External Gear Pumps Series N

External Gear Pumps Series N RE 1 91/2.7 AZPN-... Fixed pumps V =...36 cm 3 /rev Overview of contents Contents Page General 2 Product overview 3 Ordering code single pumps 4 Ordering code multiple pumps 5 Drive shaft 6 Front cover 6 Line ports 7 Gear pumps with integral valves 8 Design calculations for pumps 8 Performance charts 9 Noise charts 11 Specifications 12 Drive arrangements 13 Multiple gear pumps 15 Unit dimensions 16 Fittings 21 Service parts 22 Notes for commissioning 23 Ordering-No. 24 Features Nominal pressure 2 bar Slide bearings for heavy duty applications Drive shafts to ISO or SAE Combination of several pumps possible Line ports: connection flanges Consistent high quality thru mass production Numerous configuration variants available

2/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 General Rexroth external gear pumps are available as standard gear pumps in the 4 series of B, F, N and G and as SILENCE gear pumps in the series of S, T and U, in which the displacements are graded by different gear widths. Further configuration variants are given by different flanges, shafts, valve arrangements and multiple pump combinations. Construction The external gear pump consists essentially of a pair of gears supported in bearing bushings or bearing, dependent on the series, and the case with a front and rear cover. The drive shaft protrudes from the front cover where it is sealed by the shaft seal ring. The bearing forces are absorbed by special bearing bushings with sufficient elasticity to produce surface contact instead of line contact. They also ensure excellent resistance to galling especially at low speed. The gears have 12 teeth. This keeps both flow pulsation and noise emission to a minimum. The internal sealing is achieved by forces which are proportional to delivery pressure. This ensures optimum efficiency. The bearings provide the seal at the ends of the gaps between the teeth which carry the pressurized oil. The sealing zone between the gear teeth and the bearings is controlled by the admission of operating pressure to the rear of the bearing bushings. Special seals form the boundary of the zone. The radial clearance at the tips of the gear teeth is sealed by internal forces pushing them against the case. Gear pump axial compensation Axial seal External pressure zone Internal pressure zone Radial seal Cover Flange Sealing zone Compensation forces 1 2 3 4 5 6 7 8 9 1 11 12 13 14 1 Retaining ring 2 Shaft seal ring 3 Front cover 4 Slide bearing 5 Centering pin 6 Gear 7 Gear (frictional) 8 Case seal 9 Pump case 1 Bearing 11 Axial zone seal 12 Support 13 End cover 14 Fixing screws

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 3/24 Overview of Series N standard types Version 16 Version 18 Version 17 19 The AZ configurator at www.boschrexroth.com/azconfigurator The AZ configurator assists you to configure your individual external gear unit easily and user-friendly. You only need to specify your requirements: From the displacement, direction of rotation, drive shaft, connection flange right up to the required rear cover. You immediately receive a project drawing (PDF format) if a configuration already exists. You receive the price of the configured external gear unit upon request. The AZ configurator assists you to configure your individual external gear unit easily and userfriendly all data needed for project planning are acquired thru menu guidance. Selection is made either on an ordering code or your technical requirements. This means that you can search for external gear units that have already been configured, or you specify the configuration variant of the external gear unit based upon the operating parameters you require. If the external gear unit you selected has been released you will receive the part number, ordering code and a detailed installation drawing. If your special configuration is not available please send your specification to Rexroth. One of our employees will then contact you.

4/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Ordering code External gear units, single pumps, standard AZ P N x x R C B M B 189 S xxxx Function P = Pump Series 1 = Case width 92 mm 2 = Case width 11 mm Version 1 = Phosphatized, pinned 2 = Chromatized, pinned Size N =. cm 3 /rev 22 = 22.5 cm 3 /rev 25 = 25. cm 3 /rev 28 = 28. cm 3 /rev 32 = 32. cm 3 /rev 36 = 36. cm 3 /rev Direction of rotation R = Clockwise L = Counterclockwise *) Some of the special designs shown on pages 16 21 are not covered in the illustration of the ordering code. Special design *) Valve adjustment xx = PRV bar xxx 11 = FCV 11 l/min 189 = PRV + FCV 18 bar, 9 l/min Rear cover B = Standard D = PRV residual flow internal E = FCV residual flow external S = FCV residual flow internal V = PRV + FCV Seals M = NBR K = NBR, SSR in FPM Drive shafts Front cover Line ports Suitable front cover C Tapered key shaft 1 : 5 B B Square flange Centering Ø 1 mm 7 Square flange SAE Thread, metric N Dihedral claw M C D Splined shaft SAE J 744 22-4 13T C M SAE J 744 11-2 B 2-bolt flange Ø 11.6 mm 2-bolt mounting Centering Ø 52 mm with seal ring Rectangular flange P Splined shaft SAE J 744 19-4 11T C Not all variants can be selected by using ordering code! Please select the required pump by using the selection tables (standard types) or after consultation with Bosch Rexroth! Special options are possible upon request.

