OF - Nodular iron MX. IR SUPPLY PV16I-OF - Stainless steel PRESSURE: VLVE : DN15 to DN100 MBIENT TEMPERTURE: -20ºC...+70ºC CONNECTIONS: Flanged EN1092-2 PN16 BONNET : From -5ºC to +220ºC (standard) Finned for temperature >220ºC CTUTORS: P-205; P-280; P-340; P-435 (from DN32 to DN100) STEM SELING: PTFE/GR V-Rings - up to 220ºC CTUTOR CONN: 1/4'' NPT-F (Standard bonnet) PLUG TYPES: On-Off (PT) PORT: Full port HOW TO SELECT: Never size the valve according to the pipe diameter in which it has to be fitted but according to the required actual flow of steam or water.refer to valve calculation data sheet or consult the factory. CE MRKING (PED - European Directive 97/23/EC) PN 16 Category DN15 to DN50 SEP - art. 3, paragraph3 DN65 to DN100 1 (CE Marked) VLSTEM IS PV16OF.70 E 10.06
DN DIMENSIONS - VLVE BODY (mm) B (mm) STD. C (mm) BONNET EXT. 15 130 48 80 150 20 150 53 80 150 25 160 58 85 165 32 180 70 90 170 40 200 75 105 185 50 230 83 105 195 65 290 93 165(195) 265(295) 80 310 100 175(205) 270(300) 100 350 110 190(220) 300(330) *()Stainless steel version MTERILS POS. DESIGNTION MTERIL PV16G-OF MTERIL PV16I-OF 1 Valve Body GJS-400-18-LT / 0.7043 CF8M / 1.4408 2 Bonnet CF8 / 1.4308 CF8 / 1.4308 3 ctuator (Steel) S235JRG2 / 1.0038 S235JRG2 / 1.0038 ctuator (St.steel) ISI 304 / 1.4301 ISI 304 / 1.4301 4 Diaphragm NBR 70 NBR 70 5 Yoke (Steel) C45E / 1.1191 C45E / 1.1191 Yoke (St.Steel) ISI 304 / 1.4301 ISI 304 / 1.4301 6 Valve seal PTFE/GR PTFE/GR 7 Standard packing PTFE/GR PTFE/GR Type DIMENSIONS - CTUTOR ø E (mm) D (mm) DN15-100 D/R WEIGHT Kgs P-205 210 235 5,7 P-280 275 240 8,8 P-340 335 265 14,3 P-435 430 295 24,5 FLOW RTE COEFFICIENTS DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 Kvs 3,8 5,1 9,4 15,4 22,2 40,1 63,4 89,7 136,7 Kvs in m3/h, see data sheet IS PV10.00 E ; For conversion Kvs = Cv(US) x 0,855 CTUTOR STROKE IN mm DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 Stroke 5 5 7 8 10 13 17 20 25 VLSTEM IS PV16OF.70 E 10.06
MX. PERMISSIBLE PRESS.DROP IN bar - Normally closed valve (fluid to open) - CTUTOR (Pressure) MIN. IR PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 P-205 P-280 P-280B P-340 P-340B 25 25 25 12 12 9 6,5 25 16 12 6,5 4 5,7 4 20 18 6,2 5 3 2 For valve sizes DN125 and above please consult. Special spring drops available on request. The pressure drop values must be used within the body rating limits CTUTOR MIN. IR (Pressure) PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 P-205 P-280B P-340B MX. PERMISSIBLE PRESS.DROP IN bar - Normally closed valve (fluid to close) - VLSTEM 25 25 25 25 25 15 Important: not recommended for water and other liquids if fluid direction is over the plug (fluid to close). The pressure drop values are referred to closed valves. 21 14 7 25 19 12 CTUTOR MIN. IR (Pressure) PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 P-205 P-280 P-280B P-340B MX. PERMISSIBLE PRESS.DROP IN bar - Normally open valve (fluid to open) - Direct action actuator (air signal to close) 25 25 25 25 17 14,5 25 24 13 7,5 4 25 16 10 For valve sizes DN125 and above please consult. The actuator pressure drops given with closed valve, are obtained with the following air pressures supply: ctuator signal 0,2 to 1 bar :air supply Special spring drops available on request. The pressure drop values must be used within the body rating limits. For electric actuator selection please consult catalogue IS EL.20.00 E or our technical department. IS PV16OF.70 E 10.06
