SCHEDULED MINTENNCE INTERVLS (M Y ODY CHEVROLET CORVETTE) TO E SERVICED TYPE OF SERVICE VEHICLE MILEE INTERVL (x1000) 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75 82.5 90 97.5 oil & filter R rake hoses & brake lining S/I Coolant level, hoses & clamps S/I Exhaust system & throttle linkage S/I Lubricate chassis, suspension, steering linkage, transaxle shift linkage, parking brake cable guides, underbody contact points & linkage S/I Rear axle fluid level S/I utomatic transaxle fluid & filter S/I ir filter element R coolant C R Ignition cables, ER & fuel systems S/I Serpentine drive belt S/I Spark plugs D R R: Replace S/I: Service or Inspect engines require a special oil meeting M Standard 4718M. utomatic transaxle fluid & filter: replace at 100,000 miles (if not changed previously). C coolant: replace every 100,000 miles. Use O.E. specified (DEX-COOL ) coolant only. If any silicate coolant is used, the service interval is every 30,000 miles. D Platinum tip spark plugs: replace every 100,000 miles. FREQUENT OPERTION MINTENNCE (SEVERE SERVICE) If a vehicle is operated under any of the following conditions it is considered severe service: - Extremely dusty areas. - 50% or more of the vehicle operation is in 32 C (90 F) or higher temperatures, or constant operation in temperatures below 0 C (32 F). - Prolonged idling (vehicle operation in stop and go traffic). - Frequent short running periods (engine does not warm to normal operating temperatures). - Police, taxi, delivery usage or trailer towing usage. oil & oil filter: change every 3000 miles Chassis lubrication: lubricate every 6000 miles. Lubricate suspension, parking brake cable guides, underbody contact points & linkage: lubricate every 6000 miles. ir filter element: service or inspect every 15,000 miles. utomatic transmission fluid & filter: change every 15,000 miles.
RKE SPECIFICTIONS ll measurements in inches unless noted Minimum rake Caliper rake Disc Lining racket Mounting Original Minimum Maximum Thickness olts olts Model Thickness Thickness Runout Front Rear (ft. lbs.) (ft. lbs.) 0.006 0.030 0.030 C 0.006 0.030 0.030 C 0.006 0.030 0.030 C 0.006 0.030 0.030 C Heavy duty: 1.110; Std.: 0.795 Heavy duty: 1.059; Std.: 0.744 C Front: not available, Rear: upper 26 ft. lbs., lower 16 ft. lbs.
Model Displacement Liters (cc) ID/VIN CPCITIES Oil with Filter (qts.) 5.7 (5737) 5.7 (5737) 5.7 (5737) 5.7 (5737) 6.5 6.5 6.5 6.5 3.8 3.8 3.8 3.8 20.0 20.0 20.0 20.0 14.7 14.7 14.7 14.7 NOTE: ll capacities are approximate. dd fluid gradually and ensure a proper fluid level is obtained. MM 6 speed trans: 4.1 pts. 4L60E trans: 10.0 pts. Transmission (pts.) 6-Spd uto. Drive xle (pts.) Fuel Tank (gal.) Cooling System (qts.)
CRNKSHFT ND CONNECTIN ROD SPECIFICTIONS ll measurements are given in inches. Crankshaft Displacement Main rg. Main rg. Oil Shaft Thrust Journal Liters (cc) ID/VIN Journal Dia. Clearance End-play on No. Diameter 2.558-0.0007-0.0015-5 2.0987 2.559 0.0078 2.558-0.0007-0.0015-5 2.0987 2.559 0.0078 2.558-0.0007-0.0015-5 2.0987 2.559 0.0078 2.558-0.0007-0.0015-5 2.0987 2.559 0.0078 Connecting Rod Oil Clearance 0.0006-0.0025 0.0006-0.0025 0.0006-0.0025 0.0006-0.0025 Side Clearance 0.0043-0.0200 0.0043-0.0200 0.0043-0.0200 0.0043-0.0200
ENINE ND VEHICLE IDENTIFICTION Model Code Liters (cc) Cu. In. Cyl. Fuel Sys. Type Eng. Mfg. Code 350 8 SFI OHV CPC W CPC: Chevrolet/Pontiac/Canada X MFI: Multi-point Fuel Injection Y OHV: Over Head Valves 1 2001 8th position of VIN 2 2002 10th position of VIN