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 5/24 Ordering code External gear units, multiple pumps, standard AZ P NNFF x x 32/22/16/5 R C B K B Function P = Pump Series B = 1... 7.1 cm 3 /rev S = 4...28. cm 3 /rev F = 4...28. cm 3 /rev N =...36. cm 3 /rev G = 22.5...56. cm 3 /rev Series, relates to pump section 1 1 = Case width 92 mm 2 = Case width 11 mm Version, relates to pump section 1 1 = Phosphatized, pinned 2 = Chromatized, pinned Size corresponding to each series Direction of rotation R = Clockwise L = Counterclockwise Rear cover relates to last pump section B = Standard Seals M = NBR P = FPM K = NBR, SSR in FPM Shaft seal relate to pump section 1 Drive shafts relates to pump part 1 Series B: H Suitable front cover Tapered key shaft 1 : 8 O O Front cover relates to pump part 1 Square flange Centering Ø 25.38 mm 2 Line ports every pump parts Thread, metric DIN 3852 T1 Series F, S: C H R Series N, T: C D Tapered key shaft 1 : 5 B B Tapered key shaft 1 : 8 O O Splined shaft SAE J 744 16-4 9T R R Tapered key shaft 1 : 5 B B Splined shaft SAE J 744 22-4 13T C C N Dihedral claw M M Series G, U: C D H Tapered key shaft 1 : 5 B B Splined shaft SAE J 744 22-4 13T C C Tapered key shaft 1 : 8 O O Square flange Centering Ø 8 mm Rectangular flange Square flange Centering Ø 36.47 mm SAE J 744 82-2 A Centering Ø 82.55 mm 2-bolt mounting Square flange Centering Ø 1 mm 7 SAE J 744 11-2 B Centering Ø 11.6 mm 2-bolt mounting Centering Ø 52 mm with seal ring Square flange Centering Ø 15 mm 7 SAE J 744 11-2 B Centering Ø 11.6 mm 2-bolt mounting Square flange Centering Ø.78 mm Square flange SAE Thread, metric Rectangular flange Square flange SAE Thread, metric Rectangular flange Not all variants can be selected by using ordering code! Please select the required pump by using the selection tables (standard types) or after consultation with Bosch Rexroth! Special options are possible upon request.

6/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Drive shafts C 45.5 ±.6 2 9 ±.2 5 42'38" ±1' DIN 128-A14-FSt 4x6.5 DIN 6888 Ø22 N Ø21.8 ±.84.83 8.25 8.8 ±.3 2.7 ±.5 1:5 M14x1.5-m-6 Pump without shaft seal D 31 9.5 ±.1 P 41 ±.4 9.5 ±.1 Ø21.86.127 Ø22..72 Ø21.86.127 Ø22.1 Min..1 usable shaft length ANSI B 92.1 13T 16/32 DP pressure angle Min. 23 usable shaft length ANSI B 92.1 11T 16/32 DP pressure angle Front cover Ø1.54 B 18.75 ±1 9 ±.2 Ø22 ±.5 132 ±.2 11 ±.135 44.2 ±.1 R 1 ±.5 55 ±1.5 153 ±1.5 C Ø11.6.5 Ø51 9.5 ±.1 max. 3 13.2 ±1 Ø24 9.5 ±.1 42 ±2 SAE - B "X" R ±1.1 14.3 ±.27 12.5 ±1.5 88.4 ±.2 11 ±1.5 "X" 146 ±.15 174 ±1.3

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 7/24 Front cover (continued) M Ø52.76. Ø47.8.2 7.2 ±.2 11.5 ±.2 Ø ±.18 66 ±.2 min. 1.6 66 ±.2 33 ±.1 14 ±.1 25 ±1.5 2 ±.2 3.2 ±.2 Pump without shaft seal 2xM1 1.9 Line ports 7 Square flange SAE, thread, metric F C D E Ordering Size Pressure side Suction side C D E F C D E F 7 cm 3 18 47.6 M 1 22.2 18 47.6 M 1 22.2 22.5...36 cm 3 depth 14 26.2 26 52.4 depth 14 26.2 45 45 Rectangular flange C D E Ordering Size Pressure side Suction side C D E C D E...36 cm 3 18 55 M 8 depth 13 26 55 M 8 depth 13

