Type No. Catalog No. Job. Name APPLICATIONS Applications include large and small retail facilities, lobbies, conference rooms, auditoriums and other commercial and light industrial spaces. CONSTRUCTION A cylindrical ballast housing features a tool-less wiring access door for simple installation and maintenance. Single baffle is standard. Dual or Tri-Baffle option may be specified. Ballast housing has an Ultra-Clad polyester powder coating, electrostatically applied and oven cured. Standard colors and five new metallic finishes available. Custom RAL colors may be specified. Custom designed multi-color luminaire may be specified. OPTICS The prismatic refractor of UV stabilized acrylic adds an uplight component to give fill light on ceiling surfaces, improving the quality of the lighting environment. The ELA Low Wattage HID series is available as either an open or enclosed unit in two sizes in all wattages. Enclosed units feature a refractive lower lens which allows relamping. 19 enclosed units have a conical lower lens. 22 enclosed units may be specified with either a conical or dropped lens. ELECTRICAL High frequency electronic ballast operation provides constant wattage regulation and features THD in the range of <10% to <20% and is suitable for operation in an ambient temperature range of -30 C (-22 F) to 40 C (104 F). The digitally controlled ignition inherent in the Element s microprocessorcontrolled electronic ballast eliminates lamp electrode wear and wall blackening. Unit may be specified with a standard dimming range to 50% power. The BL option provides Bi-Level (Hi / Low) dimming to 50% power. The AD option provides Analog (full range) Dimming to 50% power MOUNTING Standard pendant mounting features a cast aluminum nut and hub to provide quick, positive mounting to 3/4 NPT or NPSM conduit. WARRANTY/LISTINGS Standard 3 Year Limited Warranty. UL/cUL Listed luminaire, UL 1598, 40 C (104 F) rated, suitable for damp locations. The quality systems of this facility have been Registered by UL to the ISO 9000 Series Standards. 19.2 (48.7cm) 14.1 (35.8cm) typical for 19 optics 2.6 (6.5cm) 29.0 (73.6cm) 22.5 (57.2cm) 1.5 (3.8cm) typical for 22 & 25 19.2 (48.7cm) 32.7 (83.1cm) 30.7 (77.9cm) 32.7 (83.1cm) 33.5 (85.1cm) 22.5 (57.2cm) 22.5 (57.2cm) See Page 2 for Ordering Information
Element Acrylic High Bay 22 enclosed, conical lens, standard single baffle Notes 1) Element Acrylic High Bay Pulse Start low wattage HID luminaires require the use of O rated lamps with the exclusionary lamp base (EDX17 or EDP) only. Do not use any other base lamp. Standard Element Pulse Start Metal Halide units use E17 lamps which are suitable for 50% dimming options. 2) Optional BL and AD dimming is available with E1 (Metrolight SuperHID) ballast only. 3) In the ies file, elpc denotes element, pulse Start, coated lamp. Wattage abbreviations: 5 = 50W, 7 = 70W, 10 = 100W, 15 = 150W. Optics abbreviations: 19o = 19 open, 19c = 19 with conical lens, 22o = 22 open, 22c = 22 with conical lens, 22d = 22 with dropped lens. Files reflect the use of phosphor coated lamps. Contact factory for data using clear lamps. 4) Calculated in accordance with NEMA Standard LE-5B using standard Pulse Start Metal Halide lamps. Slightly higher LER values may be achieved with the use of e-lamps. See note 1 above. Series (1) Pulse Start Metal Halide r ELP-50 r ELP-70 r ELP-100 r ELP-150 Compliant Pulse Start Metal Halide Energy Independence Security Act Optics r A19O 19 Acrylic High Bay, Open r C19E 19 Acrylic High Bay, Enclosed, Conical lens r A22O 22 Acrylic High Bay, Open r C22E 22 Acrylic High Bay, Enclosed, Conical lens r D22E 22 Acrylic High Bay, Enclosed, Dropped lens Distribution Guide and Ballast Data Voltage / E ballast / Dimming Voltage: r 120 r 208 r 240 r 277 Electronic ballast type: (2) r E Electronic ballast (standard) Alternately, a specific manufacturer s product may be selected. Consult factory. Dimming: (2) r E1 = Metrolight SuperHID r E3 = Ace r E4 = Advance e-vision Ballast Ordering Examples: Standard 120v 208v 240v 277v ballast: 120E 208E 240E 277E E1, E3 or E4 : ballast manufacturer 120v 208v 240v 277v Metrolight SuperHID 120E1 208E1 240E1 277E1 120E3 208E3 240E3 277E3 120E4 208E4 240E4 277E4 Optional dimming ballast s range is down to 50% power. Leave blank to specify ballast. r BL = Bi-Level (Hi / Low) dimming to 50% power r AD = Analog (full range 0-50) dimming to 50% power Available with E1 (Metrolight SuperHID) ballast only. Wattage Optics ies (3) ANSI Line Current Line LER (4) File Name Code 120 / 208 / 240 / 277 Watts PSMH 50 19 open elpc519o.ies M110/M148 0.67 / 0.32 / 0.26 / 0.22 60 44 19 conical elpc519c.ies 49 22 open elpc522o.ies 47 22 conical elpc522c.ies 42 22 dropped elpc522d.ies 48 PSMH 70 19 open elpc719o.ies M98/M143 0.70 / 0.46 / 0.38 / 0.31 80 54 19 conical elpc719c.ies 61 22 open elpc722o.ies 59 22 conical elpc722c.ies 52 22 dropped elpc722d.ies 60 PSMH 100 19 open elpc1019o.ies M90/M140 0.94 / 0.64 / 0.53 / 0.42 113 62 19 conical elpc1019c.ies 70 22 open elpc1022o.ies 67 22 conical elpc1022c.ies 59 22 dropped elpc1022d.ies 68 PSMH 150 19 open elpc1519o.ies M102/M142 1.41 / 0.99 / 0.85 / 0.69 167 66 19 conical elpc1519c.ies 74 22 open elpc1522o.ies 71 22 conical elpc1522c.ies 62 22 dropped elpc1522d.ies 72 Ace Advance E-Vision
Standard colors Decorator colors r WHT Custom Multi-color Luminaire r PRL Smooth White (Default ballast finish if color is not specified.) Pearl Defined by Custom Submittal Drawing available on website Consult factory for assistance. r MC(XXX) = Custom Multi-Color r TWHT Simple two-color Element Custom Multi-Color Luminaire Example: White r TBK r PWT r TSA r CRL Black Decorator colors Charcoal and Pewter are shown. Pewter Satin Aluminum Charcoal r TGR r BGE r TDB r TER Beige Gray Dark Bronze Terra First, specify overall custom ballast color. Lens trim color on enclosed units is typically the same as ballast color, but may be specified to match baffle if desired. r TGN Green Second, specify contrasting baffle color. RAL color may also be specified. r RAL(X) X = Custom RAL color number Consult factory Single Baffle is standard. The baffles in a Dual Baffle or Tri-Baffle option are typically specified as the same contrasting color on a Custom Multi-Color unit. However, any combination of colors may be specified as defined by the Custom Submittal Drawing.
Options (Factory Installed) Decorative Baffle Options r BD Dual Baffle r BT Tri-Baffle Note: Single Baffle is standard. Decorative Cable Mounting For Non-Dimming units r CC(X) Cable Mount Luminaire with single Coil r CS(X) Cable Mount Luminaire with single Straight (X) = length in feet: 3, 6 or 8 Note: LQ1 is not available with CC or CS option. For Dimming units When Element luminaires with dimming capabilities are specified with a suspended cable mount option, the use of both the straight and coil cords is required. A central straight cable carries the low voltage dimming leads to the ballast and a coil cord supplies ballast and lamp power. Upper mounting plate detail at right shows the luminaire suspension cables and the straight and coil cord combination. Decorative Cable Mount Lower Lens Lens size dependent on optics. r L1C Solid suspended Clear glass lens r L1D Solid suspended Diffuse glass lens Optics Nominal Diameter Lens Diameter Hole Diameter 19 and below 24.0 (60.96cm) 9.5 (24.13cm) 22 and above 32.0 (81.28cm) 13.5 (34.29cm) Solid Glass Lens: Note: The suspended lens option is shown with Metal over Glass optics (ELMG). lens options are available for ELA low wattage HID units with open optics only. detail: lens suspend fitting and cable connection at baffle detail: lens suspend fitting and cable connection at lens Lens with center opening: r L2C Clear glass lens with center opening r L2D Diffuse glass lens with center opening Silkscreened Clear Lens: r L1S = r L2S = Silkscreened clear glass lens with center opening Silkscreened clear glass lens Consult factory. May be specified by ink color, dot pattern, or by client determined logo art or design.
