STION 1 STNR 1/4" RM PNLS 3/4" OVRLY PNLS STION 2 LUSH INST
OVRLL IMNSIONS STNR 25 1/2" (64.8) 36" (91.5) 23 7/8" (60.7) 1 3/4" (4.4) 13 1/2" (34.3) *84" (213.4) *83 1/2" (212.1) 68 1/2" (174.0) *72 1/4" (183.5) SPIITIONS Overall Width Overall Height Overall epth oor learance utout Width 36" (91.44 cm) 84" (213.36 cm) 25 3/8"(64.453 cm) 20 5/8" (52.4 cm) 35 1/2" (90.2 cm) utout Height 83 1/2" - 84 1/2" (212.1-214.6 cm) utout epth Plumbing Requirements Shipping Weight 24" (61 cm) 1/4" O copper tubing or G Smartonnect kit 675 lb (306.2 kg) *40" (101.6) *3 3/4" (9.5) RONT VIW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. ** llow 13" (33.0) min clearance for 130 door swing 35" (89.0) ase width *3 1/2" (8.9) ** llow 15" (38.1) min clearance for 130 door swing SI VIW TTNTION LTRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. ** llow 4" (10.2) min clearance to a wall for 90 door swing TOP VIW ** llow 4" (10.2) min clearance to a wall for 90 door swing 20 5/8" (52.4) ** These refrigerators are equipped with a 2-position door stop. The factory-set 130 door swing can be adjusted to 90 if clearances to adjacent cabinets or walls is restricted. llow full 130 door swings for pan removal. If the 90 door stop position is used, pan access is maintained, but pan removal is restricted. imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.
STNR TOP VIW STNR 3 1/8" 24" (61) (7.93) 35 1/2" (90.2) 7/16" (1.1) 1 9/16" Trim overlap (3.97) 6" (15.24) 5" (12.7) 20" (50.8) Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area. SI VIW W 3 1/2" (8.9) *84 1/2" (214.6) *Trim will overlap additional 7/16" 5" (12.7) WTR RONT VIW 5" (12.7) 75" (190.5 ) rom floor to bottom of electrical area 3 1/2" (8.9) The refrigerator will project forward, slightly beyond adjacent cabinetry. WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. ailure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. etermine your installation construction and required anti-tip configuration: Installed Under Soffit NTI-TIP RKT SOIT 2" x 4" ut to 35" Length fter installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exceed 24" deep. The top case trim overlaps the bottom of the soffit. SI VIW INSTLL UNR SOIT *84" (213.4) *Or installation height from floor SI VIW INSTLL WITH WOON WLL STUS N NO SOIT ZIS480X Screws mounted into vertical wall studs Top ase Trim Install Screws Through Trim and Into 3/4" Min. Wood race RONT VIW INSTLL WITH MTL WLL STUS N NO SOIT 3/4" Min. Side View Top ase Trim Wooden Wall Studs and No Soffit ut a 2" x 4" block and secure to brackets provided. Secure brackets to back wall of opening at 84" or your installation height from the floor. Metal Wall Studs and No Soffit This method requires securely fastened cabinets on both sides and a 3/4" minimum wood brace above unit, with it s front surface 24" from back wall. fter installing unit into opening, raise grille panel and attach metal case top trim to 3/4" minimum wood brace. The brace spanning the enclosure must be securely fastened to cabinets on both sides. See Installation Instructions for detailed instructions.