8/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Gear pumps with integral valves In order to reduce external pipework it is possible to incorporate a flow-control valve or pressure-relief valve in the cover of the gear pump. A typical application of this is in the supply of hydraulic oil in power steering systems. The pump delivers a constant flow irrespective of the speed at which it is driven. The excess flow is either returned internally to the suction port or distributed externally to other items of equipment. upon request 3 const. 3 const. Q const. p1 p 1 3-way flow-control valve. Excess flow returned to suction line Q const. = 2... l/min 3-way flow-control valve. Excess flow distributed externally; loadable Q const. = 2... l/min 3-way flow-control valve with pressure-relief valve. Excess flow returned to suction line Q const. = 2... l/min p 1 = 1...18 bar Pressure-relief valve. Discharge returned to suction line p 1 = 5...2 bar Ordering code S xxx17 E xxx12 V 111 D 18xx Design calculations for pumps The design calculations for pumps are based on the following parameters: V [cm 3 /rev] Q [l/min] p [bar] M [Nm] n [rev/min] P [kw] Displacement Delivery Pressure Drive torque Drive speed Drive power It is also necessary to allow for different efficiencies such as: η v η hm η t Volumetric efficiency Hydraulic-mechanical efficiency Overall efficiency The following formulas describe the various relationships. They include correction factors for adapting the parameters to the usual units encountered in practice. Caution: Diagrams providing approximate selection data will be found on subsequent pages. P M n Q V [%] n η v Q M η hm p P η t p Q p Q = V n η v 1 5 M η hm p = 1.59 V p Q P = 6 η t Q V = 1 5 n η v M η hm V = 159 p 6 P η Q = t p V [cm 3 /rev] Q [l/min] p [bar] Caution: η [%] e.g. 95 [%] n [rev/min] P [kw] M [Nm] Q n = 1 5 V η v 1.59 V p M = η hm 6 P η p = t Q

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 9/24 Performance charts 9 ν = 35 mm 2 /s, ϑ = C 8 7 p = bar p 2 = max. intermittent V = 36 cm 3 / U rev 32 28 25 22.5 Q [l/min] 1 1 n [rpm] Q = f ( n,v ) incl. η v P = f (n, p) incl. η t M = f (n, p) incl. η hm V = cm 3 U / rev V = 22.5 cm 3 / U rev 15 p = 2 bar 15 p = 2 bar 9 9 75 75 P [kw] 1 1 p = 2 bar 45 15 M [Nm] P [kw] 1 1 p = 2 bar 1 45 15 M [Nm] 1 1 1 1 1 1 n [rpm] 1 n [rpm]

1/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Performance charts (continued) V = 25 cm 3 / U rev V = 28 cm 3 / U rev p = 2 bar 1 p = 2 bar 1 P [kw] 1 1 p = 2 bar 1 8 M [Nm] P [kw] 1 1 p = 2 bar 1 8 M [Nm] 1 1 1 1 1 1 1 n [rpm] 1 n [rpm] V = 32 cm 3 / U rev V = 36 cm 3 / U rev p = bar 1 p = 18 bar 1 1 1 8 1 1 8 1 1 P [kw] p = bar 1 M [Nm] P [kw] p = 18 bar 1 M [Nm] 1 1 1 1 1 n [rpm] 1 n [rpm]

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 11/24 Noise charts Noise level dependent on rotational speed, pressure range between 1 bar and pressure value p 2 (see page 12/13 Specifications table). Oil data: ν = 32 mm 2 /s, ϑ = C. Sound pressure level calculated from noise measurements made in the sound absorbent measuring room compliant with DIN 45635, Part 26. Spacing between measuring sensor pump: 1 m. These are typical characteristic values for the respective model. They describe the airborne sound emitted solely by the pump. Environmental influences (installation site, piping, further system components) are not taken into consideration. Each value applies for a single pump. V = cm 3 / U rev 75 7 65 55 V = 22,5 cm 3 / U rev 75 7 65 55 LpA [db(a)] 45 35 LpA [db(a)] 45 35 1 n [rpm] 1 n [rpm] V = 25 cm 3 / U rev 75 V = 28 cm 3 / U rev 75 7 7 65 65 55 55 LpA [db(a)] 45 35 LpA [db(a)] 45 35 1 n [rpm] 1 n [rpm] V = 32 cm 3 / U rev 75 V = 36 cm 3 / U rev 75 7 7 65 65 55 55 LpA [db(a)] 45 35 LpA [db(a)] 45 35 1 n [t/min] 1 n [rpm]

