TANDEM plus BLUMOTION 569H/569. installation instructions

Transcription

1 TANDEM plus 569H/569. installation instructions inside Heavy duty full extension concealed runners Basic components Locking devices Runners New side adjustment New rear side adjustment Rotate side adjustment left or right equally After front side adjustment is made with the on both locking devices. Drawer front moves in the same direction as rotation. locking devices, rotate the rear side adjustment left or right to re-align the back of the box with the front. Drawer back moves in the same direction as rotation. 0 Height adjustment Press up on adjustment tab Push towards back of Tilt adjustment Rotate the tilt adjustment lever on the rear of each runner to lift the back of the and tilt the top of the front forward front R L R L Maximum (/8") rise of front (tool-free) Maximum 5 (/6") rise of back (tool-free) NOTE: Height and tilt adjustments available with all combinations of locking devices and runners 0 L R New depth adjustable locking device Locking device T5.90.PS with side, height and depth adjustment Depth adjustment on runner TANDEM 569 runners feature elongated holes that allow ±4.5 (/6") depth adjustment L R Maximum.5 (/6") to left or right on both front and rear (tool-free) NOTE: Side adjustment not available on T5.x8xx locking devices Turning the adjustment screw allows for up to a +.5 (/") out adjustment NOTE: For T5.90.PS setback in inset applications, see page 5 Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.

2 Drawer specifications Face frame and panel applications Preparing for hardware installation Front view opening width inside width = opening width minus 4 6 (/4") minimum top clearance Installation screw 606N or 606P 75 Locking device T5.90 with side adjustment or T5.80 without side adjustment pre-boring holes for locking devices #6 head wood or system screws 7 (-5/") (/6") side maximum 6 (5/8") (/") height maximum = opening minus 0 (5/") opening height pre-boring holes for rear hooks.5 mm bit with extension chuck 4 (9/6") bottom clearance 6 mm bit with stop collar TANDEM template T NOTE: Because material may vary, the inside width must equal opening width minus 4 for TANDEM to align and function properly NOTE: Use of the T TANDEM template is essential for accurate location and angle of pre-bored locking device holes and accurate boring for rear hook holes Drawer insertion Extend the runners fully. Place the on the runners and close. The locking devices automatically engage with the runners. Make adjustments if necessary. Drawer removal Squeeze orange handles on locking devices Pull straight out and up Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.

3 Face frame application Runner mounting specifications 786 (0-5/6") minimum face Cabinet and specifications depth 88 (") 76 (0") mounting position 0 (/") 8 (/4") typical setback (/8") 709 (7-9/") minimum B 76 (0") B 686 (7") blocking behind frame runner setback (/8") Target Drawer Length face mounting position 0 (/") 7 (-5/") 5 (/") minimum top clearance 6 (/4") maximum height = opening minus 0 (5/") gap.5 (/6") bottom clearance 4 (9/6") 686 (7") 64 (4-/") minimum B 60 (4") blocking behind frame bottom recess (/") 60 (4") 557 (-5/6") minimum 569H50B 5 (") TANDEM plus depth minimum B 88 (") 786 (0-5/6") 76 (0") maximum runner 777 (0-9/") B 76 (0") 709 (7-9/") 686 (7") 700 (7-9/6") B 686 (7") 64 (4-/") 60 (4") 6 (5/8") 65 (4-9/") detail of front holes 5 (") 480 (8-9/") minimum 569H4570B 457 (8") 569H50B 60 (4") 557 (-5/6") 5 (") 548 (-9/6") 569H4570B 5 (") 480 (8-9/") 457 (8") 47 (8-7/") NOTE: For heavy duty applications, rear brackets and sockets cannot be used. Cabinet sides must be blocked-out flush with the inside of the frame. (-/4") 4 (-/") 9 (/") typical 7 (9/") 7 (-5/") 5 (/") NOTE: Orange dots indicate screw locations required to meet specified load capacities T5.90R T5.90L T5.80R T5.80L 606N or 606P HG Locking device with side adjustment (right) Locking device with side adjustment (left) Locking device (right) Locking device (left) #6 Wood screw (for mounting runner to side, rear brackets and locking devices) #6 System screw (for mounting runner to side) Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.