USTOM SI PNLS 1 7/8" (4.8) 24" (61.0) 3/16" (.5) *84 *84" (213.4) *epending on installation height STNR Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. *3" - 4" (7.6-10.2) *epending on installation height 2 9/16" (6.5)
1/4" RM PNL IMNSIONS ispenser utout G reezer 3/4" OVRLY PNL IMNSIONS ispenser utout G reezer Grille Grille resh ood resh ood PNL SSMLY ROSS STION Trim 1/4" ramed PNL IMNSIONS ispenser utout 9 5/8" (24.4) PNL SSMLY ROSS STION Trim 1/4" acker.10" Spacer 15 3/8" (39.1) PNL IMNSIONS oor Supplied Handles ISPNSR UTOUT POSITION oor 3/4" Overlay Supplied Handles.25" +.10" +.75" = 1.10" Total Thickness ispenser utout 9 5/8" (24.4) 15 3/8" (39.1) 1/4" ramed 33 7/8" 9" 68 3/8" 14 9/16" 18 9/16" G 17 13/16" 3 1/8" 1/4" acker 33 7/8" 9" 68 3/8" 14 9/16" 18 9/16".10" Spacer 33" 8 3/8" 67" 13 1/4" 17 1/4" 3/4" Overlay 34 1/8" 9 1/4" 68 5/8" 14 13/16" 18 13/16" *ISPNSR UTOUT POSITION G 17 15/16" 3 1/4" * ut the dispenser opening after the backer, spacer and overlay panels have been assembled. STNR Trimmed refrigerators are designed to be customized with decorative panels. ield-installed custom door and grille panels are required. 1/4" ramed s: or 1/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim. Maximum total panel weight: resh food door panel 75 lbs. reezer drawer panel 53 lbs. Grille panel 18 lbs 3/4" Overlay s: or 3/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. enter each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOT: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: resh food door panel 75 lbs. reezer drawer panel 53 lbs. Grille panel 18 lbs oor Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. ustom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHSS2: uropean tubular stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle. Order 2 kits for side-by-side refrigerators from your Monogram supplier.
ISPNSR TRIM 1/4" ramed reezer oor Ice/Water ispenser 1/4" Total Thickness 3/4" Overlay 1/4" acker.10" Spacer reezer oor Ice/Water ispenser 1/4" PNL ISPNSR TRIM 3/4" OVRLY PNL ISPNSR TRIM RIS OVRLY PNL SIGN ON ISPNSR MOLS 16 3/4" 10 5/8" ISPNSR TRIM 1/4" acker.10" Spacer 3/4" Overlay 1.10 Total Thickness 1.10" Total Thickness SI VIW ROSS STION (SHOWING RIS OVRLY WITH MIL RIL) STNR These refrigerators are supplied with two dispenser trims, one for framed panels and one for overlay panels. 1/4" ispenser Trim: The framed panel must be 1/4" nominal thickness to fit the dispenser trim. The dispenser trim fits over the custom panel and snaps into the freezer door. If the panel is less than 0.250" thick, a noticeable gap may be created around the dispenser trim. oam tape may be applied on the door to improve the fit. If the panel is more than 0.250" thick, the dispenser trim cannot be secured to the door. 3/4" Overlay ispenser Trim: The 3/4" overlay dispenser trim is designed to fit a total panel thickness of 1.100". If the panel is less than 1.100" thick, a noticeable gap may be created around the dispenser trim. If the panel is more than 1.100" thick, the dispenser trim cannot be secured to the door. The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness. lternative panel construction methods such as securing a 3/4" panel to a 1/4" backer panel cannot be used. nother method, routing a 3/4"-thick panel on all sides, cannot be used. These methods will not result in the required 1.100" panel thickness. When a raised panel design is to be used, a custom middle rail is required. Raised Overlay esign on ispenser Models: When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim. The middle rail must be wide enough to allow for the dispenser trim to overlap the opening. The middle rail must be 1.10" total thickness to accept the dispenser trim.
OVRLL IMNSIONS TR PNL INSTLL 38" (96.5) LUSH INST 26" (66.0) 20 5/8" (52.4) 11 11/16" (29.7) 15 3/8" (39.1) 84 1/2" (214.6) 72 5/8" (184.5) * 83 1/2" (212.1) 68 5/8" (174.3) *39 17/32" (100.4) SPIITIONS Overall Width 38" (96.5 cm) Overall Height 84 1/2" (214.6 cm) Overall epth 26" (66.0 cm) oor learance utout Width utout Height utout epth Plumbing Requirements Shipping Weight 20 5/8" (52.4cm) 39" (99.1 cm) 85" (215.9cm) 26 3/16" (66.5 cm) 1/4" O copper tubing or G Smartonnect kit 675 lb (306.2 kg) imensions include 3/4" custom cabinet panel RONT VIW Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84". **13" (33.0) 35" (89.0) ase width **15" (38.1) 4" (10.2) SI VIW TTNTION LTRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. ** llow 4" (10.2) min clearance to a wall for 90 door swing *115 oor swing oors can be adjusted to 90 door swing TOP VIW ** llow 4" (10.2) min clearance to a wall for 90 door swing 20 5/8" (52.4) ** These refrigerators are equipped with a 2-position door stop. The factory-set 115 door swing can be adjusted to 90 if clearances to adjacent cabinets or walls is restricted. llow a 15" minimum clearance to wall for pan removal. If the 90 door stop position is used, pan access is maintained, but pan removal is restricted. imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.