TROL PNEUMTIC CONTROL VLVES PPV25I ON-OFF (Complete stainless steel) (DN ½ 1 ) (V25I globe valves series with linear piston actuators PP series) DESCRIPTION The PPV25I on-off valves are single seated, two-way body constructed with in-line straight connections. The PPI pneumatic actuator is of the piston type. Their wide application ranges allows the use of this valve with the most common process fluids such as water, superheated water, steam, air, gas and other fluids. MIN FETURES Single seated, two ways, direct or reverse action valve. Soft sealing as standard. ctuator housing 360º rotation (clockwise). OPTIONS: ir filter regulator VLVE LIMITING Normally open and double effect CONDITIONS: Body design conditions: PN25 version. 25 bar at 10/50ºC Limit switch 21 bar at 200ºC Pilot solenoid valve 19,8 bar at 250ºC USE: Saturated and superheated steam. 18,5 bar at 300ºC Hot and superheated water. Min.working temperature: -10ºC ir, gases and other noncorrosive MX. IR SUPPLY fluids. PRESSURE: 8 bar VILBLE MBIENT MODELS: PPV25I - Stainless steel TEMPERTURE: -20ºC...+70ºC BONNET : From -5ºC to +220ºC (standard) VLVE : DN 1/2" to 1" STEM SELING: PTFE/GR V-Rings - up to 220ºC CONNECTIONS: Threaded ISO or NSI (Standard bonnet) CTUTORS: PPI-63 ( Stainless steel ) PLUG TYPES: On-Off (PT) CTUTOR CONN: G1/8" PORT: Full port as standard CONTROL SIGNL: 5-8 bar HOW TO SELECT: Never size the valve according to the pipe diameter in which it has to be fitted but according to the required actual flow of steam or water.refer to valve calculation data sheet or consult the factory. CE MRKING (PED - European Directive 97/23/EC) PN 25 Category DN 1/2" to 1" SEP - art. 3, paragraph3 VLSTEM IS PPV25I.50 E 01.09
MX. PERMISSIBLE PRESS.DROP IN bar - Normally closed valve (fluid to open) - CTUTOR DN 1/2" DN 3/4" DN 1" Kvs 5,2 Kvs 7,3 Kvs 11,7 PPI-63 21 18 8 PPI-90 25 25 24 Kvs in m3/h, see data sheet IS PV10.00 E ; For conversion Kvs = Cv(US) x 0,855 DIMENSIONS ( mm ) DN B C Ø D WEIGHT Kgs 1/2" 100 37,5 250 75 3,9 3/4" 100 37,5 250 75 3,9 1" 100 37,5 250 75 4,9 MTERILS POS. DESIGNTION MTERIL 1 Valve Body CF8M / 1.4408 2 Bonnet CF8M / 1.4408 3 ctuator Flange CF8 / 1.4308 4 ctuator Cover CF8 / 1.4308 5 Piston luminium 6 Indication Stem Plastic 7 Gland Nut ISI 316 / 1.4401 8 * Packing PTFE / GR 9 * Valve Plug 1.4401 / PTFE-GR * vailable spare parts VLSTEM IS PPV25I.50 E 01.09
ORDERING CODES PPV25I VLVE CODES Group Designation Pneumatic on-off valve Valve Model Two way straight design,stainless steel construction PPV.25I.X. PPV.25I Soft (PTFE/GR) PT Type Valve Plug 1 Pipe Connection Threaded BSP ISO 7/1 Rp Threaded NPT NSI B1.20.1 C Size DN 1/2" DN 3/4" DN 1" Fluid Direction Normally closed valve,fluid enter above the seat Normally closed valve,fluid enter below the seat ctuator Extras (3) 15 20 25 B (1) E CTUTOR CODES ( pneumatic ) Group Designation Piston linear actuator ctuator Size Piston pneumatic actuator PPI 63 Piston pneumatic actuator PPI 90 PI. PI..63 To be introduced on ".X.", if supplied in combination with the valve. ctuator Type Direct action (air to close) Reverse action (air to open) ctuator Constrution Stainless steel.d.r (1)- Indicate actuator type. (2)- Omitted if the standard actuator is selected. (2) (3)- To be used only when a non-standard combination valve is supplied VLSTEM IS PPV25I.50 E 01.09