12/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Specifications General Construction Mounting Line ports Direction of rotation (looking on shaft) Installation position Load on shaft Ambient temperature range External gear pump Flange or through-bolting with spigot Flange Clockwise or counterclockwise, the pump may only be driven in the direction indicated Any Radial and axial forces after consulting C...+8 C with NBR seal C...+11 C with FPM seals Fluids Mineral oil compliant with DIN 51 524, 1 3, however under higher load at least HLP compliant with DIN 51 524 Part 2 recommended. Comply with RE 775 Further operating fluids possible after consultation Viscosity 12...8 mm 2 /s permitted range...1 mm 2 /s recommended range... mm 2 /s range permitted for starting Fluid temperature range C...+8 C C...+11 C with FPM seals Filtration *) At least cleanliness level 21/18/15 compliant with ISO 46 (1999) *) During the application of control systems or devices with critical counter-reaction, such as steering and counterbalance valves, the type of filtration selected must be adapted to the sensitivity of these devices. Safety requirements pertaining to the whole systems are to be observed. In the case of applications with high numbers of load cycles please consulting. Definition of direction of rotation Always look on the drive shaft. Caution: Dimensions drawings always show clockwise-rotation pumps. On counter-clockwise-rotation pumps the positions of the drive shaft and the suction and pressure ports are different. Definitions of pressures bar p 3 p 2 Pump pressure p 1 Time t max. s p 1 max. continuous pressure p 2 max. intermittent pressure p 3 max. peak pressure Clockwise rotation Counter-clockwise rotation AZPN-1x Displacement V cm 3 /rev 22.5 25 28 32 36 Suction pressure p e.7...3 (absolute), with tandem pumps p e (p 2 ) = max..5 p e (p 1 ) Max. continuous pressure p 1 bar 2 2 2 21 18 1 Max. intermittent pressure p 2 2 2 2 2 18 Max. peak pressure p 3 27 27 27 2 2 Min. rotational speed < 1 rpm at bar 12 mm 2 /s 1...18 18... p 2 8 8 8 8 8 8 25 mm 2 /s p 2 Max. rotational speed at p 2 28 28 28

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 13/24 AZPN-2x (only upon request) Displacement V cm 3 /rev 22.5 25 28 32 36 Suction pressure p e.7...3 (absolute), with tandem pumps p e (p 2 ) = max..5 p e (p 1 ) Max. continuous pressure p 1 bar 2 2 2 2 21 18 Max. intermittent pressure p 2 28 28 28 2 2 21 Max. peak pressure p 3 28 2 2 Min. rotational speed < 1 rpm at bar 12 mm 2 /s 1...18 18... p 2 8 8 8 8 8 8 25 mm 2 /s p 2 Max. rotational speed at p 2 28 28 28 Drive arrangements 1. Flexible couplings The coupling must not transfer any radial or axial forces to the pump. The maximum radial runout of shaft spigot is.2 mm. Refer to the fitting instructions provided by the coupling manufacturer for details of the maximum permitted shaft misalignment. 2. Coupling sleeve Used on shafts with DIN or SAE splining. Caution: There must be no radial or axial forces exerted on the pump shaft or coupling sleeve. The coupling sleeve must be free to move axially. The distance between the pump shaft and drive shaft must be 2 +1. Oil-bath or oil-mist lubrications is necessary. 34 2 +1 Ø25 h11 Splined shaft profile Ordering code M max [Nm] SAE-B 13 teeth D SAE-C 11 teeth P n. n.

14/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 3. Drive shaft with tang For the close-coupling of the pumps to electric motor or internal-combustion engine, gear, etc. The pump shaft has a special tang and driver c (not included in supply). There is no shaft sealing. a R1 ±.2.83 1.25 The recommended arrangements and dimensions for the drive end and sealing are as follows. 8.8 ±.2 min. 8 3.2.5 c a Drive shaft Case-hardening steel DIN 17 21 e.g. MnCrS 5 case-hardened 1. deep; HRA 83 ±2 Surface for sealing ring ground without rifling R t 4µm b Ø22..24 Ø52 ±.46 15 b Radial shaft seal ring Rubber-covered seal (see DIN 37, Type AS, or double-lipped ring). Cut 15 chamfer or fit shaft seal ring with protection sleeve. 4. V-belts and gearwheels without outboard bearing When proposing to use V-belt or gear drive, please submit details of the application for our comments (especially dimensions a, d m, d w and angle α). α α dm dw Ø37 M max [Nm] 95 A V [cm 3 /rev] p max [bar] 27 22.5 2 25 2 28 19 32 17 36 1.2 A a 18 a 18