LUSH INST 3/4" PNLS 85" (215.9) 26 3/16" (66.5) lush inset depth 20 15/16" (53.2) epth to cleat inished cleats 5 1/4" (13.3) 3/4" (1.9) Width of side cleats 85" (215.9) 3/4" TOP VIW inished cleats ase Trim 39" (99.1) lush inset width 37 1/2" (95.3) Width between cleats 6" (15.2) ase oor 5" (12.7) 12" (30.5) 1/2" (1.3) 75" (190.5 ) rom floor to bottom of electrical area LUSH INST Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area. WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. ailure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. W SI VIW NTI-TIP RKT SOIT 3 1/2" (8.9) 7" (17.8) WTR RONT VIW 7" (17.8) 2" x 4" ut to 35" Length 3 1/2" (8.9) etermine your installation construction and required anti-tip configuration: ut a 1" x 4" block 35" long. Measure and mark under the soffit, 5 1/4" from the front edge of the cabinet. Secure the wood block under the soffit. rom the bottom of the block to the finished floor should measure 84". Wooden Wall Studs and No Soffit ut a 2" x 4" block and secure to brackets provided. Secure brackets to back wall of opening at 84" or your installation height from the floor. Screws mounted into vertical wall studs *84" (213.4) *Or installation height from floor See Installation Instructions for detailed instructions. SI VIW INSTLL UNR SOIT SI VIW INSTLL WITH WOON WLL STUS N NO SOIT ZIS480X
LUSH INST 1/2" PNLS 5 3/8" (13.7) TOP VIW inished cleats ase Trim ase LUSH INST 26 3/16" (66.5) lush inset depth 20 13/16" (52.9) epth to cleat 3/4" (1.9) Width of side cleats 1/2" 39" (99.1) lush inset width 37 1/2" (95.3) Width between cleats 6" (15.2) oor 1/2" (1.3) Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area. 85" (215.9) inished cleats 85" (215.9) 5" (12.7) 12" (30.5) 75" (190.5 ) rom floor to bottom of electrical area WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. ailure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. W SI VIW NTI-TIP RKT SOIT 3 1/2" (8.9) 7" (17.8) WTR RONT VIW 7" (17.8) 3 1/2" (8.9) 2" x 4" ut to 35" Length etermine your installation construction and required anti-tip configuration: ut a 1" x 4" block 35" long. Measure and mark under the soffit, 5 3/8" from the front edge of the cabinet. Secure the wood block under the soffit. rom the bottom of the block to the finished floor should measure 84". Wooden Wall Studs and No Soffit ut a 2" x 4" block and secure to brackets provided. Screws mounted into vertical wall studs Secure brackets to back wall of opening at 84" or your installation height from the floor. *84" (213.4) *Or installation height from floor See Installation Instructions for detailed instructions. SI VIW INSTLL UNR SOIT SI VIW INSTLL WITH WOON WLL STUS N NO SOIT ZIS480X
LUSH INST 3/4" PNL IMNSIONS ispenser utout G reezer Grille resh ood PNL IMNSIONS 38" 11 3/16" 68 5/8" 16 7/8" 20 7/8" ispenser utout 9 5/8" (24.4) 15 3/8" (39.1) ISPNSR UTOUT POSITION G 17 23/32" 3 3/8" LUSH INST Trimmed refrigerators are designed to be customized with decorative panels. ield-installed 1/2" or 3/4" custom door and grille panels are required. or 3/4" raised door and grille panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door and grille trims. 3/4" RIS OOR PNL ROUTING 11/32" 1/4" TIL TOP 3/4" 1/4" 7/16" NOT: Routed areas should be finished as they may be visible when assembled. ront TOP MXIMUM TOTL PNL WIGHT: resh food door panels 75 lbs. reezer drawer panel 53 lbs. Grille panel 18 lbs. OOR HNLS oor handle not included. custom handle supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 30 1/2" long. ack ZKHSS2: uropean tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 64 1/4" long. 3/16" ack ront TIL OTTOM ORNR VIW SHOWING PITUR RM ROUTING TIL HING SI ROUTR PTH 1/4" TIL HNL SI 2 1/16" 3/16" HING SI ack HNL SI 3/4" PNL OTTOM VIW (TR ROUTING) OTTOM 3/4" PNL SI VIW (TR ROUTING)
