Can separate and remove aerosol state oil mist in compressed air and remove particles such as carbon or dust of more than 0.01 μm. Use this product as a pre-filter for compressed air for precision instruments or clean room requiring higher clean air. Modular connection is possible with AM150C to 550C. (For details, refer to page 1.) AM150C to 550C Micro Mist Separator AM50/850 AM Made to Order (For details, refer to page 7.) AM150C AM250C AM350C AM450C AM550C Note) Rated flow (l/min (ANR)) 0 500 00 00 00 Mass (kg) 1 8, 1 4 1 4, 3 8 3 8, 1 2 1 2, 3 4 3 4, 1 AM50 000 100 0.38 0.55 0. 1.4 2.1 4.2.5 Note) Max. flow at 0.7 MPa. Max. flow varies depending on the operating pressure. Refer to Flow Characteristics (page 2) and Maximum Air Flow (page 28). /Free Standing Type AM800 AM00 AM00 Rated flow (l/min (ANR)) 8000 24000 40000 50(2B)IS 50(2B), 80(3B), 0(4B)IS 0(4B), 150(B)IS K K K Mass (kg) 0 2 430 /Piping Support Type AM801 Rated flow (l/min (ANR)) 8000 50(2B)IS K Mass (kg) 50 Specifications Fluid Max. operating pressure Min. operating pressure Proof pressure Ambient and fluid temperature Nominal filtration rating Oil mist density at outlet Element life With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) Oil mist density at 30 mg/m 3 (ANR) blown out by compressor. Accessory Applicable model Bracket assembly (with 2 mounting screws) Caution 1, 1 1 2 11 2, 2 AM01 24000 50(2B), 80(3B), 0(4B)IS K 140 Compressed air 1.0 MPa 0.05 MPa 1.5 MPa 5 to 0 C 0.01 μm (Filtration efficiency:.%) Max. 0.1 mg/m 3 (ANR) (Before saturated with oil, less than 0.01 mg/m 3 (ANR) 0.008 ppm) 2 years (1 year for flange type) or when pressure drop reached 0.1 MPa AM150C AM250C AM350C AM450C AM550C AM50 AM-BM1 AM-BM2 AM-BM3 AM-BM4 AM-BM5 BM5 BM57 Be sure to read this before handling. Refer to back pages 1 and 2 for Safety Instructions, Precautions for Handling Pneumatic evices (M-03-E3A) for Common Precautions, and back pages 3 through to 7 for Specific Product Precautions. 2
.05 0.1 SMC MPa 0.15 0.2.05 0.1 SMC MPa 0.15 0.2 AM150C to 550C Body size 150C 250C 350C 450C 550C Options AM 550C Thread type Type Nil Rc F G 1 N NPT 1 Conforms to ISO117-1. Applicable body size Size 150C 250C 350C 450C 550C 01 1/8 02 1/4 03 3/8 04 1/2 0 3/4 1 Accessory escription Nil B Bracket 2 2 Bracket is included, (but not assembled). Auto rain Specifications/Option Combinations : Available : Not available : Plural options cannot be selected. (i.e. Combinations such as C-FV, -FHV, -ST are not possible.) Auto drain specifications Nil F H R S U T V C F: Rubber material: Fluororubber Fluororubber is used for the parts such as O-ring and gasket. R: - reversal direction Air flow in the separator is changed to right to left. (Air flow direction of the standard: Left to right.) T: With element service indicator Pressure drop 0.1 MPa Saturation of the separator can be observed visually. (Element life check) V: egreasing wash, white vaseline Body/housing is degreasing washed. The lubrication grease for O-ring and gasket is changed to white vaseline. How to Order Made to Order ( How to Order and the applicable models are different from those shown on this page. Be sure to refer to Made to Order.) Option 3 escription Nil F Rubber material: Fluororubber H For medium air pressure (1. MPa) rain guide 1/4 female thread 4 R - reversal direction S U T V With differential pressure switch (125 VAC, 30 VC) 5, Note) With differential pressure switch (30 VC) 5, Note) With element service indicator egreasing wash, white vaseline 4 rain piping and piping for a stop valve such as ball valve are required. 