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 15/24 Multiple gear pumps Gear pumps are well-suited to tandem combinations of pumps in which the drive shaft of the first pump is extended to drive a second pump and sometimes a third pump in the same manner. A coupling is fitted between each pair of pumps. In most cases each pump is isolated from its neighbor, i.e. the suction ports are separate from one another. A common suction port is also possible as an option. Caution: Basically, the specifications for the single pumps apply, but with certain restrictions: Max. speed: This is determined by the highest rated pump speed in use. Pressures: These are restricted by the strength of the drive shaft, the through drives and the drivers. Appropriate data is given in the dimensional drawings. Pressure restrictions during standard through drive In the case of series N, the driver for the second pumping stage can carry a load of up to M max. = 95 Nm, i.e. there is a pressure restriction for the second stage and any further stages. Combinations Series pump 1 N N N M max. [Nm] 95 65 M max. F Series pump 2 N F For configuration of multiple pumps we recommend the pump is positioned with the largest displacement on the drive side. Drive shaft Max. transferrable drive torque * [Nm] C 1: 5 N Claw 95 D SAE 13t 3 P SAE 11t 18 * These values only apply when the conditions described above are complied with. Bosch Rexroth is to be consulted if the stated values are exceeded. If the first stage is driven through a tang (driver) or outboard bearing type 1, pressure restrictions apply as indicated in the formula below. M max. = 1 Nm Reinforced through drives are available for applications with higher transfer torques and/or rotational vibrations. Customized designs available on request. N N, F p 1 V 1 p 2 V 2 p 3 V 3 M M max. p 1 V 1.177 + p 2 V 2.177 + p 3 V 3.177 p [bar] V [cm 3 /rev]

16/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Unit dimensions Standard range 45.5 ±.6 B ±1 9 ±.2 A ±.4 11 ±.135 88.4 ±.2 R 1 ±.5 Ø1.54 18.75 ±1 2 45 45 122.5 ±1.5 132 ±.2 44.2 ±.1 55 ±1.5 153 ±1.5 1:5 Ø22 ±.5 12.5 ±1.5 18 55 ±.15 M8 depth 13 11 ±1.5 1.5 ±.4 5 42'38" ±1' 92.2 As shown in drawing Inlet and outlet port changed 3.8 ±.2 2.5 ±.1 DIN 128-A14-FSt 55 ±.15 26 M8 depth 13 Ø95.2.15 45 45 M14x1.5-m-6 4x6.5 DIN 6888 A 51 3 1 Ordering code: AZPN 11 C B M B Displacement Ordering-No. Max. operating pressure n N [cm 3 /rev] L R [bar] [rpm] A B 51 625 335 51 625 35 2 5.4 52 19.8 22.5 2 53.5 112.8 25 51 725 352 51 725 47 2 5.6 55 115.8 28 51 725 364 51 725 55 2 28 5.7 56.5 118.8 32 51 725 353 51 725 48 28 5.9 59 123.3 Max. rotation speed kg Dimension [mm]

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 17/24 Unit dimensions Standard range 9.5 B±1 ±.1 A ±.4 SAE-B flange R ±1.1 Ø11.6.5 18.75 ±1 45 45 55 ±.15 122.5 +1.5 1 42 ±2 18 146 ±.15 12.5.4 31 Ø14.3 ±.27 Ø26 55 ±.15 M8 depth 13 174 ±1.3 Ø21.86.127 92.2 As shown in drawing Inlet and outlet port changed Min..1 usable shaft length Splined shaft ANSI B 92.1 13T 16/32 DP Tooth thickness sw = 2.155.3 Profile offset = -.262 55 ±.15 26 M8 depth 13 45 45 A 51 341 1 Ordering code: AZPN 1X D C M B AZPN 1X D C K B* Displacement nordering-no. N Max. operating pressure speed [mm] Max. rotation kg Dimension [cm 3 /rev] L R [bar] [rpm] A B 2 52 11.1 22.5 2 53.5 112.6 25 51 725 377 51 725 57 2 5.5 55 115.3 25 51 725 94* 2 5.5 55 115.3 28 51 725 431 51 725 58* 28 2 5.7 56.5 118.3 36 51 725 363 51 725 155 2 18 6. 61 127.3