TROL PNEUMTIC CONTROL VLVES PPV16 ON-OFF (V16 globe valves series with linear piston actuators PPI series) DESCRIPTION The PPV16 on-off valves are single seated, two-way body constructed with in-line straight connections. The PPI pneumatic actuators are of the piston type. Their wide application ranges allows the use of this valve with the most common process fluids such as water, superheated water, steam, air, gas and other fluids. MIN FETURES Single seated, two ways, direct or reverse action valve. Soft sealing as standard. ctuator housing 360º rotation (clockwise). OPTIONS: USE: VILBLE MODELS: ir filter regulator Stainless steel construction. Normally open and double effect version. Limit switch Pilot solenoid valve Saturated and superheated steam. Hot and superheated water. ir, gases and other noncorrosive fluids. PPV16G - Nodular iron PPV16I - Stainless steel 12,8 bar 300ºC VLVE : DN15 to DN50 MX. IR SUPPLY CONNECTIONS: Flanged EN1092-2 PN16 (PPV16G) PRESSURE: 8 bar Flanged EN1092-1 PN16 (PPV16I) MBIENT CTUTORS: PPI-63, PPI-90 (Stainless steel) TEMPERTURE: -20ºC...+70ºC BONNET : From -5ºC to +220ºC (standard) CTUTOR CONN: G1/8" - G1/4" STEM SELING: PTFE/GR V-Rings - up to 220ºC (Standard bonnet) PLUG TYPES: On-Off (PT) PORT: Full port FLOW RTE COEFFICIENTS DN15 DN20 DN25 DN32 DN40 DN50 Kvs 5,2 7,3 11,7 18 27 43 VLVE BODY LIMITING CONDITIONS PPV16G Press. Temp. 16 bar -10 / 120ºC 15,5 bar 150ºC 14,7 bar 200ºC 13,9 bar 250ºC PPV16I Press. Temp. 16 bar -10 / 100ºC 14,5 bar 150ºC 13,4 bar 200ºC 12,7 bar 250ºC 11,8 bar 300ºC CE MRKING (PED - European Directive 97/23/EC) PN 16 Category DN15 to DN50 SEP - art. 3, paragraph3 VLSTEM IS PPV16.50 E 01.09
MX. PERMISSIBLE PRESS.DROP IN bar Normally closed valve (fluid to open) CT. Type IR PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 PPI-63 5-8 bar 18 18 8 4 3 - PPI-90 5-8 bar - - 24 18 13 9 Note: Waterhammer free design. MX. PERMISSIBLE PRESS.DROP IN bar Normally closed valve (fluid to close) CT. Type IR PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 PPI-63 5-8 bar 16 16 16 - - - PPI-63 6-8 bar 16 16 16 16 - - PPI-63 7-8 bar 16 16 16 16 16 10 PPI-90 5-8 bar - - - 16 - - PPI-90 6-8 bar - - - 16 16 - PPI-90 7-8 bar - - - 16 16 16 Note: not recommended when controlling liquids at high speed doing to waterhammer occurrence. DIMENSIONS (mm) C Ø D C Ø D DN B ctuator ctuator PPI-63 PPI-90 WHT. Kgs w/ppi63 WHT. Kgs w/ppi90 15 130 48 250 75 300 110 3,7 5,2 20 150 53 250 75 300 110 4,5 6 25 160 58 255 75 305 110 5,5 7 32 180 70 260 75 310 110 7 8,5 40 200 75 265 75 315 110 9,7 11,2 50 230 83 270 75 320 110 11,7 13,2 MTERILS POS. DESIGNTION MTERIL PPV16G MTERIL PPV16I 1 Valve Body GJS-400-18-LT / 0.7043 CF8M / 1.4408 2 Bonnet CF8 / 1.4308 CF8 / 1.4308 3 ctuator Flange CF8 / 1.4308 CF8 / 1.4308 4 ctuator Cover CF8 / 1.4308 CF8 / 1.4308 5 Piston luminium luminium 6 Indication Stem Plastic Plastic 7 Gland Nut ISI 316 / 1.4401 ISI 316 / 1.4401 8 * Packing PTFE / GR PTFE / GR 9 * Valve Plug 1.4401 / PTFE-GR 1.4401 / PTFE-GR * vailable spare parts VLSTEM IS PPV16.50 E 01.09
ORDERING CODES PPV16 VLVE CODES Group Designation Pneumatic on-off valve Valve Model Two way straight design,nodular iron construction Two way straight design,stainless steel construction Valve Plug Soft (PTFE/GR) PT Type PPV PPV.16G.16I 1.X. Flanged EN1092 PN16 Pipe Connection L Size DN 15 DN 20 Fluid Direction Normally closed valve,fluid enter above the seat Normally closed valve,fluid enter below the seat ctuator Extras (3) 15 20 B (1) E CTUTOR CODES ( pneumatic ) Group Designation Piston linear actuator ctuator Size Piston pneumatic actuator PPI 63 Piston pneumatic actuator PPI 90 PI. PI..63.90 To be introduced on ".X.", if supplied in combination with the valve. ctuator Type Direct action (air to close) Reverse action (air to open) ctuator Constrution Stainless steel.d.r (1)- Indicate actuator type. (2)- Omitted if the standard actuator is selected. (2) (3)- To be used only when a non-standard combination valve is supplied VLSTEM IS PPV16.50 E 01.09