4 Panel application Runner mounting specifications Cabinet and specifications mounting position 7 (-5/") face depth 8 (5-/") 4 (8-/6") 88 (") 8 (/4") typical setback (/8") B 76 (0") runner face 786 (0-5/6") minimum mounting position 7 (-5/") 7 (-5/") 76 (0") 8 (5-/") 709 (7-9/") minimum 4 (8-/6") B 686 (7") setback (/8") 5 (/") minimum top clearance 6 (/4") maximum height = opening minus 0 (5/") 8 (5-/") 4 (8-/6") gap.5 (/6") bottom clearance 4 (9/6") 686 (7") 64 (4-/") minimum B 60 (4") 56 (0-/") 4 (8-/6") bottom recess (/") 60 (4") detail of front holes (-/4") 4 (-/") 5 (") 9 (/") typical 7 (9/") 5 (/") 7 (-5/") 557 (-5/6") minimum 9 (7-9/6") 480 (8-9/") minimum 4 (8-/6") NOTE: Orange dots indicate screw locations required to meet specified load capacities 569H50B 5 (") 569H4570B 457 (8") TANDEM plus depth minimum B 88 (") 786 (0-5/6") 76 (0") maximum runner 777 (0-9/") B 76 (0") 709 (7-9/") 686 (7") 700 (7-9/6") B 686 (7") 64 (4-/") 60 (4") 6 (5/8") 65 (4-9/") 569H50B 60 (4") 557 (-5/6") 5 (") 548 (-9/6") 569H4570B 5 (") 480 (8-9/") 457 (8") 47 (8-7/") T5.90R T5.90L T5.80R T5.80L 606N or 606P HG Locking device with side adjustment (right) Locking device with side adjustment (left) Locking device (right) Locking device (left) #6 Wood screw (for mounting runner to side, rear brackets and locking devices) #6 System screw (for mounting runner to side) 4 Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.

5 Inset application Face frame application complete blockout (see table) Trial recommended Panel application (see table) Trial recommended blocking behind frame minimum = runner + setback + 6 (/4") range minimum = runner + setback + 6 (/4") Setback information Runner setback when using depth adjustable locking device (T5.90.PS) sub-front mounting hole position front NOTE: Runner cannot be mounted below opening 56/569 H/. sub-front (/") 0 (5/") (9/") 6 (-/") 6 (5/8") (9/") 6 (-/") 9 (-5/") 9 (/4") 6 (-/") 9 (-5/") (-/4") 6 (5/8") 9 (/4") (7/8") calculating Runner setback when using all other locking devices front Setbacks in this table recess the face of the front inside of the (/") The depth adjustment can then be used to move the front out to its desired position,.5 (/") out adjustment only 56/569 H/. sub-front + front minus 9 (/") 56/569 H/. sub-front (/") 7.5 (/6") 0.5 (/6").5 (5/6") 6 (5/8") 0.5 (/6").5 (5/6") 6.5 (-/") 9 (/4").5 (5/6") 6.5 (-/") 9.5 (-5/") 6 (5/8") 9 (/4") (7/8") front Setbacks in this table set the face of the front flush with the face of the If a depth adjustable locking device is needed, please see the locking device and table above NOTE: For mounting hole position add 7 (9/") to calculating 56/569 H/. sub-front + front minus.5 (7/6") 5 Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.

6 Attachment specifications Depth adjustment specifications B A 0.5 (/6") setback Mount each runner using at least two of the elongated holes. Install the to check the position of the front. Remove the, loosen screws and make adjustments if necessary, ±4.5 (/6"). Tighten the screws, verify the front position and finish mounting the runners using the screw locations indicated by the orange dots. TANDEM plus A B 44.5 (9-5/8") 7.5 (4-/") B 44.5 (9-5/8") 7.5 (4-/") B 44.5 (9-5/8") 7.5 (4-/") 569H50B 44.5 (9-5/8") (9-/") 569H4570B 44.5 (9-5/8") 46.5 (7-/6") B Millimeter to inch conversion chart / /6 / /8 5 / /6 7 / /4 9 / 5 /6 / /8 / 7 /6 5 / / 7 / 9 /6 9 / 5 /8 / /6 / /4 5 / /6 7 / 7 /8 9 / 5 /6 / 6 Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc. INST-TDM569H