GASKETS From compound asbestos free and PTFE sheets, our sealing solutions. COMPRESSED SYNTHETIC FIBRE JOINTING SHEETS Seal X offers a number of asbestos free synthetic fibre jointing sheets designed for a wide range of applications required for specific sealing solutions. A wide range of grades are available for many different applications. The jointing can be supplied as a sheet or cut gaskets, both supplied in either or non- dimensions. PTFE PRODUCTS Seal X offers a comprehensive range of modified and expanded PTFE sealing products designed for applications where chemical resistance is paramount or where food safety is a requirement. Our modified PTFE is reinforced with heat resistant filler. The modification of the molecular structure of the polymer and a special production process that determines the isotropic orientation of the components in the plane of the gasket, form the basis of the outstanding mechanical characteristics of this material that combine with the already wellknown excellent chemical properties of the PTFE. The seal capacity is excellent at low compression and at elevated temperatures. APPLICATIONS Seal X products are recommended for reducing leakages with chemically aggressive substances. These products are ideal for the chemical, petro-chemical, paper mill, oil, gas, food, and pharmaceutical applications. We strive to provide customers with leading solutions and high performance products to suit all specific needs. Please contact our Technical Sales Team INDEX OF GASKETS SX 2200 10 SX 2201 11 SX 2202 12 SX 2203 13 SX 2204 14 SX 2205 15 SX 2206 16 SX 2207 17 SX 2208 18 SX 2209 19 SX 2210 20 SX 2211 21 SX 2213 22 SX 2214 23 SX 2600 24 SX 2601 25 SX 2602 26 8
SX2200 GASKETS SX2201 GASKETS SX 2200 SX2201 Max. working pressure MPa 4 Max. working pressure MPa 6 Continual 140 steam 120 Peak 210 Continual 220 steam 180 Peak 250 Application: water, gas, oil, alcohol, basic chemicals Application: water, water vapour, gas, oil, alcohol, basic chemicals DENSITY g.cm -3 1,7 2,1 DIN 28 090-2 DENSITY g.cm -3 1,6 2,0 DIN 28 090-2 RESIDUAL STRESS* 16 h/175 C! MPa 20 DIN 52 913 SPEC. LEAKAGE RATE! mg/(s.m) 0,1 DIN 3535 6 % 15 ASTM F 146 RESIDUAL STRESS* 16 h/175 C! MPa 20 DIN 52 913 RECOVERY min. % 45 ASTM F 36 J SPEC. LEAKAGE RATE! mg/(s.m) 0,06 DIN 3535 6 % 15 ASTM F 146 YELLOW branded on one side GREEN branded on one side SX 2200 SX2201 FA-Z-12-0 FA-MA-1-0 F 712 120 M4 F 712 111 M4 Code: wdb20 Code: wdb07 10
SX2202 GASKETS SX2203 GASKETS SX2202 SX2203 Max. working pressure MPa 10 Max. working pressure MPa 12 Continual 250 steam 200 Peak 400 Continual 250 steam 200 Peak 400 DENSITY g.cm -3 1,7 2,0 DIN 28 090-2 RESIDUAL STRESS* 16 h/175 C! MPa 30 DIN 52 913 SPEC. LEAKAGE RATE! mg/(s.m) 0,06 DIN 3535 6 BLUE branded on one side SX2202 FA-MA-1-0 F 712 111 M5 DENSITY g.cm -3 1,9 2,2 DIN 28 090-2 SPEC. LEAKAGE RATE! mg/(s.m) 0,08 DIN 3535 6 BLACK (both sides graphited) branded on one side SX2203 FA-MA-1-ST F 712 111 M7 Code: wdb22 Page: 1 of 1 Approved: 3.1.2012 Valid since: 4.1.2012 Code: wdb23 12
SX2204 GASKETS SX2205 GASKETS SX2204 SX2205 Max. working pressure MPa 12 Max. working pressure MPa 13 Continual 330 steam 250 Continual 250 steam 200 Application: water, water vapour, vapour, gas, oil, alcohol, fuel, basic chemicals DENSITY g.cm -3 1,7 2,0 DIN 28 090-2 DENSITY g.cm -3 1,6 1,9 DIN 28 090-2 RECOVERY min. % 55 ASTM F 36 J SPEC. LEAKAGE RATE! mg/(s.m) 0,04 DIN 3535 6 SPEC. LEAKAGE RATE! mg/(s.m) 0,03 DIN 3535 6 LIGHT BLUE branded on one side GREEN branded on one side SX2204 SX2205 FA-M-1-0 FA-AM-1-0 F 712 111 M6 F 712 111 M6 Code: wdb17 Code: wdb01 14