3/4" RIS GRILL PNL ROUTING NOT: Routed areas should be finished as they may be visible when assembled. TIL TOP TOP LUSH INST ack ront 2" ROUTR PTH 1/4" ack ront Trimmed refrigerators are designed to be customized with decorative panels. ield-installed 1/2" or 3/4" custom door and grille panels are required. or 3/4" raised door and grille panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door and grille trims. ORNR VIW SHOWING PITUR RM ROUTING Maximum total panel weight: resh food door panels 75 lbs. reezer drawer panel 53 lbs. Grille panel 18 lbs. 3/16" TIL OTTOM OTTOM 3/4" PNL SI VIW (TR ROUTING) oor Handles oor handle not included. custom handle supplied by your cabinet maker may be used. TIL LT SI ROUTR PTH 1/4" ROUTR PTH 1/4" 2 1/16" 2 1/16" TIL RIGHT SI ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 30 1/2" long. ZKHSS2: uropean tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 64 1/4" long. ront LT SI RIGHT SI ack 3/4" PNL OTTOM VIW (TR ROUTING)
ISPNSR TRIM LUSH INST reezer oor 1/4" acker.10" Spacer reezer oor.85" Total Thickness Ice/Water ispenser Ice/Water ispenser These refrigerators are supplied with a dispenser trim for flush inset panels. 3/4" lush RIS PNL SIGN ON ISPNSR MOLS 16 3/4" 3/4" OVRLY PNL ISPNSR TRIM 1/2" Overlay 1/2" OVRLY PNL ISPNSR TRIM 3/4" or 1/2" lush ispenser Trim: The provided dispenser trim is designed to fit a total panel thickness of 3/4" or 0.85". If the panel is less than 3/4" thick, a noticeable gap may be created around the dispenser trim. If the panel is more than 0.85" thick, the dispenser trim cannot be secured to the door. The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness. When a raised panel design is to be used, a custom middle rail is required. 10 5/8" 3/4" or.85" Total Thickness Raised esign on ispenser Models: When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim. ISPNSR TRIM The middle rail must be wide enough to allow for the dispenser trim to overlap the opening. SI VIW ROSS STION The middle rail must be 3/4" total thickness for 3/4" panels or 0.85" total thickness for 1/2" panels to accept the dispenser trim. (SHOWING RIS PNL WITH MIL RIL)
LUSH INST 1/2" PNL IMNSIONS ispenser utout G reezer Grille resh ood PNL IMNSIONS 1/4" acker 33 7/8" 9" 68 3/8" 14 9/16" 18 9/16".10" Space 33" 8 3/8" 67" 13 9/16" 17 9/16" 1/2" Overlay 38" 11 3/16" 68 5/8" 16 7/8" 20 7/8" ispenser utout 9 5/8" (24.4) 15 3/8" (39.1) ISPNSR UTOUT POSITION G 17 23/32" 3 3/8" LUSH INST The 1/2" overlay panel must be secured to a.10" spacer panel and a 1/4" thick backer panel, which slides into the trim. ssemble the panels with glue and screws: enter the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel. 1/4" KR SSMLY ROUTING IMNSIONS Hinge Side Maximum total panel weight: resh food door panel 75 lbs. reezer drawer panel 53 lbs. Grille panel 18 lbs. oor 1/2" Overlay acker with Overlay ssembly reezer ack resh ood ack 1/4" acker.10" Spacer PNL IMNSIONS Grille ack resh ood 2 1/16" 1/16" 1/8" 1/8" reezer 2 1/16" 1/16" 1/8" 1/8" Grille 2 1/16" 2 1/16" 2" 7/32"
TURS N NITS L LIGHTING Light columns in the freezer and fresh food compartments extend the full length of the interior and L lighting located inside the vegetable and climate-control drawers illuminate contents without compromising space VN TMPRTUR MNGMNT SYSTM WITH MULTI-SHL IR TOWR Provides even distribution of air throughout the refrigerator LIMT-ONTROL RWR llows you to express-chill beverages, expressthaw meats and select specific temperatures for perishable foods ISPNSR WITH PROXIMITY SNSOR esigned to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away IRY IN WITH NTR IVIR Has a unique magnetic seal that locks in freshness ILTR-HNG INITOR LIGHT Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser G WTR ILTR Has been moved from the fresh food compartment to the overhead cabinet, where it is discreetly out of sight R