5 ifferential pressure gauge is included, (but not assembled). Only body/housing is degreasing washed. Note) Order U if conformity to the EU directive is required. Auto drain 3 escription Nil rain cock (Without auto drain) C N.C. auto drain N.O. auto drain 3 Refer to Auto rain Specifications/Option Combinations. H: For medium air pressure (1. MPa) Can be used up to 1. MPa at maximum. S: With differential pressure switch (with indicator) Saturation of the separator can be observed visually or by an electrical signal. (Element life check) The rated contact voltage is different from U. Max. contact capacity: VA AC, W C Rated contact voltage (max. operating current): 125 V AC (0.08 A), 30 V C (0.33 A) Reed switch Nil X X15 X17 X2 escription With differential pressure gauge (G40-2-01) With - flange With differential pressure gauge (G40-2-01) and - flange N.C., N.O. auto drain, drain piping type : rain guide 1/4 female threaded Can be pipied to the drain exhaust port. 1/4 female threaded U: With differential pressure switch (with indicator) Saturation of the separator can be observed visually or by an electrical signal. (Element life check) The rated contact voltage is different from S. Max. contact capacity: W C Rated contact voltage (max. operating current): 30 V C (0.33 A) Reed switch Page for details P.8 P. P. P.70 27
Micro Mist Separator AM50/850 AM 50 Body size 50 850 Free standing type AM800/8 to 0 How to Order Piping support type AM 8 00 AM 8 01 Body size 8 Type escription 00 With manual drain cock With auto drain Selection Thread type Type Nil Rc F G N NPT Size Applicable body size 50 850 14 1 1 1 2 2 Accessory escription Nil B Bracket 1 1 Bracket is included, (but not assembled). Auto drain 2 escription Nil rain cock (Without auto drain) 3 N.O. auto drain 2 Refer to Auto rain Specifications/Option Combinations. 3 Body size 850 is equipped with a ball valve (Rc3/8 female threaded). Mount a piping adapter IF-AP0 (page 2) to the ball valve if NPT3/8 female threaded is required. Applicable body size Size AM800, 8 AM 0 AM 0 50(2B)IS K 80(3B)IS K 30 0(4B)IS K 40 150(B)IS K 0 Select a model in accordance with the following procedure taking the inlet pressure and the max. air flow rate into consideration. (Example) Inlet pressure: 0. MPa Max. air flow rate: 5 m 3 /min (ANR) 1. Obtain the intersecting point A of inlet pressure and max. air flow rate in the graph. 2. The AM50 is obtained when the max. flow line is above the intersecting point A in the graph. Note) Make sure to select a model that has the max. flow line above the obtained intersecting point. With a model that has the max. flow line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. Option 2 escription Nil rain guide 1 4 female threaded 4 R - reversal direction T With element service indicator 4 rain piping and piping for a stop valve such as ball valve are required. Auto drain specifications/option Body size 8 Nil X X X15 X17 X2 X12 Auto drain specifications N.O. auto drain rain guide 1 4 Option - reversal direction With element service indicator Type escription 01 With manual drain cock 11 With auto drain Maximum Air Flow Made to Order ( How to Order and the applicable models are different from those shown on this page. Be sure to refer to Made to Order.) AM 0 AM 0, 1 AM80, 81 AM50 AM550C AM450C AM350C AM250C AM150C escription With differential pressure gauge (G40-2-01) With differential pressure switch (With indicator, 125 VAC, 30 VC) With - flange With differential pressure gauge (G40-2-01) and - flange N.C., N.O. auto drain, drain piping type White vaseline specifications R T Auto drain specifications Option R T Page for details P.8 P.8 P. P. P.70 P.70 Auto rain Specifications/ Option Combinations : Available : Not available Max. air flow rate (m 3 /min (ANR)) AM801/811/ 1 Note) Refer to How to Order Bowl Assembly on page 3. Size 50(2B)IS K 80(3B)IS K 30 0(4B)IS K 40 Applicable model AM50 Applicable body size AM8 1 AM 1 Inlet pressure (MPa) 28