SX2206 GASKETS SX2207 GASKETS SX2206 SX2207 Max. working pressure MPa 10 Max. working pressure MPa 13 Continual 250 steam 250 Continual 250 steam 250 DENSITY g.cm -3 1,6 1,9 DIN 28 090-2 DENSITY g.cm -3 1,8 2,1 DIN 28 090-2 SPEC. LEAKAGE RATE! mg/(s.m) 0,05 DIN 3535 6 RESIDUAL STRESS* 16 h/175 C! MPa 34 DIN 52 913 RECOVERY min. % 55 ASTM F 36 J SPEC. LEAKAGE RATE! mg/(s.m) 0,06 DIN 3535 6 % 5,5 ASTM F 146 BLACK branded on one side BLACK branded on one side SX2206 SX2207 FA-CA-1-0 FA-CA-1-ST F 712 110 M6 F 712 110 M7 Code: wdb03 Code: wdb14 16
SX2208 GASKETS SX2209 GASKETS SX2208 SX2209 Max. working pressure MPa 12 Max. working pressure MPa 14 Continual 250 steam 200 Peak 400 Continual 330 steam 250 DENSITY g.cm -3 1,9 2,2 DIN 28 090-2 SPEC. LEAKAGE RATE! mg/(s.m) 0,08 DIN 3535 6 BLACK (both sides graphited) branded on one side SX2208 FA-MA-1-ST F 712 111 M7 Application: water, water vapour, vapour, gas, oil, alcohol, fuel, basic chemicals DENSITY g.cm -3 1,9 2,2 DIN 28 090-2 RECOVERY min. % 55 ASTM F 36 J SPEC. LEAKAGE RATE! mg/(s.m) 0,04 DIN 3535 6 LIGHT BLUE branded on one side SX2209 FA-M-1-ST F 712 111 M7 Code: wdb23 Code: wdb24 18
SX2210 GASKETS SX2211 GASKETS SX2210 SX2211 Max. working pressure MPa 14 Max. working pressure MPa 10 Continual 250 steam 200 Continual 250 steam 220 Peak 350 DENSITY g.cm -3 1,8 2,2 DIN 28 090-2 DENSITY g.cm -3 1,7 2,0 DIN 28 090-2 RESIDUAL STRESS* 16 h/175 C! MPa 34 DIN 52 913 SPEC. LEAKAGE RATE! mg/(s.m) 0,04 DIN 3535 6 % 4 ASTM F 146 COMPRESSIBILITY % 6 10 ASTM F 36 J RECOVERY min. % 55 ASTM F 36 J SPEC. LEAKAGE RATE! mg/(s.m) 0,05 DIN 3535 6 5 h/150 C! % 2 ASTM F 146 5 h/23 C! % 4 ASTM F 146 GREEN branded on one side BLACK branded on one side SX2210 SX2211 FA-AM-1-ST FA-AZ-1-0 F 712 111 M7 F 712 110 M6 Code: wdb06 Code: wdbxx Page: 1 of 1 Approved: 31.10.2011 Valid since: 1.11.2011 20
SX2213 GASKETS SX2214 GASKETS SX2213 Max. working pressure MPa 4 Application: acid, hydroxid, oil, cooling liquid, basic chemicals Continual 150 steam 130 Peak 200 DENSITY g.cm -3 1,7 2,1 DIN 28 090-2 RESIDUAL STRESS* 16 h/175 C! MPa 20 DIN 52 913 SPEC. LEAKAGE RATE! mg/(s.m) 0,1 DIN 3535 6 SULPHURIC ACID 96% max. % 16 - HYDROGEN CHLORIDE 36% max. % 15 - NITRIC ACID 50% max. % 7 - GREY branded on one side SX2213 FA-A-4Z-0 F 712 122 M5 SX2213 SX 2214 Max. working pressure Max. working pressure MPa MPa 4 13 Max. working temperature Max.working temperature C o c Continual Continual 150 400 steam 130 steam 350 Peak Peak 200 450 Application: acid, hydroxid, oil, cooling liquid, basic chemicals Application: water,water vapor, vapor,gas,oil,alcohol,fuel,basichemicals, cooling liquid DENSITY DENSITY g.cm g.cm 3 1,7-2,0 1,7 2,1 DIN28 DIN 28 090 090-2 - 2 RESIDUAL STRESS* 16 h/175 C! RESIDUAL STRESS*16 h/175/300 C MPa 32 20 / 25 DIN DIN 52 52 913 913 COMPRESSIBILITY MPa % 5 RESIDUAL STRESS* 16 h/300 C 25 15 BS ASTM 7531 F 36 J. RECOVERY COMPRESSIBILITY min. % 5-15 50 ASTM ASTM F F36-J 36 J SPEC. LEAKAGE RATE RECOVERY! mg/(s.m) % 0,1 60 ASTM DIN 3535 F36-J 6 FLUID SPEC.LEAKAGE RESISTANCE RATE THICKNESS CHANGE mg/(s.m) 0,02 DIN 3535-6 SULPHURIC FLUIDRESISTANCE-THICKNESSCHANGE ACID 96% max. % 16 - HYDROGEN ASTM OIL - IRM CHLORIDE 903, CSN ISO 36% 1817 max. % 15 - NITRIC ACID 5 h/150 c 50% max. % 3 7 ASTM F 146 - FLEXIBILITY ASTM FUEL B - CSN ISO 1817 no craks and breaks ASTM F 147 GREY % branded 5 on one side ASTM F 146 5 h/23 C FLEXIBILITY no cracks and breaks SX2213 ASTM F 147 FA-A-4Z-0 BLUE-brandedononeside F 712 122 M5 SX 2214 DIN 28091-2 FA-MAZ F 712 122 BS 7531 GRADE AX a) parametersare valid for thickness2,0 mm b) value validfor thickness1,5 mm Code: wdb05 Code:wdb33 wdb05 Page:1of 1 of 11 Approved: 22.3.2012 15.7.2010 Valid since: 24.3.2012 16.7.2010 22