Decorative Remote Ballast Mounting Note: Dimming or Non-Dimming units with LQ / LQ1 option require both a central straight cord as well as a coil cord. dimming or without LQ / LQ1 r RC(X) Remote Ballast, Cable Mount Luminaire with single Coil (X) = length in feet: 3, 6 or 8 (max) dimming or without LQ / LQ1 r RS(X) Remote Ballast, Cable Mount Luminaire with single Straight (X) = length in feet: 3, 6 or 8 (max) max 8 dimming or with CSR, LQ or LQ1 r RP(X) Remote Ballast, Pendant Mount Luminaire mounted to 3/4 NPT rigid conduit (X) = Pendant length in feet: 3, 6 or 8 Auxiliary / Emergency Lighting r CSR = Hot Quartz Restrike using Current Sensing Relay (Extinguishes auxiliary lamp when main arc strikes.) r LQ = Hot / Cold Quartz Restrike (Litematic Operation) r LQ1 = Separately Wired (120V) Hot / Cold Quartz Restrike (Externally controlled emergency lighting from a separate power source. To ensure integrity of the emergency lighting system, LQ1 leads should be hardwired. Suitability of specifying emergency lighting (LQ1) with (5-wire) cord and plug is the determination of the user.) LQ1 is not available with single cord CC or CS option. LiteMatic Operation Normal Start: Main and Quartz lamps both energized. Main Lamp Reaches Approximately 40% of Rated Output: Quartz lamp automatically extinguishes (combined lamp currents never exceed that of main lamp at 100% output). When Arc Extinguished: Auxiliary quartz lamp automatically energized when power is restored. Main Lamp Reaches 40% of Rated Output: Quartz lamp automatically extinguishes Ballast Fusing r F1 = Single Fuse, 120 / 277V r F2 = Double Fuse, 208 / 240V Alternate Mounting r HCP-(X)C-L(Y)20P = Hook, and Plug, 3-Wire (X) = length in feet: 3, 6 or 10 r HCP-(X)C-L2320P = Hook, and Plug, 5-Wire (X) = length in feet: 3, 6 or 10 r H4-HCP-L(Y)20P = Pendant Power Hook, 3-Wire (300V) with HCP r H4-HCP-L2320P = Pendant Power Hook, 5-Wire (600V) with HCP r LCP-(X)C-L(Y)20P = Loop, and Plug, 3-Wire (X) = length in feet: 3, 6 or 10 r LCP-(X)C-L2320P = Loop, and Plug, 5-Wire (X) = length in feet: 3, 6 or 10 r H5-LCP-L(Y)20P = Power Hook, 3-Wire (300V) with LCP r H5-LCP-L2320P = Power Hook, 5-Wire (600V) with LCP Unit is pre-wired with 3-conductor rubber jacketed cable and heavy duty (16/3) NEMA twist-lock plug, along with die-cast hook with locking screw. 20A standard. When specified with LQ1, unit is pre-wired with 5-conductor rubber jacketed cable and heavy duty (16/5) NEMA twist-lock plug (L2320P), along with die-cast hook with locking screw. 20A standard. Pendant Mounted Power Hook with NEMA receptacle. Unit is pre-wired with Hook, and Plug. When specified with LQ1, Pendant Mounted Power Hook has an L2320R NEMA receptacle. Unit is pre-wired with 3-conductor rubber jacketed cable and heavy duty (16/3) NEMA twist-lock plug, with diecast loop. 20A standard. When specified with LQ1, unit is pre-wired with 5-conductor rubber jacketed cable and heavy duty (16/5) NEMA twist-lock plug (L2320P), with die-cast loop. 20A standard. Power Hook with thru-wire provision contains a NEMA receptacle. Unit is prewired with Loop, and Plug. When specified with LQ1, 5-Wire version is required. Ballast Safety Cable Not available on units with suspended cable option or remote ballast option. r SC3 = 3 Safety Cable r SC6 = 6 Safety Cable r SC10 = 10 Safety Cable
Accessories (Field Installed - Shipped Separately) Ballast Fusing r F1-Kit = Single Fuse, 120 / 277V r F2-Kit = Double Fuse, 208 / 240V Alternate Mounting r HCP-(X)C-L(Y)20P = Hook, and Plug, 3-Wire (X) = length in feet: 3, 6 or 10 r HCP-(X)C-L2320P = Hook, and Plug, 5-Wire (X) = length in feet: 3, 6 or 10 r H4 = Pendant Power Hook, 3-Wire r H4-5W = Pendant Power Hook, 5-Wire r LCP-(X)C-L(Y)20P = Loop, and Plug, 3-Wire (X) = length in feet: 3, 6 or 10 r LCP-(X)C-L2320P = Loop, and Plug, 5-Wire (X) = length in feet: 3, 6 or 10 r H5 = Power Hook with thru-wire provision, 3-Wire r H5-5W = Power Hook with thru-wire provision, 5-Wire 3-conductor rubber jacketed cable and heavy duty (16/3) NEMA twist-lock plug as specified, with die-cast hook with locking screw. 20A standard. When specified for unit equipped with LQ1, 5-conductor rubber jacketed cable is required, which is wired to a heavy duty (16/5) NEMA twist-lock plug (L2320P), with die-cast hook with locking screw. 20A standard. Pendant Mounted Power Hook with NEMA receptacle as specified. Used with corresponding Hook, and Plug. When specified for unit equipped with LQ1, 5-wire version is required. 3-conductor rubber jacketed cable and heavy duty (16/3) NEMA twist-lock plug as specified, with die-cast loop. 20A standard. When specified for unit equipped with LQ1, 5-conductor rubber jacketed cable is required, which is wired to a heavy duty (16/5) NEMA twist-lock plug (L2320P), with die-cast loop. 20A standard. Power Hook with thru-wire provision contains a NEMA receptacle. Used with corresponding Loop, and Plug. When specified for unit equipped with LQ1, 5-Wire version is required. Mounting Extras r HM Hook Male r LM Loop Male r JA75 Joint Aligner 50 lb. maximum allowed. r SH75 Swivel Hanger 50 lb. maximum allowed if hung from junction box. Notes Philips Lighting Company 200 Franklin Square Drive Somerset, NJ 08873 Phone: 855-486-2216 Philips Lighting Company 281 Hillmount Road Markham ON, Canada L6C 2S3 Phone: 800-668-9008