Flow Characteristics/Select the model taking the max. flow capacity into consideration. ( Element oil saturation Initial condition) AM150C AM250C AM350C Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. It may cause damage to the element. AM450C AM550C AM50 AM80 /81 Air flow rate (m 3 /min (ANR)) AM 0/ 1 AM 0 Air flow rate (m 3 /min (ANR)) Air flow rate (m 3 /min (ANR)) 2 Air flow rate (m 3 /min (ANR))
Micro Mist Separator Construction AM150C to 550C, AM50 q AM80 /81 / 0/ 1/ 0 r w Component Parts rain No. escription Material Note 1 2 3 Body Housing Sight glass Aluminum die-casted Aluminum die-casted Tempered glass Chrome treated Epoxy coating on inner surface The is aluminum casted. Replacement Parts No. 4 escription Element assembly Material Glass fiber, others Applicable model Except option F For option F AM150C AM-EL150 AM-EL150-F Element e AM250C AM-EL250 AM-EL250-F AM350C AM-EL350 AM-EL350-F Element assembly: With gasket (1 pc.) and O-ring (1 pc.) Refer to back page for replacement of auto drain. Element assemblies for Made to Order (X, X12, X15, X17, X, X2, X) are same as those for standard (see the above table). Component Parts/Material No. escription 1 Filter case 2 Cover Replacement Parts No. escription 3 Element 4 Seal 5 Seal Gasket 7 O-ring AM450C AM-EL450 AM-EL450-F Material NBR NBR V#500 NBR AM550C AM-EL550 AM-EL550-F AM800/8/ 0/ 0 AM801/811/ 1 SGP-E, SS400 SGP-E, SS400 SS400 SGP-E, SS400 Note AM800/8 AM801/811 AM 0 AM 1 AM 0 3174 3174 3174 3 pcs. 3174 3 pcs. 3174 5 pcs. 3148 3148 3148 3 pcs. 3148 3 pcs. 3148 5 pcs. O.112 x I.0 x T3 AL-1S IS B2401G35 1 pc. AL-0S IS B2401G35 1 pc. AM50 AM-EL50 O.112 x I.0 x T3 3 pcs. AL-3S IS B2401G35 3 pcs. Note) Refer to How to Order Bowl Assembly on page 3. Note) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual construction. Refer to dimensions on pages 31 through to 34 for details. AM-EL850 AL-2S IS B2401G35 3 pcs. O.112 x I.0 x T3 5 pcs. AL-31S IS B2401G35 5 pcs. 30
imensions AM150C to 550C H C K R F O AM150C AM250C AM350C AM450C AM550C 31 U G Maintenance space 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 T A 158 172 4 225 25 P Q I L B 14 18 24 M rain C 113 145 1 0 3 7 0 122 øv S Bracket (Accessory) E F 3 7 0 122 A E B G 15 H 173 222 24 278 M5 I 5 80 0 0 24 28 31 33 K 5 8 8 T 7 N Bracket related dimensions U 7 L 12 12 14 18 18 M 7 V N 35 40 12 50 15 55 15 5 Auto drain C: With auto drain (N.C.) : With auto drain (N.O.) rain cock Gray: N.C. Black: N.O. ø one-touch fitting 1/4 female threaded Z 1/4 female threaded 34 Combination of : With auto drain (N.O.) and H: For medium air pressure Option : rain guide 1/4 female threaded S, U: With differential pressure switch (with indicator) Y T: With element service indicator W O 54 80 88 2 P 70 80 5 111 12 Q 2 28 34 50 0 R 4.5 5 5 S 1. 2 2.3 3.2 3.2 X (mm) Element ifferential service pressure indicator related switch related dimensions dimensions W 24 27 32 3 X Y 32 3 42 43 51 Z
Micro Mist Separator imensions AM150C to 550C, AM50 334 12 10 13 253 15 40 Maintenance space 11 180 7 10 150 rain 4.5 Bracket (Accessory) 311 32 85 Auto drain : With auto drain (N.O.) rain cock: Black ø one-touch fitting Option : rain guide 1/4 female threaded 1/4 female threaded T: With element service indicator 55 34 32
imensions 44 18 2 184 348 15 30 24 Maintenance space 13 rain 2 1 2 180 Rc 3/8 female threaded Bracket (Accessory) 42 58 2 x port size 1 Auto drain : With auto drain (N.O.) for 3/8 female threaded 23 Option T: With element service indicator 33
Micro Mist Separator imensions AM801/811/ 1 AM801/811 AM 1 AM800/8/ 0/ 0 AM800/8 AM 0 AM 0 Connection (Flange) 50(2B)IS K 50(2B), 80(3B), 0(4B)IS K rain ORIENTATION A 400 Label øb 280 445 ORIENTATION 3 x øh holes Label øc 150(B) 300(12B) (mm) Connection (Flange) 50(2B), 80(3B)IS K A 500 øb 300 øc 0(8B) 300 E 1300 F 1430 G 15 H Anchor bolt M1 x l400 50(2B), 80(3B), 0(4B)IS K 7 50 400 300 13 1480 1585 24 M x l500 0(4B), 150(B)IS K 870 745 550 300 1380 1 1740 24 M x l500 70 75 E 150 300 F 270 5 G 33 1318 H 3 3 (mm) 887 72 34