SX2600 GASKETS SX2601 GASKETS SX2600 Technical Sheet SX2601 Technical Sheet SX2600 Compression moulded PTFE SX2601 Compression moulded PTFE Property Method Unit Specification Property Method Unit Specification CHARACTERISTICS Improved compression and wear resistance; excellent chemical stability; no ageing, no water absorption. Better thermal conductivity. CHARACTERISTICS Excellent resistance to deformation; high recovery; excellent chemical stability; no ageing, no water absorption. Better thermal conductivity. Main applications: It is the most commonly used filler for dynamic seal applications where both rotating and alternating movements are involved, pneumatic, hydraulic and mechanical parts. Bearings; Seals; Gaskets. Statement on suitability for contact with food: We certify that our ptfe products are suitable to be in contact with food as per the following requirements: USA regulations (FDA, Food and Drug Administration, Department of Health and Human Services; Code of Federal Regulations 21 CFR Ch. 1 177.1550 (a) (1) and (b)- Perfluorocarbon Resins. The user must verify that the finished item, made of the semifinished product, would be technically suitable for the requested application. The user must also verify that the finished item may not cause any modification to the organoleptic properties of the food and that the item s technological fitness it is assigned to, may be guaranteed. Main applications: Piping systems, apparatus flanges also with reduced stress or damaged surface, seals, gaskets, valve seats, piston rings. Statement on suitability for contact with food: We certify that our ptfe products are suitable to be in contact with food as per the following requirements: USA regulations (FDA, Food and Drug Administration, Department of Health and Human Services; Code of Federal Regulations 21 CFR Ch. 1 177.1550 (a) (1) and (b)- Perfluorocarbon Resins. The user must verify that the finished item, made of the semifinished product, would be technically suitable for the requested application. The user must also verify that the finished item may not cause any modification to the organoleptic properties of the food and that the item s technological fitness it is assigned to, may be guaranteed. 24
SX2602 SX2602 Technical Sheet SX2602 Compression moulded PTFE Property Method Unit Specification CHARACTERISTICS Excellent resistance to deformation; excellent chemical stability; no ageing, no water absorption. Better thermal conductivity. Main applications: Bearings, seals, gaskets, moldings, valve seats, piston rings. Statement on suitability for contact with foodstuff: We certify that our ptfe products, are suitable to be in contact with food as per the following requirements: USA regulations (FDA, Food and Drug Administration, Department of Health and Human Services; Code of Federal Regulations 21 CFR Ch. 1 177.1550 (a) (1) and (b)- Perfluorocarbon Resins. The user must verify that the finished item, made of the semifinished product, would be technically suitable for the requested application. The user must also verify that the finished item may not cause any modification to the organoleptic properties of the food and that the item s technoiogical fitness it is assigned to, may be guaranteed. 26