18/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Unit dimensions Standard range 9.5 ±.1 A ±.4 B ±1 SAE-B flange R ±1.1 Ø11.6.5 18.75 ±1 22.2 ±.25 122.5 1 +1.5 42 ±2 Chamfer on locating collar AK Standard N6.11 41 ±.4 max. 3 18 47.6 ±.25 M1 depth 14 1.4 Ø14.3 ±.27 146 ±.15 174 ±1.3 Ø24 Ø51 Ø21.86.127 Ø22.1 92.2 As shown in drawing Inlet and outlet port changed 8 ±.5 13.2 ±1 Min. 23 usable shaft length Splined shaft ANSI B 92.1 13T 16/32 DP 26 Tooth thickness sw = 2.261.3 52.4 ±.25 M1 depth 14 26.2 ±.25 47.6 ±.25 18 M1 depth 14 22.2 ±.25 Version 1 Version 2 A 51 341 81 Ordering code: AZPN 11 D C 7 K B S23 Displacement Ordering-No. Max. operating pressure n N [cm 3 /rev] L R [bar] [rpm] A B 51 625 38 51 625 73 2 5.3 52 19.8 2 22.5 51 725 4 51 725 13 2 5.4 52 112.8 1 25 51 725 5 51 725 14 2 5.5 55 115.8 1 28 51 725 6 51 725 15 2 28 5.7 56.5 118.8 1 32 51 725 7 51 725 16 28 5.8 59 123.3 1 36 18 2 61 127.8 1 Max. rotation speed kg Dimension [mm] Version

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 19/24 Unit dimensions Standard range C ±1.2 B ±.7 9.5 ±.1 A ±.4 SAE-B flange R ±1.1 Ø11.6.5 18.75 ±1 22.2 ±.25 42 ±2 Chamfer on locating collar AK Standard N6.11 41 ±.4 1.4 18 47.6 ±.25 M1 depth 14 146 ±.15 174 ±1.3 Ø51 122.5 1 +1.5 Ø21.86.127 max. 3 Ø14.3 ±.27 Ø22.1 Ø24 Pump section I Pump section II 92.2 As shown in drawing Inlet and outlet port changed 8 ±.5 13.2 ±1 Min. 23 usable shaft length Splined shaft ANSI B 92.1 13T 16/32 DP Tooth thickness sw = 2.261.3 at cm3 /rev at cm 3 /rev 47.6 ±.25 52.4 ±.25 26 18 M1 depth 14 22.2 ±.25 26.2 ±.25 at cm 3 /rev A 51 345 87 Ordering code: AZPNN 11 D C 7 7 K B S23 Displacement [cm 3 /rev] Displacement [cm 3 /rev] Ordering-No. Max. operating pressure Max. operating pressure Max. rotation speed kg Dimension [mm] n N P I P II L R [bar] P I [bar] P II [rpm] A B C 51 665 461 51 665 149 2 2 9.9 52. 1.7 217.9 22.5 51 765 369 2 2 1. 53.5 163.6 222.7 22.5 22.5 51 765 38 51 765 86 2 2 1.1 53.5 165.2 225.7 25 51 765 67 2 2 1.1 55. 166.6 225.7 25 22.5 51 765 68 2 2 1.2 55. 168.2 228.7 25 25 51 766 315 51 765 69 2 1.3 55. 169.7 229.9 32 32 51 765 37 51 768 34 1 2 1.9 29. 181.2 244.9

/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Unit dimensions Standard range C ±1.2 9.5 ±.1 B ±.7 A ±.4 SAE-B flange R ±1.1 Ø11.6.5 18.75 ±1 22.2 ±.25 15.7 1 42.5 ±.5 45 45 1 1 +1.5 42 ±2 Chamfer on locating collar AK Standard N6.11 Ø51 Ø21.86.127 41 ±.4 max. 3 18 47.6 ±.25 1.4 Ø14.3 ±.27 Ø22.1 Ø24 M1 depth 14 Pump section I 15 35 ±.15 M6 depth 13 Pump section II 84.2 92.2 146 ±.15 174 ±1.3 8 ±.5 13.2 ±1 Min. 23 usable shaft length Splined shaft ANSI B 92.1 13T 16/32 DP 26 Tooth thickness sw = 2.261.3 18 47.6 ±.25 52.4 ±.25 at cm 3 /rev at cm 3 /rev ±.15 (15) at 4 and 5.5 cm 3 /rev M6 depth 13 22.2 ±.25 26.2 ±.25 124.5 ±1.3 As shown in drawing Inlet and outlet port changed M1 depth 14 45 45 at cm 3 /rev A 51 345 82