ENINE TUNE-UP SPECIFICTIONS Ignition Idle Spark Plug Timing Fuel Speed Valve Displacement ap (deg.) Pump (rpm) Clearance Liters (cc) ID/VIN (in.) MT T (psi) MT T In. Ex. 0.060 48-55 HYD HYD 0.060 48-55 HYD HYD 0.060 48-55 HYD HYD 0.060 48-55 HYD HYD NOTE: The Vehicle Emission Control Information label often reflects specification changes made during production. The label figures must be used if they differ from those in this chart. HYD: Hydraulic Refer to Vehicle Emission Control Information label
Model SFI: Sequential Fuel Injection Displacement Liters (cc) ENERL ENINE SPECIFICTIONS Series (ID/VIN) Fuel System Net Horsepower @ rpm Net Torque @ rpm (ft. lbs.) ore x Stroke (in.) Compression Ratio Oil Pressure @ rpm SFI SFI SFI SFI 345@5600 345@5600 345@5600 345@5600 350@4400 350@4400 350@4400 350@4400 3.89x3.62 3.89x3.62 3.89x3.62 3.89x3.62 10.1:1 10.1:1 10.1:1 10.1:1 18@ 18@ 18@ 18@
PISTON ND RIN SPECIFICTIONS ll measurements are given in inches. Ring ap Ring Side Clearance Displacement Piston Top ottom Oil Top ottom Liters (cc) ID/VIN Clearance Compression Compression Control Compression Compression 0.0007-0.009-0.017-0.007-0.0016-0.0016-0.015 0.025 0.027 0.0033 0.0031 0.0007-0.009-0.017-0.007-0.0016-0.0016-0.015 0.025 0.027 0.0033 0.0031 0.0007-0.009-0.017-0.007-0.0016-0.0016-0.015 0.025 0.027 0.0033 0.0031 0.0007-0.009-0.017-0.007-0.0016-0.0016-0.015 0.025 0.027 0.0033 0.0031 Oil Control 0.0004-0.0087 0.0004-0.0087 0.0004-0.0087 0.0004-0.0087
OEM Tires Tire Pressures (psi) Wheel all Joint Model Standard Optional Front Rear Size Inspection Fr: P245/45ZR17 None 30 30 8.5 U: 0.125 in. Rr: P275/40ZR18 L: 0.047 in. Fr: P245/45ZR17 None 30 30 8.5 U: 0.125 in. Rr: P275/40ZR18 L: 0.047 in. Fr: P245/45ZR17 None 30 30 8.5 U: 0.125 in. Rr: P275/40ZR18 L: 0.047 in. Fr: P245/45ZR17 None 30 30 8.5 U: 0.125 in. Rr: P275/40ZR18 L: 0.047 in. OEM: Original Equipment Manufacturer PSI: Pounds Per Square Inch L:Lower U:Upper Fr: Front Rr: Rear TIRE, WHEEL ND LL JOINT SPECIFICTIONS
TORQUE SPECIFICTIONS ll readings in ft. lbs. Cylinder Main Rod Crankshaft Displacement Head earing earing Damper Flywheel Liters (cc) ID/VIN olts olts olts olts olts C D E C D E C C D D E E Intake F F F F Manifold Exhaust Spark Plugs 11 11 11 11 Lug Nut 100 100 100 100 M11 bolts: 22 ft. lbs. C Step 1: 15 ft. lbs. M11 bolts: plus 90 degrees Step 2: Rotate 75 degrees M11 bolts 1<en dash>8: plus 90 degrees D Step 1: 240 ft. lbs. M11 bolts 9<en dash>10: plus 50 degrees Step 2: Install a new bolt and tighten to 37 ft. lbs. M8 bolts (11<en dash>15): 22 ft. lbs. Step 3: Rotate 140 degrees Inner olts: E Step 1: 15 ft. lbs. Step 1: 15 ft. lbs. Step 2: 37 ft. lbs. Step 2: 80 degrees Step 3: 74 ft. lbs. Side bolts: 18 ft. lbs. F Step 1: 44 inch lbs. Outer studs: Step 2: 89 inch lbs. Step 1: 15 ft. lbs. Step 1: 11 ft. lbs. Step 2: 53 degrees Step 2: 18 ft. lbs.
Displacement Liters (cc) ID/VIN Seat ngle (deg.) 46 46 46 46 VLVE SPECIFICTIONS Face ngle (deg.) 45 45 45 45 Spring Test Pressure (lbs. @ in.) 76@1.80 76@1.80 76@1.80 76@1.80 Spring Installed Height (in.) 1.80 1.80 1.80 1.80 Intake Stem-to-uide Clearance (in.) Exhaust Stem Diameter (in.) Intake Exhaust N N N N N N N N N: Not vailable
WHEEL LINMENT Caster Camber Steering Preferred Preferred xis Range Setting Range Setting Toe-in Inclination Model (+/-Deg.) (Deg.) (+/-Deg.) (Deg.) (in.) (Deg.) F +6.90-0.20 0.05 +/- 0.10 R -0.18 0 +/- 0.10 F +6.90-0.20 0.05 +/- 0.10 R -0.18 0 +/- 0.10 F +6.90-0.20 0.05 +/- 0.10 R -0.18 0 +/- 0.10 F +6.90-0.20 0.05 +/- 0.10 R -0.18 0 +/- 0.10