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 21/24 Ordering code: AZPNF 1X D C 7 K B S23 AZPNF 1X D C 7 K B S81* AZPNF 1X D C 7 M B S81** Displacement [cm 3 /rev] Displacement [cm 3 /rev] Ordering-No. Max. operating pressure Max. operating pressure Max. rotation speed kg Dimension [mm] n N P I P II L R [bar] P I [bar] P II [rpm] A B C 4 51 665 181 2 28 52. 141.5 184.2 22.5 8 51 765 387* 51 765 78 2 28 8.4 53.5 147.9 193.8 22.5 11 51 765 381 51 765 62 2 28 8.5 53.5 151.7.6 25 4 51 766 316 2 28 55. 147.6 19.2 25 11 51 765 377 51 765 79 2 28 8.6 55. 154.7 3.6 25 14 51 766 14** 2 2 8.7 55. 155.2 6.8 25 16 51 765 8 2 2 8.8 55. 155.2 21.2 28 11 51 765 92 2 28 28 8.7 56.5 157.7 6.6 28 16 51 765 384 51 765 63 2 2 28 8.9 56.5 158.2 213.2 28 19 51 766 314 51 767 58 28 9. 56.5 158.2 219.8 28 22.5 51 767 45 2 21 9.2 56.5 165.8 223.6 28 22.5 51 767 322* 2 1 21 9.3 56.5 165.8 223.6 32 8 51 765 64 28 2 8.8 59. 158.4 4.3 32 11 51 768 3 51 765 65 28 2 8.9 59. 162.2 211.1 32 14 51 765 378 2 2 9. 59. 162.7 216.1 32 16 51 765 66 2 2 9.1 59. 162.7 217.7 32 22.5 51 768 318* 1 21 59. 17.3 229.9 Fittings Fittings can be used for rectangular flange see page 7 Gear pump flange, 9 angle LA L3 L4 LA Ø DB LK L1 L2 L5 S1 Ø D3 Ø D1 Ø D1 LK D1 D3 L1 L2 L3 L4 L5 LA S1 DB Screws Seal Mass Part number p 2x 2x ring kg (bar) 55 S 17 45 34.5 24.. 56. 58 36 8.4 M 8x25 M 8x 33x2.5.44 1 515 72 4 2 55 S 26 49 35.5 32.. 62. 58 8.4 M 8x25 M 8x 33x2.5. 1 515 72 6 2 55 35L 31 49 38.5 32. 51.5 62. 58 8.4 M 8x25 M 8x 33x2.5.47 1 515 72 5 1 55 42 L 38 49 38.. 64.5 61. 58 8.4 M 8x25 M 8x7 33x2.5. 1 515 72 19 1 Complete fittings with seal ring, metric screw set, nuts and olive. Note You can find the permissible tightening torques in our publication: General Operating Instructions for External Gear Units RE 7 12-B1.

22/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Service parts Single pump 3 Multiple pump 31 Page Ordering code Seal kit N Pos. 8 NBR Seal kit F Pos. 8 NBR Shaft seal ring Pos. 3 Dimension Seal ring Pos. 3.1 Material Dimension 16 AZPN 1X C B M B 15171226 1512823 x22x7 NBR 17 AZPN 1X D C M B 15171226 1512823 x22x7 NBR 17 AZPN 1X D C K B 15171226 1512828 x22x7 FPM (SSR) 18 AZPN 1X D C 7 K B S23 15171226 1512828 x22x7 FPM (SSR) 19 AZPNF 1X D C 7 7 K B S23 15171226 151718 1512828 x22x7 1512143 FPM (SSR) x2.5 FPM AZPNF 1X D C 7 K B S81 15171226 151718 1512828 x22x7 1512143 FPM (SSR) x2.5 FPM AZPNF 1X D C 7 M B S81 15171226 151718 1512828 x22x7 1512143 FPM (SSR) x2.5 FPM AZPNN 1X D C 7 K B S23 15171226 15171226 1512828 x22x7 1921145 FPM (SSR) 45x2.5 NBR NBR = Perbunan FPM = Viton

AZPN RE 1 91/2.7 Hydraulics Bosch Rexroth AG 23/24 Notes for commissioning Fill pump with hydraulic fluid before installation. Check direction of rotation. Avoid axial and radial forces when mounting the couplings. Pipelines to be cleaned of dirt, cinders, sand, chips etc. Pipes, in particular must be pickled or rinsed. The introduction of external forces through pipe or hose lines is to be avoided. During the initial startup the overall hydraulics system is to be carefully vented. Vertical installations, in particular, with a drive shaft pointing upwards may result in air inclusions near the shaft seal ring. Cover up radial lip-type shaft seal ring when spraying and painting. Observe parameters, in particular, speeds and pressures as well as negative pressure in the suction line. Allow pump to run without load and have it deliver in depressurized state for several seconds to ensure it is sufficiently lubricated. Do not allow pump to run without any oil. If, after approx. seconds, the pump is still operating without bubbles then the system should be checked again. Once the operating values have been reached, check pipe connections for signs of leaks. Check operating temperature. Filter recommendation The major share of premature failures in gear pumps is due to contaminated hydraulic fluid. As a warranty cannot be issued for dirt-specific wear, we recommend filtration compliant with cleanliness level 21/18/15 ISO 46, which reduces the degree of contamination to a permissible dimension in terms of the size and concentration of dirt particles: We recommend that a full-flow filter always be used. Basic contamination of the hydraulic fluid used may not exceed class 19/16 as under ISO 46. Experience has shown that new fluid quite often lies above this value. In such instances a filling device with special filter should be used. Important notes Assembly, maintenance and repair of the pumps to be performed by authorized, skilled and instructed personnel only. Pump to be operated at specified data only (see page 12). Pump to be operated in proper working condition only. System to be depressurized when work conducted on pump. Arbitrary conversions and modifications, which affect safety and function are not allowed. Mount safety devices (e.g. coupling protection) or do not remove existing ones. Make sure that all fixing screws are tight (observe specified tightening torque values). General safety and accident prevention regulations must be adhered to. Project planning notes Comprehensive notes and suggestions are available in Hydraulics Trainer, Volume 3 RE 281, Project planning notes and design of hydraulic systems. Where external gear pumps are used we recommend that the following note be adhered to. Technical data All stated technical data is dependent on production tolerances and is valid for specific marginal conditions. Note that scattering is therefore possible, and at certain marginal conditions (e.g. viscosity) the technical data may change. Characteristics When configuring the engine, note the maximum possible application data based on the characteristics shown on pages 9 and 1. You can find further information in our publication: General Operating Instructions for External Gear Units RE 7 12-B1. General The pumps supplied by us have been checked for function and performance. No modifications of any kind may be made to the pumps; any such changes will render the warranty null and void! Repairs may only be made by the manufacturer or its authorized dealers and subsidiaries. Repairs conducted on their own will render the warranty null and void.

24/24 Bosch Rexroth AG Hydraulics AZPN RE 1 91/2.7 Ordering-No. Ordering-No. Page Ordering-No. Page 51 625 35 16 51 625 73 18 51 625 335 16 51 625 38 18 51 665 149 19 51 665 181 21 51 665 461 19 51 725 47 16 51 725 48 16 51 725 55 16 51 725 57 17 51 725 58 17 51 725 94 17 51 725 13 18 51 725 14 18 51 725 15 18 51 725 16 18 51 725 155 17 51 725 352 16 51 725 353 16 51 725 363 17 51 725 364 16 51 725 377 17 51 725 4 18 51 725 5 18 51 725 6 18 51 725 7 18 51 725 431 17 51 765 62 21 51 765 63 21 51 765 64 21 51 765 65 21 51 765 66 21 51 765 67 19 51 765 68 19 51 765 69 19 51 765 78 21 51 765 79 21 51 765 8 21 51 765 86 19 51 765 92 21 51 765 369 19 51 765 37 19 51 765 377 21 51 765 378 21 51 765 38 19 51 765 381 21 51 765 384 21 51 765 387 21 51 766 14 21 51 766 314 21 51 766 315 19 51 766 316 21 51 767 45 21 51 767 58 21 51 767 322 21 51 768 34 19 51 768 318 21 51 768 3 21 Bosch Rexroth AG Hydraulics Product Unit Drives External Gear Units Robert-Bosch-Straße 2 D-7171 Schwieberdingen Phone +49 () 711-811 1 63 Fax +49 () 711-811 17 98 brm-az.info@boschrexroth.de www.boschrexroth.com/brm This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be reproduced or given to third parties without its consent. The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgement and verification. It must be remembered that our products are subject to a natural process of wear and aging.